EW N Light Touch Switches/EVPAT 3.4mm×1.7mm Side-operational Edge-mount Light Touch Switches Type: EVPAT ■ Features ● External dimensions : 3.4mm×1.7mm (Excluding the push plate), Height 1.6mm (Printed circuit board being as low as 1.105mm) ● High operability Equipped with an actuator (push plate) ● IP67 characteristic ■ Recommended Applications ● Operation switches for portable electronic equipment (Mobile phones, Digital still cameras, Camcorders Portable audio players, etc.) ■ Explanation of Part Numbers 1 2 3 4 5 E V P A T Product Code Type 6 7 8 9 10 （11） （12） Height ■ Specifications Type Snap action / Push-on type SPST Rating Contact Resistance Electrical Mechanical Endurance Insulation Resistance 500mΩ max. 50MΩ min.（at 100V DC） Dielectric Withstanding Voltage 250V AC for 1 minute Bouncing 10ms max.（ON, OFF） Operating Force Travel Operating Life Operating Temperature Storage Temperature Minimum Quantity/Packing Unit Quantity/Carton 10μA 2V DC to 20mA 15V DC（Resistive load） 1.6N 1.6N : 0.11 mm 500,000cycles min. ‒40℃ to +85℃ ‒40℃ to +85℃（Bulk） ‒20℃ to +60℃（Taping） 10,000 pcs. Embossed Taping（Reel Pack） 50,000 pcs. Note: Non washable Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Oct. 2015 ■ Dimensions in mm（not to scale） EVPAT （Embossed Taping） General dimension tolerance : ± 0.1 （ ） dimensions are reference dimensions. This reference specifications are subject to change. Molding Gate 1.105 1.65 C 0.28 2-0.15±0.05 1.73 （1.9） （4.2） 3.4 （Without the remainder of the molding gate） C 0.08±0.05 （φ0.91） （φ0.7） 0.56 1.34 Actuator cross section （Section C-C） B A （2.86） A B Circuit diagram A +0.1 B 3.4±0.05 2.2±0.05 1±0.05 1 0 1.14±0.05 1.4±0.05 1.54±0.05 0.34±0.05 0.84±0.05 0.2±0.05 0.34±0.05 <Back View> Push plate side 2.7±0.05 4.6±0.05 Edge of PCB Land pattern plan Soldering thickness t=0.12±0.02 Part Numbers Operating Force Height Operating Life EVPAT2G1B000 1.6N 1.105mm 500,000cycles Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Oct. 2015 EW N Light Touch Switches/EVPAT EW N Light Touch Switches/EVPAT ■ Recommended Reflow Soldering Conditions Operation Top（℃） MAX. 260 Fan or Normal Temp. 230 180 150 （Normal Temp.） 90±30 40±10 Soldering Time （S） ＊ Reflow temperature may vary by location even in the same reflow condition. Please check the reflow temperature at terminals and at the top of a switch to make sure the both temperatures are withiin the specification. If even one of them is out of the specifications, please adjust. ● Embossed Carrier Taping Tape width=12.0 mm B F K L H Taping condition：Lack of products in the middle of taping should be one MAX, but total quantity specified in the specifications should be secured. Peeling off strength of top tape：It should be within 0. 2N to 1.0N at 165 degree in peeling off angle. Joint of carrier tape：One joint per one reel may exist. I A M C E .5 ø1 D t J Take out direction Unit：mm Part No. Height EVPAT 1.105 A B C D E F 12.0±0.2 1.75±0.1 5.5±0.05 4.0±0.1 4.0±0.1 2.0±0.05 1.5 G H +0.1 -0 I 2.28±0.2 4.8±0.2 J K L M t (1.065) 1.23±0.1 0.77±0.1 (10.25) 0.3±0.05 ● Standard Reel Dimensions in mm（not to scale） G E Item A B C D E C 2.0±0.5 B Rate（mm）ø380.0±2.0 ø80.0±1.0 ø13.0±0.2 ø21.0±0.8 Item D A F Rate（mm） 13.4±1.0 G 17.4±1.0 F Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Oct. 2015