ATK0000CE44

Light Touch Switches/EVPAY
3.4 mm×2.9 mm SMD Light Touch Switches
Type:
EVPAY
■ Features
● External dimensions: 3.4 mm×2.9 mm, Height 0.7 mm
● High operability
Equipped with an actuator (push plate)
● IP67 characteristic
■ Recommended Applications
● Operation switches for portable electronic equipment
(Mobile phone, Portable audio)
■ Explanation of Part Numbers
1
2
3
4
5
&
7
1
"
:
Product Code
Type
6
7
8
9
Height
■ Specifications
Type
Snap action/Push-on type SPST
Rating
Contact Resistance
Electrical
Insulation Resistance
Dielectric Withstanding Voltage
Bouncing
Mechanical
Endurance
IP67(✽1)
Operating Force
Travel
Operating Life
500 mΩ max.
50 MΩ min. (at 100 Vdc)
250 Vac for 1 minute
10 ms max. (ON, OFF)
1.6 N, 2.4 N
0.15 mm
500000 cycles min.
IP6x (Dust resistance)
Dust : Talc (Type4) 8h
IPx7 (Water resistance)
Immersion depth : 1m 30min.
Operating Temperature
Storage Temperature
Minimum Quantity/Packing Unit
Quantity/Carton
10 μA 2 Vdc to 20 mA 15 Vdc (Resistive load)
–40 °C to +85 °C
–40 °C to +85 °C (Bulk)
–20 °C to +60 °C (Taping)
8000 pcs. Embossed Taping (Reel Pack)
40000 pcs.
Note: Non washable
(✽1) IP67 : Switch shall not be operated during test.
Water or dust ingress shall be limited enough to prevent deleterious effect to the switch function.
However, IP67 shall be guaranteed under single product state,
then there is a possibility that IP67 performance become impaired depending on your mounting condition or usage.
So, please ask us in advance, if the switch is applied to important usage for water and dust resistant.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Apr. 2015
Light Touch Switches/EVPAY
■ Dimensions in mm (not to scale)
No. 1
Spacer
film
A'
2-1
A
B
2-1.8
2.9
4-0.5
Movable
contactor
B'
0.015±0.015
B'
A
B
(1.15)
(0.8)
A'
B'
PWB land pattern for reference
=Part of A-A' terminal is exposed at
Any land pattern or vias
shall not be provided at
area.
(1.5)
(2-2.5)
area.
Operating Force
Height
Operating Life
1.6 N
0.7 mm
500000 cycles
EVPAYF1BA
No. 2
B
No soldering
(0.4)
Part Numbers
A'
2-3.5±0.05
2-2.4±0.05
1.6
(0.65)
2-3.4
(Terminal)
A
Circuit diagram
4-0.3
f0.65
(Push-plate)
(f0.75)
(Adhesive)
0.7
0.45
2-1.2±0.05
2-2.4±0.05
3.4
2-3
(Embossed Taping)
2.6
EVPAY
(without the remainder of the gate)
General dimension tolerance : ± 0.1
( )dimensions are reference dimensions.
A'
2-1
B
B'
B
B'
A
No soldering
B
A'
B'
PWB land pattern for reference
(1.15)
(0.8)
(0.4)
A'
2-3.5±0.05
2-2.4±0.05
1.6
(0.65)
0.015±0.015
2-3.4
(Terminal)
A
Circuit diagram
4-0.3
f0.65
(Push-plate)
(f0.75)
(Adhesive)
0.7
0.45
2.6
A
2-1.8
2.9
4-0.5
Movable
contactor
2-1.2±0.05
2-2.4±0.05
3.4
2-3
(Embossed Taping)
(without the remainder of the gate)
General dimension tolerance : ± 0.1
( )dimensions are reference dimensions.
EVPAY
=Part of A-A' terminal is exposed at
Any land pattern or vias
shall not be provided at
area.
(1.5)
(2-2.5)
area.
Part Numbers
Operating Force
Height
Operating Life
EVPAYG0BA
2.4 N
0.7 mm
500000 cycles
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Apr. 2015
Light Touch Switches/EVPAY
■ Recommended Reflow Soldering Conditions
Operation Top (°C)
MAX.
260
Fan or Normal Temp.
230
180
150
(Normal Temp.)
90±30
40±10
Soldering Time (s)
✽ Reflow temperature may vary by location even in the same reflow condition.
Please check the reflow temperature at terminals and at the top of a switch
to make sure the both temperatures are withiin the specification.
If even one of them is out of the specifications, please adjust.
● Embossed Carrier Taping
Tape width=12.0 mm
Chip pocket
E
F
J
I
A
K
C
H
D
fG
B
Feeding hole
B’
B
A’
A
t
Tape running direction
Taping condition : Lack of products in the middle of taping should be
one MAX, but total quantity specified in the
specifications should be secured.
Peeling off strength of top tape : It should be within 0.2N to 1. ON at
165 degree in peeling off angle.
Joint of carrier tape : One joint per one reel may exist.
Unit: mm
Part No.
Height
EVPAY
0.7
A
B
C
12.0±0.3 1.75±0.10 5.5±0.1
D
E
F
8.0±0.1
4.0±0.1
2.0±0.1
G
H
I
1.5±0.3 3.15±0.20 3.7±0.2
J
K
t
0.8±0.2
(10.25)
0.3±0.1
● Standard Reel Dimensions in mm (not to scale)
G
E
Item
C
A
B
D
E
013.0±0.5
021.0±1.0
2.0±0.5
B
Rate (mm) 0380.0±2.0 080.0±1.0
C
D
A
Item
F
G
Rate (mm)
13.5±1.0
17.5±1.0
F
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Apr. 2015