Light Touch Switches/EVPAK 3.8 mm×1.9 mm Side-operational SMD Light Touch Switches Type: EVPAK ■ Features ● External dimensions: 3.9 mm×2.05 mm, (Excluding the push plate) Height 1.6 mm ● Side-operational type ● Good feeling ● Measure against electro static discharge (ESD) ● IP67 characteristic ■ Recommended Applications ● Operation switches for portable electronic equipment (Mobile phone, Portable audio) ■ Explanation of Part Numbers 1 2 3 4 5 & 7 1 " , Product Code Type 6 7 8 9 Height ■ Specifications Type Snap action/Push-on type SPST Rating Contact Resistance Electrical Insulation Resistance Dielectric Withstanding Voltage Bouncing Mechanical Endurance IP67(✽1) Operating Force Travel Operating Life 100 mΩ max. 100 MΩ min. (at 100 Vdc) 250 Vac for 1 minute 10 ms max. (ON, OFF) 1.6 N 0.12 mm 200000 cycles min. IP6x (Dust resistance) Dust : Talc (Type4) 8h IPx7 (Water resistance) Immersion depth : 1m 30min. Operating Temperature Storage Temperature Minimum Quantity/Packing Unit Quantity/Carton 10 μA 2 Vdc to 20 mA 15 Vdc (Resistive load) –40 °C to +85 °C –40 °C to +90 °C (Bulk) –20 °C to +60 °C (Taping) 5000 pcs. Embossed Taping (Reel Pack) 25000 pcs. Note: Non washable (✽1) IP67 : Switch shall not be operated during test. Water or dust ingress shall be limited enough to prevent deleterious effect to the switch function. However, IP67 shall be guaranteed under single product state, then there is a possibility that IP67 performance become impaired depending on your mounting condition or usage. So, please ask us in advance, if the switch is applied to important usage for water and dust resistant. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Jul. 2014 Light Touch Switches/EVPAK ■ Dimensions in mm (not to scale) EVPAK (Embossed Taping) General dimension tolerance : ± 0.1 ( )dimensions are reference dimensions. 2.9 (2.05) 0.85 0.8 0.20±0.05 0.40±0.05 This reference specifications are subject to change. 0.80±0.05 1.5 3.9 3.2 (2.2) 1.10±0.05 A 0.43±0.04 0.3±0.2 0.45 0.9 1.60±0.08 0.40±0.05 A' (1.4) 1.50±0.07 0.4 A A 3.7±0.1 2.3 2-0.65 A' A' 1.15 0.7 2.1 1.4 2-R 0.7 1.1 1.15 0.95 0.95 2-f0.55+0.1 0 Circuit diagram 2-1.1 0.8 PWB land pattern for reference Soldering thickness t=0.10 to 0.12 Part Numbers EVPAKB11A Operating Force Height Operating Life 1.6 N 1.6 mm 200000 cycles Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Jul. 2014 Light Touch Switches/EVPAK ■ Recommended Reflow Soldering Conditions Operation Top (°C) MAX. 260 Fan or Normal Temp. 230 180 150 (Normal Temp.) 90±30 40±10 Soldering Time (s) ✽ Reflow temperature may vary by location even in the same reflow condition. Please check the reflow temperature at terminals and at the top of a switch to make sure the both temperatures are withiin the specification. If even one of them is out of the specifications, please adjust. ● Embossed Carrier Taping Tape width=12.0 mm Chip pocket E F K H L A M C H D fG B Feeding hole J t Tape running direction Taping condition : Lack of products in the middle of taping should be one MAX, but total quantity specified in the specifications should be secured. Peeling off strength of top tape : It should be within 0.2N to 1. ON at 165 degree in peeling off angle. Joint of carrier tape : One joint per one reel may exist. Unit: mm Part No. Height EVPAK 1.6 A B C D E F 12.0±0.2 1.75±0.10 5.50±0.05 8.0±0.1 4.0±0.1 2.00±0.05 G H 1.5+0.1 0 I 3.15±0.20 4.1±0.2 J (1.125) K L K t 1.8±0.1 0.65±0.10 (10.25) 0.30±0.05 ● Standard Reel Dimensions in mm (not to scale) G E Item C A B D E 013.0±0.5 021.0±1.0 2.0±0.5 B Rate (mm) 0380.0±2.0 080.0±1.0 C D A Item F G Rate (mm) 13.5±1.0 17.5±1.0 F Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Jul. 2014