Catalogs/Datasheets

EW
N
Light Touch Switches/EVPBA
3.0mm×2.6mm 2 terminals SMD
Light Touch Switches
Type:
EVPBA
■ Features
● External dimensions: 3.0mm×2.6mm, Height 0.58mm
●High operability
Equipped with an actuator (push plate)
■ Recommended Applications
● Operation switches for portable electronic equipment
(Mobile phone, Portable audio)
■ Explanation of Part Numbers
1
2
3
4
5
E
V
P
B
A
Product Code
6
7
8
9
Type
■ Specifications
Type
Snap action / Push-on type SPST
Rating
Contact Resistance
Electrical
Mechanical
Endurance
Insulation Resistance
500mΩ max.
50MΩ min.(at 100V DC)
Dielectric Withstanding Voltage
250V AC for 1 minute
Bouncing
10ms max.(ON, OFF)
Operating Force
Travel
Operating Life
Operating Temperature
Storage Temperature
Minimum Quantity/Packing Unit
Quantity/Carton
10μA 2V DC to 20mA 15V DC(Resistive load)
1.8N
0.13 mm
300,000cycles min.
‒40℃ to +85℃
‒40℃ to +85℃(Bulk)
‒20℃ to +60℃(Taping)
20,000 pcs. Embossed Taping(Reel Pack)
100,000 pcs.
Note: Non washable
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Oct. 2015
■ Dimensions in mm(not to scale)
EVPBA
(Embossed Taping)
General dimension tolerance : ± 0.1
( )
dimensions are reference dimensions.
3.5
3
1.3
2.6
(Without the remainder of the gate)
This reference specifications are subject to change.
A'
A
(φ0.7)
(Push plate)
A
A'
(0.04)
0.35
0.38
0.58
Circuit diagram
A
A'
2-1.5
3.8
2.6
Land pattern plan
Soldering thickness t=0.08±0.01
The opening ratio of the solder stencil to a
land pattern shall be 70%
If you design different stencil mask and land
pattern, or apply different soldering thickness
compared with our recommended pattern as
described above, please ask us in advance.
Part Numbers
Operating Force
Height
Operating Life
EVPBABA3A
1.8N
0.58mm
300,000cycles
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Oct. 2015
EW
N
Light Touch Switches/EVPBA
EW
N
Light Touch Switches/EVPBA
■ Recommended Reflow Soldering Conditions
Operation Top(℃)
MAX.
260
Fan or Normal Temp.
230
180
150
(Normal Temp.)
90±30
40±10
Soldering Time
(S)
* Reflow temperature may vary by location even in the same reflow condition.
Please check the reflow temperature at terminals and at the top of a switch
to make sure the both temperatures are withiin the specification.
If even one of them is out of the specifications, please adjust.
● Embossed Carrier Taping
Tape width=12.0 mm
I
øG
F
E
J
B
D
H
K
A
C
Taping condition:Lack of products in the middle of taping should
be one MAX, but total quantity specified in
the specifications should be secured.
Peeling off strength of top tape:It should be within 0. 2N to
1.0N at 165 degree in peeling
off angle.
Joint of carrier tape:One joint per one reel may exist.
t
Take out direction
Unit:mm
Part No.
Height
EVPBA
0.58
A
B
C
12.0±0.3 1.75±0.10 5.5±0.1
D
E
F
G
H
4.0±0.1
4.0±0.1
2.0±0.1
1.5±0.3
Item
A
I
J
K
t
3.75±0.20 2.85±0.20 0.8±0.2 (10.25) 0.3
+0.15
- 0.1
● Standard Reel Dimensions in mm(not to scale)
G
E
C
B
C
D
2.0±0.5
B
Rate(mm)ø380.0±2.0 ø80.0±1.0 ø13.0±0.5 ø21.0±1.0
E
Item
D
A
F
Rate(mm) 13.5±1.0
G
17.5±1.0
F
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Oct. 2015