Download

Product Brief 2SP0115T
SCALE-2® Plug-and-Play IGBT-Driver
2SP0115T - Dual-Channel Driver
with electrical interface for 17mm EconoDUALTM IGBT Modules
PRODUCT DESCRIPTION
The 2SP0115T is a dual-channel driver with
an electrical interface. The driver is based
on CONCEPT’s SCALE-2® chipset, a highly
integrated technology for the reliable driving
and safe operation of IGBTs.
circuit protection, advanced active clamping
and supply-voltage monitoring.
Perfectly matched driver versions are available for all 17mm dual IGBT modules. The
plug-and-play capability of the driver allows
immediate operation after mounting. The
user needs invest no effort in designing or
adjusting it to a specific application.
Perfectly matched driver versions are
available for all 17mm dual IGBT modules.
Users need only solder them onto the
corresponding IGBT module. The plug-andplay capability of the driver allows immediate
operation with no further development or
matching effort. Shortest design cycles are
achieved without compromising overall
system efficiency in any way.
2SP0115T is the ultimate low-cost ultracompact driver platform for EconoDUALTM
IGBT modules. As a member of the CONCEPT
plug-and-play driver family, it satisfies the
requirements for optimized electrical performance and noise immunity.
The embedded paralleling capability allows
easy inverter design covering higher power
ratings. Specifically adapted drivers are
available for all module types. The DIC20
electrical interface is very simple and easy
to use.
The highly integrated SCALE-2® chipset
reduces the component count by 80% compared to conventional solutions, thus significantly increasing reliability and reducing
costs.
Thanks to SCALE-2® technology, the
2SP0115T family comprises complete and
extremely compact two-channel IGBT drivers
equipped with DC/DC converters, short-
APPLICATIONS
- Wind-power converters
- Industrial drives
- Railways auxiliary systems
- Induction heating
- Elevators
- UPS and SMPS
- Medical (MRT, CT, X-Ray)
- Laser technology
1/2 Product Brief 2SP0115T – © 2013 CT-Concept Technologie AG
KEY BENEFIT
Compact driver solution for 17mm dual IGBT
modules with an electrical interface for 2-level,
3-level and multilevel converter topologies with
paralleling capability.
KEY FEATURES
- Very short delay time of <100ns
- Small jitter of ±4ns
- +15V (regulated)/-8V gate driving
- Separate gate current paths (on/off)
- Suitable for IGBTs up to 1700V
- Interface for 3.3V...15V logic level
- Direct and half-bridge modes
- Embedded paralleling capability
- 2-level and multilevel topologies
- IGBT short-circuit protection
- Advanced active clamping
- Isolated DC/DC converter
- 2 x 1W output power
- Supply under-voltage lockout
- Safe isolation to EN50178
- UL compliant
- Superior EMC
- Reliable, long service life
Driving Parallel-Connected IGBTs
The driver allows direct parallel connection of
any number of 17mm modules with individual
drivers. This new pioneering concept for simple
and reliable parallel connection makes it practical
for the first time to set up converter series with
discrete modules as well as parallel-connected
IGBTs without any additional development effort.
KEY DATA OVERVIEW
Electrical Interface DIC20
The 2SP0115T driver series is equipped with
DIC20 electrical interface, fully compatible to
PrimePACKTM driver series 2SP0320T. The DIC20
electrical interface is very simple and easy to
use.
The driver has the following terminals:
- Power supply and GND terminals
- 2x drive signal inputs
- 2x status outputs (failure returns)
- 1x mode selection (half-bridge mode/direct mode)
- 1x input to set the blocking time
All inputs are ESD-protected and all digital inputs
have Schmitt-trigger characteristics.
1)
Parameter
Nominal supply voltage
Supply current @ fIN=0Hz
Supply current, full load
Output power per channel
Gate voltage
Peak output current (gate current)
Switching frequency fIN 1)
Duty cycle
Turn-on delay
Turn-off delay
Creepage distance primary-secondary
Creepage secondary-secondary
Clearance distance primary-secondary
Clearance distance secondary-secondary
Dielectric test voltage (600V/1200V versions)
Dielectric test voltage (1700V versions)
Partial discharge extinction voltage (600/1200V versions)
Partial discharge extinction voltage (1700V versions)
dv/dt immunity, input to output
Operating temperature 2SP0115T2Ax-xx
Operating temperature 2SP0115T2Bx-xx
Min
Typical
15
33
-8
0
0
1
+15/-8
12.6
6.6
12.3
6.6
3800
5000
1200
1700
-20
-40
Maximum switching frequency depends on the IGBT gate charge.
See data sheet for actual value of specific driver.
75
65
50
Max
220
+15
50
100
+85
+85
Unit
V
mA
mA
W
V
A
kHz
%
ns
ns
mm
mm
mm
mm
VAC
VAC
Vpeak
Vpeak
kV/us
°C
°C
BASIC SCHEMATIC OF THE 2SP0115T
Vce
Monitoring
Dz
Advanced
Active Clamping
+15V
Rg,on
Q2
T urn-on Driver
Rg,off
Channel 2
The driver contains all necessary components for optimal and safe driving of the relevant IGBT module:
smallest gate resistors in order to minimize switching
losses, gate clamping, active-clamping diodes (overvoltage protection at turn-off), Vce monitoring (shortcircuit protection) as well as the input electrical
connector X1. Moreover, it includes components for
setting the turn-off trip level, the response time and
the dead time between both channels in half-bridge
mode. Its plug-and-play capability means that it is
ready to operate immediately after mounting. The
user needs to invest no effort in designing or adjusting
the driver to a specific application.
T urn-off Driver
Electrical
Interface X1
Vce
Monitoring
Dz
Advanced
Active Clamping
+15V
Rg,on
Q1
T urn-on Driver
Rg,off
Channel 1
T urn-off Driver
Interface X2
NTC
ORDERING INFORMATION 2SP0115T DUAL-CHANNEL SCALE-2 PLUG-AND-PLAY DRIVER
2SP0115T
Type Designation
2SP0115T2A0
2SP0115T2B0
2SP0115T2Ax-xx or
2SP0115T2Bx-xx
Gate resistors have to be soldered by customer
(-20°C…85°C)
(-40°C…85°C)
xx: voltage basic type (for any module type)1)
600V=06 / 1200V=12 / 1700V=17
xx: specific module type (Infineon, Fuji, Mitsubishi, Starpower, Powerex)
such as 2MBI300VN-120-50
2SP0115T
1)
Description
Standard version
Extended operating temperature
CT-Concept Technologie AG
2504 Biel | Switzerland
Phone +41 32 344 47 47
E-mail [email protected]
59469 Ense | Germany
+49 2938 643 9990
[email protected]
2/2 Product Brief 2SP0115T – © 2013 CT-Concept Technologie AG
Naples | FL USA 34101-9799
+1 239 249 9254
[email protected]
518054 Shenzhen | China
+86 755 8663 6456
[email protected]
Bangalore | India 560037
+91 9990 455 666
[email protected]
www.IGBT-Driver.com