PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com LOW POWER OSCILLATOR 200—1000 kHz SERIES „LPO“ FEATURES APPLICATIONS + + + + + + + + + + + + + + + High Performance Oscillator for Low Cost Excellent long time reliability LVCMOS/LVTTL compatible output Frequency stability as low as ± 20 PPM Four packages from 2.5x2.0 ~ 7.0x5.0mm available Typical current consumption of 5.7 mA in active mode Standby or output enable modes Outstanding mechanical robustness for portable applications Ultra short lead time Ideal for consumer electronics, audio applications, etc. Pb-free, RoHS and REACH compliant / MSL1@260° Audio amplifiers Low speed Serial I/O MCU clocking etc. GENERAL DATA PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT CONDITION f 200 - 1000 kHz Contact Petermann-Technik for < 200kHz F_stab -20 - +20 PPM -25 - +25 PPM -30 - +30 PPM FREQUENCY Output Frequency Range FREQUENCY STABILITY Frequency Stability 25°C Aging Inclusive of: Initial stability, operating temperature, rated power supply voltage change, load change, shock and vibration. ± 20 PPM available in extended commercial temperature of about –20/+70°C only -50 - +50 PPM Ag -1.0 - -1.0 PPM VDD 1.71 1.8 1.89 V 2.25 2.5 2.75 V 2.52 2.8 3.08 V 2.97 3.3 3.63 V - 5.9 6.9 mA No load condition, f = 400 kHz, VDD = 2.5 V, 2.8 V or 3.3 V - 5.7 6.6 mA No load condition, f = 400 kHz, VDD = 1.8 V - 2.4 4.3 µA ST = GND, VDD = 3.3 V, output is weakly pulled down - 1.2 2.2 µA ST = GND, VDD = 2.5 or 2.8 V, output is weakly pulled down - 0.4 0.8 µA ST = GND, VDD = 1.8 V, output is weakly pulled down DC 45 50 55 % All VDDs Tr, Tf - 1.0 2.0 ns 20% - 80% VDD=2.5V or 2.8V, 3.3V, 15pF load - 1.3 2.5 ns 20% - 80% VDD=1.8V, 15pF load VOH 90% - - VDD IOH = -4 mA (VDD = 3.3 V) IOH = -3 mA (VDD = 2.8 V and Vdd = 2.5 V) IOH = -2 mA (VDD = 1.8 V) VOL - - 10% VDD IOL = 4 mA (VDD = 3.3 V) IOL = 3 mA (VDD = 2.8 V and Vdd = 2.5 V) IOL = 2 mA (VDD = 1.8 V) Ld - - 15pF 1st Year at 25°C SUPPLY VOLTAGE AND CURRENT CONSUMPTION Supply Voltage Current Consumption Standby Current IDD I_std LVCMOS OUTPUT CHARACTERISTICS Duty Cycle Rise/Fall Time Output Voltage High Output Voltage Low Output load CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS At maximum frequency and supply voltage. Contact Petermann-Technik for higher output load option PAGE 1 OF 6 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com GENERAL DATA (continued) PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT CONDITION T_use -20 – +70 °C Extended Commercial -40 – +85 °C Industrial -55 – +125 °C Storage OPERATING TEMPERATURE RANGE Operating Temperature Range Storage Temperature Range T_stor INPUT CHARCTERISTICS AND STARTUP/RESUME TIMING Input Voltage High VIH 70% – – VDD Pin 1, OE or ST Input Voltage Low VIL – – 30% VDD Pin 1, OE or ST Startup Time T_osc – – 10 ms Measured from the time VDD reaches its rated minimum value Resume Time T_resume – 3 4 ms Measured from the time ST pin crosses 50% threshold - 11 17 ps f = 400 kHz, VDD = 2.5 V, 2.8 V or 3.3 V - 12 17 ps f = 400 kHz, VDD = 1.8 V JITTER RMS Period Jitter T_jitt EXCELLENT RELIABILITY DATA MTBF 500 million hours Shock Resistance 10.000 g Vibration Resistance 70 g PIN DESCRIPTION TABLES SMD MAP PIN # 1 FUNCTIONALITY PIN CONNECTION H or Open[1]: specified frequency output 1 OE/ST L: output is high impedance 2 GND 3 CLK 4 VDD OE ST H or Open: specified frequency output L: output is low level (weak pull down). Oscillation stops Note: 1. In 1.8 V mode, a resistor of <100 kΩ between OE pin and VDD is recommended. TIMING DIAGRAMS FIGURE 1. STARTUP TIMING (ST/=OE MODE) 90%VDD, 2.5/2.8/3.3V parts 95%VDD, 1.8V parts VDD Pin 4 Voltage FIGURE 2. STANDBY RESUME TIMING (ST MODE ONLY) 50%VDD VDD ST Voltage T_resume T_start CLK Output T_start: Time to start from power-off CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS CLK Output T_resume: Time to resume from ST PAGE 2 OF 6 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) (2) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 2.5 X 2.0 X 0.75 MM #1 1.9 1.00 #3 #3 #1 #2 #2 1.0 1.1 1.5 #4 0.5 2.5±0.10 2.0±0.10 #4 1.1 0.75±0.05 0.75 RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 3.2 X 2.5 X 0.75 MM #1 2.2 2.1 #3 #3 #1 #2 #2 1.2 0.9 1.9 #4 0.7 3.2±0.15 2.5±0.15 #4 1.4 0.75±0.05 0.9 RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 5.0 X 3.2 X 0.75 MM #3 #1 #2 #2 1.1 1.6 2.2 #4 1.15 1.5 0.75±0.05 #1 2.54 2.39 #3 0.8 5.0±0.15 3.2±0.15 #4 Note: 2. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 3 OF 6 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 7.0 X 5.0 X 0.90 MM #3 #1 #2 #2 1.1 2.0 3.81 #4 1.4 2.2 0.90±0.10 #1 5.08 5.08 #3 2.6 7.0±0.15 5.0±0.15 #4 REFLOW SOLDER PROFILE CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 4 OF 6 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com ORDERING INFORMATION OSCILLATOR FAMILY TEMPERATURE RANGE SUPPLY VOLTAGE “18“ “25“ “28“ “33“ LPO for 1.8V for 2.5V for 2.8V for 3.3V FREQUENCY 200 TO 1000 kHz “C” for 0 +70°C “D” for -10 +70°C “M” for -20 +70°C “W” for -40 +85°C LPO 33-2520-20-W-1000kHz-T-S FREQUENCY STABILITY “20” for ±20 PPM “25” for ±25 PPM “30” for ±30 PPM “50” for ±50 PPM PACKAGE SIZE PACKING METHOD “B” for BULKS or TUBES “T” for TAPE & REEL OUTPUT DRIVE STRENGTH “2520” for 2.5 X 2.0 mm “3225” for 3.2 X 2.5 mm “5032” for 5.0 X 3.2 mm “7050” for 7.0 X 5.0 mm “S” Standard EXAMPLE: LPO 33-2520-20-W-1000kHz-T-S PLEASE INDICATE YOUR REQUIRED PARAMETERS SAMPLES ARE AVAILABLE WITHIN A SHORT DELIVERY PERIOD! CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 5 OF 6 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com PREMIUM QUALITY BY PETERMANN-TECHNIK OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH. THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS. © PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 6 OF 6 I SPEC 01 I REV.00 I NOVEMBER 2014