HA5023 September 1998 File Number 3393.6 Dual 125MHz Video Current Feedback Amplifier Features The HA5023 is a wide bandwidth high slew rate dual amplifier optimized for video applications and gains between 1 and 10. It is a current feedback amplifier and thus yields less bandwidth degradation at high closed loop gains than voltage feedback amplifiers. • Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475V/µs The low differential gain and phase, 0.1dB gain flatness, and ability to drive two back terminated 75Ω cables, make this amplifier ideal for demanding video applications. • Supply Current (per Amplifier) . . . . . . . . . . . . . . . . 7.5mA • Wide Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 125MHz The current feedback design allows the user to take advantage of the amplifier’s bandwidth dependency on the feedback resistor. By reducing RF, the bandwidth can be increased to compensate for decreases at higher closed loop gains or heavy output loads. The performance of the HA5023 is very similar to the popular Intersil HA-5020. • Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . 800µV • Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03% • Differential Phase . . . . . . . . . . . . . . . . . . . . 0.03 Degrees • ESD Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V • Guaranteed Specifications at ±5V Supplies Applications • Video Gain Block • Video Distribution Amplifier/RGB Amplifier • Flash A/D Driver • Current to Voltage Converter Ordering Information PART NUMBER (BRAND) TEMP. RANGE (oC) • Medical Imaging PACKAGE PKG. NO. HA5023IP -40 to 85 8 Ld PDIP E8.3 HA5023IB (H5023I) -40 to 85 8 Ld SOIC M8.15 HA5023EVAL • Radar and Imaging Systems • Video Switching and Routing Pinout HA5023 (PDIP, SOIC) TOP VIEW High Speed Op Amp DIP Evaluation Board 1 OUT1 1 -IN1 2 +IN1 3 V- 4 -+ +- 8 V+ 7 OUT2 6 -IN2 5 +IN2 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999 HA5023 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . .36V DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . ±VSUPPLY Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V Output Current (Note 4) . . . . . . . . . . . . . . . . .Short Circuit Protected ESD Rating (Note 3) Human Body Model (Per MIL-STD-883 Method 3015.7) . . . 2000V Thermal Resistance (Typical, Note 2) θJA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . .175oC Maximum Junction Temperature (Plastic Package, Note 1) . .150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC Supply Voltage Range (Typical) . . . . . . . . . . . . . . . . . ±4.5V to ±15V CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175oC for die, and below 150oC for plastic packages. See Application Information section for safe operating area information. 2. θJA is measured with the component mounted on an evaluation PC board in free air. 3. The non-inverting input of unused amplifiers must be connected to GND. 4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle) output current should not exceed 15mA for maximum reliability. VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified Electrical Specifications (NOTE 9) TEST LEVEL TEMP. (oC) MIN TYP MAX UNITS A 25 - 0.8 3 mV A Full - - 5 mV Delta VIO Between Channels A Full - 1.2 3.5 mV Average Input Offset Voltage Drift B Full - 5 - µV/oC A 25 53 - - dB A Full 50 - - dB A 25 60 - - dB A Full 55 - - dB A Full ±2.5 - - V A 25 - 3 8 µA A Full - - 20 µA A 25 - - 0.15 µA/V A Full - - 0.5 µA/V A 25 - - 0.1 µA/V A Full - - 0.3 µA/V A 25, 85 - 4 12 µA A -40 - 10 30 µA A 25, 85 - 6 15 µA A -40 - 10 30 µA PARAMETER TEST CONDITIONS INPUT CHARACTERISTICS Input Offset Voltage (VIO) VIO Common Mode Rejection Ratio VIO Power Supply Rejection Ratio Input Common Mode Range Note 5 ±3.5V ≤ VS ≤ ±6.5V Note 5 Non-Inverting Input (+IN) Current +IN Common Mode Rejection (+IBCMR = 1 +RIN Note 5 ) ±3.5V ≤ VS ≤ ±6.5V +IN Power Supply Rejection Inverting Input (-IN) Current Delta -IN BIAS Current Between Channels 2 HA5023 VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified (Continued) Electrical Specifications PARAMETER TEST CONDITIONS -IN Common Mode Rejection Note 5 ±3.5V ≤ VS ≤ ±6.5V -IN Power Supply Rejection (NOTE 9) TEST LEVEL TEMP. (oC) MIN TYP MAX UNITS A 25 - - 0.4 µA/V A Full - - 1.0 µA/V A 25 - - 0.2 µA/V A Full - - 0.5 µA/V Input Noise Voltage f = 1kHz B 25 - 4.5 - nV/√Hz +Input Noise Current f = 1kHz B 25 - 2.5 - pA/√Hz -Input Noise Current f = 1kHz B 25 - 25.0 - pA/√Hz Note 11 A 25 1.0 - - MΩ A Full 0.85 - - MΩ A 25 70 - - dB A Full 65 - - dB A 25 50 - - dB A Full 45 - - dB A 25 ±2.5 ±3.0 - V A Full ±2.5 ±3.0 - V TRANSFER CHARACTERISTICS Transimpedence RL = 400Ω, VOUT = ±2.5V Open Loop DC Voltage Gain RL = 100Ω, VOUT = ±2.5V Open Loop DC Voltage Gain OUTPUT CHARACTERISTICS Output Voltage Swing RL = 150Ω Output Current RL = 150Ω B Full ±16.6 ±20.0 - mA Output Current, Short Circuit VIN = ±2.5V, VOUT = 0V A Full ±40 ±60 - mA Supply Voltage Range A 25 5 - 15 V Quiescent Supply Current A Full - 7.5 10 mA/Op Amp POWER SUPPLY CHARACTERISTICS AC CHARACTERISTICS (AV = +1) Slew Rate Note 6 B 25 275 350 - V/µs Full Power Bandwidth Note 7 B 25 22 28 - MHz Rise Time Note 8 B 25 - 6 - ns Fall Time Note 8 B 25 - 6 - ns Propagation Delay Note 8 B 25 - 6 - ns B 25 - 4.5 - % Overshoot -3dB Bandwidth VOUT = 100mV B 25 - 125 - MHz Settling Time to 1% 2V Output Step B 25 - 50 - ns Settling Time to 0.25% 2V Output Step B 25 - 75 - ns 3 HA5023 VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified (Continued) Electrical Specifications PARAMETER TEST CONDITIONS (NOTE 9) TEST LEVEL TEMP. (oC) MIN TYP MAX UNITS AC CHARACTERISTICS (AV = +2, RF = 681Ω) Slew Rate Note 6 B 25 - 475 - V/µs Full Power Bandwidth Note 7 B 25 - 26 - MHz Rise Time Note 8 B 25 - 6 - ns Fall Time Note 8 B 25 - 6 - ns Propagation Delay Note 8 B 25 - 6 - ns B 25 - 12 - % Overshoot -3dB Bandwidth VOUT = 100mV B 25 - 95 - MHz Settling Time to 1% 2V Output Step B 25 - 50 - ns Settling Time to 0.25% 2V Output Step B 25 - 100 - ns Gain Flatness 5MHz B 25 - 0.02 - dB 20MHz B 25 - 0.07 - dB AC CHARACTERISTICS (AV = +10, RF = 383Ω) Slew Rate Note 6 B 25 350 475 - V/µs Full Power Bandwidth Note 7 B 25 28 38 - MHz Rise Time Note 8 B 25 - 8 - ns Fall Time Note 8 B 25 - 9 - ns Propagation Delay Note 8 B 25 - 9 - ns B 25 - 1.8 - % Overshoot -3dB Bandwidth VOUT = 100mV B 25 - 65 - MHz Settling Time to 1% 2V Output Step B 25 - 75 - ns Settling Time to 0.1% 2V Output Step B 25 - 130 - ns Differential Gain (Note 10) RL = 150Ω B 25 - 0.03 - % Differential Phase (Note 10) RL = 150Ω B 25 - 0.03 - Degrees VIDEO CHARACTERISTICS NOTES: 5. VCM = ±2.5V. At -40oC Product is tested at VCM = ±2.25V because Short Test Duration does not allow self heating. 6. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points. Slew Rate 7. FPBW = ----------------------------- ; V = 2V . 2πV PEAK PEAK 8. RL = 100Ω, VOUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay. 9. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only. 10. Measured with a VM700A video tester using an NTC-7 composite VITS. 11. VOUT = ±2.5V. At -40oC Product is tested at VOUT = ±2.25V because Short Test Duration does not allow self heating. 4 HA5023 Test Circuits and Waveforms + DUT 50Ω HP4195 NETWORK ANALYZER 50Ω FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS (NOTE 12) 100Ω (NOTE 12) 100Ω VIN + VIN DUT VOUT - 50Ω RL 100Ω + DUT VOUT - 50Ω RI 681Ω RF, 681Ω RL 400Ω RF, 1kΩ FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT FIGURE 3. LARGE SIGNAL PULSE RESPONSE CIRCUIT NOTE: 12. A series input resistor of ≥100Ω is recommended to limit input currents in case input signals are present before the HA5023 is powered up. Vertical Scale: VIN = 100mV/Div., VOUT = 100mV/Div. Horizontal Scale: 20ns/Div. FIGURE 4. SMALL SIGNAL RESPONSE 5 Vertical Scale: VIN = 1V/Div., VOUT = 1V/Div. Horizontal Scale: 50ns/Div. FIGURE 5. LARGE SIGNAL RESPONSE Schematic Diagram (One Amplifier of Two) V+ R5 2.5K R2 800 R10 820 QP8 R15 400 QP9 R19 400 QP11 QP1 QP5 QP14 R11 1K R17 280 QN5 6 QP15 QN12 R24 140 QP16 QP20 R20 140 C1 1.4pF QN8 QP2 QP12 R28 20 QP6 R1 60K QN6 QN1 -IN R12 280 QP4 QP17 QN13 +IN QN17 C2 1.4pF QN2 QN4 QN3 R14 280 R22 280 QN15 QN21 R25 140 QN18 QN14 R13 1K QN7 R25 20 R21 140 QN10 QP7 HA5023 QP13 R3 6K D1 QP19 R31 5 R18 280 QP10 R29 9.5 R27 200 QN16 R16 400 R23 400 R26 200 R32 5 QN19 R30 7 OUT R4 800 V- R33 800 R9 820 QN9 QN11 HA5023 Application Information traces connected to -IN, and that connections to -IN be kept as short as possible to minimize the capacitance from this node to ground. Optimum Feedback Resistor The plots of inverting and non-inverting frequency response, see Figure 8 and Figure 9 in the typical performance section, illustrate the performance of the HA5023 in various closed loop gain configurations. Although the bandwidth dependency on closed loop gain isn’t as severe as that of a voltage feedback amplifier, there can be an appreciable decrease in bandwidth at higher gains. This decrease may be minimized by taking advantage of the current feedback amplifier’s unique relationship between bandwidth and RF. All current feedback amplifiers require a feedback resistor, even for unity gain applications, and RF, in conjunction with the internal compensation capacitor, sets the dominant pole of the frequency response. Thus, the amplifier’s bandwidth is inversely proportional to RF. The HA5023 design is optimized for a 1000Ω RF at a gain of +1. Decreasing RF in a unity gain application decreases stability, resulting in excessive peaking and overshoot. At higher gains the amplifier is more stable, so RF can be decreased in a tradeoff of stability for bandwidth. The table below lists recommended RF values for various gains, and the expected bandwidth. Driving Capacitive Loads Capacitive loads will degrade the amplifier’s phase margin resulting in frequency response peaking and possible oscillations. In most cases the oscillation can be avoided by placing an isolation resistor (R) in series with the output as shown in Figure 6. 100Ω VIN R + VOUT - RT CL RF RI FIGURE 6. PLACEMENT OF THE OUTPUT ISOLATION RESISTOR, R The selection criteria for the isolation resistor is highly dependent on the load, but 27Ω has been determined to be a good starting value. Power Dissipation Considerations RF (Ω) BANDWIDTH (MHz) -1 750 100 +1 1000 125 +2 681 95 +5 1000 52 +10 383 65 -10 750 22 PC Board Layout The frequency response of this amplifier depends greatly on the amount of care taken in designing the PC board. The use of low inductance components such as chip resistors and chip capacitors is strongly recommended. If leaded components are used the leads must be kept short especially for the power supply decoupling components and those components connected to the inverting input. Attention must be given to decoupling the power supplies. A large value (10µF) tantalum or electrolytic capacitor in parallel with a small value (0.1µF) chip capacitor works well in most cases. A ground plane is strongly recommended to control noise. Care must also be taken to minimize the capacitance to ground seen by the amplifier’s inverting input (-IN). The larger this capacitance, the worse the gain peaking, resulting in pulse overshoot and possible instability. It is recommended that the ground plane be removed under 7 Due to the high supply current inherent in dual amplifiers, care must be taken to insure that the maximum junction temperature (TJ , see Absolute Maximum Ratings) is not exceeded. Figure 7 shows the maximum ambient temperature versus supply voltage for the available package styles (Plastic DIP, SOIC). At ±5VDC quiescent operation both package styles may be operated over the full industrial range of -40oC to 85oC. It is recommended that thermal calculations, which take into account output power, be performed by the designer. MAX AMBIENT TEMPERATURE (oC) GAIN (ACL) 140 130 120 PDIP 110 100 90 SOIC 80 70 60 50 5 7 9 11 13 15 SUPPLY VOLTAGE (±V) FIGURE 7. MAXIMUM OPERATING AMBIENT TEMPERATURE vs SUPPLY VOLTAGE HA5023 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified 5 5 VOUT = 0.2VP-P CL = 10pF 4 AV = +1, RF = 1kΩ AV = 2, RF = 681Ω 2 3 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 3 AV = 5, RF = 1kΩ 1 0 -1 -2 -3 VOUT = 0.2VP-P CL = 10pF RF = 750Ω 4 AV = 10, RF = 383Ω -4 AV = -1 2 1 AV = -2 0 -1 -2 AV = -10 -3 AV = -5 -4 -5 10 100 -5 200 FREQUENCY (MHz) 2 180 AV = +1, RF = 1kΩ 135 -45 90 AV = -1, RF = 750Ω -135 45 AV = +10, RF = 383Ω -100 0 -225 -45 -270 -90 AV = -10, RF = 750Ω -135 -315 VOUT = 0.2VP-P CL = 10pF -360 2 140 VOUT = 0.2VP-P CL = 10pF AV = +1 130 120 100 5 GAIN PEAKING 500 200 700 FREQUENCY (MHz) 0 1500 130 VOUT = 0.2VP-P CL = 10pF AV = +2 95 -3dB BANDWIDTH 90 10 5 GAIN PEAKING 500 650 800 950 0 1100 FEEDBACK RESISTOR (Ω) FIGURE 12. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE 8 -3dB BANDWIDTH (MHz) 100 GAIN PEAKING (dB) -3dB BANDWIDTH (MHz) 900 1100 1300 FEEDBACK RESISTOR (Ω) FIGURE 11. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE FIGURE 10. PHASE RESPONSE AS A FUNCTION OF FREQUENCY 350 10 -3dB BANDWIDTH -180 10 200 120 -3dB BANDWIDTH 110 6 100 4 90 GAIN PEAKING 80 0 200 400 VOUT = 0.2VP-P CL = 10pF AV = +1 600 800 2 0 1000 LOAD RESISTOR (Ω) FIGURE 13. BANDWIDTH AND GAIN PEAKING vs LOAD RESISTANCE GAIN PEAKING (dB) -90 -3dB BANDWIDTH (MHz) 0 100 FIGURE 9. INVERTING FREQUENCY RESPONSE INVERTING PHASE (DEGREES) NONINVERTING PHASE (DEGREES) FIGURE 8. NON-INVERTING FREQENCY RESPONSE 10 FREQUENCY (MHz) GAIN PEAKING (dB) 2 HA5023 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 16 VOUT = 0.1VP-P CL = 10pF VOUT = 0.2VP-P CL = 10pF AV = +10 VSUPPLY = ±5V, AV = +2 60 12 OVERSHOOT (%) -3dB BANDWIDTH (MHz) 80 40 VSUPPLY = ±15V, AV = +2 6 20 VSUPPLY = ±5V, AV = +1 VSUPPLY = ±15V, AV = +1 0 0 200 350 500 650 800 0 950 200 400 600 LOAD RESISTANCE (Ω) FEEDBACK RESISTOR (Ω) 0.08 0.10 FREQUENCY = 3.58MHz 0.08 DIFFERENTIAL PHASE (DEGREES) FREQUENCY = 3.58MHz DIFFERENTIAL GAIN (%) 1000 FIGURE 15. SMALL SIGNAL OVERSHOOT vs LOAD RESISTANCE FIGURE 14. BANDWIDTH vs FEEDBACK RESISTANCE RL = 75Ω 0.06 RL = 150Ω 0.04 0.02 RL = 1kΩ 0.06 0.04 RL = 150Ω RL = 75Ω 0.02 RL = 1kΩ 0.00 0.00 3 5 7 9 11 SUPPLY VOLTAGE (±V) 13 3 15 -40 VOUT = 2.0VP-P CL = 30pF 0 REJECTION RATIO (dB) HD2 -60 3RD ORDER IMD HD2 HD3 13 15 AV = +1 -20 -30 -40 -50 CMRR -60 NEGATIVE PSRR -70 -80 -80 HD3 -90 0.3 7 9 11 SUPPLY VOLTAGE (±V) -10 -50 -70 5 FIGURE 17. DIFFERENTIAL PHASE vs SUPPLY VOLTAGE FIGURE 16. DIFFERENTIAL GAIN vs SUPPLY VOLTAGE DISTORTION (dBc) 800 1 FREQUENCY (MHz) FIGURE 18. DISTORTION vs FREQUENCY 9 10 0.001 POSITIVE PSRR 0.01 0.1 1 10 FREQUENCY (MHz) FIGURE 19. REJECTION RATIOS vs FREQUENCY 30 HA5023 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 12 RL = 100Ω VOUT = 1.0VP-P AV = +1 RLOAD = 100Ω VOUT = 1.0VP-P PROPAGATION DELAY (ns) PROPAGATION DELAY (ns) 8.0 7.5 7.0 6.5 10 AV = +10, RF = 383Ω 8 AV = +2, RF = 681Ω 6 AV = +1, RF = 1kΩ 6.0 -50 -25 0 25 50 75 100 4 125 3 5 7 9 11 SUPPLY VOLTAGE (±V) TEMPERATURE (C) FIGURE 20. PROPAGATION DELAY vs TEMPERATURE 15 FIGURE 21. PROPAGATION DELAY vs SUPPLY VOLTAGE 500 0.8 VOUT = 2VP-P NORMALIZED GAIN (dB) + SLEW RATE 400 VOUT = 0.2VP-P CL = 10pF 0.6 450 SLEW RATE (V/µs) 13 350 - SLEW RATE 300 250 200 0.4 0.2 AV = +2, RF = 681Ω 0 -0.2 -0.4 AV = +5, RF = 1kΩ -0.6 AV = +1, RF = 1kΩ -0.8 150 -1.0 100 AV = +10, RF = 383Ω -1.2 -25 0 25 50 75 100 125 5 10 TEMPERATURE (oC) FIGURE 22. FIGURE 22. SLEW RATE vs TEMPERATURE VOLTAGE NOISE (nV/√Hz) NORMALIZED GAIN (dB) 0 AV = -1 -0.2 -0.4 -0.6 AV = -5 -0.8 -1.2 10 -INPUT NOISE CURRENT 80 800 600 60 +INPUT NOISE CURRENT 400 40 INPUT NOISE VOLTAGE 200 20 AV = -2 AV = -10 5 1000 AV = +10, RF = 383Ω 0.2 -1.0 30 100 VOUT = 0.2VP-P CL = 10pF RF = 750Ω 0.4 25 FIGURE 23. NON-INVERTING GAIN FLATNESS vs FREQUENCY 0.8 0.6 15 20 FREQUENCY (MHz) 15 20 25 30 FREQUENCY (MHz) FIGURE 24. INVERTING GAIN FLATNESS vs FREQUENCY 10 0 0.01 0.1 1 FREQUENCY (kHz) 10 0 100 FIGURE 25. INPUT NOISE CHARACTERISTICS CURRENT NOISE (pA/√Hz) -50 HA5023 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 1.5 BIAS CURRENT (µA) 2 VIO (mV) 1.0 0.5 0.0 -60 -40 -20 0 20 40 60 80 100 120 0 -2 -4 -60 140 -40 -20 0 TRANSIMPEDANCE (kΩ) BIAS CURRENT (µA) 60 80 100 120 140 4000 22 20 18 16 -60 -40 -20 0 20 40 60 80 100 120 140 3000 2000 1000 -60 -40 -20 0 TEMPERATURE (oC) 20 40 60 80 100 120 140 TEMPERATURE (oC) FIGURE 28. -INPUT BIAS CURRENT vs TEMPERATURE FIGURE 29. TRANSIMPEDANCE vs TEMPERATURE 74 25 +PSRR 72 REJECTION RATIO (dB) 125oC 55oC 20 ICC (mA) 40 FIGURE 27. +INPUT BIAS CURRENT vs TEMPERATURE FIGURE 26. INPUT OFFSET VOLTAGE vs TEMPERATURE 15 10 25oC 5 20 TEMPERATURE (oC) TEMPERATURE (oC) 3 4 5 6 7 70 68 -PSRR 66 64 62 CMRR 60 8 9 10 11 12 13 14 SUPPLY VOLTAGE (±V) FIGURE 30. SUPPLY CURRENT vs SUPPLY VOLTAGE 11 15 58 -100 -50 0 50 100 150 200 TEMPERATURE (oC) FIGURE 31. REJECTION RATIO vs TEMPERATURE 250 HA5023 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 4.0 30 +15V +10V +5V OUTPUT SWING (V) SUPPLY CURRENT (mA) 40 20 3.8 10 0 0 1 2 3 4 5 6 7 8 9 3.6 -60 10 11 12 13 14 15 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (oC) DISABLE INPUT VOLTAGE (V) FIGURE 32. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE FIGURE 33. OUTPUT SWING vs TEMPERATURE 30 1.2 VCC = ±15V 1.1 VIO (mV) VOUT (VP-P) 20 VCC = ±10V 1.0 10 0.9 VCC = ±4.5V 0.8 0 0.01 0.10 1.00 10.00 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (oC) LOAD RESISTANCE (kΩ) FIGURE 34. OUTPUT SWING vs LOAD RESISTANCE FIGURE 35. INPUT OFFSET VOLTAGE CHANGE BETWEEN CHANNELS vs TEMPERATURE -30 1.5 AV = +1 VOUT = 2VP-P SEPARATION (dB) ∆BIAS CURRENT (µA) -40 1.0 0.5 -50 -60 -70 0.0 -60 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (oC) FIGURE 36. INPUT BIAS CURRENT CHANGE BETWEEN CHANNELS vs TEMPERATURE 12 140 -80 0.1 1 FREQUENCY (MHz) 10 FIGURE 37. CHANNEL SEPARATION vs FREQUENCY 30 HA5023 Typical Performance Curves -20 -30 -40 -50 10 RL = 100Ω 1 0.1 0.01 180 0.001 135 90 45 -60 0 -70 -45 -80 -90 1 FREQUENCY (MHz) 10 FIGURE 38. DISABLE FEEDTHROUGH vs FREQUENCY 20 0.001 0.01 0.1 1 FREQUENCY (MHz) 10 RL = 400Ω 1 0.1 0.01 180 0.001 135 90 45 0 -45 -90 0.001 0.01 0.1 1 10 FREQUENCY (MHz) 100 -135 FIGURE 40. TRANSIMPEDENCE vs FREQUENCY 13 10 100 FIGURE 39. TRANSIMPEDANCE vs FREQUENCY PHASE ANGLE (DEGREES) 0.1 -135 PHASE ANGLE (DEGREES) DISABLE = 0V VIN = 5VP-P RF = 750Ω TRANSIMPEDANCE (MΩ) FEEDTHROUGH (dB) -10 TRANSIMPEDANCE (MΩ) 0 VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) HA5023 Die Characteristics SUBSTRATE POTENTIAL (Powered Up): V- DIE DIMENSIONS: PASSIVATION: 1650µm x 2540µm x 483µm Type: Nitride Thickness: 4kÅ ±0.4kÅ METALLIZATION: Type: Metal 1: AlCu (1%) Thickness: Metal 1: 8kÅ ±0.4kÅ TRANSISTOR COUNT: 124 Type: Metal 2: AlCu (1%) Thickness: Metal 2: 16kÅ ±0.8kÅ PROCESS: High Frequency Bipolar Dielectric Isolation Metallization Mask Layout HA5023 OUT NC V+ -IN1 +IN1 NC OUT2 NC V- +IN -IN All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com 14