PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com HIGH PERFORMANCE DIFFERENTIAL OSCILLATOR SERIES „DLPO-5“ 156.25000—161.1328MHz FEATURES APPLICATIONS + + + + + + + + + + + 10GB Ethernet, SONET, SATA, SAS, Fibre Channel, PCI Express, + Telecom, networking, instrumentation, storage, servers Differential Oscillator for Low Cost Low Power Consumption Extremely low RMS phase jitter Excellent long time reliability Very tight frequency stability as low as ±10 ppm over –40/+85°C LVPECL and LVDS output signals Outstanding long term aging Configurable positive frequency shift, +25, +50, or +75 ppm Industry-standard packages: 3.2x2.5; 5.0x3.2; 7.0x5.0 mm Pb-free, RoHS and REACH compliant / MSL1 @ 260°C GENERAL DATA PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT 2.97 3.3 3.63 V 2.25 2.5 2.75 V 2.25 – 3.63 CONDITION LVPECL AND LVDS, COMMON ELECTRICAL CHARACTERISTICS Supply Voltage Output Frequency Range Frequency Stability VDD f F_stab 156.25000, 156.253906, 156.257812, 156.261718, 161.132800 V Termination schemes in Figures 1 and 2 - XX ordering code MHz 156.253906 MHz, +25 PPM from 156.250000 156.257812 MHz, +50 PPM from 156.250000 156.261718 MHz, +75 PPM from 156.250000 -10 – +10 ppm Inclusive of initial tolerance, operating temperature, -20 – +20 ppm rated power supply voltage, and load variations -25 – +25 ppm -50 – +50 ppm First Year Aging F_aging1 -2 – +2 ppm 25°C 10-year Aging F_aging10 -5 – +5 ppm 25°C T_use -40 – +85 °C Industrial -20 – +70 °C Extended Commercial Operating Temperature Range Input Voltage High VIH 70% – – VDD Pin 1, OE or ST Input Voltage Low VIL – – 30% VDD Pin 1, OE or ST Input Pull-up Impedance Z_in – 100 250 kΩ Pin 1, OE logic high or logic low, or ST logic high 2 – – MΩ Pin 1, ST logic low Start-up Time T_start – 6 10 ms Measured from the time VDD reaches its rated minimum value. Resume Time T_resume – 6 10 ms In Standby mode, measured from the time ST pin crosses 50% threshold. DC 45 – 55 % Contact PETERMANN-TECHNIK for tighter duty cycle Duty Cycle CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 1 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com GENERAL DATA (continued) PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT CONDITION IDD – 61 69 mA Excluding Load Termination Current, VDD = 3.3V or 2.5V I_OE – – 35 mA OE = Low Output Disable Leakage Current I_leak – – 1 µA OE = Low Standby Current I_std – – 100 µA ST = Low, for all VDDs I_driver – – 30 mA Maximum average current drawn from OUT+ or OUT- Output High Voltage VOH VDD-1.1 – VDD-0.7 V See Figure 1(a) Output Low Voltage VOL VDD-1.9 – VDD-1.5 V See Figure 1(a) V_Swing 1.2 1.6 2.0 V See Figure 1(b) Rise/Fall Time Tr, Tf – 300 500 ps 20% to 80%, see Figure 1(a) OE Enable/Disable Time T_oe – – 120 ns f = 156.25 MHz - For other frequencies, T_oe = 100ns + 3 period RMS Phase Jitter (random) T_phj – 0.25 0.3 ps IEEE802.3-2005 10GbE jitter measurement specifications IDD – 47 55 mA Excluding Load Termination Current, VDD = 3.3V or 2.5V I_OE – – 35 mA OE = Low LVPECL, DC AND AC CHARACTERISTICS Current Consumption OE Disable Supply Current Maximum Output Current Output Differential Voltage Swing LVDS, DC AND AC CHARACTERISTICS Current Consumption OE Disable Supply Current Differential Output Voltage VOD 250 350 450 mV See Figure 2 Output Disable Leakage Current I_leak – – 1 µA OE = Low Standby Current I_std – – 100 µA ST = Low, for all VDDs VOD Magnitude Change VOD – – 50 mV See Figure 2 VOS 1.125 1.2 1.375 V See Figure 2 VOS Magnitude Change VOS – – 50 mV See Figure 2 Rise/Fall Time Tr, Tf – 495 600 ps 20% to 80%, see Figure 2 OE Enable/Disable Time T_oe – – 115 ns f = 156.25 MHz - For other frequencies, T_oe = 100ns + 3 period RMS Phase Jitter (random) T_phj – 0.25 0.3 ps IEEE802.3-2005 10GbE jitter measurement specifications Offset Voltage EXCELLENT RELIABILITY DATA MTBF 500 million hours Shock Resistance: 10.000 g Vibration Resistance: 70 g PIN DESCRIPTION PIN SYMBOL TOP VIEW FUNCTIONALITY OE Input H or Open: specified frequency output L: output is high impedance ST Input H or Open: specified frequency output L: Device goes to sleep mode. Supply current reduces to I_std. 2 NC NA 3 GND Power VDD Power Supply Ground 4 OUT+ Output Oscillator output 5 OUT- Output Complementary oscillator output 6 VDD Power Power Supply Voltage 1 No Connect; Leave it floating or connect to GND for better heat dissipation CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS OE/ST 1 6 VDD NC 2 5 OUT- GND 3 4 OUT+ PAGE 2 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com WAVE FORM DIAGRAMS FIGURE 1(A). LVPECL VOLTAGE LEVELS PER DIFFERENTIAL PIN (OUT+/OUT-) OUT80% 80% 20% VOH 20% OUT+ Tr VOL Tf GND FIGURE 1(B). LVPECL VOLTAGE LEVELS ACROSS DIFFERENTIAL PAIR V_ Swing 0V t FIGURE 2. LVDS VOLTAGE LEVELS PER DIFFERENTIAL PIN (OUT+/OUT-) OUT80% 80% VOD 20% 20% OUT+ VOS Tr Tf GND CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 3 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TERMINATION DIAGRAMS LVPECL: FIGURE 3. LVPECL TYPICAL TERMINATION VDD OUT+ Z0 = 50 Ω D+ LVPECL Driver Receiver Device OUT- Z0 = 50 Ω D50 Ω 50 Ω VTT = VDD - 2.0V FIGURE 4. LVPECL AC COUPLED TERMINATION VDD= 3.3V => R1 = 100 to 150 Ω VDD= 2.5V => R1 = 75 Ω VDD OUT+ D+ Z0 = 50 Ω 100nF Receiver Device LVPECL Driver 100nF OUT- Z0 = 50 Ω R1 R1 D50 Ω 50 Ω VTT FIGURE 5. LVPECL WITH THEVENIN TYPICAL TERMINATION VDD = 3.3V => R1 = R3 = 133 Ω and R2 = R4 = 82 Ω VDD = 2.5V => R1 = R3 = 250 Ω and R2 = R4 = 62.5 Ω VDD OUT+ VDD R1 R3 Z0 = 50 Ω D+ LVPECL Driver OUT- Receiver Device Z0 = 50 Ω DR2 CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS R4 PAGE 4 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TERMINATION DIAGRAMS LVDS: FIGURE 6. LVDS SINGLE TERMINATION (LOAD TERMINATED) VDD OUT+ Z0 = 50 Ω 100 Ω Drive Device OUT- D+ Z0 = 50 Ω CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS Receiver Device D- PAGE 5 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) [1] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 3.2X 2.5 X 0.75 MM #2 #6 #5 #4 #1 #2 #3 1.00 1.6 #3 0.6 0.65 0.75±0.05 #1 2.25 2.20 #4 0.7 #5 0.9 3.2±0.05 2.5±0.05 #6 1.05 RECOMMENDED LAND PATTERN (UNIT:MM) [1] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 5.0X 3.2 X 0.75 MM #2 #6 #5 #4 #1 #2 #3 1.20 2.20 #3 0.64 0.90 0.75±0.05 #1 2.54 2.54 #4 0.9 #5 1.20 5.0±0.10 3.2±0.10 #6 RECOMMENDED LAND PATTERN (UNIT:MM) [1] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 7.0X 5.0 X 0.90 MM #2 #6 #5 #4 #1 #2 #3 #3 3.80 1.40 0.90±0.10 #1 5.08 5.08 #4 1.60 1.10 #5 2.60 7.0±0.10 5.0±0.10 #6 1.60 Note: 1. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 6 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com ORDERING INFORMATION OSCILLATOR FAMILY DLPO5 SUPPLY VOLTAGE “25“ for 2.5V “33“ for 3.3V TEMPERATURE RANGE “M” for -20 +70°C “W” for -40 +85°C SIGNALING TYPE FREQUENCY “1” = LVPECL “2” = LVDS 156.250000 MHZ 156.253906 MHZ 156.257812 MHZ 156.261718 MHZ 161.132800 MHZ DLPO5 33-3225-E-25-M-156.250MHz-T-1 FREQUENCY STABILITY “10” for ±10 PPM “20” for ±20 PPM “25” for ±25 PPM “50” for ±50 PPM PACKAGE SIZE “3225” for 3.2 X 2.5 mm “5032” for 5.0 X 3.2 mm “7050” for 7.0 X 5.0 mm PACKING METHOD “B“ for Bulks or Tubes “T” for Tape & Reel FEATURE PIN 1 “E” for OUTPUT ENABLE “S” for STANDBY EXAMPLE: DLPO533-3225-E-25-M-156.250MHz-T-1 PLEASE INDICATE YOUR REQUIRED PARAMETERS SAMPLES ARE AVAILABLE WITHIN A SHORT DELIVERY PERIOD! CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 7 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com REFLOW SOLDER PROFILE PREMIUM QUALITY BY PETERMANN-TECHNIK OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH. THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS. © PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 8 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014