pdf

www.osram.com/LED-systems
PrevaLED® Cube – PL-CUBE-AC-xxxx-8y0-230V-G2
xxxx =2000lm, 3000lm; y = 3 for 3000K, 4 for 4000K
Technical information
Benefits






Power on-board through integrated driver electronics
Low height of the Optical Contact Area (OCA) of 18.6mm
for compact luminaire designs
Near Lambertian light distribution at 110° for best quality of
light in diffuser as well as reflector based applications
Robust design for easy thermal management and long
lifetime
Industry standard LES for use with reflector accessories
Safety through thermal shutdown
Applications
For general illumination in:
 Hospitality: Hotels, Restaurants
 Public, Commercial & Office buildings
 Corridors
 Shops
 Secondary rooms: garages, storage, …
(picture for reference only)
Technical operating data
Product
Color
typ. Power [W]
PL-CUBE-AC-2000-830-230V-G2 Warm white
PL-CUBE-AC-2000-840-230V-G2 Cool white
PL-CUBE-AC-3000-830-230V-G2 Warm white
PL-CUBE-AC-3000-840-230V-G2 Cool white
Product
PL-CUBE-AC-2000-830-230V-G2
PL-CUBE-AC-2000-840-230V-G2
PL-CUBE-AC-3000-830-230V-G2
PL-CUBE-AC-3000-840-230V-G2
Color
Temp. [K]
nom. lum.
flux [lm]
Beam
angle [°]
27.8
rated
Voltage
[Vac]
230
3000
2000
110
25.3
230
4000
2000
110
42.7
230
3000
3000
110
38.4
230
4000
3000
110
1
min. lum
flux [lm]
1800
max. lum
flux [lm]
2400
min. Power
[W]
max Power [W]
tp [°C]
tc [°C]
25
31
70
90
1800
2400
23
28
70
90
2700
3600
38
47
70
90
2700
3600
35
42
70
90
Technical features


1
Nominal luminous flux: typ. 2000lm and 3000lm
Light colors:
o Warm white (3000K)
o Cool white (4000K)
tp refers to the temperature at the tc-point related to the performance of the LED light engine (see IEC/PAS 62717).
Note:
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect
statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the
typical data.
PrevaLED® Cube AC G2
Edition: 06.2014
1/3
www.osram.com/LED-systems









Color rendering index: typ. 83
System efficacy: typ > 84 lm/W at 4000K
Dimensions: H: 21.1 mm, W x L: 81.6 x 82.8 mm
Operation with mains voltage: 220 – 240 Vac; 50/60Hz
Power factor > 0.9
Modulation of 100Hz with 40% depth
L70B50 @ 50,000 hours at tp=70°C (see IEC/PAS 62717)
L0C10 @ >42,000 hours for 2000lm and L0C10 >50,000 hours for 3000lm at tp=70°C (see IEC/PAS 62717)
Specialized mechanical adaptor (PL-CUBE-ADP) to raise the module to the same height as competitor products.
Minimum and maximum ratings
Product
PL-CUBE-AC-xxxx-8y0-230V-G2
Operating temperature
2
at tc-point [°C]
-20 … 90
2
Storage temperature [°C]
-20 … 85
Operating Voltage range
3
[Vac]
220 … 240
The tc-point is at the back of the LED engine below the centre of the Light Emitting Surface (LES).
The LED light engine is designed to work on 230Vac mains voltage. Reverse wiring will not impede the operation of the LED
light engine.
Dimensions & mechanical data
LES diameter
Total height
OCA height
Footprint
Mounting
Optics
Weight (g)
Solid wire cross-section
(mm²)
Stranded wire cross
section (mm², no ferrule
to be used)
LEP-CUB-AC-8x0-G1
61 mm
21 mm
18.6 mm
81.6 x 82.8 mm²
3 x M4 screws
PC diffuser
81.6
0.4 – 0.75
(AWG 18 – 22)
t
0.4 – 0.75
(AWG 18 – 22)
location of tc point
(dimensions rounded)
Standard Compliance
CE
Eye Security
Ingress Protection
Environment
EN 62031, EN 55015, EN 61547, EN 61000-3-2, EN 61000-3-3
EN 62471, Risk Group 1
Dry Location, IP 20
RoHS
Safety information






2
3
The LED light engine itself and all its components may not be mechanically stressed.
The LED light engine needs to be mounted on a heat sink providing adequate thermal dissipation.
Do not damage or destroy conducting paths on the circuit board.
The LED light engine is mains voltage operated. All related safety precautions need to be observed.
The LED light engine cannot be operated safely when the housing is mechanically damaged.
Installation of LED light engine needs to be made with regard to all applicable electrical and safety standards. Only
qualified personnel should be allowed to perform installation.
Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED light
engine. The temperature of the LED light engine must be measured at the tc-point according to EN60598-1 in a thermally
stable state with a temperature sensor or a temperature sensitive label. For exact location of the tc-point see drawing above.
Further information is provided in the related application guide.
Exceeding maximum ratings for operating voltage range will lead to a change in performance and lifetime and could
damage the LED light engine.
Note:
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect
statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the
typical data.
PrevaLED® Cube AC G2
Edition: 06.2014
2/3
www.osram.com/LED-systems





Parallel connection of the LED light engines is highly recommended as safe electrical operation mode. Serial
connection of the LED light engines is forbidden.
These light engines are based on 100Hz technology and modulate the light amplitude at this frequency. Therefore
the LE must not be applied in rooms with fast moving parts such as rotating machines, if there is a risk of frequency
interference. Fast moving parts might appear to stand still although being in motion. Possible interference with
camera/display systems should be checked.
Damage by corrosion will not be honored as materials defect claim. It is the user's responsibility to provide suitable
protection against corrosive agents, such as moisture, condensation and other harmful elements.
Pay attention not to exceed the maximum operation temperature 90°C at the tc point when the modules are used in
an enclosed environment.
The design of the housing/luminaire should be according to the IP
standards applicable for the intended application.
Ordering guide
LED light engines
Order No 20
pieces
Quantity (pieces)
Order No 1 piece
Quantity
(pieces)
PL-CUBE-AC-2000-830-230V-G2
4052899909816
20
4052899909496
1
PL-CUBE-AC-2000-840-230V-G2
4052899909823
20
4052899909502
1
PL-CUBE-AC-3000-830-230V-G2
4052899909878
20
4052899909557
1
PL-CUBE-AC-3000-840-230V-G2
4052899909885
20
4052899909564
1
Order No 20
pieces
Quantity (pieces)
Order No 1 piece
Quantity
(pieces)
4052899055605
20
4052899055599
1
Product
Accessory
PL-CUBE-ADP
Sales and technical support
OSRAM GmbH
Sales and technical support is given by the local OSRAM
subsidiaries.
Marcel-Breuer-Straße 6
80807 Munich, Germany
www.osram.com
+49.89.6213-0 (Headquarter)
+49.89.6213-6000 (Customer-Service-Center)
On the OSRAM website all subsidiaries are listed with
complete address and phone numbers.
Links and related further information
OSRAM LED Systems
OSRAM catalogue
General information
Note:
www.osram.com/prevaled
catalog.osram.com
www.osram.com
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect
statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the
typical data.
PrevaLED® Cube AC G2
Edition: 06.2014
3/3