EC-Centrifugalblowers-doubleinlet EN

D3G_englisch:Axial_D
30.04.2008
10:57
Seite 1
EC centrifugal blowers
dual inlet
The engineer’s choice
version 04/2008
D3G_englisch:Axial_D
30.04.2008
10:57
Seite 2
New EC centrifugal blowers dual inlet
Energy savings, convenient control and low noise
Cylindrical rotor fans in EC technology
Saving energy is becoming an ever increasingly important topic these days. Especially when it comes
to air-conditioning and ventilation technology, great potential savings can be achieved by using energyefficient fans. For this reason, motor and fan specialist ebm-papst Mulfingen has recognised the issue,
and has developed a complete series of dual-inlet, direct-driven cylindrical rotor fans with efficient EC
technology. Without changing the design of the unit, this allows a conversion from a conventional fan
with asynchronous motor to modern energy-saving technology.
The advantages of EC fans speak for themselves. Because the electronically commutated external rotor
motor is integrated within the forward curved impeller, the installation dimensions are reduced and
there is no longer any need for the commonly required belt drive between the motor attached on the
outside and the impeller. This reduces the fan dimensions always desirable for ventilation and
air-conditioning technology as well as the associated installation effort.
Furthermore, the electronically commutated motors are extremely quiet and operate at efficiencies of
up to 90 %. Thus they attain significantly higher values than most voltage-controlled asynchronous
motors, which have typical efficiencies of between 30 % and 60 %. At the same operating point, therefore, the power consumption of the EC fans is considerably less.
With integrated motor electronics, the EC fans can be easily speed controlled via a 0-10 V signal or by
the use of a potentiometer. As an option up to three air flow values can be programmed in "Constant
Flow" mode. This means that if the system resistance changes, for example due to polluted filters, the
fan keeps the programmed air flow by changing the speed automatically.
Depending on the motor type used, the double inlet fans with state-of-the-art EC technology cover
almost every conceivable application area. You can choose between eleven sizes with drive outputs
between 85 W and 3 kW. Thus a customised solution is available for virtually any application, including
compact air handling units, air curtains for doors and gates, fan coils, air heaters for factory buildings
or as a cooling fan for forced cooling of power converters, generators or telecommunications systems.
2
D3G_englisch:Axial_D
30.04.2008
10:57
Seite 3
Table of content
New EC centrifugal blowers dual inlet
2
Size 133
4
Size 146
6
Size 160
8
Size 180
10
Size 200
12
Size 225
14
Size 250
16
Size 283 (10
22
Size 318 (12
26
Size 404 (15
34
Size 454 (18
38
Electrical connections
40
Distributors, agencies and subsidiaries
46
3
D3G_englisch:Axial_D
30.04.2008
10:57
Seite 4
EC centrifugal blowers
dual inlet, Ø 133
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 40
50/60
1280
86
0,65
1~ 230
A
subject to alterations
Min. back pressure
M3G 055-CF
Max. current
draw(1)
D3G 133
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Galvanised
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 44
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
0
-25..+40
(1) Nominal data in operating point with maximum load
A
2
[Pa]
[in H O]
Curves
280
H1)
1,0
260
n
[rpm]
P1
[W]
I
[A]
LpA
[dB(A)]
ηtL
[%]
A
1
1280
86
0,65
60
—
A
2
1550
82
0,63
58
46
A
3
1825
62
0,48
54
53
A
4
2055
47
0,36
53
44
A
5
1270
83
0,63
59
—
A
6
1460
69
0,54
56
44
A
7
1720
51
0,39
53
53
A
8
1930
39
0,30
53
41
A
9
1110
53
0,41
55
—
A
10
1270
44
0,34
51
44
A
11
1440
30
0,23
48
51
A
12
1570
22
0,17
48
40
A
13
855
25
0,19
49
—
A
14
960
21
0,16
43
41
A
15
1070
15
0,12
39
40
A
16
1110
10
0,09
38
31
240
4
200
0,8
220
8
180
3
0,6
160
7
140
12
120
11
0,4
100
2
80
6
16
60
10
0,2
15
40
14
20
100
100
4
200
200
300
300
400
500
5 1
500 [CFM]
9
13
0
400
600
700
800
[m3/h]
D3G_englisch:Axial_D
30.04.2008
10:57
Seite 5
Mass of
centrifugal blower
– Technical features:
• Tach output
• Control input 0-10 VDC / PWM
• Locked-rotor protection
• Output 10 VDC max. 1.1 mA
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-1
Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 60950-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: EN 60335-1, CE
– Approvals: GOST; UL, VDE, CSA, CCC are applied for
Centrifugal blower
with flange
kg
D3G 133-BF03 -02
3,0
270
254
204
Ø5.5
Ø112
213
100
126
142
97
93.5
fe
btie
rau crew
sch f s
Ein pth o8 mm
De ax.
m
0
0+2
45
232
Brass lead tips
5
Electr. connection
p. 40
D3G_englisch:Axial_D
30.04.2008
10:57
Seite 6
EC centrifugal blowers
dual inlet, Ø 146
Frequency
Speed/rpm
Max. power
input(1)
Max. current
draw(1)
Min. back pressure
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 41
50/60
1740
171
1,30
Curve
Nominal voltage
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Galvanised
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 44
– Insulation class: "B"
– Mounting position: Shaft horizontal; rotor on top or rotor on bottom on request
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Nominal data
Type
Motor
D3G 146
M3G 074-CF
1~ 230
A
subject to alterations
0
-25..+60
(1) Nominal data in operating point with maximum load
A
2
[Pa]
[in H O]
Curves
n
[rpm]
P1
[W]
I
[A]
LpA
[dB(A)]
ηtL
[%]
A
1
1740
171
1,30
67
—
A
2
1960
169
1,20
65
49
A
3
2150
165
1,20
65
56
A
4
2410
166
1,20
66
55
A
5
1460
103
0,70
62
—
A
6
1650
102
0,80
60
46
A
7
1820
104
0,80
60
53
A
8
2020
102
0,70
61
52
A
9
1090
47
0,40
55
—
A
10
1220
46
0,40
56
41
A
11
1330
46
0,40
52
47
A
12
1480
46
0,40
53
44
1,5
400
4
1,0
300
3
8
200
7
0,5
2
12
6
100
11
10
0
100
200
6
J1)
200
9
400
300
400
600
5
500
800
600
1000
1
[CFM]
[m3/h]
D3G_englisch:Axial_D
30.04.2008
10:57
Seite 7
Mass of
centrifugal blower
– Technical features:
• Output 10 VDC max. 1.1 mA
• PFC (passive)
• Tach output
• Control input 0-10 VDC / PWM
• Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-1
Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 60950-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: EN 60335-1, EN 61800-5-1, EN 60950-1, CE
– Approvals: UL, CSA; CCC, GOST are applied for
Centrifugal blower
with flange
kg
D3G 146-AH50 -11
4,2
270
254
206
96
126
142
98
Ø117
219
100
Ø5.5
+20
350
Core-end sleeves
232
7
Electr. connection
p. 41
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 8
EC centrifugal blowers
dual inlet, Ø 160
subject to alterations
Min. back pressure
Perm. amb. temp.
Electr. connection
M3G 074-CF
Max. current
draw(1)
D3G 160
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Galvanised
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 44
– Insulation class: "B"
– Mounting position: Shaft horizontal; rotor on top or rotor on bottom on request
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
VAC
Hz
rpm
W
A
Pa
°C
p. 41
50/60
1390
154
1,20
1~ 230
A
0
-25..+60
(1) Nominal data in operating point with maximum load
2
A
1,0
[Pa]
[in H O]
Curves
4
0,75
200
3
160
7
80
2
0,25
12
11
6
40
10
9
0
100
200
8
200
300
400
400
600
500
800
5
600
1000
1
[CFM]
[m3/h]
P1
[W]
I
[A]
LpA
[dB(A)]
ηtL
[%]
1
1390
154
1,20
64
—
A
2
1440
129
1,00
61
53
A
3
1540
93
0,70
57
60
A
4
1590
63
0,50
56
47
A
5
1180
96
0,70
59
—
A
6
1220
79
0,60
56
52
A
7
1270
54
0,40
52
57
A
8
1310
37
0,30
51
44
A
9
860
40
0,30
51
—
A
10
890
34
0,30
47
45
A
11
910
24
0,20
43
45
A
12
930
18
0,20
42
31
0,5
8
n
[rpm]
A
240
120
J1)
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 9
Mass of
centrifugal blower
– Technical features:
• Output 10 VDC max. 1.1 mA
• PFC (passive)
• Tach output
• Control input 0-10 VDC / PWM
• Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-1
Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 60950-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: EN 60335-1, EN 61800-5-1, EN 60950-1, CE
– Approvals: UL, CSA; CCC, GOST are applied for
Centrifugal blower
with flange
kg
D3G 160-BF60 -11
5,5
270
254
226
Ø5.5
129
145
100,5
Ø130
241
103
102
400+20
Core-end sleeves
232
9
Electr. connection
p. 41
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 10
EC centrifugal blowers
dual inlet, Ø 180
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 41
50/60
1090
165
1,22
1~ 230
A
subject to alterations
Min. back pressure
M3G 074-CF
Max. current
draw(1)
D3G 180
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Galvanised
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 44
– Insulation class: "B"
– Mounting position: Shaft horizontal; rotor on top or rotor on bottom on request
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
0
-25..+60
(1) Nominal data in operating point with maximum load
2
A
1,00
[Pa]
[in H O]
Curves
250
J1)
4
0,75
200
3
150
P1
[W]
I
[A]
LpA
[dB(A)]
ηtL
[%]
A
1
1090
165
1,22
64
—
A
2
1200
155
1,15
62
54
A
3
1310
113
0,85
59
62
A
4
1400
74
0,55
56
53
A
5
925
101
0,75
60
—
A
6
1015
95
0,70
58
51
A
7
1090
67
0,50
54
61
A
8
1145
45
0,35
51
48
A
9
690
43
0,35
52
—
A
10
760
42
0,30
50
47
A
11
805
31
0,25
46
51
A
12
840
21
0,20
43
39
A
13
455
15
0,15
40
—
A
14
500
15
0,15
38
36
A
15
525
12
0,10
34
35
A
16
545
9
0,10
32
23
8
0,50
n
[rpm]
7
100
12
0,25
2
11
50
6
16
10
15
14
13
0
250
400
10
9
500
800
1
[CFM]
5
750
1200
1600
[m3/h]
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 11
Mass of
centrifugal blower
– Technical features:
• Output 10 VDC max. 1.1 mA
• PFC (passive)
• Tach output
• Control input 0-10 VDC / PWM
• Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-1
Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 60950-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: EN 60335-1, EN 61800-5-1, EN 60950-1, CE
– Approvals: UL, CSA; CCC, GOST are applied for
kg
D3G 180-AB62 -01
7,0
309
289
180
296
Ø7
600 +20
136
Ø149
333
132
133
90
168
188
Centrifugal blower
with flange
Core-end sleeves
255
11
Electr. connection
p. 41
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 12
EC centrifugal blowers
dual inlet, Ø 200
subject to alterations
Min. back pressure
Perm. amb. temp.
Electr. connection
M3G 084-FA
Max. current
draw(1)
D3G 200
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
VAC
Hz
rpm
W
A
Pa
°C
p. 42
50/60
1640
465
3,00
225
-25..+50
1~ 230
A
(1) Nominal data in operating point with maximum load
A
2
[Pa]
1,8 [in H O]
Curves
440
1,4
360
3
2
1,2
320
280
200
1,0
6
1
0,8
240
7
8
n
[rpm]
P1
[W]
I
[A]
LpA
[dB(A)]
A
1
1640
465
3,00
70
A
2
1665
402
2,60
68
A
3
1750
308
1,98
66
A
4
1825
225
1,48
66
A
5
1425
337
2,18
68
A
6
1425
251
1,62
65
A
7
1425
166
1,07
61
A
8
1425
107
0,70
61
A
9
950
100
0,65
56
A
10
950
74
0,48
53
A
11
950
49
0,32
50
A
12
950
32
0,21
50
A
13
475
12
0,08
37
A
14
475
9
0,06
34
A
15
475
6
0,04
32
A
16
475
4
0,03
32
1,6
4
400
K1)
160
0,6
5
120
11
12
0,4
10
80
0,2
40
9
16
0
15
200
400
12
14
13
400
600
800
800
1200
1000
1600
1200
2000
[CFM]
[m3/h]
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 13
Mass of
centrifugal blower
– Technical features:
• Output 10 VDC max. 1.1 mA
• PFC (passive)
• Alarm relay
• Control input 0-10 VDC / PWM
• Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: UL, CSA; CCC, GOST is applied for
kg
D3G 200-BB22 -71
9,4
341
321
180
327
Ø7
151
Ø167
371
141
146
90
180
200
Centrifugal blower
with flange
Core-end sleeves
800 +20
287
13
Electr. connection
p. 42
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 14
EC centrifugal blowers
dual inlet, Ø 225
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 42
50/60
1150
375
2,30
150
-25..+50
1~ 230
A
subject to alterations
Min. back pressure
M3G 084-FA
Max. current
draw(1)
D3G 225
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
(1) Nominal data in operating point with maximum load
A
1,2
2
[Pa]
[in H O]
Curves
320
4
280
1,0
240
0,8
7
160
0,6
LpA
[dB(A)]
1150
375
2,30
67
2
1210
320
2,07
66
A
3
1275
260
1,69
64
A
4
1345
190
1,26
62
A
5
1050
278
1,69
65
A
6
1050
209
1,35
62
A
7
1050
145
0,94
59
A
8
1050
90
0,60
56
A
9
700
82
0,50
53
A
10
700
62
0,40
51
A
11
700
43
0,28
48
A
12
700
27
0,18
45
A
13
350
10
0,06
34
A
14
350
8
0,05
32
A
15
350
5
0,03
31
A
16
350
3
0,02
28
5
0,4
120
80
12
11
10
0,2
9
40
16
0
15
200
400
14
I
[A]
1
6
1
P1
[W]
A
2
8
n
[rpm]
A
3
200
K1)
14
13
400
600
800
800
1200
1000
1600
1200
2000
1400
[CFM]
2400
[m3/h]
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 15
Mass of
centrifugal blower
– Technical features:
• Output 10 VDC max. 1.1 mA
• PFC (passive)
• Alarm relay
• Control input 0-10 VDC / PWM
• Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 225-CC14 -71
10,8
387
367
180
327
Ø7
151
Ø194
370
250
180
284
304
141
158
20
0+
80
Core-end sleeves
333
15
Electr. connection
p. 42
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 16
EC centrifugal blowers
dual inlet, Ø 250
Frequency
Speed/rpm
Max. power
input(1)
Max. current
draw(1)
Min. back pressure
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 42
50/60
1085
450
2,80
100
-25..+40
Curve
Nominal voltage
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Nominal data
Type
Motor
D3G 250
M3G 084-GF
1~ 230
A
subject to alterations
(1) Nominal data in operating point with maximum load
2
A
1,4
[Pa]
[in H O]
Curves
360
4
1,2
320
3
0,8
200
1,0
280
240
8
7
2
0,6
160
6
12
120
0,4
11
16
5
0,2
15
9
14
40
13
0
500
500
1000
1000
1500
1500
2000
2500
[CFM]
[m3/h]
n
[rpm]
P1
[W]
I
[A]
LpA
[dB(A)]
A
1
1085
450
2,80
71
A
2
1125
401
2,55
69
A
3
1175
346
2,20
67
A
4
1285
232
1,50
65
A
5
1000
346
2,21
69
A
6
1000
282
1,80
66
A
7
1000
213
1,36
63
A
8
1000
110
0,71
58
A
9
800
177
1,13
63
A
10
800
145
0,92
60
A
11
800
109
0,70
56
A
12
800
56
0,37
52
A
13
600
75
0,48
55
A
14
600
61
0,39
51
A
15
600
46
0,29
48
A
16
600
24
0,15
44
1
10
80
16
K1)
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 17
Mass of
centrifugal blower
– Technical features:
• Output 10 VDC max. 1.1 mA
• PFC (passive)
• Alarm relay
• Control input 0-10 VDC / PWM
• Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: EN 61800-5-1, CE
– Approvals: UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 250-ED01 -71
12,0
349
328
180
387
194
Ø7
173
Ø200
392
167
90
190
198
218
329
Core-end sleeves
800
298
+2
0
17
Electr. connection
p. 42
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 18
EC centrifugal blowers
dual inlet, Ø 250
Frequency
Speed/rpm
Max. power
input(1)
Max. current
draw(1)
Min. back pressure
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 43
50/60
1250
720
3,20
100
-25..+40
Curve
Nominal voltage
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Nominal data
Type
Motor
D3G 250
M3G 112-EA
1~ 230
A
subject to alterations
(1) Nominal data in operating point with maximum load
2
A
4
1,4
[Pa]
[in H O]
Curves
360
1,2
3
280
160
1,0
0,8
7
2
12
120
0,4
11
0,2
16
40
9
15
14
13
0
500
500
18
1000
1000
1500
1500
2000
2500
[CFM]
3000
[m3/h]
I
[A]
LwA
[dB(A)]
1
1250
720
3,20
83
2
1305
608
2,77
81
A
3
1345
516
2,37
79
A
4
1395
383
1,79
75
A
5
1200
576
2,61
82
A
6
1200
472
2,15
79
A
7
1200
366
1,68
76
A
8
1200
243
1,13
71
A
9
850
205
0,93
73
A
10
850
168
0,76
70
A
11
850
130
0,60
67
A
12
850
86
0,40
62
A
13
500
42
0,19
59
A
14
500
34
0,16
55
A
15
500
27
0,12
53
A
16
500
18
0,08
49
1
5
10
80
P1
[W]
A
6
0,6
200
8
n
[rpm]
A
320
240
L3)
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 19
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (active)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-4
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 250-EE51 -11
14,2
349
328
180
387
194
Ø7
173
Ø200
392
165
90
190
198
218
329
Core-end sleeves
80
0+
298
20
19
Electr. connection
p. 43
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 20
EC centrifugal blowers
dual inlet, Ø 250
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 44
50/60
1500
1000
1,70
180
-25..+40
3~ 400
A
subject to alterations
Min. back pressure
M3G 112-GA
Max. current
draw(1)
D3G 250
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
(1) Nominal data in operating point with maximum load
n
[rpm]
2
A
2,0
[Pa]
[in H O]
Curves
500
1,6
4
400
3
1,2
8
300
0,8
7
200
12
2
11
6
0,4
100
10
16
15
14
0
500
500
20
L4)
1000
1000
1500
1500
2000
2500
2000
3000
3500
[CFM]
[m3/h]
P1
[W]
I
[A]
LwA
[dB(A)]
A
1
---
---
---
---
A
2
1500
1000
1,70
86
A
3
1570
874
1,39
83
A
4
1635
700
1,15
81
A
5
---
---
---
---
A
6
1280
599
1,01
82
A
7
1320
501
0,89
78
A
8
1365
397
0,76
76
A
9
---
---
---
---
A
10
990
286
0,57
75
A
11
1010
239
0,49
72
A
12
1035
185
0,40
69
A
13
---
---
---
---
A
14
650
92
0,23
64
A
15
655
80
0,21
61
A
16
670
66
0,19
58
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 21
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (passive)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: VDE, UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 250-EF41 -01
15,8
349
328
180
387
194
Ø7
173
Ø200
392
165
90
190
198
218
329
Core-end sleeves
298
80
0+
20
21
Electr. connection
p. 44
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 22
EC centrifugal blowers
dual inlet, Ø 283 (10)
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 43
50/60
1030
750
3,40
150
-25..+40
1~ 230
A
subject to alterations
Min. back pressure
M3G 112-GA
Max. current
draw(1)
D3G 283
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
(1) Nominal data in operating point with maximum load
n
[rpm]
2
A
1,4
[Pa]
[in H O]
Curves
360
4
1,2
280
160
1,0
0,8
7
2
12
120
6
0,4
11
0,2
16
15
40
14
0
500
500
22
1000
1000
1500
1500
2000
2500
2000
3000
3500
[CFM]
[m3/h]
LwA
[dB(A)]
1
---
---
---
---
2
1030
750
3,40
82
A
3
1100
575
2,61
78
A
4
1160
378
1,76
74
A
5
---
---
---
---
A
6
880
458
2,11
78
A
7
925
326
1,57
74
A
8
955
209
1,22
69
A
9
---
---
---
---
A
10
675
209
0,99
71
A
11
695
150
0,74
67
A
12
715
102
0,57
61
A
13
---
---
---
---
A
14
435
68
0,41
59
A
15
445
52
0,32
53
A
16
460
40
0,24
50
80
10
I
[A]
A
8
0,6
200
3
P1
[W]
A
320
240
L3)
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 23
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (active)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-4
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 283-AB32 -11
18,2
386
359
437
Ø9
196
444
Ø225
289
311
350
168
215
Core-end
sleeves
800
+20
326
23
Electr. connection
p. 43
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 24
EC centrifugal blowers
dual inlet, Ø 283 (10)
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 44
50/60
1150
1000
1,80
200
-25..+40
3~ 400
A
subject to alterations
Min. back pressure
M3G 112-GA
Max. current
draw(1)
D3G 283
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
(1) Nominal data in operating point with maximum load
n
[rpm]
2
2,0
[Pa]
A
4
1,6
400
[in H O]
Curves
500
L4)
3
P1
[W]
I
[A]
LwA
[dB(A)]
A
1
---
---
---
---
A
2
1150
1000
1,80
85
A
3
1260
888
1,44
83
A
4
1385
566
0,97
81
A
5
---
---
---
---
A
6
1020
681
1,14
81
A
7
1080
528
0,93
79
A
8
1160
342
0,67
76
A
9
---
---
---
---
A
10
805
341
0,66
75
A
11
840
258
0,52
72
A
12
885
162
0,36
68
A
13
---
---
---
---
A
14
540
108
0,26
64
A
15
555
83
0,22
62
A
16
575
57
0,18
59
300
1,2
8
200
0,8
7
2
12
11
0,4
100
6
10
16
15
14
0
500
1000
24
1000
1500
2000
2000
3000
2500
4000
[CFM]
[m3/h]
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 25
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (passive)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: VDE, UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 283-AB37 -01
18,2
386
359
437
Ø9
196
444
Ø225
289
311
350
168
215
Core-end
sleeves
800
+20
326
25
Electr. connection
p. 44
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 26
EC centrifugal blowers
dual inlet, Ø 318 (12)
Frequency
Speed/rpm
Max. power
input(1)
Max. current
draw(1)
Min. back pressure
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 43
50/60
960
750
3,40
260
-25..+40
Curve
Nominal voltage
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Nominal data
Type
Motor
D3G 318
M3G 112-GA
1~ 230
A
subject to alterations
(1) Nominal data in operating point with maximum load
A
2
[Pa]
1,6 [in H O]
Curves
400
200
150
1,2
1,0
0,8
250
3
8
7
0,6
300
1,4
4
350
12
0,4
10
16
0,2
50
15
14
0
500
500
26
1000
1000
1500
1500
2000
2500
2000
3000
3500
[CFM]
4000
[m3/h]
n
[rpm]
P1
[W]
I
[A]
LwA
[dB(A)]
---
A
1
---
---
---
A
2
---
---
---
---
A
3
960
750
3,40
78
A
4
1050
548
2,49
74
A
5
---
---
---
---
A
6
780
563
2,56
78
A
7
830
450
2,07
74
A
8
885
297
1,39
70
A
9
---
---
---
---
A
10
610
262
1,22
71
A
11
630
205
0,97
67
A
12
660
140
0,73
63
A
13
---
---
---
---
A
14
400
82
0,46
59
A
15
410
66
0,37
55
A
16
425
50
0,28
51
6
11
100
L3)
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 27
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (active)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-4
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 318-AA37 -11
20,8
369
335
509
Ø9
232
524
Ø256
357
402
340
204
245
Core-end sleeves
+20
800
309
27
Electr. connection
p. 43
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 28
EC centrifugal blowers
dual inlet, Ø 318 (12)
subject to alterations
Min. back pressure
Perm. amb. temp.
Electr. connection
M3G 112-GA
Max. current
draw(1)
D3G 318
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
VAC
Hz
rpm
W
A
Pa
°C
p. 44
50/60
880
1000
1,80
100
-25..+40
3~ 400
A
(1) Nominal data in operating point with maximum load
n
[rpm]
2
1,6
[Pa]
300
1,0
150
7
12
0,4
11
100
6
0,2
15
10
14
0
500
1000
28
LwA
[dB(A)]
1
---
---
---
---
A
2
880
1000
1,80
83
A
3
970
797
1,31
79
A
4
1065
568
0,99
75
A
5
---
---
---
---
A
6
775
635
1,08
79
A
7
840
487
0,88
75
A
8
905
335
0,66
71
A
9
---
---
---
---
A
10
620
323
0,64
73
A
11
660
240
0,50
69
A
12
695
158
0,35
64
A
13
---
---
---
---
A
14
420
105
0,26
62
A
15
440
78
0,21
57
A
16
455
55
0,18
53
2
16
50
I
[A]
A
3
0,6
200
0,8
8
250
P1
[W]
4
1,4
350
A
1,2
400
1,8 [in H O]
Curves
450
L4)
1000
1500
2000
2000
3000
2500
4000
[CFM]
5000 [m /h]
3
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 29
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (passive)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: VDE, UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 318-AA35 -01
20,8
369
335
509
Ø9
232
524
Ø256
357
402
340
204
245
Core-end sleeves
+20
800
309
29
Electr. connection
p. 44
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 30
EC centrifugal blowers
dual inlet, Ø 318 (12)
subject to alterations
Min. back pressure
Perm. amb. temp.
Electr. connection
M3G 112-GA
Max. current
draw(1)
D3G 318
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
VAC
Hz
rpm
W
A
Pa
°C
p. 43
50/60
900
700
3,20
250
-25..+40
1~ 230
A
(1) Nominal data in operating point with maximum load
2
A
1,4
[Pa]
[in H O]
Curves
350
1,0
250
1,2
4
300
3
0,8
8
200
0,6
12
0,4
100
6
11
10
16
0,2
50
15
14
0
500
1000
30
1000
1500
2000
2000
3000
2500
4000
[CFM]
[m3/h]
n
[rpm]
P1
[W]
I
[A]
LwA
[dB(A)]
---
A
1
---
---
---
A
2
---
---
---
---
A
3
900
700
3,20
75
A
4
970
529
2,42
73
A
5
---
---
---
---
A
6
740
562
2,55
75
A
7
780
434
1,99
71
A
8
815
328
1,58
69
A
9
---
---
---
---
A
10
575
267
1,24
69
A
11
600
202
0,94
64
A
12
620
148
0,72
61
A
13
---
---
---
---
A
14
380
82
0,44
57
A
15
390
65
0,34
52
A
16
400
51
0,27
49
7
150
L3)
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 31
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (active)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-4
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 318-BB34 -11
22,6
446
421
509
245
232
Ø256
524
340
357
402
204
Ø9
Core-end sleeves
800+20
386
31
Electr. connection
p. 43
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 32
EC centrifugal blowers
dual inlet, Ø 318 (12)
subject to alterations
Min. back pressure
Perm. amb. temp.
Electr. connection
M3G 112-GA
Max. current
draw(1)
D3G 318
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
VAC
Hz
rpm
W
A
Pa
°C
p. 44
50/60
880
1000
1,70
150
-25..+40
3~ 400
A
(1) Nominal data in operating point with maximum load
n
[rpm]
2
[Pa]
A
1,2
300
1,4
4
350
3
150
0,8
12
---
---
---
---
2
880
1000
1,70
62
A
3
960
813
1,36
62
A
4
1065
554
0,97
62
A
5
---
---
---
---
A
6
770
645
1,10
77
A
7
830
505
0,93
73
A
8
900
332
0,65
70
A
9
---
---
---
---
A
10
615
329
0,65
71
A
11
650
248
0,51
66
A
12
690
157
0,35
63
A
13
---
---
---
---
A
14
420
108
0,26
60
A
15
435
82
0,22
55
A
16
450
56
0,18
51
2
0,4
6
50
0,2
16
10
15
14
0
500
1000
32
1000
1500
2000
2000
3000
2500
4000
3000
[CFM]
5000
[m3/h]
LwA
[dB(A)]
1
11
100
I
[A]
A
7
0,6
200
1,0
8
250
P1
[W]
A
1,6
400
1,8 [in H O]
Curves
450
L4)
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 33
Line undervoltage detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (passive)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: VDE, UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 318-BB35 -01
22,4
446
421
509
245
232
Ø256
524
340
357
402
204
Ø9
Core-end sleeves
800+20
386
33
Electr. connection
p. 44
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 34
EC centrifugal blowers
dual inlet, Ø 404 (15)
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 45
50/60
1000
3000
4,80
300
-25..+40
3~ 400
A
subject to alterations
Min. back pressure
M3G 150-NA
Max. current
draw(1)
D3G 404
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "F"
– Mounting position: Shaft horizontal
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
(1) Nominal data in operating point with maximum load
2
2,8
4
2,4
[Pa]
500
A
3
2,0
600
[in H O]
Curves
700
2
300
1,6
8
7
6
1,2
400
1
12
5
10
9
16
15
0,4
100
11
0,8
200
14
13
0
1000
2000
34
M1)
2000
3000
4000
4000
6000
5000
8000
[CFM]
[m3/h]
n
[rpm]
P1
[W]
I
[A]
LwA
[dB(A)]
A
1
1000
3000
4,80
91
A
2
1065
2647
4,00
89
A
3
1120
2116
3,21
86
A
4
1180
1341
2,06
83
A
5
900
2108
3,18
88
A
6
900
1603
2,42
85
A
7
900
1095
1,66
81
A
8
900
596
0,92
77
A
9
700
992
1,50
81
A
10
700
754
1,14
77
A
11
700
515
0,78
74
A
12
700
281
0,43
71
A
13
500
361
0,55
72
A
14
500
275
0,42
69
A
15
500
188
0,29
65
A
16
500
102
0,16
61
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 35
Line undervoltage / phase failure detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (passive)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: VDE, UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 404-AA02 -03
52,9
422
400
370
125
583
Ø8
125
429
454
Ø309
274
531
641
406
255
273
80
0
+2
0
45.5
Ø10
46.5
460
Core-end sleeves
374
402
432
35
Electr. connection
p. 45
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 36
EC centrifugal blowers
dual inlet, Ø 404 (15)
Perm. amb. temp.
Electr. connection
VAC
Hz
rpm
W
A
Pa
°C
p. 45
50/60
1000
3000
4,80
375
-25..+40
3~ 400
A
subject to alterations
Min. back pressure
M3G 150-NA
Max. current
draw(1)
D3G 404
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "F"
– Mounting position: Shaft horizontal
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
(1) Nominal data in operating point with maximum load
2
A
2,8
[Pa]
[in H O]
Curves
700
4
400
2,0
2
1,6
500
2,4
3
600
M1)
n
[rpm]
P1
[W]
I
[A]
LwA
[dB(A)]
A
1
1000
3000
4,80
89
A
2
1055
2705
4,12
86
A
3
1125
2007
3,06
84
A
4
1180
1407
2,16
84
A
5
800
1445
2,20
82
A
6
800
1152
1,78
79
A
7
800
682
1,10
75
A
8
800
447
0,79
74
A
9
650
787
1,25
76
A
10
650
623
1,02
74
A
11
650
376
0,69
69
A
12
650
259
0,51
69
A
13
500
360
0,69
70
A
14
500
294
0,57
67
A
15
500
186
0,39
64
A
16
500
133
0,30
63
1
8
7
1,2
300
6
5
12
0,8
200
11
10
9
16
15
13
0
1000
2000
36
14
0,4
100
2000
3000
4000
4000
6000
5000
8000
[CFM]
[m3/h]
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 37
Line undervoltage / phase failure detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (passive)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: VDE, UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 404-BB02 -03
56,5
523
500
470
375
125
583
Ø8
125
429
454
Ø309
274
531
641
406
255
273
80
0
+2
0
45.5
Ø 10
46.5
460
Core-end sleeves
474
502
532
37
Electr. connection
p. 45
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 38
EC centrifugal blowers
dual inlet, Ø 454 (18)
subject to alterations
Min. back pressure
Perm. amb. temp.
Electr. connection
M3G 150-NA
Max. current
draw(1)
D3G 454
Max. power
input(1)
Motor
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Housing: Galvanised sheet steel
Impeller: Galvanised sheet steel
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "F"
– Mounting position: Shaft horizontal
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
VAC
Hz
rpm
W
A
Pa
°C
p. 45
50/60
660
2900
4,50
150
-25..+40
3~ 400
A
(1) Nominal data in operating point with maximum load
n
[rpm]
2
[Pa]
A
2,0
500
2,2 [in H O]
Curves
550
1,6
400
1,8
4
450
1,4
1,2
250
3
7
1,0
300
P1
[W]
I
[A]
LwA
[dB(A)]
A
1
---
---
---
---
A
2
660
2900
4,50
89
A
3
715
2414
4,20
85
A
4
790
1759
3,20
81
A
5
---
---
---
---
A
6
615
2225
3,38
86
A
7
665
1813
2,76
83
A
8
720
1251
1,91
78
A
9
---
---
---
---
A
10
500
1123
1,73
81
A
11
525
875
1,37
77
A
12
555
574
0,95
72
A
13
---
---
---
---
A
14
355
400
0,74
72
A
15
365
308
0,60
67
A
16
385
209
0,43
62
8
350
M1)
11
0,6
150
0,8
12
200
2
6
16
0,4
100
10
50
0,2
15
14
0
1000
2000
38
2000
3000
4000
4000
6000
5000
8000
6000
7000 [CFM]
10000
12000 [m /h]
3
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 39
Line undervoltage / phase failure detection
Motor current limitation
Over-temperature protected electronics / motor
Locked-rotor protection
Soft start
Mass of
centrifugal blower
– Technical features:
•
• PFC (passive)
•
• Control input 0-10 VDC / PWM
•
• Output 10 VDC max. 10 mA
•
• Alarm relay
•
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1
– Cable exit: Variable
– Protection class: I
– Product conforming to standards: CE
– Approvals: VDE, UL, CSA; CCC, GOST is applied for
Centrifugal blower
with flange
kg
D3G 454-AA07 -03
61,5
478
455
423
125
700
Ø8
125
395
505
532
Ø381
0
0+2
80
331
641
773
480
310
321
56.5
Ø10
56.5
553
Core-end sleeves
428
462
498
39
Electr. connection
p. 45
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 40
Electrical connections EC
H1) EC motors (size 055, line-fed)
Notes on various control possibilities and their applications
Umin = 15 V
Imax =
10 mA
L
brown
N
blue
Mains
50/60 Hz
+
-
PE
green/yellow
+
Voltage output
+10 V max. 1.1 mA
U
PWM
-
10 K
red
12 V
Lin/PWM control input
0-10 VDC / PWM
yellow
Speed setting
PWM 1 - 10 kHz
Speed setting
with variable
resistance
Full speed
Speed setting
1 V - 10 V
100% PWM -> n=max
approx. 10% PWM -> n=min
< 10% PWM -> n=0
start up at > 1.4 V
Counter
GND
blue
Tach output
1 pulse per revolution
Controller
white
10 V -> n=max
approx. 1 V -> n=min
< 1 V -> n=0
Alarm
start up at > 1.4 V
Speed display
Customer circuit
1 μF
Isink max. 10 mA
680 Ω
47 V
Connection
N
PE
+10 V
0-10 V
PWM
GND
Tach
Line 2
L
Line 1
Fan
brown
blue
green/yellow
red
yellow
blue
white
Line
Connection Colour Assignment / function
Line
1
L
brown
Mains 50/60 Hz, phase
2
N
blue
Mains 50/60 Hz, neutral
0-10 V / PWM yellow
Control input (Impedance 100 kΩ)
PE
green/yel
Protective earth
GND
blue
GND
Tach
white
Tach output: 1 pulse per revolution
40
Connection Colour Assignment / function
+10 V
red
Voltage output +10 V max. 1.1 mA
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 41
J1) EC motors (size 074, line-fed)
Notes on various control possibilities and their applications
Umin = 15 V
Imax =
10 mA
L
black
N
blue
Mains
50/60 Hz
+
-
PE
green/yellow
+
Voltage output
+10 V max. 1.1 mA
U
PWM
-
10 K
red
12 V
Lin/PWM control input
0-10 VDC / PWM
yellow
Speed setting
PWM 1 - 10 kHz
Speed setting
with variable
resistance
Full speed
Speed setting
1 V - 10 V
100% PWM -> n=max
approx. 10% PWM -> n=min
< 10% PWM -> n=0
start up at > 1.4 V
Counter
GND
blue
Tach output
1 pulse per revolution
Controller
white
10 V -> n=max
approx. 1 V -> n=min
< 1 V -> n=0
Alarm
start up at > 1.4 V
Speed display
Customer circuit
1 μF
Isink max. 10 mA
680 Ω
47 V
Connection
N
PE
+10 V
0-10 V
PWM
GND
Tach
Line 2
L
Line 1
Fan
black
blue
green/yellow
red
yellow
blue
white
Line
Connection Colour Assignment / function
Line
Connection Colour Assignment / function
1
L
black
Mains 50/60 Hz, phase
2
+10 V
N
blue
Mains 50/60 Hz, neutral
0-10 V / PWM yellow
PE
green/yel
Protective earth
GND
blue
GND
Tach
white
Tach output: 1 pulse per revolution
red
Voltage output +10 V max. 1.1 mA
Control input (Impedance 100 kΩ)
41
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 42
Electrical connections EC
K1) EC motors (size 084, line-fed)
Notes on various control possibilities and their applications
Umin = 15 V
Imax =
10 mA
Mains
50/60 Hz
U
-
10 K
+
-
NC
white1
COM
white2
Voltage output
red
+10 V
max. 1.1 mA
+
PWM
L
black
N
blue
PE
green/yellow
12 V
Alarm relay:
Break for failure
(2 A, 250 VAC, AC1)
Lin/PWM control input
yellow
0-10 VDC /
PWM
1 μF
GND
blue
Speed setting
PWM 1 - 10 kHz
Speed setting
with variable
resistance
Full speed
Speed setting
1 V - 10 V
100% PWM -> n=max
approx. 10% PWM -> n=min
< 10% PWM -> n=0
10 V -> n=max
approx. 1 V -> n=min
< 1 V -> n=0
start up at > 1.4 V
start up at > 1.4 V
Customer circuit
Connection
+10 V
0-10 V
PWM
GND
green/yellow white1
COM
blue
Line 2
NC
N
black
PE
L
Line 1
Fan
white2
red
yellow
blue
Line
Connection Colour Assignment / function
Line
1
L
black
Mains 50/60 Hz, phase
2
N
blue
Mains 50/60 Hz, neutral
0-10 V / PWM yellow
Control input (Impedance 100 kΩ)
PE
green/yel
Protective earth
GND
GND
NC
white1
Alarm relay, break for failure
COM
white2
Alarm relay, COMMON
42
Connection Colour Assignment / function
+10 V
red
blue
Voltage output +10 V max. 1.1 mA
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 43
L3) EC motors (size 112, single-phase mains-powered)
Full
speed
Speed
setting
8
8
PE
2
PE1
1-10 V
11
N
12
3
10 V -> n = max
1 V -> n = min
<1 V -> n = 0
L
4
AC1
P
AC2
N
11
COM
5
A1
10 A (T)
14
A2
NC
6
0-10 V
0-10 V
8
Speed setting
with
potentiometer
47 K
P
47 K
470 nF
10
10 V
10 V
11
11
10
Imax=10 mA
GND
12
0V
8
10 K
12
Customer circuit
Connection
Fan
N
L
COM
NC
0-10 V
P
+10 V
GND
Line 2
PE
Line 1
green/yellow
blue
black
white1
white2
yellow
orange
red
blue
Line
No.
Connection Colour
Assignment / function
1
2
PE
green/yellow
Protective earth
1
3
N
blue
Mains 50/60 Hz, neutral
1
4
L
black
Mains 50/60 Hz, phase
1
5
COM
white1
Alarm relay, COMMON (2A, max. 250 VAC, min. 10 mA, AC1)
1
6
NC
white2
Alarm relay, break for failure
2
8
0-10 V
yellow
Control input (Impedance 100 kΩ), SELV
2
10
P
orange
not designated
2
11
+10 V
red
Voltage output 10 VDC (+/- 3%), max. 10 mA, supply voltage for external units (e.g. potentiometer), SELV
2
12
GND
blue
GND, SELV
43
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 44
Electrical connections EC
L4) EC motors (size 112, three-phase mains-powered)
Full
speed
Speed
setting
8
8
PE
2
PE1
1-10 V
L1
12
11
3
10 V -> n = max
1 V -> n = min
<1 V -> n = 0
P
AC1
AC2
AC3
L2
4
L3
N
11
A1
A2
COM
6
14
5
NC
7
Speed setting
with
potentiometer
0-10 V
0-10 V
8
47 K
P
47 K
470 nF
10
11
+10 V
10 V
11
Imax=10 mA
GND
10 K
0V
12
8
12
Customer circuit
Connection
Fan
L3
COM
NC
0-10 V
P
+10 V
GND
green/yellow black
Line 2
L2
L1
PE
Line 1
black
black
white1
white2
yellow
orange
red
blue
Line
No.
Connection Colour
Assignment / function
1
2
PE
green/yellow
Protective earth
1
3
L1
black
Mains 50/60 Hz, phase
1
4
L2
black
Mains 50/60 Hz, phase
1
5
L3
black
Mains 50/60 Hz, phase
1
6
COM
white1
Alarm relay, COMMON (2A, max. 250 VAC, min. 10 mA, AC1)
1
7
NC
white2
Alarm relay, break for failure
2
8
0-10 V
yellow
Control input (Impedance 100 kΩ), SELV
2
10
P
orange
not designated
2
11
+10 V
red
Voltage output 10 VDC (+/- 3%), max. 10 mA, supply voltage for external units (e.g. potentiometer), SELV
2
12
GND
blue
GND, SELV
44
D3G_englisch:Axial_D
30.04.2008
10:58
Seite 45
M1) EC motors (size 150, three-phase mains-powered)
Full
speed
Speed
setting
PE
2
PE1
8
8
L1
1-10 V
3
12
11
P
AC1
AC2
AC3
L2
10 V -> n = max
1 V -> n = min
<1 V -> n = 0
4
L3
N
11
A1
A2
COM
6
14
5
NC
7
0-10 V
Speed setting
with
potentiometer
0-10 V
8
47 K
47 K
2,2 μF
+10 V
10 V
11
11
33
Imax=10 mA
GND
12
10 K
0V
RSA
8
RSA
13
RSB
RSB
14
12
Customer circuit
Connection
Fan
L3
COM
NC
0-10 V
+10 V
GND
RSA
RSB
green/yellow black
Line 2
L2
L1
PE
Line 1
black
black
white1
white2
yellow
red
blue
orange
black
Line
No.
Connection Colour
Assignment / function
1
2
PE
green/yellow
Protective earth
1
3
L1
black
Mains 50/60 Hz, phase
1
4
L2
black
Mains 50/60 Hz, phase
1
5
L3
black
Mains 50/60 Hz, phase
1
6
COM
white1
Alarm relay, COMMON (2A, max. 250 VAC, min. 10 mA, AC1)
1
7
NC
white2
Alarm relay, break for failure
2
8
0-10 V
yellow
Control input (Impedance 100 kΩ), SELV
2
11
+10 V
red
Voltage output 10 VDC (+/- 3%), max. 10 mA, supply voltage for external units (e.g. potentiometer), SELV
2
12
GND
blue
GND, SELV
2
13
RSA
orange
RS485 interface for ebmBUS; RSA, SELV
2
14
RSB
black
RS485 interface for ebmBUS; RSB, SELV
45
D3G_englisch:Axial_D
30.04.2008
10:59
fan agent
compact fan agent
Seite 46
Distributors, agencies and subsidiaries
motor specialist
motor agent
Germany
ebm-papst
Mulfingen GmbH & Co. KG
ebm-papst
St. Georgen GmbH & Co. KG
ebm-papst
Landshut GmbH
Bachmühle 2
D-74673 Mulfingen
Phone +49 (0) 79 38 / 81-0
Fax +49 (0) 79 38 / 81-110
[email protected]
Hermann-Papst-Straße 1
D-78112 St. Georgen
Phone +49 (0) 77 24 / 81-0
Fax +49 (0) 77 24 / 81-13 09
[email protected]
Hofmark-Aich-Straße 25
D-84030 Landshut
Phone +49 (0) 8 71 / 707-0
Fax +49 (0) 8 71 / 707-465
[email protected]
www.ebmpapst.com
www.ebmpapst.com
www.ebmpapst.com
Agencies
Berlin
Dipl.-Ing. (TH) Jens Duchow
Händelstraße 7
D-16341 Panketal
Phone +49 (0) 30 / 94 41 49 62
Fax +49 (0) 30 / 94 41 49 63
[email protected]
Dortmund
Dipl.-Ing. (FH) Hans-Joachim Pundt
Auf den Steinern 3
D-59519 Möhnesee-Völlinghausen
Phone +49 (0) 29 25 / 80 04 07
Fax +49 (0) 29 25 / 80 04 08
[email protected]
Frankfurt
Dipl.-Ing. Christian Kleffmann
Dr. Hermann-Krause Straße 23
D-63452 Hanau
Phone +49 (0) 61 81 / 18 98 12
Fax +49 (0) 61 81 / 18 98 13
[email protected]
Halle
Dipl.-Ing. (TU) Michael Hanning
Lerchenweg 4
D-06120 Lieskau
Phone +49 (0) 3 45 / 5 51 24 56
Fax +49 (0) 3 45 / 5 51 24 57
[email protected]
Hamburg
Ingenieurbüro Breuell GmbH
Dirk Kahl
Elektroingenieur
Grützmühlenweg 40
D-22339 Hamburg
Phone +49 (0) 40 / 53 80 92 10
Fax +49 (0) 40 / 53 80 92 84
[email protected]
Kassel
Dipl.-Ing. (FH) Ralph Brück
Hoherainstraße 38
D-35075 Gladenbach
Phone +49 (0) 64 62 / 40 71 10
Fax +49 (0) 64 62 / 40 71 11
[email protected]
46
Koblenz
Winfried Schaefer
Hinter der Kirch 10
D-56767 Uersfeld
Phone +49 (0) 26 57 / 16 96
Fax +49 (0) 26 57 / 16 76
[email protected]
Munich
Dipl.-Wirt.-Ing. (FH) Jens Peter
Steinbergweg 6
D-82285 Hattenhofen
Phone +49 (0) 81 45 / 80 92 25
Fax +49 (0) 81 45 / 80 92 26
[email protected]
Nuremberg
Friedrich Klein
Adlerstraße 49/1
D-73540 Heubach
Phone +49 (0) 71 73 / 49 83
Fax +49 (0) 71 73 / 80 53
[email protected]
Offenburg
Dipl.-Ing (FH) Ralf Braun
Hubeneck 21
D-77704 Oberkirch
Phone +49 (0) 78 02 / 98 22 52
Fax +49 (0) 78 02 / 98 22 53
[email protected]
Stuttgart
Dipl.-Ing. (FH) Rudi Weinmann
Hindenburgstraße 100/1
D-73207 Plochingen
Phone +49 (0) 71 53 / 92 89 80
Fax +49 (0) 71 53 / 92 89 81
[email protected]
Ulm
Günter Wilhelm
Allgäuer Straße 7
D-89269 Vöhringen
Phone +49 (0) 73 06 / 92 46 08
Fax +49 (0) 73 06 / 92 46 48
[email protected]
Distributors
Frankfurt
R.E.D. Handelsgesellschaft mbH
Gutenbergstraße 3
D-63110 Rodgau - Jügesheim
Phone +49 (0) 61 06 / 84 10
Fax +49 (0) 61 06 / 84 11 11
[email protected]
www.red-elektromechanik.de
Hamburg
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 40
D-22339 Hamburg
Phone +49 (0) 40 / 53 80 92 20
Fax +49 (0) 40 / 53 80 92 84
[email protected]
Munich
A. Schweiger GmbH
Ohmstraße 1
D-82054 Sauerlach
Phone +49 (0) 81 04 / 8 97 0
Fax +49 (0) 81 04 / 8 97 90
[email protected]
www.schweiger-gmbh.com
(1 to 5 pieces)
North
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 40
D-22339 Hamburg
Phone +49 (0) 40 / 53 80 92 20
Fax +49 (0) 40 / 53 80 92 84
[email protected]
South
HDS Ventilatoren Vertriebs GmbH
Glaswiesenstraße 1
D-74677 Dörzbach
Phone +49 (0) 79 37 / 80 29 68
Fax +49 (0) 79 37 / 80 25 78
[email protected]
D3G_englisch:Axial_D
30.04.2008
10:59
Seite 47
Europe
Austria
ebm-papst Motoren & Ventilatoren GmbH
Westbahnstraße 5
A-4490 St. Florian
Phone +43 / 72 24 / 66 01 10
Fax +43 / 72 24 / 66 01 120
[email protected]
www.ebmpapst.at
Belarus
ebm-papst Bel AgmbH
Prospekt Nesavisimosti 11/2 Zimmer 325, 512
BY-220050 Minsk
Phone +375 / 17 / 209 95 61
Fax +375 / 17 / 209 95 61
[email protected]
Belgium
VIBO Benelux B. V.
Sales office Belgium-Luxemburg
Romeinsestraat 6/0101
Research Park Haasrode
B-3001 Heverlee-Leuven
Phone +32 / 16 / 39 62 00
Fax +32 / 16 / 39 62 20
[email protected]
www.vibobenelux.com
Bulgaria
ebm-papst Romania S.R.L.
Str. Tirnavei Nr. 20
RO-500327 Brasov
Phone +40 / 268 / 312 805
Fax +40 / 268 / 312 805
[email protected]
Croatia
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 / 1 / 87 22 190
Fax +36 / 1 / 87 22 194
[email protected]
www.ebmpapst.hu
Cyprus
MATERO LTD
37, St. Kyriakides Avenue
P.O. Box 51744
CY-3080 Limassol
Phone +357 / 25 / 87 00 30
Fax +357 / 25 / 38 13 66
[email protected]
www.matero.com.cy
Greece
Helcoma
Th. Rotas & Co OE
Davaki 65
GR-17672 Kallithea-Attiki
Phone +30 / 210 / 951 37 05
Fax +30 / 210 / 951 34 90
[email protected]
www.helcoma.gr
Czech Republic / Slovakia
ebm-papst CZ s.r.o.
Krátká 379
CZ-66461 Rajhradice u Brna
Phone +420 / 5 / 47 23 26 16
Fax +420 / 5 / 47 23 26 22
[email protected]
www.ebmpapst.cz
Hungary
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 / 1 / 87 22 190
Fax +36 / 1 / 87 22 194
[email protected]
www.ebmpapst.hu
Denmark
Jenk A/S
Vallensbækvej 21
DK-2605 Brøndby
Phone +45 / 43 / 63 11 11
Fax +45 / 43 / 63 05 05
[email protected]
www.jenk.dk
Iceland
RJ Engineers
Stangarhyl 1A
IS-110 Reykjavik
Phone +354 / 567 80 30
Fax +354 / 567 80 15
[email protected]
www.rj.is
Estonia
ebm-papst Oy Eesti Filiaal
Kadaka tee 3
EST-10621 Tallinn
Phone +372 / 65 56 / 978
Fax +372 / 65 56 / 979
www.ebmpapst.ee
Ireland
ebm-papst Limited
Portlaoise Business & Technology Park
Mountrath Road
IRL-Portlaoise, Co. Laois
Phone +353 / 57 86 / 643 43
Fax +353 / 57 86 / 643 46
[email protected]
www.ebmpapst.ie
Finland
ebm-papst Oy
Puistotie 1
FIN-02760 Espoo
Phone +358 / 9 / 88 70 22 0
Fax +358 / 9 / 88 70 22 13
[email protected]
www.ebmpapst.fi
France
ebm-papst SARL
ZI Nord - rue A. Mohler
BP 62
F-67212 Obernai-Cedex
Phone +33 / 820 326 266
Fax +33 / 3 / 88 67 38 83
[email protected]
www.ebmpapst.fr
Italy
ebm-papst Srl
Via Cornaggia 108
I-22076 Mozzate (Co)
Phone +39 / 03 31 / 83 62 01
Fax +39 / 03 31 / 82 15 10
[email protected]
www.ebmpapst.it
Macedonia
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 / 1 / 87 22 190
Fax +36 / 1 / 87 22 194
[email protected]
www.ebmpapst.hu
47
D3G_englisch:Axial_D
30.04.2008
10:59
fan agent
compact fan agent
Seite 48
Distributors, agencies and subsidiaries
motor specialist
motor agent
Netherlands
VIBO Benelux B. V.
Engelseweg 127
Postbus 230
NL-5705 AC Helmond
Phone +31 / 4 92 / 50 29 00
Fax +31 / 4 92 / 50 29 50
[email protected]
www.vibobenelux.com
Norway
ebm-papst AS
P.B. 173 Holmlia
N-1203 Oslo
Phone +47 / 22 / 76 33 40
Fax +47 / 22 / 61 91 73
[email protected]
www.ebmpapst.no
Poland
ebm-papst Polska Sp. z o.o.
ul. Annopol 4A
PL-03236 Warszawa
Phone +48 / 22 / 675 78 19
Fax +48 / 22 / 676 95 87
[email protected]
www.ebmpapst.pl
Portugal
ebm-papst (Portugal), Lda.
Av. Marechal Gomes da Costa, 35 e
Rua Conselheiro Emidio Navarro
P-1800-255 Lisboa
Phone +351 / 21 / 839 48 80
Fax +351 / 21 / 839 47 59
[email protected]
Romania
ebm-papst Romania S.R.L.
Str. Tirnavei Nr. 20
RO-500327 Brasov
Phone +40 / 268 / 312 805
Fax +40 / 268 / 312 805
[email protected]
48
Russia
ebm-papst Ural GmbH
Rosa Luxemburg Strasse 59
RU-620026 Jekaterinburg
Phone +7 / 343 / 378 31 75
Fax +7 / 343 / 378 31 89
[email protected]
www.ebmpapst.ur.ru
Switzerland
ebm-papst AG
Rütisbergstraße 1
CH-8156 Oberhasli
Phone +41 / 44 / 732 20 70
Fax +41 / 44 / 732 20 77
[email protected]
www.ebmpapst.ch
ebm-papst Rus GmbH
Nizhegorodskaya 32, str. 15 office 420
RU-109029 Moskau
Phone +7 / 495 / 671 53 93
Fax +7 / 495 / 671 53 95
[email protected]
www.ebmpapst.ru
Turkey
Akantel Elektronik San. Tic. LTD. Sti.
Atatürk Organize Sanayi
Bölgesi 10007 SK. No.:6
TR-35620 Cigli-Izmir
Phone +90 / 2 32 / 32 82 090 -91
Fax +90 / 2 32 / 32 80 270
[email protected]
www.akantel.com.tr
ebm-papst Rus
Saint-Petersburg´s Filial
Zastavskaya 7
RU-196084 Sankt-Petersburg
Phone +7 / 812 / 449 96 07
Fax +7 / 812 / 449 96 07
[email protected]
Serbia & Montenegro
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 / 1 / 87 22 190
Fax +36 / 1 / 87 22 194
[email protected]
www.ebmpapst.hu
Spain
ebm-papst Ibérica S.L.
Avda. del Sistema Solar, 29
E-28830 San Fernando de Henares (Madrid)
Phone +34 / 91 / 678 08 94
Fax +34 / 91 / 678 15 30
[email protected]
Sweden
ebm-papst AB
Äggelundavägen 2
S-17562 Järfälla
Phone +46 / 8 / 761 94 00
Fax +46 / 8 / 36 23 06
[email protected]
www.ebmpapst.se
Ukraine
ebm-papst Ukraine LLC
Lepse Boulevard, 4, Building 47
UA-03067 Kiev
Phone +38 / 044 / 206 30 91
Fax +38 / 044 / 206 30 91
[email protected]
www.ebmpapst.ua
United Kingdom
ebm-papst UK Ltd.
Chelmsford Business Park
GB-Chelmsford Essex CM2 5EZ
Phone +44 / 12 45 / 46 85 55
Fax +44 / 12 45 / 46 63 36
[email protected]
www.ebmpapst.co.uk
ebm-papst Automotive & Drives (UK) Ltd.
The Smithy
Fidlers Lane, East Ilsley
GB-Berkshire RG20 7LG
Phone +44 / 87 07 / 66 51 70
Fax +44 / 87 07 / 66 51 80
A&[email protected]
www.ebmpapst-ad.com
D3G_englisch:Axial_D
30.04.2008
10:59
America
Argentina
ebm-papst de Argentina S.A.
Hernandarias 148 Lomas del Mirador
Pcia. de Buenos Aires (1752)
Phone +54 / 11 46 57 61 35
Fax +54 / 11 46 57 20 92
[email protected]
Brasil
ebm-papst Motores Ventiladores Ltda.
Av. José Giorgi, 301 Galpões B6+B7
Condominio Logical Center
BR-06707-100 Cotia - São Paulo
Phone +55 /11 / 31 64 89 00
Fax +55 /11 / 47 77 14 56
[email protected]
www.ebmpapst.com.br
Seite 49
USA
ebm-papst Inc.
P.O. Box 4009
100 Hyde Road
USA-Farmington, CT 06034
Phone +1 / 860 / 674 15 15
Fax +1 / 860 / 674 85 36
[email protected]
www.ebmpapst.us
ebm-papst Automotive & Drives, Inc.
3200 Greenfield, Suite 255
USA-Dearborn, MI 48120
Phone +1 / 313 / 406 80 80
Fax +1 / 313 / 406 80 81
[email protected]
www.ebmpapst-automotive.us
Africa
South Africa
ebm-papst South Africa (Pty) Ltd.
P.O. Box 3124
1119 Yacht Avenue
ZA-2040 Honeydew
Phone +27 / 11 / 794 34 34
Fax +27 / 11 / 794 50 20
[email protected]
www.ebmpapst.co.za
Canada
ebm-papst Canada Inc.
1800 Ironstone Manor, Unit 2
CDN-Pickering, Ontario, L1W3J9
Phone +1 / 905 / 420 / 35 33
Fax +1 / 905 / 420 / 37 72
[email protected]
www.ebmpapst.ca
Mexico
ebm Industrial S.de R.L. de C.V.
Paseo de Tamarindos 400-A-5to Piso
Col. Bosques de las Lomas
MEX-Mexico 05120, D.F.
Phone +52 / 55 / 50 91 44 44
Fax +52 / 55 / 50 91 44 43
[email protected]
www.ebmpapst.com.mx
49
D3G_englisch:Axial_D
30.04.2008
10:59
fan agent
compact fan agent
Seite 50
Distributors, agencies and subsidiaries
motor specialist
motor agent
Asia
China
ebm-papst Ventilator (Shanghai) Co., Ltd.
No. 418, Huajing Road
WaiGaoQiao Free Trade Zone
No. 2001, Yang Gao (N) Road
VRC-200131 Shanghai, P.R. of China
Phone +86 / 21 / 50 46 01 83
Fax +86 / 21 / 50 46 11 19
[email protected]
Hong Kong
ebm-papst Ventilator (Shanghai) Co., Ltd.
Hong Kong Representative Office
Unit Nos. 13, 9/F, Technology Park
18 On Lai Street, Sha Tin, N.T.
HK-Hong Kong P.R. of China
Phone +852 / 21 45 / 86 78
Fax +852 / 21 45 / 76 78
[email protected]
India
ebm NADI International Pvt Ltd.
26/3, G.N.T. Road, Erukkencherry
IND-Chennai-600118
Phone +91 / 44 / 25 37 25 56
Fax +91 / 44 / 25 37 11 49
[email protected]
www.ebmnadi.com
Indonesia
ebm-papst Indonesia
Wisma Slipi, Jl. Letjend S. Parman Kav. 12
14th Floor, No. 1410
RI-Jakarta Barat 11480
Phone +62 / 21 / 536 619 01
Fax +62 / 21 / 536 619 05
[email protected]
Israel
Polak Bros. Import Agencies Ltd.
9 Hamefalsim Street
IL-Kiryat Arie, Petach-Tikva 49514
Phone +972 / 3 / 910 03 00
Fax +972 / 3 / 579 66 79
[email protected]
www.polak.co.il
50
Japan
ebm-papst Industries Japan K.K.
12 Floor, Benex S-3 Bldg.
3-20-8 Shinyokohama, Kohoku-ku
J-222-0033 Yokohama
Phone +81 / 45 / 470 / 57 51
Fax +81 / 45 / 470 / 57 52
[email protected]
www.ebmpapst.jp
Korea
ebm-papst Korea Co. Ltd.
6F, Trutec Bldg.
B 6-2, Digital Media City (DMC)
Sangam-Dong, Mapo-Gu
ROK-Seoul 121-270
Phone +82 / 2 / 36 62 / 13 24
Fax +82 / 2 / 36 62 / 13 26
[email protected]
www.ebmpapst.co.kr
Malaysia
ebm-papst Malaysia
Representative Office
Block F1, 9A-4, Jalan PJU 1/42
Dataran Prima
MAL-47301 Petaling Jaya
Phone +60 / 3 / 78 06 54 40
Fax +60 / 3 / 78 06 54 41
[email protected]
Singapore
ebm-papst SEA Pte. Ltd.
23 Ubi Road 4, #05-00
Olympia Industrial Building
SGP-Singapore 408620
Phone +65 / 68 42 84 38
Fax +65 / 68 42 84 39
[email protected]
Taiwan
ETECO Engineering & Trading Corp.
10F-I, No. 92, Teh-Wei Str.
RC-Tsow-Inn District, Kaohsiung
Phone +886 / 7 / 557 42 68
Fax +886 / 7 / 557 27 88
[email protected]
Thailand
ebm-papst Thailand Co. Ltd.
Representative Office
99/349 Chaeng Wattana Road, Laksi
Bangkok 10210, Thailand
Phone +66 / 2 / 576 / 15 24-5
Fax +66 / 2 / 576 / 15 42
[email protected]
United Arab Emirates
ebm-papst Middle East FZE
PO Box 17755
Jebel Ali Free Zone / FZS1 / AP05
UAE-Dubai
Phone +971 / 4 / 886 08 26
Fax +971 / 4 / 886 08 27
[email protected]
D3G_englisch:Axial_D
30.04.2008
10:59
Seite 51
Australia
Australia
ebm-papst Australia Pty Ltd.
2 Silverton Close
AUS-Laverton North, Victoria, 3026
Phone +61 / 3 / 83 25 64 00
Fax +61 / 3 / 83 25 64 64
[email protected]
www.ebm-papst.com.au
New Zealand
ebm-papst Australia Pty Ltd.
102 Henderson Valley Road
NZ-Henderson, Auckland 1230
Phone +64 / 9 / 837 18 84
Fax +64 / 9 / 837 18 99
[email protected]
www.ebm-papst.com.au
51
D3G_englisch:Axial_D
30.04.2008
10:59
Seite 52
37799-7-8811 · RA-04/08-3’
ebm-papst
Mulfingen GmbH & Co. KG
Bachmühle 2
D-74673 Mulfingen
Phone +49 (0) 79 38 / 81-0
Fax +49 (0) 79 38 / 81-110
[email protected]
www.ebmpapst.com