PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com STRATUM-3 OSCILLATOR 1—60 MHz SERIES „ST3XO“ FEATURES APPLICATIONS + + + + + + + + + + + + + + + + + 100% pin-to-pin drop-in replacement to quartz-based XO Low Power Stratum-3 Oscillator for Low Cost Excellent long time reliability - outperforms quartz-based XO ±4.6 PPM total frequency stability over 20 years <±0.37 PPM (370 ppb) 24-hour hold-over stability ±0.1 PPM (100 ppb) over-temperature stability (0 - 70°C). Excellent phase jitter: 0.5 ps (12 kHz to 20 MHz) Voltage control with ±12.5 PPM pulling range LVCMOS/HCMOS compatible output Pb-free, RoHS and REACH compliant / MSL1 @ 260°C SONET and Synchronous Ethernet based core and edge routers Wireless Base Stations WiMAX IP Timing Test Equipment and Instrumentation Smart Grid etc. GENERAL DATA PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT CONDITION f 1 – 60 MHz Overall Stability F_stab -4.6 – +4.6 PPM Inclusive of temperature, 20 year aging, supply voltage and output load Stability over temperature F_temp -0.10 – +0.10 PPM 0 to 70 °C (Ordering code: Q) -0.20 – +0.20 PPM 0 to 70 °C (Ordering code: P) FREQUENCY RANGE Output Frequency Range FREQUENCY STABILITY Supply Voltage F_vdd –0.025 – +0.025 PPM ±5% VDD Output Load F_load –0.005 – +0.005 PPM ±10% of 15 pF load 24 hour hold-over stabilty F_hold -0.37 – +0.37 PPM Inclusive of temperature, 24 hour aging, supply voltage and output load Initial Tolerance F_init -1 – 1 PPM at 25°C Operating Temperature Range T_use 0 – +70 °C Commercial. Contact Petermann-Technik for extended commercial (-20 to 70 °C) or industrial temperature (-40 to 85°C) range support Storage Temperature Range T_stor -55 – +125 °C Storage Supply Voltage VDD 2.25 2.5 2.75 V Any supply voltage between 2.5V and 3.3V is supported to 1 decimal of accuracy 3.3 3.63 Pull Range PR Control Voltage VC 10 Linearity Lin – OPERATING TEMPERATURE RANGE SUPPLY VOLTAGE AND CURRENT CONSUMPTION 2.97 Frequency Change Polarity Control Voltage -3dB Bandwidth Current Consumption ±12.5 – V PPM – 90 %VDD – 1 % Positive slope – V_BW – – 8 kHz IDD – 31 33 mA CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS No load condition, f = 20 MHz, VDD = 2.5 V or 3.3 V PAGE 1 OF 5 I SPEC 01 I REV.00 I OKTOBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com GENERAL DATA (continued) SYMBOL MIN. TYP. MAX. UNIT DC 45 – 55 % All VDDs. Rise/Fall Time Tr, Tf – 1.5 2 ns 15 pF load, 10% - 90% Vdd Output Voltage High VOH 90% – – VDD IOH = 7mA, VDD = 3.3V IOH = 4.5mA, VDD = 2.5V Output Voltage Low VOL – – 10% VDD IOL = 7mA, VDD = 3.3V IOL = 4.5mA, VDD = 2.5V Output Load Load – – 15 pF At maximum frequency and supply voltage. Contact PetermannTechnik for higher output load options T_start – – 10 ms Measured from the time VDD reaches its rated minimum value RMS Period Jitter T_jitt – 1.7 2.5 ps f = 10 MHz, all VDDs RMS Phase Jitter (random) T_phj – 0.5 – ps f = 10 MHz, Integration bandwidth = 12 kHz to 20MHz, All VDDs PARAMETER AND CONDITIONS CONDITION LVCMOS OUTPUT CHARACTERISTICS Duty Cycle STARTUP TIMING Startup Time JITTER EXCELLENT RELIABILITY DATA MTBF 500 million hours Shock Resistance 10.000 g Vibration Resistance 70 g CONTACT PETERMANN-TECHNIK FOR FOLLOWING OPTIONS: + Programmable rise/fall time control + Fixed frequency TCXO options + Extended commercial and industrial temperature range options + 2.5x2.0mm footprint compatible housing support PHASE NOISE PLOT(1) PIN DESCRIPTION TABLES FIGURE 1. PHASE NOISE, 10MHZ CARRIER, 3.3V, LVCMOS OUTPUT, TCXO TABLE 1 & 2. PIN MAP AND PIN #1 FUNCTIONALITY Phase Noise (dBc/Hz) PIN MAP PIN CONNECTION 1 VC 2 GND 3 CLK 4 VDD PIN # 1 FUNCTIONALITY VIN 0 - VDD: produces voltage dependent frequency change Frequency Offset (Hz) Note: 1. The maximum offset frequency is half of the clock (or carrier) frequency for a digital clock. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 2 OF 5 I SPEC 01 I REV.00 I OKTOBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 3.2 X 2.5 X 0.75 MM #1 2.2 2.1 #3 #3 #1 #2 #2 1.2 0.9 1.9 #4 0.7 3.2±0.15 2.5±0.15 #4 1.4 0.75±0.05 0.9 RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 5.0 X 3.2 X 0.75 MM #1 2.54 2.39 #3 #3 #1 #2 #2 1.6 0.8 2.2 #4 1.1 5.0±0.15 3.2±0.15 #4 1.5 0.75±0.05 1.15 RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 7.0 X 5.0 X 0.90 MM #3 #1 #2 #2 1.1 2.0 3.81 #4 1.4 2.2 0.90±0.10 #1 5.08 5.08 #3 2.6 7.0±0.15 5.0±0.15 #4 CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 3 OF 5 I SPEC 01 I REV.00 I OKTOBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com ORDERING INFORMATION SUPPLY VOLTAGE OSCILLATOR FAMILY “25“ for 2.5V “33“ for 3.3V ST3XO TEMPERATURE RANGE “C” for 0 +70°C FREQUENCY PULL RANGE OPTIONS 1.000000 to 60.000000 MHz ST3XO 33-3225-V-01-C-25.000MHz-T-S-Q FREQUENCY STABILITY “01” for ±0.1 PPM “02” for ±0.2 PPM FEATURE PIN (PIN1) PACKAGE SIZE “V” for VOLTAGE CONTROL “3225” for 3.2 X 2.5 mm “5032” for 5.0 X 3.2 mm “7050” for 7.0 X 5.0 mm PACKING METHOD “B” for BULKS or TUBES “T” for TAPE & REEL OUTPUT DRIVE STRENGTH “S” Standard EXAMPLE: ST3XO-33-3225-V-01-C-25.000MHZ-T-S-Q PLEASE INDICATE YOUR REQUIRED PARAMETERS REFLOW SOLDER PROFILE SAMPLES ARE AVAILABLE WITHIN A SHORT DELIVERY PERIOD! CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 4 OF 5 I SPEC 01 I REV.00 I OKTOBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com PREMIUM QUALITY BY PETERMANN-TECHNIK OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH. THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS. © PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 5 OF 5 I SPEC 01 I REV.00 I OKTOBER 2014