NCS2566 D

NCS2566
Six-Channel Video Driver
with Triple SD & Triple
Selectable SD/HD Filters
The NCS2566 integrates reconstruction filters and video amplifiers.
It’s a combination of two 3−channel drivers − the first one capable to
deal with Standard Definition (SD) video signals and a second one
including selectable filters for either Standard or High Definition
(HD) video applications. The filters implemented are 6th order
Butterworth Low Pass filters particularly effective for rejecting
unwanted high frequency components and assuring good linearity of
the phase change over frequency with well optimized group delays.
All channels can accept DC− or AC−coupled signals; when AC−
coupled the internal clamps are employed. The outputs can drive both
AC− and DC−coupled 150 W loads.
It is designed to be compatible with most Digital−to−Analog
Converters (DAC) embedded in video processors. To further reduce
power consumption, two enable pins are provided, one for each triple
driver. One pin allows selection of the filter frequency of the SD/HD
triple driver.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3−Channel with Selectable 6th−Order 8/34 MHz Butterworth Filters
3−Channel with Fixed 6th−Order 8 MHz Butterworth Filters
Transparent Input Clamp for Each Channel
Integrated Level Shifter
AC− or DC−Coupled Inputs and Outputs
Low Quiescent Current
Shutdown Current 42 mA Typical (Disabled)
5 V Power Supply
Each Channel Capable to Drive 2 by 150 W Load
Internal Gain: 6 dB $0.2
Wide Input Common Mode Range
8 kV ESD Protection (IEC61000−4−2 Compatible)
Operating Temperature Range: −40°C to +85°C
Available in a TSSOP−20 Package
These are Pb−Free Devices
• Set−Top Box
• DVD players and related
• HDTV
April, 2011 − Rev. 3
TSSOP−20
DTB SUFFIX
CASE 948E
MARKING DIAGRAM
20
NCS
2566
ALYWG
G
1
A = Assembly Location
L
= Wafer Lot
Y = Year
W = Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
PIN CONNECTIONS
1
20 SD OUT1
SD IN2 2
19 SD OUT2
SD IN3 3
18 SD OUT3
SD EN 4
17 GND
VCC 5
16 GND
SD IN1
SD/HD 6
15 SD/HD EN
SD/HD IN1 7
14 SD/HD OUT1
SD/HD IN2 8
13 SD/HD OUT2
SD/HD IN3 9
12 SD/HD OUT3
NC 10
11 NC
(Top View)
Typical Applications
© Semiconductor Components Industries, LLC, 2011
http://onsemi.com
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 12 of this data sheet.
1
Publication Order Number:
NCS2566/D
NCS2566
SD IN1
1
Transparent Clamp
6dB
20 SD OUT1
6dB
19 SD OUT2
6dB
18 SD OUT3
6th Order,
8 MHz Filter
SD IN2
2
Transparent Clamp
6th Order,
8 MHz Filter
SD IN3
3
Transparent Clamp
6th Order,
8 MHz Filter
SD EN
4
VCC
5
SD/HD
6
SD/HD IN1
7
17 GND
250kW
GND
GND
16 GND
250kW
15 SD/HD EN
Transparent Clamp
6dB
14 SD/HD OUT1
6dB
13 SD/HD OUT2
6dB
12 SD/HD OUT3
6th Order,
Selectable 8/34 MHz Filter
SD/HD IN2
8
Transparent Clamp
6th Order,
Selectable 8/34 MHz Filter
SD/HD IN3
9
Transparent Clamp
6th Order,
Selectable 8/34 MHz Filter
NC
11 NC
10
Figure 1. NCS2566 Block Diagram
http://onsemi.com
2
NCS2566
PIN FUNCTION AND DESCRIPTION
Pin
Name
Type
1
SD IN1
Input
SD Video Input 1 − SD Channel 1
Description
2
SD IN2
Input
SD Video Input 2 − SD Channel 2
3
SD IN3
Input
SD Video Input 3 − SD Channel 3
4
SD EN
Input
SD−Channel Enable/Disable Function: Low = Enable, High = Disable. When left open the default
state is Enable.
5
VCC
Power
6
SD/HD
Input
Pin of selection enabling the Standard Definition or High Definition Filters (8 MHz / 34 MHz) for
channels SD/HD (pins 7−14, 8−13 & 9−12) − when Low SD filters are selected, when High HD
filters are selected.
7
SD/HD IN1
Input
Selectable SD or HD Video Input 1 − SD/HD Channel 1
8
SD/HD IN2
Input
Selectable SD or HD Video Input 2 − SD/HD Channel 2
9
SD/HD IN3
Input
Selectable SD or HD Video Input 3 − SD/HD Channel 3
10
NC
Open
Not Connected
11
NC
Open
Not Connected
12
SD/HD OUT3
Output
SD/HD Video Output 3 − SD/HD Channel 3
13
SD/HD OUT2
Output
SD/HD Video Output 2 − SD/HD Channel 2
14
SD/HD OUT1
Output
SD/HD Video Output 1 − SD/HD Channel 1
15
SD/HD EN
Input
SD/HD Channel Enable /Disable Function: Low = Enable, High = Disable. When left open the
default state is Enable.
16
GND
GND
Connected to Ground
17
GND
GND
Connected to Ground
18
SD OUT3
Output
SD Video Output 3 − SD Channel 3
19
SD OUT2
Output
SD Video Output 2 − SD Channel 2
20
SD OUT1
Output
SD Video Output 1 − SD Channel 1
Device Power Supply Voltage: +5 V $5%
http://onsemi.com
3
NCS2566
MAXIMUM RATINGS
Parameter
Symbol
Rating
Unit
VCC
−0.3 v VCC v 5.5
Vdc
Input Voltage Range
VI
−0.3 v VI v VCC
Vdc
Input Differential Voltage Range
VID
−0.3 v VI v VCC
Vdc
Output Current Per Channel
IO
50
mA
Maximum Junction Temperature (Note 1)
TJ
150
°C
Power Supply Voltages
Operating Ambient Temperature
TA
−40 to +85
°C
Storage Temperature Range
Tstg
−60 to +150
°C
Power Dissipation
PD
(See Graph)
mW
Thermal Resistance, Junction−to−Air
RqJA
125
°C/W
ESD Protection Voltage (IEC61000−4−2)
Vesd
>8000
V
ESD HBM − Human Body Model
HBM
4000
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded.
MAXIMUM POWER DISSIPATION
1800
The maximum power that can be safely dissipated is
limited by the associated rise in junction temperature. For
the plastic packages, the maximum safe junction
temperature is 150°C. If the maximum is exceeded
momentarily, proper circuit operation will be restored as
soon as the die temperature is reduced. Leaving the device
in the “overheated” condition for an extended period can
result in device burnout. To ensure proper operation, it is
important to observe the derating curves.
POWER DISSIPATION (mV)
1600
1400
1200
1000
800
600
400
200
0
−40 −30−20−10
0 10 20 30 40 50 60 70 80 90100
TEMPERATURE (°C)
Figure 2. Power Dissipation vs Temperature
http://onsemi.com
4
NCS2566
DC ELECTRICAL CHARACTERISTICS (VCC = +5.0 V, Rsource = 37.5 W, TA = 25°C, inputs AC−coupled with 0.1 µF, all outputs
AC−coupled with 220 µF into 150 W referenced to 400 kHz; unless otherwise specified)
Symbol
Characteristics
Conditions
Min
Typ
Max
Unit
4.7
5.0
5.3
V
POWER SUPPLY
VCC
Supply Voltage Range
ICC
Supply Current
ISD
3 SD Channels Active
3 HD Channels Active
3 SD + 3 SD Channels Active
3 SD + 3 HD Channels Active
25
40
50
65
80
No Channel Active
42
80
mA
GND
1.4
VPP
0.8
V
Shutdown Current
mA
DC PERFORMANCE
Vi
Input Common Mode Voltage Range
VIL
SD/HD Input Low Level
0
VIH
SD/HD Input High Level
2.4
Rpd
Pulldown Resistors on Pins SD_EN and SD/HD_EN
VCC
V
250
kW
OUTPUT CHARACTERISTICS
VOH
Output Voltage High Level
2.8
V
VOL
Output Voltage Low Level
200
mV
Output Current
40
mA
IO
AC ELECTRICAL CHARACTERISTICS FOR STANDARD DEFINITION CHANNELS (Pin Numbers (1, 20) (2, 19), (3, 18),
(7, 14), (8, 13) & (9, 12)) (VCC = +5.0 V, Vin = 1 VPP, Rsource = 37.5 W, TA = 25°C, Inputs AC−coupled with 0.1 mF, All Outputs
AC−coupled with 220 mF into 150 W Referenced to 400 kHz; unless otherwise specified, SD/HD = Low)
Characteristics
Symbol
AVSD
Voltage Gain
BWSD
Low Pass Filter Bandwidth (Note 3)
Conditions
Min
Typ
Max
Unit
Vin = 1 V − All SD Channels
5.8
6.0
6.2
dB
−1 dB
−3 dB
5.5
6.5
7.2
8.0
@ 27 MHz
43
MHz
ARSD
Stop−Band Attenuation (Note 4)
50
dB
dGSD
Differential Gain Error
0.7
%
dFSD
Differential Phase Error
0.7
°
THD
Total Harmonic Distortion
Vout = 1.4 VPP @ 3.58 MHz
0.35
%
XSD
Channel−to−Channel Crosstalk
@ 1 MHz & Vin = 1.4 VPP
−58
dB
NTC−7 test signal, 100 kHz to
4.2 MHz (Note 2)
72
dB
@ 4.5 MHz
70
ns
100 kHz to 8 MHz
20
ns
SNRSD
DtSD
DGDSD
Signal−to−Noise Ratio
Propagation Delay
Group Delay variation
2. SNR = 20 x log (714 mV/RMS Noise)
3. 100% of Tested ICs fit the bandwidth and attenuation tolerance at 25°C.
4. Guaranteed by Characterization.
http://onsemi.com
5
NCS2566
AC ELECTRICAL CHARACTERISTICS FOR HIGH DEFINITION CHANNELS (Pin Numbers (7, 14), (8, 13) & (9, 12)) (VCC
= +5.0 V, Vin = 1 VPP, Rsource = 37.5 W, TA = 25°C, Inputs AC−coupled with 0.1 mF, All Outputs AC−coupled with 220 mF into 150 W
Referenced to 400 kHz; unless otherwise specified, SD/HD = High)
Characteristics
Symbol
AVHD
Voltage Gain
BWHD
Low Pass Filter Bandwidth
ARHD
Stop−band Attenuation
THDHD
Total Harmonic Distortion
XHD
Channel−to−Channel Crosstalk
SNRHD
Signal−to−Noise Ratio
DtHD
Propagation Delay
DGDHD
Group Delay Variation from
Conditions
Min
Typ
Max
Unit
Vin = 1 V − All HD Channels
5.8
6.0
6.2
dB
−1 dB (Note 6)
−3 dB (Note 7)
26
30
31
34
@ 44.25 MHz (Note 7)
@ 74.25 MHz (Note 6)
33
15
42
dB
Vout = 1.4 VPP @ 10 MHz
Vout = 1.4 VPP @ 15 MHz
Vout = 1.4 VPP @ 22 MHz
0.4
0.6
0.8
%
@ 1 MHz & Vin = 1.4 VPP
−58
dB
white signal, 100 kHz to
30 MHz, (Note 5)
72
dB
25
ns
6.0
ns
100 kHz to 30 MHz
5. SNR = 20 x log (714 mV/RMS Noise)
6. Guaranteed by characterization.
7. 100% of tested ICs fit the bandwidth and attenuation tolerance at 25°C.
http://onsemi.com
6
MHz
NCS2566
TYPICAL CHARACTERISTICS
30
30
20
20
10
10
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
VCC = +5.0 V, Vin = 1 VPP, Rsource = 37.5 W, TA = 25°C, Inputs AC−coupled with 0.1 mF, All Outputs AC−coupled with 220 mF into 150 W
Referenced to 400 kHz; unless otherwise specified
0
−10
−20
−30
−1 dB @ 6.7 MHz
−3 dB @ 8.1 MHz
−53 dB @ 27 MHz
−40
−50
−70
100k
1M
−30
−1 dB @ 31 MHz
−3 dB @ 33 MHz
−16 dB @ 44.25 MHz
−38 dB @ 74.25 MHz
−40
−50
10M
−70
100k
100M
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 3. SD Normalized Frequency Response
Figure 4. HD Normalized Frequency Response
0.4
1.4
0.35
1.2
0.226 dB @ 3.6 MHz
0.3
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
−20
−60
−60
0.25
0.2
0.15
0.1
0.5
0
−0.1
100k
1M
1.0
0.8
0.6
0.4
0.2
0
−0.4
100k
10M
Figure 5. SD Passband Flatness
Figure 6. HD Passband Flatness
30M
−20
−25
−51.8 dB @ 6.85 MHz
−30
−55
−35
−60
−40
GAIN (dB)
−50
−79 dB @ 50 kHz
−50
−55
−80
−60
−85
−65
100k
1M
−70
20
10M
−37.6 dB @ 25 MHz
−45
−75
−90
20k
10M
FREQUENCY (Hz)
−45
−70
1M
FREQUENCY (Hz)
−40
−65
1.035 dB @ 18.7 MHz
−0.2
−0.5
GAIN (dB)
0
−10
−67 dB @ 50 kHz
100k
1M
10M
50M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 7. SD Channel−to−Channel Crosstalk
Figure 8. HD Channel−to−Channel Crosstalk
http://onsemi.com
7
NCS2566
TYPICAL CHARACTERISTICS
30
15
20
10
10
5
GROUP DELAY (ns)
GROUP DELAY (ns)
VCC = +5.0 V, Vin = 1 VPP, Rsource = 37.5 W, TA = 25°C, Inputs AC−coupled with 0.1 mF, All Outputs AC−coupled with 220 mF into 150 W
Referenced to 400 kHz; unless otherwise specified
0
−10
20.7 ns @ 7 MHz
−20
−30
−40
−50
−60
0
−5
9.1 ns @ 24.1 MHz
−10
−15
−20
−25
−30
−70
400k
1M
10M
−35
400k
20M
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 9. SD Normalized Group Delay
Figure 10. HD Normalized Group Delay
Output
0.7 VPP
25 ns
70 ns
Output
0.7 VPP
Input
Figure 11. SD Propagation Delay
Input
Input
Figure 12. HD Propagation Delay
Input
Output
Output
200 mV
200 mV
Figure 13. SD Small Signal Response
Figure 14. HD Small Signal Response
http://onsemi.com
8
NCS2566
TYPICAL CHARACTERISTICS
VCC = +5.0 V, Vin = 1 VPP, Rsource = 37.5 W, TA = 25°C, Inputs AC−coupled with 0.1 mF, All Outputs AC−coupled with 220 mF into 150 W
Referenced to 400 kHz; unless otherwise specified
Output
Input
Output
Input
1 VPP
1 VPP
Figure 15. SD Large Signal Response
Figure 16. HD Large Signal Response
0
−10
−20
PSRR (dB)
−30
−40
−50
−60
−70
−80
−90
−100
20
100k
1M
FREQUENCY (Hz)
10M
Figure 17. SD and HD VCC PSRR vs.
Frequency
http://onsemi.com
9
50M
NCS2566
TYPICAL CHARACTERISTICS
20
60
10
50
0
40
−10
30
−20
20
−30
10
−40
0
−50
−10
−60
−20
−70
−30
−80
400k
1M
−40
50M
10M
(Hz)
NORMALIZED GROUP DELAY (ns)
NORMALIZED GAIN (dB)
VCC = +5.0 V, Vin = 1 VPP, Rsource = 37.5 W, TA = 25°C, Inputs AC−coupled with 0.1 mF, All Outputs AC−coupled with 220 mF into 150 W
Referenced to 400 kHz; unless otherwise specified
20
35
10
30
0
25
−10
20
−20
15
−30
10
−40
5
−50
0
−60
−5
−70
−10
−80
400k
−15
1M
(Hz)
10M
NORMALIZED GROUP DELAY (ns)
NORMALIZED GAIN (dB)
Figure 18. SD Frequency Response and Group
Delay
100M
Figure 19. HD Frequency Response and
Group Delay
0.9
0.9
0.75
0.76
0.77
0.68
0.7
0.6
0.5
0..4
0.31
0.3
0.8
DIFFERENTIAL PHASE (°)
DIFFERENTIAL GAIN (%)
0.8
0.2
0.1
0
0.75
0.7
0.65
0.6
0.5
0..4
0.36
0.3
0.2
0.14
0.07
0.1
0
1
2
3
4
5
0
6
1
2
3
4
5
HARMONIC
HARMONIC
Figure 20. SD Differential Gain
Figure 21. SD Differential Phase
http://onsemi.com
10
6
NCS2566
APPLICATIONS INFORMATION
DAC output signal level and the input common mode
voltage of the video driver. When the configuration is
DC−Coupled at the Inputs and Outputs the 0.1 mF and
220 mF coupling capacitors are no longer used and the
clamps are in that case inactive; this configuration provides
a low cost solution which can be implemented with few
external components.
The input is AC−coupled when either the input−signal
amplitude goes over the range 0 V to 1.4 V or if the video
source requires such a coupling. In some circumstances it
may be necessary to auto−bias signals with the addition of
a pull−up and pull−down resistors or only pull−up resistor
(Typical 7.5 MW combined with the internal 800 kW
pulldown) making the clamp inactive.
The output AC−coupling configuration is advantageous
for eliminating DC ground loop, but may have the drawback
of increasing sensitivity to video line or field tilt issues if the
output coupling capacitor is too small. DC ground loop with
the drawback of making the device more sensitive to video
line or field tilt issues in the case of a too low output coupling
capacitor. In some cases it may be necessary to increase the
nominal 220 mF capacitor value.
All the device pins are protected against electrostatic
discharge at a level of 4 kV HBM and 8 kV according to
IEC61000−4−2. This feature has been considered with a
particular attention with ESD structure able to sustain the
typical values requested by the systems like Set Top Boxes
or Blue-Ray players. This parameter is particularly
important for video driver which usually constitutes the last
stage in the video chain before the video output connector.
The IEC61000-4-2 standard has been used to test our
devices in the real application environment. Test
methodology can be provided on request.
The NCS2566 6−channel video filter driver has been
optimized for Standard and High Definition video
applications covering the requirements of the standards
Composite video (CVBS), S−Video, Component Video
(480i/525i, 576i/625i, 720p/1080i) and related (RGB). The
first 3−channels (SD1, SD2, SD3) are dedicated for
Standard Definition, CVBS and S−Video applications for
which the frequency bandwidth required does not exceed 8
MHz. The 3 other channels (SD/HD1, SD/HD2, SD/HD3)
have selectable filters (8 MHz and 34 MHz) for covering
either standard−definition−like video applications or High
Definition video applications. These frequencies are
selectable using the pin SD/HD. If the application requires,
the video driver outputs may also be disabled using the
SD EN or SD/HD EN required by the application the pins
SD EN or SD/HD EN.
In the regular mode of operation each channel provides an
internal voltage−to−voltage gain of 2 from input to output.
This effectively reduces the number of external components
required as compared to discrete approaches implemented
with stand−alone op amps. An internal level shifter is
employed shifting up the output voltage by adding an offset
of 200 mV. This prevents sync pulse clipping and allows
DC−coupled output to the 150 W video load. In addition the
NCS2566 integrates a 6th−order Butterworth filter for each
channel. This allows rejection of aliases or unwanted
over−sampling effects produced by the video DAC.
Similary for DVD recorders which uses an ADC, this
anti−aliasing filter (reconstruction filter) will avoid picture
quality issues and will aide filtration of parasitic signals
caused by EMI interference.
A built−in diode−like clamp is used in the chip for each
channel to support the AC−coupled mode of operation. The
clamp is active when the input signal goes below 0 V.
The built−in clamp and level shifter allow the device to
operate in different configuration modes depending on the
http://onsemi.com
11
NCS2566
10mF
+5V
0.1mF
0.1mF
1
CVBS
RS
75W
220mF
75W Cables
75W
220mF
75W Cables
75W
220mF
75W Cables
2
OUT2
SD IN2
19
Y
75W
0.1mF
3
C
OUT3
SD IN3
18
C
75W
4
SD EN
SD EN
5
6
SD/HD
0.1mF
Y/G
NCS2566
RS
RS
CVBS
20
75W
0.1mF
Y
RS
OUT1
SD IN1
GND
VCC
SD/HD
7
GND
SD/HD EN
SD/HD IN4 SD/HD OUT4
17
16
15
14
75W
220mF
75W Cables
75W
220mF
75W Cables
75W
220mF
75W Cables
Y/G
75W
0.1mF
Pb/B
13
8
Pb/B
SD/HD IN5 SD/HD OUT5
RS
Pr/R
75W
0.1mF
9 SD/HD IN6 SD/HD OUT6 12
75W
RS
SD/HD EN
Pr/R
AC−Coupling CAPs
10
are Optional
NC
NC
11
AC−Coupling CAPs are Optional
Figure 22. Typical Application
ORDERING INFORMATION
Device
NCS2566DTBR2G
Package
Shipping†
TSSOP−20
(Pb−Free)
2500 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
12
NCS2566
PACKAGE DIMENSIONS
20X
0.15 (0.006) T U
2X
L
TSSOP−20
CASE 948E−02
ISSUE C
K REF
0.10 (0.004)
S
L/2
20
M
T U
S
V
ÍÍÍÍ
ÍÍÍÍ
ÍÍÍÍ
S
J J1
11
B
−U−
PIN 1
IDENT
SECTION N−N
0.25 (0.010)
N
1
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
K
K1
10
M
0.15 (0.006) T U
S
A
−V−
N
F
DETAIL E
−W−
C
G
D
H
0.100 (0.004)
−T− SEATING
DETAIL E
SOLDERING FOOTPRINT
PLANE
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
6.40
6.60
4.30
4.50
--1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.27
0.37
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.252
0.260
0.169
0.177
--0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.011
0.015
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0_
8_
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
13
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCS2566/D