MCR08B, MCR08M Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for line powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection circuits. Supplied in surface mount package for use in automated manufacturing. http://onsemi.com SCRs 0.8 AMPERES RMS 200 thru 600 VOLTS Features • • • • • Sensitive Gate Trigger Current Blocking Voltage to 600 V Glass Passivated Surface for Reliability and Uniformity Surface Mount Package These Devices are Pb−Free and are RoHS Compliant G A MARKING DIAGRAM MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Peak Repetitive Off−State Voltage (Note 1) (Sine Wave, RGK = 1 kW TJ = 25 to 110°C) MCR08B MCR08M VDRM, VRRM On-State Current RMS (All Conduction Angles; TC = 80°C) IT(RMS) 0.8 A Peak Non-repetitive Surge Current (1/2 Cycle Sine Wave, 60 Hz, TC = 25°C) ITSM 8.0 A Circuit Fusing Considerations (t = 8.3 ms) I2t 0.4 A2s PGM 0.1 W Forward Peak Gate Power (TC = 80°C, t = 1.0 ms) Average Gate Power (TC = 80°C, t = 8.3 ms) K Value Unit V 200 600 SOT−223 CASE 318E STYLE 10 1 AYW CR08x G G 1 CR08x = Device Code x = B or M A = Assembly Location Y = Year W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) PIN ASSIGNMENT 1 Cathode PG(AV) 0.01 W 2 Anode Operating Junction Temperature Range TJ −40 to +110 °C 3 Gate Storage Temperature Range Tstg −40 to +150 °C 4 Anode THERMAL CHARACTERISTICS Rating Symbol Value Unit Thermal Resistance, Junction−to−Ambient PCB Mounted per Figure 1 RqJA 156 °C/W Thermal Resistance, Junction−to−Tab Measured on Anode Tab Adjacent to Epoxy RqJT 25 TL 260 Maximum Device Temperature for Soldering Purposes (for 10 Seconds Maximum) October, 2013 − Rev. 7 1 Shipping† Device Package °C/W MCR08BT1G SOT−223 (Pb−Free) 1000/Tape &Reel °C MCR08MT1G SOT−223 (Pb−Free) 1000/Tape & Reel Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant source such that the voltage ratings of the devices are exceeded. © Semiconductor Components Industries, LLC, 2013 ORDERING INFORMATION †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Publication Order Number: MCR08BT1/D MCR08B, MCR08M ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted) Characteristic Symbol Min Typ Max Unit − − − − 10 200 mA mA OFF CHARACTERISTICS IDRM, IRRM Peak Repetitive Forward or Reverse Blocking Current (Note 3) (VAK = Rated VDRM or VRRM, RGK = 1 kW TJ = 25°C TJ = 110°C ON CHARACTERISTICS Peak Forward On-State Voltage (Note 2) (IT = 1.0 A Peak) VTM − − 1.7 V Gate Trigger Current (Continuous dc) (Note 4) (VAK = 12 Vdc, RL = 100 W) IGT − − 200 mA Holding Current (Note 3) (VAK = 12 Vdc, Initiating Current = 20 mA) IH − − 5.0 mA VGT − − 0.8 V tgt − 1.25 − ms 10 − − Gate Trigger Voltage (Continuous dc) (Note 4) (VAK = 12 Vdc, RL = 100 W) Turn−On Time (VAK = 12 Vdc, ITM = 5 Adc, IGT = 5 mA) DYNAMIC CHARACTERISTICS dv/dt Critical Rate-of-Rise of Off State Voltage (Vpk = Rated VDRM, TC = 110°C, RGK = 1 kW, Exponential Method) V/ms 2. Pulse Test: Pulse Width ≤ 300 ms, Duty Cycle ≤ 2%. 3. RGK = 1000 W is included in measurement. 4. RGK is not included in measurement. Voltage Current Characteristic of SCR Symbol Parameter VDRM Peak Repetitive Off State Forward Voltage IDRM Peak Forward Blocking Current VRRM Peak Repetitive Off State Reverse Voltage IRRM Peak Reverse Blocking Current VTM Peak On State Voltage IH Holding Current Reverse Avalanche Region Anode − 0.091 0.091 2.3 2.3 0.079 2.0 0.059 0.059 0.059 1.5 1.5 1.5 0.096 2.44 0.096 2.44 IH + Voltage IDRM at VDRM Forward Blocking Region (off state) 0.244 6.2 ǒinches Ǔ mm 0.096 2.44 0.059 1.5 0.059 1.5 on state Reverse Blocking Region (off state) 0.079 2.0 Anode + VTM IRRM at VRRM 0.15 3.8 0.984 25.0 + Current BOARD MOUNTED VERTICALLY IN CINCH 8840 EDGE CONNECTOR. BOARD THICKNESS = 65 MIL., FOIL THICKNESS = 2.5 MIL. MATERIAL: G10 FIBERGLASS BASE EPOXY 0.472 12.0 Figure 1. PCB for Thermal Impedance and Power Testing of SOT-223 http://onsemi.com 2 1.0 0.1 TYPICAL AT TJ = 110°C MAX AT TJ = 110°C MAX AT TJ = 25°C 0.01 1.0 0 2.0 4.0 3.0 160 150 140 130 120 110 100 90 80 70 60 50 40 30 DEVICE MOUNTED ON FIGURE 1 AREA = L2 AS SHOWN 1 2 3 MINIMUM FOOTPRINT = 0.076 cm2 0 1.0 100 α T A , MAXIMUM ALLOWABLE AMBIENT TEMPERATURE ( °C) 50 OR 60 Hz HALFWAVE 90 α = CONDUCTION ANGLE 80 dc 70 180° 60 120° α = 30° 40 60° 5.0 6.0 7.0 8.0 9.0 90° 180° 80 120° 70 α = 30° 60 60° 50 40 20 0.1 0.2 0.5 0.4 0.3 90° α 30 α = 0 CONDUCTION ANGLE 0 0.1 0.2 0.3 0.4 0.5 IT(AV), AVERAGE ON‐STATE CURRENT (AMPS) IT(AV), AVERAGE ON‐STATE CURRENT (AMPS) Figure 4. Current Derating, Minimum Pad Size Reference: Ambient Temperature Figure 5. Current Derating, 1.0 cm Square Pad Reference: Ambient Temperature dc 100 110 PAD AREA = 4.0 cm2, 50 OR 60 Hz HALFWAVE 120° α = 30° 60° 70 90° α 180° 120° α = 30° 60° 90° α α = CONDUCTION α = CONDUCTION ANGLE ANGLE 0.1 50 OR 60 Hz HALFWAVE dc 180° 90 10 1.0 cm2 FOIL, 50 OR 60 Hz HALFWAVE dc 20 0 4.0 90 30 50 3.0 Figure 3. Junction to Ambient Thermal Resistance versus Copper Tab Area 100 60 2.0 Figure 2. On-State Characteristics 110 80 L 4 PCB WITH TAB AREA FOIL AREA (cm2) 110 50 L TYPICAL MAXIMUM vT, INSTANTANEOUS ON‐STATE VOLTAGE (VOLTS) 110 T A , MAXIMUM ALLOWABLE AMBIENT TEMPERATURE ( °C) R θJA , JUNCTION TO AMBIENT THERMAL RESISTANCE, ( °C/W) 10 T(tab) , MAXIMUM ALLOWABLE TAB TEMPERATURE ( ° C) T A , MAXIMUM ALLOWABLE AMBIENT TEMPERATURE ( °C) IT, INSTANTANEOUS ON‐STATE CURRENT (AMPS) MCR08B, MCR08M 0.2 0.3 0.4 85 0.5 0 IT(AV), AVERAGE ON‐STATE CURRENT (AMPS) 0.1 0.2 0.3 0.4 IT(AV), AVERAGE ON‐STATE CURRENT (AMPS) Figure 6. Current Derating, 2.0 cm Square Pad Reference: Ambient Temperature Figure 7. Current Derating Reference: Anode Tab http://onsemi.com 3 0.5 MCR08B, MCR08M 1.0 MAXIMUM AVERAGE POWER P(AV),DISSIPATION (WATTS) 0.9 0.8 α = 0.7 α r T , TRANSIENT THERMAL RESISTANCE NORMALIZED 1.0 α = 30° CONDUCTION ANGLE 60° 0.6 90° 0.5 0.4 dc 0.3 180° 0.2 120° 0.1 0 0 0.1 0.2 0.01 0.0001 0.5 0.4 0.3 0.1 0.001 VAK = 12 V RL = 100 W 0.6 I H , HOLDING CURRENT (NORMALIZED) VGT , GATE TRIGGER VOLTAGE (VOLTS) 100 2.0 0.5 0.4 -20 0 20 40 60 80 VAK = 12 V RL = 3.0 kW 1.0 0 -40 110 -20 0 20 40 60 80 110 TJ, JUNCTION TEMPERATURE, (°C) TJ, JUNCTION TEMPERATURE, (°C) Figure 10. Typical Gate Trigger Voltage versus Junction Temperature Figure 11. Typical Normalized Holding Current versus Junction Temperature 1000 I GT , GATE TRIGGER CURRENT ( μA) 0.7 V GT , GATE TRIGGER VOLTAGE (VOLTS) 10 Figure 9. Thermal Response Device Mounted on Figure 1 Printed Circuit Board 0.7 0.65 0.6 RGK = 1000 W, RESISTOR CURRENT INCLUDED 100 0.55 0.5 VAK = 12 V RL = 100 W TJ = 25°C 0.45 0.4 0.35 0.3 0.1 1.0 t, TIME (SECONDS) Figure 8. Power Dissipation 0.3 -40 0.1 0.01 IT(AV), AVERAGE ON‐STATE CURRENT (AMPS) 1.0 10 100 1000 VAK = 12 V RL = 100 W WITHOUT GATE RESISTOR 10 1.0 -40 -20 0 20 40 60 80 TJ, JUNCTION TEMPERATURE (°C) IGT, GATE TRIGGER CURRENT (mA) Figure 12. Typical Range of VGT versus Measured IGT Figure 13. Typical Gate Trigger Current versus Junction Temperature http://onsemi.com 4 110 MCR08B, MCR08M 10000 100 IGT = 48 mA 10 Vpk = 400 V 1000 STATIC dv/dt (V/ μS) IH , HOLDING CURRENT (mA) 5000 TJ = 25°C IGT = 7 mA 1.0 500 100 TJ = 25° 50 10 125° 5.0 50° 110° 1.0 75° 0.5 0.1 1.0 10 10,000 100 1000 10,000 100,000 RGK, GATE‐CATHODE RESISTANCE (OHMS) Figure 14. Holding Current Range versus Gate-Cathode Resistance Figure 15. Exponential Static dv/dt versus Junction Temperature and Gate-Cathode Termination Resistance 10000 300 V 1000 TJ = 110°C 1000 200 V 500 0.1 10 100,000 RGK, GATE‐CATHODE RESISTANCE (OHMS) 10000 100 V TJ = 110°C 400 V (PEAK) 500 100 STATIC dv/dt (V/ μS) 400 V 50 V 50 500 V 10 5.0 100 RGK = 100 50 10 RGK = 1.0 k 5.0 1.0 10 100 1000 10,000 RGK = 10 k 1.0 0.01 0.1 1.0 10 RGK, GATE‐CATHODE RESISTANCE (OHMS) CGK, GATE‐CATHODE CAPACITANCE (nF) Figure 16. Exponential Static dv/dt versus Peak Voltage and Gate-Cathode Termination Resistance Figure 17. Exponential Static dv/dt versus Gate-Cathode Capacitance and Resistance 10000 1000 500 STATIC dv/dt (V/ μS) STATIC dv/dt (V/ μS) 1000 100 100 50 IGT = 70 mA 10 IGT = 5 mA IGT = 35 mA 5.0 1.0 10 IGT = 15 mA 100 1000 10,000 GATE‐CATHODE RESISTANCE (OHMS) Figure 18. Exponential Static dv/dt versus Gate-Cathode Termination Resistance and Product Trigger Current Sensitivity http://onsemi.com 5 100,000 100 MCR08B, MCR08M PACKAGE DIMENSIONS SOT−223 (TO−261) CASE 318E−04 ISSUE L NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. D b1 DIM A A1 b b1 c D E e e1 L1 HE 4 HE E 1 2 3 b e1 e 0.08 (0003) q C q A A1 MIN 1.50 0.02 0.60 2.90 0.24 6.30 3.30 2.20 0.85 1.50 6.70 0° MILLIMETERS NOM MAX 1.63 1.75 0.06 0.10 0.75 0.89 3.06 3.20 0.29 0.35 6.50 6.70 3.50 3.70 2.30 2.40 0.94 1.05 1.75 2.00 7.00 7.30 10° − MIN 0.060 0.001 0.024 0.115 0.009 0.249 0.130 0.087 0.033 0.060 0.264 0° INCHES NOM 0.064 0.002 0.030 0.121 0.012 0.256 0.138 0.091 0.037 0.069 0.276 − MAX 0.068 0.004 0.035 0.126 0.014 0.263 0.145 0.094 0.041 0.078 0.287 10° STYLE 10: PIN 1. CATHODE 2. ANODE 3. GATE 4. ANODE L1 SOLDERING FOOTPRINT* 3.8 0.15 2.0 0.079 2.3 0.091 2.3 0.091 6.3 0.248 2.0 0.079 1.5 0.059 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MCR08BT1/D