2SP0115T SCALE™-2 Plug-and-Play IGBT Driver 2SP0115T Dual-Channel Gate Driver with Electrical Interface for 17 mm-Dual IGBT Modules. PrODUCT DESCrIPTIOn The 2SP0115T is a dual-channel driver with an electrical interface. The driver is based on Power Integrations SCALE™-2 chipset, a highly integrated technology for the reliable driving and safe operation of IGBTs. circuit protection, advanced active clamping and supply-voltage monitoring. Perfectly matched driver versions are available for all 17 mm dual IGBT modules. The plug-and-play capability of the driver allows immediate operation after mounting. The user needs invest no effort in designing or adjusting it to a specific application. Perfectly matched driver versions are available for all 17 mm dual IGBT modules. Users need only solder them onto the corresponding IGBT module. The plug-andplay capability of the driver allows immediate operation with no further development or matching effort. Shortest design cycles are achieved without compromising overall system efficiency in any way. 2SP0115T is the ultimate low-cost ultracompact driver platform for EconoDUAL™ IGBT modules. As a member of the Power Integrations' plug-and-play driver family, it satisfies the requirements for optimized electrical performance and noise immunity. The embedded paralleling capability allows easy inverter design covering higher power ratings. Specifically adapted drivers are available for all module types. The DIC20 electrical interface is very simple and easy to use. The highly integrated SCALE™-2 chipset reduces the component count by 80 % compared to conventional solutions, thus significantly increasing reliability and reducing costs. Thanks to SCALE™-2 technology, the 2SP0115T family comprises complete and extremely compact two-channel IGBT drivers equipped with DC/DC converters, shortPage 26 APPLICATIOnS - Wind-power converters - Industrial drives - railways auxiliary systems - Induction heating - Elevators - UPS and SMPS - Medical (MrT, CT, X-ray) - Laser technology KEy BEnEFIT Compact driver solution for 17 mm dual IGBT modules with an electrical interface for 2-level, 3-level and multilevel converter topologies with paralleling capability. KEy FEATUrES - very short delay time of <100 ns - Small jitter of ±4 ns - +15 v (regulated)/-8 v gate driving - Separate gate current paths (on/off) - Suitable for IGBTs up to 1700 v - Interface for 3.3 v…15 v logic level - Direct and half-bridge modes - Embedded paralleling capability - 2-level and multilevel topologies - IGBT short-circuit protection - Advanced active clamping - Isolated DC/DC converter - 2 x 1 W output power - Supply under-voltage lockout - Safe isolation to En50178 - UL compliant - Superior EMC - reliable, long service life © 2015 | www.power.com/igbt-driver DrIvInG PArALLEL-COnnECTED IGBTS KEy DATA OvErvIEW The driver allows direct parallel connection of any number of 17 mm modules with individual drivers. This new pioneering concept for simple and reliable parallel connection makes it practical for the first time to set up converter series with discrete modules as well as parallel-connected IGBTs without any additional development effort. ELECTrICAL InTErFACE DIC20 The 2SP0115T driver series is equipped with DIC20 electrical interface, fully compatible to PrimePACK™ driver series 2SP0320T. The DIC20 electrical interface is very simple and easy to use. The driver has the following terminals: - Power supply and GnD terminals - 2x drive signal inputs - 2x status outputs (failure returns) - 1x mode selection (half-bridge mode/direct mode) - 1x input to set the blocking time All inputs are ESD-protected and all digital inputs have Schmitt-trigger characteristics. 1) Parameter nominal supply voltage Supply current @ fIn=0 hz Supply current, full load Output power per channel Gate voltage Peak output current (gate current) Switching frequency fIn 1) Duty cycle Turn-on delay Turn-off delay Creepage distance primary-secondary Creepage secondary-secondary Clearance distance primary-secondary Clearance distance secondary-secondary Dielectric test voltage (600 v/1200 v versions) Dielectric test voltage (1700 v versions) Partial discharge extinction voltage (600/1200 v versions) Partial discharge extinction voltage (1700 v versions) dv/dt immunity, input to output Operating temperature 2SP0115T2Ax-xx Operating temperature 2SP0115T2Bx-xx Maximum switching frequency depends on the IGBT gate charge. See data sheet for actual value of specific driver. Min -8 0 0 12.6 6.6 12.3 6.6 3800 5000 1200 1700 -20 -40 Typical 15 33 1 +15/-8 75 65 50 Max 220 +15 50 100 +85 +85 Unit v mA mA W v A khz % ns ns mm mm mm mm vAC vAC vpeak vpeak kv/us degC degC BASIC SChEMATIC OF ThE 2SP0115T The driver contains all necessary components for optimal and safe driving of the relevant IGBT module: smallest gate resistors in order to minimize switching losses, gate clamping, active-clamping diodes (overvoltage protection at turn-off), vce monitoring (short-circuit protection) as well as the input electrical connector X1. Moreover, it includes components for setting the turn-off trip level, the response time and the dead time between both channels in half-bridge mode. Its plug-and-play capability means that it is ready to operate immediately after mounting. The user needs to invest no effort in designing or adjusting the driver for a specific application. OrDErInG InFOrMATIOn 2SP0115T DUAL-ChAnnEL SCALE™-2 PLUG-AnD-PLAy DrIvEr 2SP0115T 1) Type Designation 2SP0115T2A0 2SP0115T2B0 (-20…85 degC) (-40…85 degC) 2SP0115T2A0-xx or 2SP0115T2B0-xx xx: voltage basic type (for any module type)1) xx = 06 (600 v) / xx = 12 (1200 v) / xx = 17 (1700 v) 2SP0115T2C0-xx xx: voltage basic type xx = 06 (600 v) / xx = 12 (1200 v) / xx = 17 (1700 v) 15 v logic level, extended operating temperature (-40…85 degC) Gate resistors have to be soldered by customer © 2015 | www.power.com/igbt-driver Description Standard version Extended operating temperature xx: specific module type (Infineon, Fuji, Mitsubishi, Starpower, Powerex) such as 2MBI300vn-120-50 Page 27