Data Sheet

TDA18204HN
Cable pre-processor and low-power silicon tuner
Rev. 2 — 12 July 2013
Product short data sheet
1. General description
TDA18204HN is a cable pre-processor coupled with a low-power silicon tuner to address
the front-end part of cable modems and gateways.
The cable pre-processor allows for smooth signal processing by a wideband receiver
connected to its output. It inputs single ended cable signal and provides amplification, tilt
compensation in the 42 MHz to 1 GHz bandwidth, low-pass filtering to reject signals
above 1 GHz and provides a balanced output signal.
The low-power silicon tuner can be used for the battery-powered “emergency call”
function of the Cable gateways. It provides a single channel reception using as little power
as possible. The output signal of the low-power silicon tuner section is a low-IF signal,
interfacing a narrowband ADC at system level.
TDA18204HN copes with all cable standards worldwide and interfaces ideally to NXP Full
Spectrum Transceiver (FST) product family to make the full multi-stream RF front end of a
cable receiver or cable modem in a very small form factor, while providing with no
additional component the low-power path for VoIP in battery operated mode.
2. Features and benefits








RF front end for FST family of products
Very low-Noise Figure (NF); 3.9 dB typical
Very low-power consumption; 360 mW in wideband application
Direct interfacing to the cable with single ended input
Covers all cable standards worldwide
Input frequency range up to 1 GHz
Gain control to provide a stable output power irrespective of the input power
Cable tilt correction to provide a flat output spectrum whatever the distance from the
cable head-end to the user
 Balanced output to drive directly a high-performance ADC like the one implemented in
NXP FST products
 Narrowband low-power silicon tuner
 Additional outputs for optional standalone tuners or Loop-Through (LT)
TDA18204HN
NXP Semiconductors
Cable pre-processor and low-power silicon tuner
3. Quick reference data
Table 1.
Quick reference data
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
3.13
3.3
3.47
V
Standby mode
-
6
-
mA
Standby mode with LT ON
-
52
-
mA
-
109
-
mA
42
-
1002
MHz
Cable pre-processor
VCC
supply voltage
ICC
supply current
operation mode
fRF
RF frequency
[1]
channel edge
NF
noise figure
maximum gain; f = 500 MHz
-
3.9
-
dB
Gv(max)
maximum voltage gain
f = 500 MHz
-
41
-
dB
Gv(min)
minimum voltage gain
gtc
gain tilt compensation
-
17
-
dB
setting 1
[2]
-
+15.5
-
dB
setting 2
[2]
-
+10.5
-
dB
setting 3
[2]
-
+5.5
-
dB
setting 4
[2]
-
+3.5
-
dB
setting 5
[2]
-
0
-
dB
setting 6
[2]
-
4.5
-
dB
setting 7
[2]
-
8
-
dB
CTB
composite triple beat
135 channels at 75 dBV, flat plan.
worst case in frequency range
[3]
-
60
-
dB
CSO
composite second-order
distortion
135 channels at 75 dBV, flat plan.
worst case in frequency range
[3]
-
57
-
dB
Low-power silicon tuner
fRF
RF frequency
channel edge
42
-
1002
MHz
NFtun
tuner noise figure
maximum gain
-
4.3
-
dB
n
phase noise
worst case in the RF range
10 kHz
-
90
-
dBc/Hz
100 kHz
-
100
-
dBc/Hz
P
power dissipation
-
560
-
mW
image
image rejection
-
62
-
dB
[1]
Without GPO and LTO.
[2]
A positive tilt correction (for instance: +15 dB) means that the Tilt EQ compensates for a low-pass effect on the cable. A negative tilt
correction means that the Tilt EQ compensates for a high-pass effect on the cable.gtc value is normalized with setting 5 as a reference.
[3]
NTSC 135 frequency plan.
4. Ordering information
Table 2.
Ordering information
Type number
TDA18204HN/C1
TDA18204HN_SDS
Product short data sheet
Package
Name
Description
Version
HVQFN36
plastic thermal enhanced very thin quad flat package; no leads; 36
terminals; body 6  6  0.85 mm
SOT1092-3
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 12 July 2013
© NXP B.V. 2013. All rights reserved.
2 of 8
TDA18204HN
NXP Semiconductors
Cable pre-processor and low-power silicon tuner
5. Block diagram
SDA
AS
SCL
AGC_CLK_GATE
AGC_UP_DOWN
AGC
I2C-BUS
TILT
comp
LNA1
S2D
AAF
RFOUT_P
RFOUT_N
RFIN
LNA2 WB
XTAL_P
XTAL_N
PLL
LTO
LNA2 NB
IFO_P
IFO_N
MTO
RF
filter
mixer
IF
filter
IF
AGC
TDA18204
VIFAGC
aaa-003388
Fig 1.
Block diagram
6. Limiting values
Table 3.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
VCC
supply voltage
VI
input voltage
Conditions
Tstg
storage temperature
Tj
junction temperature
VESD
electrostatic discharge
voltage
[1]
It withstands class 3A of JEDEC standard.
[2]
It withstands class IV of JEDEC standard.
Min
Max
Unit
0.3
+3.6
V
VCC < 3.3 V
0.3
VCC + 0.3
V
VCC > 3.3 V
0.3
+3.6
V
40
+150
C
-
150
C
EIA/JESD22-A114
(HBM)
[1]
2
+2
kV
EIA/JESD22-C101-C
(FCDM)
[2]
0.75
-
kV
7. Abbreviations
Table 4.
Acronym
TDA18204HN_SDS
Product short data sheet
Abbreviations
Description
AAF
Anti Aliasing Filter
ADC
Analog-to-Digital Converter
AGC
Automatic Gain Control
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 12 July 2013
© NXP B.V. 2013. All rights reserved.
3 of 8
TDA18204HN
NXP Semiconductors
Cable pre-processor and low-power silicon tuner
Table 4.
Abbreviations …continued
Acronym
Description
CTRL
ConTRoLer
Det
Detector
DOCSIS
Data Over Cable Service Interface Specification
FCDM
Field-induced Charged Device Model
FST
Full Spectrum Transceiver
GPO
General-Purpose Output
HBM
Human Body Model
IC
Integrated Circuit
LNA
Low Noise Amplifier
LT
Loop-Through
LTO
Loop-Through Output
MTO
Multi-Tuners Output
NB
Narrow Band
NF
Noise Figure
PCB
Printed-Circuit Board
RF
Radio Frequency
S2D
Single-to-Differential
SCL
Serial CLock
SDA
Serial Data
STB
Set-Top Box
TiltEQ
Tilt EQualizer
TOP
Take-Over Point
VoIP
Voice over IP
WB
Wide Band
8. Revision history
Table 5.
Revision history
Document ID
TDA18204HN_SDS
[1]
v.2[1]
Release date
Data sheet status
Change notice
Supersedes
20130712
Product short data sheet
-
-
Revision 1 is not available.
TDA18204HN_SDS
Product short data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 12 July 2013
© NXP B.V. 2013. All rights reserved.
4 of 8
TDA18204HN
NXP Semiconductors
Cable pre-processor and low-power silicon tuner
9. Legal information
9.1
Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
9.2
Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
9.3
Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
TDA18204HN_SDS
Product short data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 12 July 2013
© NXP B.V. 2013. All rights reserved.
5 of 8
TDA18204HN
NXP Semiconductors
Cable pre-processor and low-power silicon tuner
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
9.4
Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
10. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
TDA18204HN_SDS
Product short data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 12 July 2013
© NXP B.V. 2013. All rights reserved.
6 of 8
TDA18204HN
NXP Semiconductors
Cable pre-processor and low-power silicon tuner
11. Tables
Table 1.
Table 2.
Table 3.
Quick reference data . . . . . . . . . . . . . . . . . . . . .2
Ordering information . . . . . . . . . . . . . . . . . . . . .2
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . . .3
Table 4.
Table 5.
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . 4
12. Figures
Fig 1.
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
TDA18204HN_SDS
Product short data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 12 July 2013
© NXP B.V. 2013. All rights reserved.
7 of 8
TDA18204HN
NXP Semiconductors
Cable pre-processor and low-power silicon tuner
13. Contents
1
2
3
4
5
6
7
8
9
9.1
9.2
9.3
9.4
10
11
12
13
General description . . . . . . . . . . . . . . . . . . . . . .
Features and benefits . . . . . . . . . . . . . . . . . . . .
Quick reference data . . . . . . . . . . . . . . . . . . . . .
Ordering information . . . . . . . . . . . . . . . . . . . . .
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . .
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . . . .
Legal information. . . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information. . . . . . . . . . . . . . . . . . . . . .
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
2
3
3
3
4
5
5
5
5
6
6
7
7
8
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2013.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 12 July 2013
Document identifier: TDA18204HN_SDS