ATV0000CE19

EW
N
Light Touch Switches/EVPBD
6mm Square Middle Travel 2 terminals SMD
Light Touch Switches
Type:
EVPBD
■ Features
● External dimensions: 6.0mm×6.0mm, Height 4.0mm
● Sharp feeling and silent by metal dome and rubber dome
■ Recommended Applications
● Operating switches for car electronic equipment,
car audio systems, etc.
● Steering switches
■ Explanation of Part Numbers
1
2
3
4
5
E
V
P
B
D
Product Code
Type
6
7
8
9
10
（11）
（12）
Operating Force
■ Specifications
Type
Snap action / Push-on type SPST
Rating
Contact Resistance
Electrical
Mechanical
Endurance
Insulation Resistance
500mΩ max.
100MΩ min.（at 100V DC）
Dielectric Withstanding Voltage
250V AC for 1 minute
Bouncing
10ms max.（ON, OFF）
Operating Force
Travel
Operating Life
Operating Temperature
Storage Temperature
Minimum Quantity/Packing Unit
Quantity/Carton
10μA 2V DC to 50mA 12V DC（Resistive load）
3.5N
0.75mm
100,000cycles min.
‒40℃ to +85℃
‒40℃ to +85℃（Bulk）
‒20℃ to +60℃（Taping）
2,000 pcs. Embossed Taping（Reel Pack）
10,000 pcs.
Note: Non washable
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Oct. 2015
■ Dimensions in mm（not to scale）
EVPBD
（Embossed Taping）
General dimension tolerance : ±0.2
（ ）
dimensions are reference dimensions.
4
6±0.1
B
1.4
6±0.1
A
2.5
φ3
1±0.3
A
B
Circuit diagram
7±0.3
8
2- 2
4
Land pattern plan
Soldering thickness t=0.15±0.03
（5）
Part Numbers
Operating Force
Height
Operating Life
EVPBD6C1A000
3.5N
4.0mm
100,000cycles
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Oct. 2015
EW
N
Light Touch Switches/EVPBD
EW
N
Light Touch Switches/EVPBD
■ Recommended Reflow Soldering Conditions
Operation Top（℃）
MAX.
260
Fan or Normal Temp.
230
180
150
（Normal Temp.）
90±30
40±10
Soldering Time
（S）
＊ Reflow temperature may vary by location even in the same reflow condition.
Please check the reflow temperature at terminals and at the top of a switch to
make sure the both temperatures are withiin the specification.
If even one of them is out of the specifications, please adjust.
● Embossed Carrier Taping
Tape width=12.0 mm
D
E
H
B
øG
J
F
I
A
C
Taping condition：Lack of products in the middle of taping should
be one MAX, but total quantity specified in
the specifications should be secured.
Peeling off strength of top tape：It should be within 0. 2N to
1.0N at 165 degree in peeling
off angle.
Joint of carrier tape：One joint per one reel may exist.
t
Take out direction
Unit：mm
Part No.
Height
A
B
C
D
E
F
EVPBD
4.0
12.0±0.3
1.75±0.10
5.5±0.1
8.0±0.1
4.0±0.1
2.0±0.1
G
1.5
+0.1
-0
H
I
J
t
6.3±0.2
7.5±0.2
4.25±0.20
0.4±0.1
B
C
● Standard Reel Dimensions in mm（not to scale）
G
E
Item
C
A
D
2.0±0.5
B
Rate（mm）ø380.0±2.0 ø80.0±1.0 ø13.0±0.5 ø21.0±1.0
E
Item
D
A
F
Rate（mm） 13.5±1.0
G
17.5±1.0
F
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Oct. 2015