pdf


POWERTRONIC PT-FIT 50/220-240 I
With cable clamp
For metal halide lamps 50 W
Technical
Information
Edition: June 2011
Subject to change
Technical data
Reference:
Lamp:
System wattage:
Lamp wattage:
Ballast efficency
Line voltage:
Voltage range:
Line frequency:
Line current:
Power factor :
Inrush current:
Max. no. of ECG @ circuit breakers 10 A (B type):
Max. no. of ECG @ circuit breakers 16 A (B type) :
Max. no. of ECG @ circuit breakers 16 A (B type) in
combination with EBN-OS:
Protective conductor current
Operating frequency (50 / 60 Hz Line frequency):
U-OUT:
Maximum working voltage between LH and LL:
Maximum working voltage between LL/LH and PE:
Ambient temperature ta:
Max. temperature at tc test point:
ECG life time:
Overheating protection:
Min.ECG-reset time (by mains interrupt):
Wire cross section input / output line:
Wire stripping:
Max. wiring length ECG/lamp:
Max. capacitance of wire ECG/lamp:
Cable mains:
Cable output:
Max. ignition voltage:
Limited ignition time:
Dimensions (l x w x h):
Distance mounting wholes:
Weight:
Safety:
Radio interference suppression:
Harmonics of line current:
Immunity:
VDE-sign (safety):
VDE-EMC-sign:
PT-FIT 50/220-240 I
HCI 50 W, and other similar commercially
available lamps
54.5 W  1.5 W
50 W  1.5 W
~ 92 %
220 – 240 VAC
198 – 264 VAC
50/60 Hz
0.24 Aeff @ 230 VAC
> 0.95
max. 45 A / 250 µs @ 50%
7
13
32
0.3 mArms
200/240 Hz
250 V
250 V
250 V
-15 °C to +50 °C
+75 °C
30.000 h (@ tc max.) 1)
Power reduction and shutdown at T at the tc point
> 75 °C
0.5 sec
0.75 – 2.5 mm² without ferrule
0.75 – 1.5 mm² with ferrule
5.5 – 6.5 mm
1.50 m
120 pF
NYM-J 3x1.5; NYM-J 2.5; H05VV-F 3x1.5;
NHXMH-J 3x1.5
SIHF-J 3x1.5; SIHF-J 3x2.5; SIHSI 3x1
4.5 kV
20 min
155 mm x 83 mm x 32 mm
163 mm
≈ 270 g
EN 61347-2-12 / IEC 61347-2-12
EN 55015 / CISPR 15
EN 61000-3-2 / IEC 61000-3-2
EN 61547 / IEC 61547
40020649
40027499
Approval marks:
1)
With max. 10% failure rate at max. tc
2011-11-25
page 1 of 3

POWERTRONIC PT-FIT 50/220-240 I
With cable clamp
For metal halide lamps 50 W
Technical
Information
Edition: June 2011
Subject to change
Geometry
Description of the cable clamp compartment
Product number:
Reference
PT-FIT 70/220-240 I
2011-11-25
EAN 10
4008321 648679
page 2 of 3
EAN 40
4008321 648686

POWERTRONIC PT-FIT 50/220-240 I
With cable clamp
For metal halide lamps 50 W
Technical
Information
Edition: June 2011
Subject to change
Thermal characteristics
Ballast losses and lamp heat radiation can lead to heat accumulation in a complete closed case. Therefore
it is necessary to ensure, that the temperature at the measuring point tc does not exceed the maximum
value.
Attention!
For safety reasons disconnect the device before replacing the lamp.
Wiring diagram
Installation by qualified electricians only.
The LUM PE earthing terminal (marked with this symbol:
compartment, which is powered by this control gear.
) is only allowed for earthing of the lamp
Max. lamp cable length is 1.5m; Cable should be twisted for favourable EMC behaviour.
2011-11-25
page 3 of 3