TVS Diode Arrays (SPA™ Family of Products) Lightning Surge Protection - SP4040 Series SP4040 Series 3.3V 75A Diode Array Pb GREEN RoHS The SP4040 provides overvoltage protection for applications such as 10/100/1000 Base-T Ethernet and T3/ E3 interfaces. This device has a low capacitance of only 5pF making it suitable for PHY side Ethernet protection and the capability to protect against both longitudinal and differential transients. Furthermore, the SP4040 is rated up to 100A (tp=2/10μs) making it suitable for line side protection as well against lightning transients as defined by GR-1089 (intra-building), ITU, YD/T, etc. The application schematic provides the connection information for a PHY side protection scheme of a single differential pair. Pinout Features 1 8 2 7 t$MBNQJOHTQFFEPG nanoseconds t-JHIUOJOHQSPUFDUJPO IEC61000-4-5, 75A (8/20μs) t40*$TVSGBDFNPVOU package (JEDEC MS-012) t-PXDMBNQJOHWPMUBHF 3 6 t-PXJOTFSUJPOMPTTMPH linear capacitance 4 5 t$PNCJOFEMPOHJUVEJOBM and metallic protection t6-7FQPYZNPMEJOH t3P)4DPNQMJBOU SOIC-8 (Top View) Note: Pinout diagrams above shown as device footprint on circuit board. Functional Block Diagram Line in Pin 1 and 8 Applications Line out t5&-JOFDBSET t 5&BOE%4*OUFSGBDFT t #BTF5 Ethernet t 454*OUFSGBDFT Application Example Pin 2, 3, 6, and 7 1 8 2 7 3 6 TeleLink (0461 1.25) to chipset (Ethernet PHY, T3/E3 PHY, etc.) 5 4 Line out Line in SP4040-02BTG Pin 4 and 5 The schematic shows protection for a single differential pair as part of a larger high-speed data interface such as Ethernet. The SP4040 provides both metallic (differential) and longitudinal (common mode) protection from lightning induced surge events as specified by regulatory standards such as Telcordia’s GR-1089 CORE and ITU K.20 and 21. Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. The SP4040 protects against both positive and negative induced surge events while the TeleLink fuse provides overcurrent protection for the long term 50/60 Hz power fault events. ©2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. 151 Revision: March 20, 2012 SP4040 Series SP4040 Description TVS Diode Arrays (SPA™ Family of Products) Lightning Surge Protection - SP4040 Series Parameter Parameter Rating Units 170 °C/W Operating Temperature Range -55 to 125 °C Rating Units Peak Pulse Current (8/20μs) 75 A SOIC Package Peak Pulse Power (8/20μs) 2100 W IEC 61000-4-2, Direct Discharge, (Level 4) 30 kV Storage Temperature Range -65 to 150 °C IEC 61000-4-2, Air Discharge, (Level 4) 30 kV Maximum Junction Temperature 150 °C Telcordia GR 1089 (Intra-Building) (2/10μs) 100 A °C 20 A Maximum Lead Temperature (Soldering 20-40s) (SOIC - Lead Tips Only) 260 ITU K.20 (5/310μs) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Characteristics (TOP = 25°C) Parameter Symbol Test Conditions Min Typ Max Units VRWM IT≤1μA - - 3.3 V Reverse Breakdown Voltage VBR IT= 2μA 3.3 - - V Snap Back Voltage Reverse Stand-Off Voltage VSB IT= 50mA 3.3 - - V Reverse Leakage Current IR VRWM= 3.3V - - 1 μA Clamping Voltage, Line-Ground1 VC IPP= 40A, tp=8/20 μs - - 14 V Clamping Voltage, Line-Ground1 VC IPP= 75A, tp=8/20 μs - - 20 V VC IPP= 100A, tp=2/10 μs 20 V 1 Clamping Voltage, Line-Ground 1 RDYN ( VC2-VC1)/(IPP2-IPP1) - 0.2 - 1 VC IPP= 40A, tp=8/20 μs - - 20 V 1 VC IPP= 75A, tp=8/20 μs - - 30 V VC IPP= 100A, tp=2/10 μs 30 V RDYN ( VC2-VC1)/(IPP2-IPP1) - 0.3 - Line to Ground VR=0V, f= 1MHz - 5 8 pF Line to Line, VR=0V, f= 1MHz - 2.5 5 pF Dynamic Resistance, Line-Ground Clamping Voltage, Line-Line Clamping Voltage, Line-Line 1 Clamping Voltage, Line-Line 1 Dynamic Resistance, Line-Line Junction Capacitance1 1 Cj Parameter is guaranteed by design and/or device characterization. SP4040 Series 152 Revision: March 20, 2012 ©2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. SP4040 Thermal Information Absolute Maximum Ratings TVS Diode Arrays (SPA™ Family of Products) Lightning Surge Protection - SP4040 Series Pulse Waveform Clamping Voltage vs. IPP 30 110% 100% 25 Percent of IPP 80% 70% 60% 50% 40% Line-Line 20 SP4040 Clamp Voltage-VC (V) 90% 15 10 Line-Gound 5 30% 20% 0 10% 0 0% 0.0 5.0 10.0 15.0 20.0 25.0 10 20 30 40 50 60 70 Peak Pulse Current -I PP (A) 30.0 Time (μs) Capacitance vs. Reverse Bias at 1MHz Current Derating Curve 6.0 Percentage of Rated Current (% IP) 120 Line-Gound 5.0 Capacitance (pF) 4.0 3.0 2.0 Line-Line 1.0 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 100 80 60 40 20 0 0 Bias Voltage (V) 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 Ambient Temperature (ºC) Non-Repetitive Peak Pulse Power vs. Pulse Time Peak Pulse Power (kW) 10 1 0.1 1 10 100 1000 Peak Pulse Duraon - tP (μs) ©2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. 153 Revision: March 20, 2012 SP4040 Series TVS Diode Arrays (SPA™ Family of Products) Lightning Surge Protection - SP4040 Series Soldering Parameters Pb – Free assembly tP Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Temperature TP tL Ramp-do Ramp-down Preheat TS(min) tS time to peak temperature 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C Part Marking System CYYWW TL TS(max) 25 Peak Temperature (TP) LF SP4040-02 Critical Zone TL to TP Ramp-up Time Product Characteristics Part number Date code Pin1 Lead Plating Matte Tin plating Lead Material Copper Alloy Lead Coplanarity 0.0004 inches (0.102mm) Substitute Material Silicon Body Material Molded Epoxy Flammability UL 94 V-0 Notes : 1. All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. 4. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 5. Package surface matte finish VDI 11-13. SP4040 Series 154 Revision: March 20, 2012 ©2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. SP4040 Reflow Condition TVS Diode Arrays (SPA™ Family of Products) Lightning Surge Protection - SP4040 Series Package Dimensions — Mechanical Drawings and Recommended Solder Pad Outline Package SOIC Pins 8 JEDEC MS-012 Millimetres o Recommended Soldering Pad Outline (Reference Only) Inches Min Max Min Max A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.004 0.010 A2 1.25 1.65 0.050 0.065 B 0.31 0.51 0.012 0.020 c 0.17 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 5.80 6.20 0.228 0.244 E1 3.80 4.00 0.150 0.157 e 1.27 BSC L 0.050 BSC 1.27 0.40 0.050 0.016 Embossed Carrier Tape & Reel Specification — SOIC Package User Feeding Direction Millimetres E Pin 1 Location Min Max 1.65 1.85 0.065 0.073 F 5.4 5.6 0.213 0.22 1.95 2.05 0.077 0.081 D 1.5 1.6 0.059 0.063 P0 10P0 1.50 Min 3.9 4.1 40.0 +/- 0.20 0.059 Min 0.154 0.161 1.574 +/- 0.008 W 11.9 12.1 0.468 0.476 P 7.9 8.1 0.311 0.319 A0 6.3 6.5 0.248 0.256 B0 5.1 5.3 0.2 0.209 2 2.2 0.079 0.087 K0 t 0.30 +/- 0.05 0.012 +/- 0.002 Ordering Information Part Numbering System SP 4040 - 02 B T G Number of Channels Max P2 D1 Silicon Protection Array Series Inches Min G= Green Part Number Package Marking Min. Order Qty. SP4040-02BTG SOIC-8 SP4040-02 2500 T= Tape & Reel Package B = SOIC-8 ©2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. 155 Revision: March 20, 2012 SP4040 Series SP4040 LF