PB16 MOUNTING BOARD • All even-numbered logic connections are • Plug-compatible logic connections • Screw terminal barrier block for load connections • Resident pull-up resistors • 5 amp field-replaceable fuses logic ground • Input and output modules accepted interchangeably • Operate with 5, 15 or 24 volt logic supplies • Captive-screw retaining system for standard-size (LITTLEFUSE #251005 or equivalent) modules • LEDs indicate logic status MECHANICAL SPECIFICATIONS 14.1 (356,9) DIMENSIONS: INCHES (MILLIMETERS) TOLERANCE:+-0.020 ( +- 0,50) 7.3 (185,4) 6.25 (158,8) SCREW TERMINAL LOGIC SUPPLY BARRIER STRIP 1 2 3 4 5 6 7 8 POWER BARRIER STRIP (see notes 2,3) 9 10 11 12 13 14 15 16 17 18 19 0.2 (6,4) 20 21 22 23 24 25 26 27 28 29 30 31 32 REPLACEABLE 5 AMP LINE FUSES (16) (see note 4) + 1.4 (35,6) SWAGED STANDOFF THRU HOLE 0.15 (3,2) DIA. (4) 2.6 (66,0) 3.5 (88,9) NYLON STANDOFF 6-32 THD. GORDOS DIGITAL I/O MODULES SOLD SEPERATELY 1.6 (40,6) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PULL UP RESISTOR 3.3K OHM (16) 0.75 (19,1) 0.45 (11,4) 2.2 (55,9) 0.4 (10,2) LED STATUS INDICATOR (16) NOTES: 1) MATING CONNECTOR IS BERG 66317-150 OR EQUIVALENT. SPECIFY SUFFIX 'C' FOR OPTIONAL 65823-093 OR EQUIVALENT MALE PIN CONNECTOR FOR THE PARALLEL-TO-THE-BOARD CABLE CONNECTION. SPECIFY SUFFIX 'V' FOR OPTIONAL CIRCUIT ASSEMBLY CA-50H-2B-SR OR EQUIVALENT MALE PIN CONNECTOR FOR PERPENDICULAR-TO-THE-BOARD CABLE CONNECTION. 2) 6-32 SCREW TERMINAL BARRIER STRIPS ACCEPT WIRE SIZES FROM 24 TO 12 AWG. SIGNAL INPUT/OUTPUT 50 TRACE (0.1" CENTERS) MALE CARD EDGE (see note 1) 3) OPTIONAL JUMPERS ARE AVAILABLE TO INTERCONNECT BARRIER STRIP COMMONS. ORDER 1 EACH "JS2" AND 2 EACH "JS8". 4) LITTLE FUSE 251005 OR EQUIVALENT. POWER BARRIER STRIP LOGIC SUPPLY BARRIER STRIP EDGE CONN + BOTTOM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 5 AMP LINE FUSES (16) LOGIC ALL GND EVEN PINS 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 I/O MODULE PIN SOCKETS TOP +LOGIC SIGNAL INPUT/OUTPUT 50 TRACE (0.1" CENTERS) MALE CARD EDGE OR OPTIONAL PIN CONNECTOR +LOGIC APPROVALS UL E79183 CSA 38595 1 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 PULL UP RESISTOR 3.3K OHM (16) CUSTOMER INSTALLED OPTIONAL JUMPERS TO CONNECT LOGIC SUPPLY TO EDGE CONNECTOR (2) LED STATUS INDICATOR (16) Rev. 070808 DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / PERIGO HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. x Disconnect all power before installing or working with this equipment. x Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. x Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. x Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION x Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil x Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. x Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen x Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSI ONE. x Spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra x Verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one L'omissione di seguire queste istruz ioni provocherà la morte o di lesioni serie RISCO DE DESCARGA ELÉTTRICA OU EXPLOSÃO x Desconectar o equipamento de toda á energia antes de instalar ou trabalhar com este equipamen to x Verificar todas as conexões e recolocar todas as tampas antes de religar o equipamento O não cumprimento destas instruções pode levar á morte ou lesões sérias. ANNEX - ENVIROMENTAL INFORMATION