pdf

OTi DALI 75/220-240/24 1-4 channel
Electronically stabilized LED Power Supply
Technical
Information
Edition:
May 2013
Subject to change
Technical data
Reference:
for LED modules:
Line voltage, nominal:
Line current, nominal:
Line frequency:
Nominal output voltage:
Nominal module wattage:
Power factor
Power losses
Average efficiency
Full load efficiency:
Stand by power consumption
Partial load:
Perm. voltage fluctuations:
DC voltage operation:
Inrush current:
(Remark)
Max. no. of ECG @ circuit
breakers 10 A (B type):
Max. no. of ECG @ circuit
breakers 16 A (B type):
Control signal
Controls
Dimming
Dimming range
Safety:
Performance:
Radio interference:
Harmonic content:
Immunity:
Temperature range:
Max. case temperature on Tc
Surge capability
ECG Life time:
(Remark)
2013-05-15
A5555990072
OTi DALI 75/220-240/24 1-4 channel
LINEARlight Flex, COINlight, LINEARlight colormix
and 24 V modules
220 – 240 VAC
0.375 A @ 230 V/50 Hz
50/60 Hz
24 VDC +1V/-0,5V
0 - 75W, arbitrarily assigned to 1-4 output channels
PF > 0,95
8.5 W @ 230 V/50 Hz
≥ 87 %
90 %
Typ. 0,5 W @ 230 V/50 Hz
0W – 75W
198 - 254 VAC
No
≤ 36 A
twidth = 270µs(measured at 50% Ipeak)
7
12
DALI (1-4 DALI address, acc. IEC 62386-101 and
IEC 62386-102)
LED specific commands acc. IEC 62386-207
( device type 6 )
Touch DIM (broadcast to active channels)
DALI controls: e.g. DALI BASIC
Touch DIM function: e.g. Touch DIM sensor
PWM (244 Hz)
0-100%
IEC 61347-1, IEC 61347-2-13
IEC 62384
EN 55015 (A1: 2007)
IEC 61000-3-2
IEC 61547
-20 °C to +50 °C
75 °C
L-N: 2kV
50.000h
at tcase = +70 °C at tc point and 10% failure rate
Page 1 of 4
OTi DALI 75/220-240/24 1-4 channel
Electronically stabilized LED Power Supply
Technical
Information
Edition:
May 2013
Subject to change
Galvanic insulation between
primary and secondary side:
Non-load proof:
Short circuit protection:
Overload protection:
Overheating protection:
Wiring:
Wire cross section, primary:
Main wiring
DALI, Touch DIM interface
Secondary:
Wire cross section, secondary:
3,75 kVrms
Yes
Autom. shutoff, reversible
Autom. shutoff, reversible
Autom. shutoff, reversible
Max. cable length
Geometry (l x b x h):
2 x 0,5 - 2,5 mm²
NYM 3x1,5 mm²; NYM 5*1,5 mm²; H05VV-F;
A05VV-F
3 x 0,5 – 2,5 mm2
H03VV-F; H05VV-F; A03VV-F; A05VV-F
LINEARlight POWER Flex, LINEARlight DRAGON,
COINlight OSTAR, etc.
10m with 2,5 mm² massive leads
220 mm x 47 mm x 44 mm
Approvals:
CE
Marks
MM, F
Geometry
2013-05-15
A5555990072
Page 2 of 4
OTi DALI 75/220-240/24 1-4 channel
Electronically stabilized LED Power Supply
Technical
Information
Edition:
May 2013
Subject to change
Wiring diagram
1) Control via DALI control e.g. DALI BASIC:
Number of DALI addresses can be set via 2 Dip switches at the secondary side of the
power supply. The DALI address would be set after a power on cycle.
1-channal device (1 DALI address): 75 W at channel 1
ON
2
1
2- channel device (2 DALI addresses): 75 W split at channel 1
and 2
ON
2
1
3- channel device (3 DALI addresses): 75 W split at channel 1, 2
and 3
ON
2
1
4- channel device (4 DALI addresses): 75 W split at channel 1,
2, 3 and 4
ON
OTi DALI 75 with 4 DALI addresses
OTi DALI 75 with 1 DALI address
2013-05-15
A5555990072
Page 3 of 4
2
1
OTi DALI 75/220-240/24 1-4 channel
Electronically stabilized LED Power Supply
Technical
Information
Edition:
May 2013
Subject to change
2) Control via Touch DIM
Common control of all active channels (depending on DIP switch position, see 1)
Installations notes
The luminaire manufacturer is responsible for providing the required clearances and
creepage distances and also for the protection against electrical shock, especially for the
line and load wires.
Instruction sheet
Please consult the instruction sheet for further important information on dimming
characteristic, wire stripping and wiring limitations in system installations. The instruction
sheet is enclosed to the device or available upon request.
2013-05-15
A5555990072
Page 4 of 4