EW N Light Touch Switches/EVPBD 6mm Square Middle Travel 2 terminals SMD Light Touch Switches Type: EVPBD ■ Features ● External dimensions: 6.0mm×6.0mm, Height 4.0mm ● Sharp feeling and silent by metal dome and rubber dome ■ Recommended Applications ● Operating switches for car electronic equipment, car audio systems, etc. ● Steering switches ■ Explanation of Part Numbers 1 2 3 4 5 E V P B D Product Code Type 6 7 8 9 10 (11) (12) Operating Force ■ Specifications Type Snap action / Push-on type SPST Rating Contact Resistance Electrical Mechanical Endurance Insulation Resistance 500mΩ max. 100MΩ min.(at 100V DC) Dielectric Withstanding Voltage 250V AC for 1 minute Bouncing 10ms max.(ON, OFF) Operating Force Travel Operating Life Operating Temperature Storage Temperature Minimum Quantity/Packing Unit Quantity/Carton 10μA 2V DC to 50mA 12V DC(Resistive load) 3.5N 0.75mm 100,000cycles min. –40℃ to +85℃ –40℃ to +85℃(Bulk) –20℃ to +60℃(Taping) 2,000 pcs. Embossed Taping(Reel Pack) 10,000 pcs. Note: Non washable Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Oct. 2015 N ■ Dimensions in mm(not to scale) EVPBD (Embossed Taping) General dimension tolerance : ±0.2 ( ) dimensions are reference dimensions. 4 6±0.1 B 1.4 6±0.1 A 2.5 φ3 1±0.3 A B Circuit diagram 7±0.3 8 2- 2 4 Land pattern plan Soldering thickness t=0.15±0.03 (5) Part Numbers Operating Force Height Operating Life EVPBD6C1A000 3.5N 4.0mm 100,000cycles Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Oct. 2015 EW Light Touch Switches/EVPBD EW N Light Touch Switches/EVPBD ■ Recommended Reflow Soldering Conditions Operation Top(℃) MAX. 260 Fan or Normal Temp. 230 180 150 (Normal Temp.) 90±30 40±10 Soldering Time (S) *Reflow temperature may vary by location even in the same reflow condition. Please check the reflow temperature at terminals and at the top of a switch to make sure the both temperatures are withiin the specification. If even one of them is out of the specifications, please adjust. ● Embossed Carrier Taping Tape width=12.0 mm D E H øG J ◦Taping condition:Lack of products in the middle of taping should be one MAX, but total quantity specified in the specifications should be secured. ◦Peeling off strength of top tape:It should be within 0. 2N to 1.0N at 165 degree in peeling off angle. ◦Joint of carrier tape:One joint per one reel may exist. I A C B F t Take out direction Unit:mm Part No. Height A B C D E F EVPBD 4.0 12.0±0.3 1.75±0.10 5.5±0.1 8.0±0.1 4.0±0.1 2.0±0.1 G 1.5 +0.1 -0 H I J t 6.3±0.2 7.5±0.2 4.25±0.20 0.4±0.1 B C ● Standard Reel Dimensions in mm(not to scale) G E Item C D B Rate(mm)ø380.0±2.0 ø80.0±1.0 ø13.0±0.5 ø21.0±1.0 D A A Item F Rate(mm) 13.5±1.0 E 2.0±0.5 G 17.5±1.0 F Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Oct. 2015