P8TG-xxxxE/Z2:1(H35)LF PM6-SERIES Rev.09-2009 1.5 Watt 2:1 Wide Input Regulated DIP24 Plastic Case 1.5 or 3.5 KV DC I/O Isolation SINGLE and DUAL Output Continuous Short Circuit Prot. Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PM6 series P8TG-xxxxE/Z2:1(H30)LF is a family of cost effective 1.5W single & dual output DC-DC converters with a wide input Voltage of 2:1. These converters are encapsulated in an ultra miniature DIP24 plastic or metal case. High performance features: 1500VDC up to 3500VDC input/output isolation, high efficiency operation, output voltage accuracy of ±1% maximum, wide input range 2:1 and low output ripple and noise. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ 2:1 Wide Input Pi Type 35 mA pk-pk Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation Ripple and Noise (20Mhz bandwidth) Temperature Coefficient ± 1% Indefinite (automatic recovery) ± 0.5% ± 0.5% / ± 1.5% (only 3.3 / ±3.3 Vout Models) 60 mV pk-pk ± 0.02% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency (typical) Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1500 VDC (3500 VDC optional)* 470 pF, typ. 1000 MOhm 266 kHz, typ. 95% rel H > 1.121 Mhrs Physical Specifications Case Material Potting Material Weight Non Conductive Black Plastic Epoxy (UL94V-0 rated) ~ 13.5g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +85°C (ambient) 100°C -40 to +125°C Free Air Convection Soldering 260°C, max. (1.5mm from case 10s.) PM6-Series – P8TG-xxxxE/Z2:1(H35)LF – Single and Dual Output – DIP24 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single/Dual Output ) A) ) (mA d (m mA) ad (mA a ( o ) o ad d L ² L a C ) o . l o l L D n C (u F) (V Fu Mi oL ull VD oad age nt N rrent F %) rent rent ge ( t ( L r r l e a r u u o t r y r l V C C ienc t Vo t Cu put Cu acito put put put Inpu Inpu In Out Out Out Effic Cap Order # SINGLE OUTPUT P8TG-123R3E2:1LF P8TG-1205E2:1LF P8TG-1209E2:1LF P8TG-1212E2:1LF P8TG-1215E2:1LF P8TG-1224E2:1LF P8TG-243R3E2:1LF P8TG-2405E2:1LF P8TG-2409E2:1LF P8TG-2412E2:1LF P8TG-2415E2:1LF P8TG-2424E2:1LF P8TG-483R3E2:1LF P8TG-4805E2:1LF P8TG-4809E2:1LF P8TG-4812E2:1LF P8TG-4815E2:1LF P8TG-4824E2:1LF 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72 36-72 25 25 25 25 25 25 12 12 12 12 12 12 8 8 8 8 8 8 173 169 167 167 167 167 86 84 83 83 83 83 43 42 42 42 42 42 3.3 5 9 12 15 24 3.3 5 9 12 15 24 3.3 5 9 12 15 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 454 300 167 125 100 63 454 300 167 125 100 63 454 300 167 125 100 63 72 74 75 75 75 75 72 74 75 75 75 75 72 74 74 74 74 74 470 470 68 47 22 10 470 470 68 47 22 10 470 470 68 47 22 10 DUAL OUTPUT P8TG-123R3Z2:1LF P8TG-1205Z2:1LF P8TG-1209Z2:1LF P8TG-1212Z2:1LF P8TG-1215Z2:1LF P8TG-1224Z2:1LF P8TG-243R3Z2:1LF P8TG-2405Z2:1LF P8TG-2409Z2:1LF P8TG-2412Z2:1LF P8TG-2415Z2:1LF P8TG-2424Z2:1LF P8TG-483R3Z2:1LF P8TG-4805Z2:1LF P8TG-4809Z2:1LF P8TG-4812Z2:1LF P8TG-4815Z2:1LF P8TG-4824Z2:1LF 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72 36-72 25 25 25 25 25 25 12 12 12 12 12 12 8 8 8 8 8 8 173 169 167 167 167 167 86 84 83 83 83 83 43 42 42 42 42 42 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ± 227 ± 150 ± 84 ± 63 ± 50 ± 32 ± 227 ± 150 ± 84 ± 63 ± 50 ± 32 ± 227 ± 150 ± 84 ± 63 ± 50 ± 32 72 74 75 75 75 75 72 74 75 75 75 75 72 74 74 74 74 74 ± 220 ± 220 ± 33 ± 22 ± 10 ± 10 ± 220 ± 220 ± 33 ± 22 ± 10 ± 10 ± 220 ± 220 ± 33 ± 22 ± 10 ± 10 If you need other specifications, please enquire. * For optional 3.5kV DC I/O Isolation, please add “H35” before LF! Example: P8TG-1205Z2:1H35LF for 3.5kV PM6-Series – P8TG-xxxxE/Z2:1(H35)LF – Single and Dual Output – DIP24 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 0.25 (0.01) 20.32 (0.80) 15.24 (0.60) Package / Pinning / Derating # 1 2 3 9 10 11 12 13 14 15 16 22 23 24 others SINGLE +Vin N.C. N.C. Omitted - Vout +Vout - Vin - Vin +Vout - Vout Omitted N.C. N.C. +Vin PIN CONNECTIONS DUAL SINGLE 3.5KV DUAL 3.5KV +Vin Omitted Omitted - Vout - Vin - Vin Common - Vin - Vin Omitted Omitted Common Common Omitted Omitted +Vout N.C. - Vout - Vin Omitted Omitted - Vin Omitted Omitted +Vout +Vout +Vout Common Omitted Omitted Omitted - Vout Common Common +Vin +Vin - Vout +Vin +Vin +Vin Omitted Omitted Omitted App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH. ² = Tested by nominal Vin and constant resistive load. PM6-Series – P8TG-xxxxE/Z2:1(H35)LF – Single and Dual Output – DIP24 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3