PB-32HQ MOUNTING BOARD • Input and output modules accepted interchangeably • Operate with 5, 15 or 24 volt logic supplies • Captive-screw retaining system for Quad-Pack • Plug-compatible logic connections • Screw terminal barrier block for load connections • 5 amp field-replaceable fuses modules (LITTLEFUSE #251005 or equivalent) • All even-numbered logic connections are logic ground MECHANICAL SPECIFICATIONS DIMENSIONS: INCHES (MILLIMETERS) TOLERANCE: ±0.020 (±0.50) 11.5 (291,9) 11.0 (279,4) SWAGED STANDOFF THRU HOLE 0.15 (3.8) DIA. x 0.75 (19,1) LONG (4) 0.25 (6,4) 5.5 (139,7) 0.25 (6,4) PWR ON 5A SPARE FUSE 1 2 GND +5V C C 3 4 5 6 C C 7 8 9 10 C C 11 13 12 14 C C 15 17 16 18 C C 19 21 20 22 C C 23 24 25 26 C C 27 28 29 30 C C 31 32 TB1 D2 R1 D1 POWER BARRIER STRIPS (SEE NOTE 2,3) TB3 4-40 SCREW TERMINAL LOGIC SUPPLY BARRIER STRIP REPLACEABLE 2 AMP LOGIC SUPPLY FUSE (SEE NOTE 4) 6.0 (152,4) 6.5 (164,9) F1A J1 J2 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 REPLACEABLE 5 AMP LINE FUSES (16) (SEE NOTE 5) GORDOS QUAD-PACK DIGITAL I/O MODULES SOLD SEPERATELY 0-3 12-15 8-11 4-7 20-23 16-19 J3 50 CONDUCTOR MALE PIN CONNECTORS (J1,J2) (SEE NOTE 1) 3.15 (80,0) 3.9 (100,2) PAM-4 MULTIPLEXER BOARD SOLD SEPERATELY NOTES: 1) CONNECTOR IS CIRCUIT ASSEMBLY CA-50H-2B-SR OR EQUIVALENT. CONNECTORS ARE WIRED IN PARALLEL. 2) 6-32 SCREW TERMINAL BARRIER STRIPS ACCEPT WIRE SIZES FROM 24 TO 12 AWG. 3) OPTIONAL JUMPERS AVAILABLE TO INTERCONNECT BARRIER STRIP COMMONS. ORDER 2 EACH JUMPERS "JQ2" AND 4 EACH JUMPERS "JQ4". 1 LOGIC SUPPLY BARRIER STRIP 1 AMP LOGIC SUPPLY FUSE +5V GND C 2 5 4 C 6 7 C 9 8 C 10 11 C C 14 15 C 17 16 C 18 19 C 21 20 C 22 23 C 25 24 C 26 27 C 29 28 C 30 31 C LOWER BARRIER STRIP 32 8 1 8 1 8 1 8 1 8 1 8 1 8 1 9 2 9 2 9 2 9 2 9 2 9 2 9 2 9 3 10 3 10 3 10 3 10 3 10 3 10 3 10 3 10 11 4 11 4 11 4 11 4 11 4 11 4 11 4 4 CARD SUPPORTS (2) 4) LITTLE FUSE 251001 OR EQUIVALENT. 5) LITTLE FUSE 251005 OR EQUIVALENT. 13 12 28-31 57-462 PB-32HQ HEADER CONNECTOR (J3) 2 1 PWR ON 3 C 24-27 8 UPPER BARRIER STRIP 5 AMP LINE FUSES (16) 11 5 12 5 12 5 12 5 12 5 12 5 12 5 12 5 12 6 13 6 13 6 13 6 13 6 13 6 13 6 13 6 13 7 14 7 14 7 14 7 14 7 14 7 14 7 14 7 14 I/O MODULE PIN SOCKETS 70-PIN MALE CONNECTOR ACCEPTS PAM4 MULTIPLEXER BOARD J1 J2 SIGNAL INPUT/OUTPUT 50 CONDUCTOR MALE PIN CONNECTORS. J1 AND J2 ARE WIRED IN PARALLEL. Rev. 020410 DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / PERIGO HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. • Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION • Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil • Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. • Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen • Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSI ONE. • Spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra • Verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one L'omissione di seguire queste istruz ioni provocherà la morte o di lesioni serie RISCO DE DESCARGA ELÉTTRICA OU EXPLOSÃO • Desconectar o equipamento de toda á energia antes de instalar ou trabalhar com este equipamen to • Verificar todas as conexões e recolocar todas as tampas antes de religar o equipamento O não cumprimento destas instruções pode levar á morte ou lesões sérias. ANNEX - ENVIROMENTAL INFORMATION