ENA2181 D

Ordering number : ENA2181A
LV56841PVD
Bi-CDMOS LSI
For Car Audio Systems
http://onsemi.com
Multi-Power Supply IC
Overview
The LV56841PVD is a power supply IC suitable for CD receiver system for car audio system.
This IC integrates 5 systems of regulator output, 2 systems of high side power switch, over-current protector,
overvoltage protector and over-heat protector .
Supply for SW33V outputs is low voltage specification, which enables drastic reduction of power dissipation compared
to the existing model. (the package is HZIP15).
Function
• Low consumption current: 50μA (typ, only VDD output is in operation)
•5 systems of regulator output
VDD for microcontroller: output voltage: 3.3V, maximum output current: 350mA
Reverse current protection implemented.
For system: output voltage: 3.3V, maximum output current: 350mA
For audio: output voltage: 5 to 12V (set by external resistors), maximum output current: 300mA
For illumination: output voltage: 5 to 12V (set by external resistors), maximum output current: 300mA
For CD: output voltage: 6V, maximum output current: 1500mA
• 2 lines of high side switch with interlock VCC
EXT: Maximum output current: 500mA, voltage difference between input and output: 0.75V
ANT: Maximum output current: 300mA, voltage difference between input and output: 0.5V
• Supply input
V6IN: 6V for system (SW33V)
VCC1: For internal reference voltage, control circuits, and VDD output.
VCC2: For AUDIO, illumination, CD, EXT/ANT
• Over-current protector
• Overvoltage protector(OVP): VCC1,VCC2 Typ 21V (All outputs except VDD are turned off)
Overvoltage shutdown(OVS): V6IN Typ 21V (All outputs except VDD are turned off)
• Overheat protector: Typ 175°C
• Pch-LDMOS is used in power output block
(Warning) The protector functions only improve the IC’s tolerance and they do not guarantee the safety of the IC if used under the
conditions out of safety range or ratings. Use of the IC such as use under over-current protection range, thermal shutdown state or V6IN
OVS condition may degrade the IC’s reliability and eventually damage the IC.
HZIP15
ORDERING INFORMATION
See detailed ordering and shipping information on page 15 of this data sheet.
Semiconductor Components Industries, LLC, 2014
August, 2014
82214NK 20140811-S00027/42413NK 20130401-S00001 No.A2181-1/15
LV56841PVD
Absolute Maximum Ratings at Ta = 25°C
Parameter
Symbol
Supply voltage
Conditions
VCC max
VCC1, VCC2
V6IN max
Input voltage
Allowable power dissipation
Ratings
Unit
36
V
V6IN (*)
7
V
VIN max
CTRL1, CTRL2
7
V
Pd max
-Independent IC
Ta ≤ 25°C
1.3
W
Al heat sink *
5.3
W
-Size of heatsink: infinite
26
W
See the appendix for waveform.
50
V
Peak supply voltage
VCC peak
Operating ambient temperature
Topr
-40 to +85
°C
Storage temperature
Tstg
-55 to +150
°C
Junction temperature
Tj max
150
°C
* : When the Aluminum heat sink (50mm × 50mm × 1.5mm) is used
Waveform of surge test (VCC1, VCC2)
*V6IN is designed to tolerant toward short period of
over-voltage (max 20V) which is assumed in condition of short
circuit between VCC1/VCC2 and V6IN.
However, applying over-voltage higher than maximum rating
(7V) to V6IN may degrade the device reliability
50V
90%
10%
16V
5msec
100msec
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
Recommended Operating range at Ta = 25°C
VCC1
Parameter
Operating supply voltage 1
Conditions
Ratings
VDD output
Unit
7 to 16
V
VCC2
Parameter
Operating supply voltage 2
Conditions
Ratings
Unit
ILM output (10V)
12 to 16
V
ILM output (8V)
10 to 16
V
Operating supply voltage 3
AUDIO output (9V)
10 to 16
V
Operating supply voltage 4
CD output (IO = 1.3A)
AUDIO output (5V)
Operating supply voltage 5
8 to 16
V
10.5 to 16
V
CD output (IO ≤ 1A)
10 to 16
V
EXT output, ANT output
10 to 16
V
V6IN
Parameter
Operating supply voltage 6
Conditions
SW33V output
Ratings
Unit
5.5 to 6.5
V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended
Operating Ranges limits may affect device reliability.
No.A2181-2/15
LV56841PVD
Electrical Characteristics : VCC1 = VCC2 = 14.4V, V6IN = 6V at Ta = 25°C (*1)
Parameter
Quiescent current
Symbol
ICC
Conditions
Ratings
min
typ
VDD w/out load, CTRL1/2 = “L/L”
Unit
max
50
100
μA
CTRL1 input (ANT/EXT/ILM)
Low input voltage
VIL1
0.5
V
M1 input voltage
VIM11
0.8
0
1.1
1.4
V
M2 input voltage
VIM21
1.9
2.2
2.5
V
High input voltage
VIH1
Input impedance
RIN1
input voltage ≤ 3.3V
2.9
3.3
5.5
V
280
400
480
kΩ
CTRL2 input (CD/AUDIO/SW33V)
Low input voltage
VIL2
0.5
V
M1 input voltage
VIM12
0.8
0
1.1
1.4
V
M2 input voltage
VIM22
1.9
2.2
2.5
V
High input voltage
VIH2
2.9
3.3
5.5
V
Input impedance
RIN2
280
400
480
kΩ
3.3
3.47
V
input voltage ≤ 3.3V
VDD output (3.3V) (reverse current prevention diode implemented)
Output voltage
VO1
IO1 = 200mA
3.13
Output current
IO1
VO1 ≥ 3.1V
350
Line regulation
ΔVOLN1
7.5V < VCC1 < 16V, IO1 = 200mA
30
90
mV
Load regulation
ΔVOLD1
1mA < IO1 < 200mA
70
150
mV
Dropout voltage1
VDROP11
IO1 = 100mA
2.6
3.1
V
Dropout voltage2
VDROP12
IO1 = 200mA
2.8
3.5
Ripple rejection (*2)
RREJ1
f = 120Hz, VCC1 = 0.5Vpp
Reverse current
Irev
IO1 = 200mA
VO1 = 3.3V, VCC1 = V6IN = 0V
40
mA
50
V
dB
1
50
3.3
3.47
μA
SW33V output (3.3V) ; CTRL2 = “M2 or H”
Output voltage
VO2
IO2 = 200mA
3.13
Output current
IO2
VO2 ≥ 3.1V
350
V
Line regulation
ΔVOLN2
5.7V < V6IN < 6.5V, IO2 = 200mA
30
90
mV
Load regulation
ΔVOLD2
1mA < IO2 < 200mA
70
150
mV
Dropout voltage
VDROP2
IO2 = 200mA
0.25
0.5
Ripple rejection (*2)
RREJ2
f = 120Hz, V6IN or VCC1 = 0.5Vpp
mA
40
50
1.212
1.25
V
dB
IO2 = 200mA
AUDIO (5-12V)output ; CTRL2 = “ H”
AUDIO_F voltage
VI 3
AUDIO_F input current
IIN3
1.288
V
1
μA
AUDIO output voltage 1
VO3
IO3 = 200mA, R3 = 30kΩ, R4 = 5.6kΩ (*3)
7.65
AUDIO output voltage 2
VO3’
IO3 = 200mA, R3 = 27kΩ, R4 = 4.7kΩ (*3)
8.13
8.0
8.35
V
8.5
8.87
AUDIO output voltage 3
VO3’’
IO3 = 200mA, R3 = 24kΩ, R4 = 3.9kΩ (*3)
V
8.6
9.0
9.4
V
AUDIO output voltage 4
VO3’’’
IO3 = 200mA, R3 = 30kΩ, R4 = 10kΩ (*3)
AUDIO output current
IO3
4.75
5.0
5.25
Line regulation
ΔVOLN3
Load regulation
ΔVOLD3
Dropout voltage 1
VDROP3
Ripple rejection (*2)
RREJ3
f = 120Hz, IO3 = 200mA
-1
300
10V < VCC2 < 16V, IO3 = 200mA
V
mA
30
90
mV
1mA < IO3 < 200mA
70
150
mV
IO3 = 200mA
0.4
0.6
40
50
1.212
1.25
V
dB
ILM (5-12V) output ; CTRL2 = “M1 or H”
ILM_F voltage
VI4
ILM_F input current
IIN4
1.288
V
1
μA
ILM output voltage 1
VO4
IO4 = 200mA, R1 = 43kΩ, R2 = 5.1kΩ (*3)
11.21
11.8
12.39
V
ILM output voltage 2
VO4’
IO4 = 200mA, R1 = 56kΩ, R2 = 7.5kΩ (*3)
ILM output voltage 3
VO4’’
IO4 = 200mA, R1 = 30kΩ, R2 = 5.6kΩ (*3)
9.97
10.5
11.03
V
7.6
8.0
8.4
ILM output voltage 4
VO4’’’
IO4 = 200mA, R1 = 30kΩ, R2 = 10kΩ (*3)
V
4.75
5.0
5.25
V
ILM output current
IO4
-1
300
mA
Continued on next page.
No.A2181-3/15
LV56841PVD
Continued from preceding page.
Parameter
Symbol
Conditions
Ratings
min
typ
10V < VCC2 < 16V, IO4 = 200mA
R1 = 30kΩ, R2 = 5.6kΩ
Unit
max
Line regulation
ΔVOLN4
Load regulation
ΔVOLD4
1mA < IO4 < 200mA
Dropout voltage 1
VDROP4
IO4 = 200mA
Dropout voltage 2
VDROP4’
IO4 = 100mA
0.35
Ripple rejection (*2)
RREJ4
f = 120Hz, IO4 = 200mA
40
50
VO5
IO5 = 1000mA
5.7
6.0
Output current
IO5
VO5 ≥ 5.6V
1500
mA
Limit current(*4)
llim5
VO5 ≥ 5.5V
1700
mV
Line regulation
ΔVOLN5
10.5V < VCC2 < 16V, IO5 = 1000mA
50
100
mV
Load regulation
ΔVOLD5
10mA < IO5 < 1000mA
100
200
mV
Dropout voltage 1
VDROP5
IO5 = 1000mA
1.0
1.5
V
Dropout voltage 2
VDROP5’
IO5 = 500mA
0.5
0.75
Ripple rejection (*2)
RREJ5
f = 120Hz, IO5 = 1000mA
30
90
mV
70
150
mV
0.7
1.05
V
0.53
V
dB
CD (6V output) ; CTRL2 = “M1 or M2 or H”
Output voltage
40
50
VCC2-2.5
VCC2-0.75
6.3
V
V
dB
EXT_HS-SW ; CTRL1 = “M1 or M2 or H”
Output voltage
VO6
IO6 = 500mA
Output current
IO6
VO6 ≥ VCC2-2.5
Output voltage
VO7
IO7 = 300mA
Output current
IO7
VO7 ≥ VCC2-1.0
500
V
mA
ANT_HS-SW ; CTRL1 = “H”
VCC2-1.0
VCC2-0.5
300
V
mA
*1 : All the specification is defined based on the tests performed under the conditions where Tj and Ta (= 25°C) are almost equal. These tests were performed
with pulse load to minimize the increase of junction temperature (Tj).
*2 : guaranteed by design
*3 : Using resistors of tolerance within 1%.
*4 : When the output current is over “Ilim5”, the over-current protector circuit operates. The over-current protector circuit is "fold-back" type, and it limits the
output current and voltage when it's operating. The output current should be usually limited below Iomax that is “min of Io5” .
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be
indicated by the Electrical Characteristics if operated under different conditions.
No.A2181-4/15
LV56841PVD
CTRL logic truth table
CTRL1
ANT
ILM
EXT
CTRL2
AUDIO
SW33V
CD
H
ON
ON
ON
H
ON
ON
ON
M2
ON
OFF
ON
M2
OFF
ON
ON
M1
OFF
ON
ON
M1
OFF
OFF
ON
L
OFF
OFF
OFF
L
OFF
OFF
OFF
(Warning) Usage of CTRL pin
When CTRL pin transits between L and M2, since it passes M1, ILM is turned on for a moment. Likewise, when CTRL pin transits between H and M1, since it
passes M2, ILM is turned off for a moment.
To avoid operation failure by the above factors, please refer (1) and (2) as shown below for precaution.dd
z
Do not connect parasitic capacitor to CTRL as much as possible.
z
If use of capacitor for CTRL is required, keep the resistance value as low as possible.
z
Make sure that the output load capacitor has enough margin against the voltage fluctuation due to instantaneous ON/OFF.
(1) The time until a reaction occurs in output after from CTLR ON to OFF (typ)
OFF→ON time
27°C
CTRL1→ILM
6.0μsec
Due to quality fluctuation of ICs in manufacturing process, the above-mentioned time can be shorted by 10 to 20%.
(2)The time until output starts to react shifting from CTRL ON→OFF control :
ON→OFF time
27°C
CTRL1→ILM
2.3μsec
CTRL1/2 voltage range and threshold
μCOM port
5.5V
INAMP
2.2k
CTRL1
H
INANT
3.9k
400k
2.9V
2.65V (typ)
2.5V
1.9V
M2
1.65V (typ)
1.4V
0.8V
0.5V
0V
M1
0.65V (typ)
L
No.A2181-5/15
LV56841PVD
Package Dimensions
unit : mm (typ)
HZIP15
CASE 945AB
ISSUE A
GENERIC
MARKING DIAGRAM*
XXXXXXXXXX
YMDDD
SOLDERING FOOTPRINT*
Through Hole Area
(Unit: mm)
Package name
HZIP15
2.54
1.2
2.54
(1.91)
XXXXX = Specific Device Code
Y = Year
M = Month
DDD = Additional Traceability Data
2.54
2.54
NOTE: The measurements are not to guarantee but for reference only.
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
No.A2181-6/15
LV56841PVD
• Allowable power dissipation derating curve
Pd max -- Ta
Allowable power dissipation, Pd max -- W
8
Aluminum heat sink mounting conditions
tightening torque : 39N×cm, using silicone grease
7
6
5.3
5
Aluminum heat sink (50 × 50 × 1.5mm3) when using
4
3
2
1.3
1
Independent IC (HZIP15)
0
--40
0
--20
20
40
60
80
100
120
140150160
Ambient temperature, Ta -- °C
R1
R3
C2
C4
R2
C1
CD
CTRL2
CTRL1
C5
+
AUDIO
VCC2
ANT
14
13
C15
+
C12 C11
C13
C14
+
C9 C10
EXT
12
11
SW33V
VDD
V6IN
10
9
C7 C8
ILM
GND
CTRL2
CTRL1
8
7
+
R4
C3
6
5
VCC1
4
3
VCC2
2
1
LV56841PVD
AUDIO
CD
ILM
ILM_F
AUDIO_F
Application Circuit Example
15
C16
+
D2
D4
D1
D3
V6IN VDD SW33V
VCC1
ANT
EXT
Peripheral parts
Part name
Description
Recommended value
C1, C3, C5, C13, C14
output stabilization capacitor
greater than10μF (*1)
C2, C4
output stabilization capacitor
0pF
C8, C10, C12
Capacitor for bypass power supply
C8: greater than 100μF
C7, C9, C11
Capacitor for oscillation protector
greater than 0.22μF
Capacitor for EXT/ANT output stabilization
greater than 2.2μF
C10,C12: greater than 47μF
C15, C16
R1/R2
Note
Ceramic capacitor
Make sure to implement close to
VCC and GND.
Use resistors of tolerance within 1%
43kΩ/5.1kΩ : VO = 12V
R1, R2
ILM voltage setting
56kΩ/7.5kΩ : VO = 10.5V
30kΩ/5.6kΩ : VO = 8V
30kΩ/10kΩ : VO = 5V
R3/R4
Use resistors of tolerance within 1%
30kΩ/10kΩ : VO = 5V
R3, R4
AUDIO voltage setting
30kΩ/5.6kΩ : VO = 8.0V
27kΩ/4.7kΩ : VO = 8.5V
24kΩ/3.9kΩ : VO = 9V
D1, D2, D3, D4
Internal device protector diode
ON Semiconductor
SB1003M3
(*1) Make sure that output capacitors are greater than 10uF and meets the condition of ESR = 0.001 to 10Ω , in which voltage/ temperature dependence and
unit differences are taken into consideration. Moreover, in case of electrolytic capacitor, high-frequency characteristics should be sufficiently good.
No.A2181-7/15
LV56841PVD
Block Diagram
6V input
11
V6IN
13
VREF
OVS
3.3V, 0.35A
-
+
VCC1
9
6.5V
OVP
VREG
VREF
VREF
SW33V
+
12
VREG
VDD
3.3V, 0.35A
-
5.8V
1.25V
TSD
VREF
-
+
CTRL1
8
CTRL2
6
5
AUDIO
5 to12V, 0.3A
AUDIO_F
4
CTL
OVP
VREF
TSD
1
-
+
ILM_F
OVP→all outputs except VDD: OFF
TSD→all outputs: OFF
2
VCC2
3
7
OVP
10
ILM
5 to 12V, 0.3A
VREF
-
CD
6V, 1.5A
+
GND
15
EXT
out
14
ANT
out
EXT
VCC2-0.75V, 0.5A
ANT
VCC2-0.5V, 0.3A
No.A2181-8/15
LV56841PVD
Pin Function
Pin No.
1
Pin name
ILM
Description
Equivalent Circuit
ILM output
VCC2
7
When CTRL1 = M1, H,
ILM is ON
1
2
ILM_F
ILM voltage adjust
2
1kΩ
10
3
CD
CD output
GND
VCC2
7
When CTRL2 = M1, M2, H,
CD is ON
6V/1.5A
3
10
4
AUDIO_F
AUDIO voltage adjust
GND
VCC2
7
5
5
AUDIO
AUDIO output
4
When CTRL2 = H
1kΩ
AUDIO is ON
10
6
CTRL2
CTRL2 input
4-value input
GND
9
6
VCC1
10kΩ
85kΩ
185kΩ
0.5V
45kΩ
75kΩ
10
7
VCC2
GND
Power supply
Continued on next page.
No.A2181-9/15
LV56841PVD
Continued from preceding page.
Pin No.
8
Pin name
CTRL1
Description
CTRL1 input
4-value input
Equivalent Circuit
9
VCC1
10kΩ
6
85kΩ
185kΩ
0.5V
45kΩ
75kΩ
10
9
VCC1
Power supply
10
GND
GND
11
V6IN
Power supply
GND
VCC2
VCC1
V6IN
7
9
11
GND
10
12
VDD
VDD output
3.3V/0.35A
VCC1
11
12
10
13
SW33V
SW33V output
When CTRL2 = M2, H
GND
V6IN
11
SW33V is ON
3.3V/0.35A
13
230kΩ
140kΩ
1kΩ
10
14
ANT
ANT output
When CTRL1 = M2, H
GND
VCC2
7
100kΩ
ANT is ON
VCC-0.5V/300mA
14
10
5kΩ
GND
Continued on next page.
No.A2181-10/15
LV56841PVD
Continued from preceding page.
Pin No.
15
Pin name
EXT
Description
EXT output
When CTRL1 = M1, M2, H,
Equivalent Circuit
VCC2
7
100kΩ
EXT is ON
VCC-0.5V/500mA
15
10
5kΩ
GND
No.A2181-11/15
LV56841PVD
Timing Chart
21V
VCC1
(9PIN)
VCC2
(7PIN)
V6IN
(11PIN)
VDD outpit
(12PIN)
H
CTRL1 input
(8PIN)
M2
M1
L
H
M2
CTRL2 input
(6PIN)
M1
L
ILM output
(1PIN)
CD output
(3PIN)
AUDIO output
(5PIN)
ANT output
(14PIN)
EXT output
(15PIN)
SW33V output
(13PIN)
Caution: The above values are obtained when typ.
No.A2181-12/15
LV56841PVD
• How to set AUDIO output voltage
AUDIO output voltage expression
AUDIO = (
5
R1 AUDIO
=
−1
R2
1.25
AUDIO
R1
1.25V
4
R1
+ 1) × 1.25[V ]
R2
AUDIO_F
Set the ratio of R1 and R2 to satisfy above expression.
(ex) AUDIO = 9V setting
R2
AUDIO_F is determined by internal band-gap
reference voltage (typ = 1.25V).
R1
9
=
− 1 = 6.2
R2 1.25
R1
24kΩ
=
≅ 6.15
R2 3.9kΩ
AUDIO = (6.15 + 1) × 1.25V ≅ 8.94V
• ILM output voltage is similarly calculated as AUDIO output.
(ex) ILM = 10.5V setting
R1 10.5
=
− 1 = 7.4
R2 1.25
R1
56kΩ
=
≅ 7.46
R2 7.5kΩ
ILM = (7.46 + 1) × 1.25V ≅ 10.575V
Note : The above values are typical values. These values have variation among the range of their tolerances.
No.A2181-13/15
LV56841PVD
HZIP15 Heat sink attachment
Heat sinks are used to lower the semiconductor device junction temperature by leading the head generated by the device to
the outer environment and dissipating that heat.
a.
Unless otherwise specified, for power ICs with tabs and power ICs with attached heat sinks, solder must not be
applied to the heat sink or tabs.
b.
Heat sink attachment
• Use flat-head screws to attach heat sinks.
• Use also washer to protect the package.
• Use tightening torques in the ranges 39-59Ncm (4-6kgcm) .
• If tapping screws are used, do not use screws with a diameter larger
than the holes in the semiconductor device itself.
• Do not make gap, dust, or other contaminants to get between the
semiconductor device and the tab or heat sink.
• Take care a position of via hole .
• Do not allow dirt, dust, or other contaminants to get between the
semiconductor device and the tab or heat sink.
• Verify that there are no press burrs or screw-hole burrs on the heat sink.
• Warping in heat sinks and printed circuit boards must be no more than
0.05 mm between screw holes, for either concave or convex warping.
• Twisting must be limited to under 0.05 mm.
• Heat sink and semiconductor device are mounted in parallel.
Take care of electric or compressed air drivers
• The speed of these torque wrenches should never exceed 700 rpm,
and should typically be about 400 rpm.
Binding head
machine screw
Countersunk head
mashine screw
Heat sink
gap
Via hole
c.
Silicone grease
• Spread the silicone grease evenly when mounting heat sinks.
• Recommends YG-6260 (Momentive Performance Materials Japan LLC)
d.
Mount
• First mount the heat sink on the semiconductor device, and then mount that assembly on the printed circuit board.
• When attaching a heat sink after mounting a semiconductor device into the printed circuit board, when tightening
up a heat sink with the screw, the mechanical stress which is impossible to the semiconductor device and the pin
doesn't hang.
e.
When mounting the semiconductor device to the heat sink using jigs, etc.,
• Take care not to allow the device to ride onto the jig or positioning dowel.
• Design the jig so that no unreasonable mechanical stress is applied to the semiconductor device.
f.
Heat sink screw holes
• Be sure that chamfering and shear drop of heat sinks must not be larger than the diameter of screw head used.
• When using nuts, do not make the heat sink hole diameters larger than the diameter of the head of the screws used.
A hole diameter about 15% larger than the diameter of the screw is desirable.
• When tap screws are used, be sure that the diameter of the holes in the heat sink are not too small. A diameter about
15% smaller than the diameter of the screw is desirable.
g.
There is a method to mount the semiconductor device to the heat sink by using a spring band. But this method is not
recommended because of possible displacement due to fluctuation of the spring force with time or vibration.
No.A2181-14/15
LV56841PVD
ORDERING INFORMATION
Device
LV56841PVD-XH
Package
HZIP15
(Pb-Free / Halogen Free)
Shipping (Qty / Packing)
20 / Fan-Fold
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States
and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of
SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf . SCILLC reserves the right to make changes without
further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose,
nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including
without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can
and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are
not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or
sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was
negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all
applicable copyright laws and is not for resale in any manner.
PS No.A2181-15/15