32-Bit Microcontroller TC1728 32-Bit Single-Chip Microcontroller Data Sheet V1.2 2014-06 Microcontrollers Edition 2014-06 Published by Infineon Technologies AG 81726 Munich, Germany © 2014 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. 32-Bit Microcontroller TC1728 32-Bit Single-Chip Microcontroller Data Sheet V1.2 2014-06 Microcontrollers TC1728 Table of Contents Table of Contents 1 Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 2 2.1 System Overview of the TC1728 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 4 Identification Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 5 5.1 5.1.1 5.1.2 5.1.3 5.1.4 5.1.5 5.2 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.5.1 5.3 5.3.1 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 5.3.7 5.3.8 5.3.9 5.3.10 5.3.11 5.3.11.1 5.3.11.2 5.3.11.3 5.3.11.4 5.4 5.4.1 5.4.2 Electrical Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 General Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Parameter Interpretation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Pad Driver and Pad Classes Summary . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Pin Reliability in Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 DC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Input/Output Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Analog to Digital Converters (ADCx) . . . . . . . . . . . . . . . . . . . . . . . . . 5-23 Fast Analog to Digital Converter (FADC) . . . . . . . . . . . . . . . . . . . . . . 5-33 Oscillator Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-38 Power Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-39 Calculating the 1.3 V Current Consumption . . . . . . . . . . . . . . . . . 5-42 AC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-43 Testing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-43 Power Sequencing 5V Supply Only . . . . . . . . . . . . . . . . . . . . . . . . . . 5-44 Power Sequencing 3.3V Supply Only . . . . . . . . . . . . . . . . . . . . . . . . 5-46 Power Sequencing all Voltages supplied from External . . . . . . . . . . 5-48 Power, Pad and Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-50 EVR Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-53 Phase Locked Loop (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-55 ERAY Phase Locked Loop (ERAY_PLL) . . . . . . . . . . . . . . . . . . . . . . 5-57 JTAG Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-58 DAP Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-60 Peripheral Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-62 Micro Link Interface (MLI) Timing . . . . . . . . . . . . . . . . . . . . . . . . . 5-62 Micro Second Channel (MSC) Interface Timing . . . . . . . . . . . . . . 5-64 SSC Master/Slave Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 5-67 ERAY Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-70 Package and Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-71 Package Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-71 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-72 Data Sheet I-1 V1.2, 2014-06 TC1728 Table of Contents 5.4.3 5.4.4 6 Data Sheet Flash Memory Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-72 Quality Declarations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 I-2 V1.2, 2014-06 TC1728 Summary of Features 1 Summary of Features The SAK-TC1728N-192F133HL / SAK-TC1728N-192F133HR has the following features: • • • • • • • High-performance 32-bit super-scalar TriCore V1.3.1 CPU with 4-stage pipeline – Superior real-time performance – Strong bit handling – Fully integrated DSP capabilities – Single precision Floating Point Unit (FPU) – 133 MHz operation at full temperature range 32-bit Peripheral Control Processor with single cycle instruction (PCP2) – 8 Kbyte Parameter Memory (PRAM) – 24 Kbyte Code Memory (CMEM) – 133 MHz operation at full temperature range Multiple on-chip memories – 1.5 Mbyte Program Flash Memory (PFLASH) with ECC – 64 Kbyte Data Flash Memory (DFLASH) usable for EEPROM emulation – 120 Kbyte Data Memory (LDRAM) – Instruction Cache: up to 8Kbyte (ICACHE, configurable) – 24 Kbyte Code Scratchpad Memory (SPRAM) – Data Cache: up to 4 Kbyte (DCACHE, configurable) – 8 Kbyte Overlay Memory (OVRAM) – 16 Kbyte BootROM (BROM) 16-Channel DMA Controller Sophisticated interrupt system with 2 × 255 hardware priority arbitration levels serviced by CPU or PCP2 High performing on-chip bus structure – 64-bit Local Memory Buses between CPU, Flash and Data Memory – 32-bit System Peripheral Bus (SPB) for on-chip peripheral and functional units – One bus bridge (LFI Bridge) Versatile On-chip Peripheral Units – Two Asynchronous/Synchronous Serial Channels (ASC) with baud rate generator, parity, framing and overrun error detection – Four High-Speed Synchronous Serial Channels (SSC) with programmable data length and shift direction – One serial Micro Second Bus interface (MSC) for serial port expansion to external power devices – One High-Speed Micro Link interface (MLI) for serial inter-processor communication – One MultiCAN Module with 3 CAN nodes and 64 free assignable message objects for high efficiency data handling via FIFO buffering and gateway data transfer Data Sheet 1-1 V1.2, 2014-06 TC1728 Summary of Features • • • • • • • • – One General Purpose Timer Array Module (GPTA) providing a powerful set of digital signal filtering and timer functionality to realize autonomous and complex Input/Output management – Two Capture/Compare Unit 6 (CAPCOM6) kernels – Two General Purpose Timer (GPT12) modules 36 analog input lines for ADC – 2 independent kernels (ADC0 and ADC1) – Analog supply voltage range from 3.3 V to 5 V (single supply) – Broken wire detection 2 different FADC input channels – channels with impedance control and overlaid with ADC1 inputs – Extreme fast conversion, 21 cycles of fFADC clock – 10-bit A/D conversion (higher resolution can be achieved by averaging of consecutive conversions in digital data reduction filter) 127 digital general purpose I/O lines (GPIO), 3 input lines Digital I/O ports with 3.3 V capability On-chip debug support for OCDS Level 1 (CPU, PCP, DMA, On Chip Bus) Dedicated Emulation Device chip available (TC1728ED) – multi-core debugging, real time tracing, and calibration – four/five wire JTAG (IEEE 1149.1) or two wire DAP (Device Access Port) interface Power Management System Clock Generation Unit with PLL The SAK-TC1728F-192F133HL / SAK-TC1728F-192F133HR features: • • • has the following High-performance 32-bit super-scalar TriCore V1.3.1 CPU with 4-stage pipeline – Superior real-time performance – Strong bit handling – Fully integrated DSP capabilities – Single precision Floating Point Unit (FPU) – 133 MHz operation at full temperature range 32-bit Peripheral Control Processor with single cycle instruction (PCP2) – 8 Kbyte Parameter Memory (PRAM) – 24 Kbyte Code Memory (CMEM) – 133 MHz operation at full temperature range Multiple on-chip memories – 1.5 Mbyte Program Flash Memory (PFLASH) with ECC – 64 Kbyte Data Flash Memory (DFLASH) usable for EEPROM emulation – 120 Kbyte Data Memory (LDRAM) – Instruction Cache: up to 8Kbyte (ICACHE, configurable) – 24 Kbyte Code Scratchpad Memory (SPRAM) – Data Cache: up to 4 Kbyte (DCACHE, configurable) – 8 Kbyte Overlay Memory (OVRAM) Data Sheet 1-2 V1.2, 2014-06 TC1728 Summary of Features • • • • • • • • • • • • – 16 Kbyte BootROM (BROM) 16-Channel DMA Controller Sophisticated interrupt system with 2 × 255 hardware priority arbitration levels serviced by CPU or PCP2 High performing on-chip bus structure – 64-bit Local Memory Buses between CPU, Flash and Data Memory – 32-bit System Peripheral Bus (SPB) for on-chip peripheral and functional units – One bus bridge (LFI Bridge) Versatile On-chip Peripheral Units – Two Asynchronous/Synchronous Serial Channels (ASC) with baud rate generator, parity, framing and overrun error detection – Four High-Speed Synchronous Serial Channels (SSC) with programmable data length and shift direction – One serial Micro Second Bus interface (MSC) for serial port expansion to external power devices – One High-Speed Micro Link interface (MLI) for serial inter-processor communication – One MultiCAN Module with 3 CAN nodes and 64 free assignable message objects for high efficiency data handling via FIFO buffering and gateway data transfer – One FlexRayTM module with 2 channels (E-Ray). – One General Purpose Timer Array Module (GPTA) providing a powerful set of digital signal filtering and timer functionality to realize autonomous and complex Input/Output management – Two Capture/Compare Unit 6 (CAPCOM6) kernels – Two General Purpose Timer (GPT12) modules 36 analog input lines for ADC – 2 independent kernels (ADC0 and ADC1) – Analog supply voltage range from 3.3 V to 5 V (single supply) – Broken wire detection 2 different FADC input channels – channels with impedance control and overlaid with ADC1 inputs – Extreme fast conversion, 21 cycles of fFADC clock – 10-bit A/D conversion (higher resolution can be achieved by averaging of consecutive conversions in digital data reduction filter) 127 digital general purpose I/O lines (GPIO), 3 input lines Digital I/O ports with 3.3 V capability On-chip debug support for OCDS Level 1 (CPU, PCP, DMA, On Chip Bus) Dedicated Emulation Device chip available (TC1728ED) – multi-core debugging, real time tracing, and calibration – four/five wire JTAG (IEEE 1149.1) or two wire DAP (Device Access Port) interface Power Management System Clock Generation Unit with PLL Data Sheet 1-3 V1.2, 2014-06 TC1728 Summary of Features Ordering Information The ordering code for Infineon microcontrollers provides an exact reference to the required product. This ordering code identifies: • • The derivative itself, i.e. its function set, the temperature range, and the supply voltage The package and the type of delivery. For the available ordering codes for the TC1728 please refer to the “Product Catalog Microcontrollers”, which summarizes all available microcontroller variants. This document describes the derivatives of the device.The Table 1 enumerates these derivatives and summarizes the differences. Table 1 TC1728 Derivative Synopsis Derivative SAK-TC1728N-192F133HL SAK-TC1728N-192F133HR SAK-TC1728F-192F133HR SAK-TC1728F-192F133HL 1) 2) Ambient Temperature Range ERAY Wire Bond Material TA = -40oC to +125oC No Gold TA = -40oC to +125oC No Copper o o Yes Copper o o Yes Gold TA = -40 C to +125 C TA = -40 C to +125 C 1) This derivative has the same features as the SAK-TC1728N-192F133HL, except the wire-bonding material. 2) This derivative has the same features as the SAK-TC1728F-192F133HL, except the wire-bonding material. Data Sheet 1-4 V1.2, 2014-06 TC1728 System Overview of the TC1728 2 System Overview of the TC1728 The TC1728 combines three powerful technologies within one silicon die, achieving new levels of power, speed, and economy for embedded applications: • • • Reduced Instruction Set Computing (RISC) processor architecture Digital Signal Processing (DSP) operations and addressing modes On-chip memories and peripherals DSP operations and addressing modes provide the computational power necessary to efficiently analyze complex real-world signals. The RISC load/store architecture provides high computational bandwidth with low system cost. On-chip memory and peripherals are designed to support even the most demanding high-bandwidth real-time embedded control-systems tasks. Additional high-level features of the TC1728 include: • • • • • • • • • Efficient memory organization: instruction and data scratch memories, caches Serial communication interfaces – flexible synchronous and asynchronous modes Peripheral Control Processor – standalone data operations and interrupt servicing DMA Controller – DMA operations and interrupt servicing General-purpose timers High-performance on-chip buses On-chip debugging and emulation facilities Flexible interconnections to external components Flexible power-management The TC1728 is a high-performance microcontroller with TriCore CPU, program and data memories, buses, bus arbitration, an interrupt controller, a peripheral control processor and a DMA controller and several on-chip peripherals. The TC1728 is designed to meet the needs of the most demanding embedded control systems applications where the competing issues of price/performance, real-time responsiveness, computational power, data bandwidth, and power consumption are key design elements. The TC1728 offers several versatile on-chip peripheral units such as serial controllers, timer units, CAPCOM6 and Analog-to-Digital converters. Within the TC1728, all these peripheral units are connected to the TriCore CPU/system via the Flexible Peripheral Interconnect (FPI) Bus and the Local Memory Bus (LMB). Several I/O lines on the TC1728 ports are reserved for these peripheral units to communicate with the external world. Data Sheet 2-1 V1.2, 2014-06 TC1728 System Overview of the TC1728 2.1 Block Diagrams Figure 1 shows the block diagram of the SAK-TC1728N-192F133HL./ SAK-TC1728N192F133HR. Abbreviations: ICACHE: Instruction Cache DCACHE Data Cache SPRAM: Scratch-Pad RAM LDRAM: Local Data RAM OVRAM: Overlay RAM BROM: Boot ROM PFlash: Program Flash DFlash: Data Flash PRAM: Parameter RAM in PCP CMEM: Code RAM in PCP FPU PMI DMI TriCore CPU 16 KB SPRAM 8 KB ICACHE (Configurable) 116 KB LDRAM 4 KB DCACHE (Configurable) TC1.3.1 133MHz CPS Local Memory Bus LBCU (LMB) 1.3V, 3.3V Int. Supply DMA LFI Bridge 16 channels SMIF M PMU 1,5 MB PFlash 64 KB Dflash 16 KB BROM 8 KB OVRAM Optional Ext. Supply EVR 5V, 3.3V Single-source Ext. Supply Embedded Voltage Regulator M/S OCDS L1 Debug Interface ASC0 ASC1 JTAG/DAP Interrupt System MLI0 Interrupts FPI-Bus Interface 8 KB PRAM System Peripheral Bus (SPB) PCP2 Core STM MemCheck 24 KB CMEM CAPCOM (CCU60, CCU61) GPT12 (GPT 120) System Peripheral Bus SCU FCE Ports 5V Ext. ADC Supply BMU ADC0 GPT12 (GPT 121) SSC0 SBCU PLL fCPU 16 (5V max, 24 channels ) 4 FADC SSC2 Ext. Request Unit MultiCAN (3 Nodes, 64 MO) MSC0 SSC3 LVDS Data Sheet 16 ADC1 SSC1 GPTA 0 Figure 1 (5V max, 16 channels ) (3.3V max, 2 differential channels ) BlockDiagram TC1728N V0.8 SAK-TC1728N-192F133HL / SAK-TC1728N-192F133HR Block Diagram 2-2 V1.2, 2014-06 TC1728 System Overview of the TC1728 Figure 2 shows the block diagram of the SAK-TC1728F-192F133HL / SAK-TC1728F192F133HR. Abbreviations: ICACHE: Instruction Cache DCACHE Data Cache SPRAM: Scratch-Pad RAM LDRAM: Local Data RAM OVRAM: Overlay RAM BROM: Boot ROM PFlash: Program Flash DFlash: Data Flash PRAM: Parameter RAM in PCP CMEM: Code RAM in PCP FPU PMI DMI TriCore CPU 16 KB SPRAM 8 KB ICACHE (Configurable) 116 KB LDRAM 4 KB DCACHE (Configurable) TC1.3.1 133MHz CPS Local Memory Bus LBCU (LMB) 1.3V, 3.3V Int. Supply DMA LFI Bridge 16 channels SMIF M PMU 1,5 MB PFlash 64 KB Dflash 16 KB BROM 8 KB OVRAM Optional Ext. Supply EVR 5V, 3.3V Single-source Ext. Supply Embedded Voltage Regulator M/S OCDS L1 Debug Interface ASC0 ASC1 System Peripheral Bus (SPB) JTAG/DAP Interrupt System MLI0 Interrupts FPI-Bus Interface 8 KB PRAM PCP2 Core STM MemCheck 24 KB CMEM SCU CAPCOM (CCU60, CCU61) GPT12 (GPT 120) System Peripheral Bus E-Ray (2 channels) FCE Ports 5V Ext. ADC Supply BMU ADC0 GPT12 (GPT 121) SBCU PLL E-RAY PLL f E-Ray SSC0 fCPU (5V max, 16 channels ) 16 ADC1 16 (5V max, 24 channels ) 4 SSC1 GPTA 0 FADC SSC2 Ext. Request Unit MultiCAN (3 Nodes, 64 MO) MSC0 SSC3 (3.3V max, 2 differential channels ) BlockDiagram TC1728F LVDS Figure 2 Data Sheet SAK-TC1728F-192F133HR Block Diagram 2-3 V1.2, 2014-06 TC1728 Pinning 3 Pinning Figure 3-1 shows the TC1728 Logic Symbol. Alternate Functions General Control 16 PORST TESTMODE ESR0 ESR1 16 14 16 TRST OCDS / JTAG Control Analog Inputs Analog Power Supply TCK / DAP0 4 TMS / DAP1 16 AN[35:0] VD D M VSSM V AR EF0 VAGN D 0 V5 Digital Circuitry Power Supply VD D VD D P V SS EVR Pass Device Gate V PD G TC1728 4 14 7 4 4 5 16 4 2 1 Port 0 Port 1 Port 2 Port 3 GPTA, SCU, ERAY 1 ), MSC0, CCU6, GPT12, MultiCAN SCU, GPTA, SSC1, ADC0, OCDS, CCU6, GPT12 GPTA, SSC0/1, MLI0, MSC0, CCU6, GPT12 GPTA, ASC0/1, SSC0/1, SCU, CAN, MSC0 Port 4 GPTA, SCU, CAN, CCU6, GPT12 Port 5 GPTA, ERAY 1 ), SSC0/2, CAN, CCU6, GPT12, SCU, ADC1 Port 6 GPTA, MSC0 Port 8 CCU6, GPT12, SSC3, GPTA Port 9 GPTA, CCU6, OCDS/JTAG Port 10 SSC2 Port 11 Overlaid digital /analog inputs XTAL1 XTAL2 Oscillator 1) On ly a va ila b le fo r SAK- TC1 7 2 8F-1 9 2F1 3 3H R TC1728_LogSym_176 Figure 3-1 Data Sheet TC1728 Logic Symbol 3-1 V1.2, 2014-06 TC1728 REQ7/CC 62/ CC62INA /B/CAPINA/B/SLSO20 /OUT 40 /IN40 /P5 .0 SLSO21 /OUT 41 /IN41 /P5 .1 COUT 62 /SLSO22 /OUT 42 /IN42 /P5 .2 SLSO23 /OUT 43 /IN43 /P5 .3 SLSI2 A/SLSO24 /OUT 44 /IN44 /P5 .4 M RST2A/OUT 45 /IN45 /P5 .5 M T SR2A/OUT 46 /IN46 /P5 .6 SCLK2A/OUT 47 /IN47 /P5 .7 1) T XDCAN0/OUT 37 /RXDB1 /P5. 15 VDD CC60 IN C/CC 60/ OU T87/P 9.7 COU T60/ OU T88/P 9.8 CC61 /CC61 INA/B/T XDA11 )/OUT 6/P5 .8 1) OUT 7/RXDCAN0 /T XDB1 /P5 .9 1) COUT 61/ OUT 8/T XENA1 )/P5.10 COUT 63/ OUT 9/T XENB /P5.11 CCPOS0 A/ T12 HRB/T 3INA/B/ AD1 EM UX0 /SLSO07 /OUT 19 /P5.12 1) TC1728 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 P3 .4/OUT 88 /M T SR0 P3 .7/SLSI 0/OUT 89 /SLSO02 /SLSO 12 P3 .3/OUT 87 /M RST0 P3 .2/OUT 86 /SCLK0 P3 .8/SLSO 06/ OUT 90/ T XD1/ REQ14 P3 .6/SLSO 01/ SLSO11 /SLSO01 &SLSO11 P3 .5/SLSO 00/ SLSO10 /SLSO00 &SLSO10 P 8.13/ OU T4 /COU T60 P 8.3/ SLSI3 /CC 61IN C/ CC61/ OU T51/ SLSO30 P 8.4/ OU T99 /COU T62/ SLSO31 ESR0 PORST ESR1 P1. 1/IN17 /OUT 17 /OUT 73 /T 13 HRE/CT RAPB T EST M ODE P1.15 /BRKIN/ BRKOUT P1.0 /REQ15 /IN16 /OUT 16 /OUT 72 /T 3OUT /BRKIN /BRKOUT T CK/DAP0 T RST P9 .6/T DO/ BRKIN/BRKOUT T M S/ DAP1 P9 .5/T DI/BRKIN/ BRKOUT P1 .7/IN 23/ OUT 23/OUT 79 P1 .6/IN 22/ OUT 22/OUT 78 P1 .5/IN 21/ OUT 21/OUT 77 V5 V DDP V DD V SS XT AL2 XT AL1 V SS P 8.12/ OU T107 P1 .4/IN 20/ EM GST OP/OUT 20 /OUT 76 /COUT 61 P1 .3/IN 19/ OUT 19/ OUT 75/COUT 63 P1 .11 /IN27 /IN51 /SCLK1 B/ OUT 27/ OUT 51/ CCPOS0C/T 2INA/ B P1 .10 /IN26 /IN50 /OUT 26 /OUT 50 /SLSO17 P1 .9/IN 25/ IN49 /M RST1B/OUT 25 /OUT 49 /CCPOS1 C/T 2EUDA/B P1 .8/IN 24/ IN48 /M T SR1B/OUT 24 /OUT 48 /CCPOS2 C/T 4EUDA/B P1 .2/IN 18/ OUT 18/OUT 74 P8.11 /OUT 106 P8.10 /OUT 105 P4 .3/IN 31/ IN55 /OUT 31/ OUT 55/ EXT CLK0 /T12 HRE/CT RAPA P8.9 /OUT 57 /SLSO34 AN1 9/DIG 3/P1 1.3 AN1 8/DIG 2/P1 1.2 AN1 7/DIG 1/P1 1.1 AN1 6/DIG 0/P1 1.0 AN15 AN14 VAGND0 V AREF0 VSSM VDDM AN13 AN12 AN11 AN10 AN9 AN8 AN6 AN5 AN4 AN3 AN2 AN1 AN0 V DD V DDP V5 AD0EM UX2/P1 .14 AD0EM UX1/P1 .13 AD0EM UX0/P1 .12 CC62 /CC62 INA/B/T CLK0/ OUT 32/ IN32 /P2.0 CCPOS0A/T 12 HRB/T 2INA/B/SLSO 13/ SL SO03 /OUT 33 /TR EADY0A/ IN33 /P2.1 CC61 /CC6 1INA/B/T VALID0 A/ OUT 34/ IN34 /P2.2 T1 2HRC/ T1 3HRC/C CPO S2A/T 4EUDA/B/T DATA0/ OUT 35/ IN35 /P2.3 COUT 63 /OUT 36 /RCLK0A/ IN36 /P2.4 CC6 0/CC6 0INA/B/RR EADY0 A/ OUT 37/ IN37 /P2.5 COUT 62 /OUT 38 /RVAL ID0A/ IN38 /P2.6 COUT 60 /OUT 39/ RDATA0A/ IN39 /P2.7 SLSO 32 /O U T100/ CC6 0/C C60IN C/ P8.5 C OU T61/ O U T101/ P8.6 CC 62IN C/ CC62/ O U T102/ P8.7 SLSO33 /O U T56/ P8.8 RXDCAN2/O UT5 2/O UT2 8/I N52/ IN28 /P4.0 T XDCAN2/O UT5 3/O UT2 9/I N53/ IN29 /P4.1 T 13H RB/ CCPOS1A/T 2EUDA/B/EXT CLK1/O UT5 4/O UT3 0/I N54/ IN30 /P4.2 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 CCPOS2A/T 12HRC /T13 HRC/ T4 INA/B/OUT 36 /AD1EM UX2/RXDA1 /P5.14 V DDP V DD(SB) V5 M RST2B /P 10.0 M TSR2B /P 10.1 SCLK2B /P 10.2 SLSI 2B/SLSO20 /P 10.3 VPDG AN35 AN34 AN33 AN32 AN31 /DIG 15/ P11 .15 AN30 /DIG 14/ P11 .14 AN29 /DIG 13/ P11 .13 AN28 /DIG 12/ P11 .12 AN7 AN27 /DIG 11/ P11 .11 AN26 /DIG 10/ P11 .10 AN25 /DIG9 /P11 .9 AN24 /DIG8 /P11 .8 AN23 /DIG7 /P11 .7 AN22 /DIG6 /P11 .6 AN21 /DIG5 /P11 .5 AN20 /DIG4 /P11 .4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 17 6 17 5 17 4 17 3 17 2 17 1 17 0 16 9 16 8 167 16 6 16 5 16 4 16 3 16 2 16 1 16 0 15 9 15 8 1 57 15 6 15 5 15 4 15 3 15 2 15 1 15 0 14 9 14 8 147 14 6 14 5 14 4 14 3 14 2 14 1 14 0 13 9 13 8 137 13 6 13 5 13 4 13 3 P0.1 5/IN 15/ REQ 5/O UT1 5/O UT7 1/CO UT6 1 P0.1 4/IN 14/ REQ 4/O UT1 4/O UT7 0/CC 61IN C/ CC61 P0.7 /IN7 /HWCF G7/R EQ 3/O UT7 /OUT 63 /EVT O3 P0.6 /IN6 /HWCF G6/R EQ 2/O UT6 /OUT 62 /EVT O2 P9.2 /CO UT6 3/O U T82 P9.3 /O U T83/ CO U T62 P9.4 /CC 62IN C/ CC62 /O U T84 1) P0.1 3/IN 13/ OUT 13/T XE NB 1)/O UT6 9 P0.1 2/IN 12/ OUT 12/T XE NA /O UT6 8/CT RAPB/T1 3HRE P0.5 /IN5 /HWCF G5/O UT5 /OUT 61 /EVTO 1 P0.4 /IN4 /HWCF G4/O UT4 /OUT 60 /EVTO 0 P2.1 3/SL SI 11/SDI 0/CT RAPA/ T1 2HRE/SLSO 16/ T6O UT P2.8 /SLSO0 4/SLSO 14/ EN0 0 P2.1 2/M TSR1 A/SOP0B P2.1 1/SCL K1 A/FC LP0B P2.1 0/M RST1 A P2.9 /SLSO0 5/SLSO 15/ EN0 1 P6.3 /OUT 83 /SOP0A P6.2 /OUT 82 /SON0 P6.1 /OUT 81 /FC LP0A P6.0 /OUT 80 /FC LN0 V5 VDDP VDD P0.1 1/IN 11/ OUT 11/O UT6 7/REQ 9 P0.1 0/IN 10/ OUT 10/O UT6 6 P0.9 /IN9 /OUT 9/O UT6 5/T 6O UT P0.8 /IN8 /OUT 8/O UT6 4/T 3O UT P0.3 /IN3 /HWCF G3/O UT3 /OUT 59 P0.2 /IN2 /HWCF G2/O UT2 /OUT 58 P0.1 /IN1 /HWCF G1/O UT1 /OUT 57 /SDI1/ COUT 60 P0.0 /IN0 /HWCF G0/O UT0 /OUT 56 /CC60 /CC6 0INA/B P3.1 1/O UT9 3//R EQ 1 P3.1 2/O UT9 4//R XDC AN0 /RXD0B P3.1 3/O UT9 5//T XDCAN0/ TXD0 P8.0 /SCLK3 /CC PO S0C/ T3IN A/ B/ O UT4 8 P8.1 /M RST3/ CCP OS1 C/T 3EU DA /B /O U T49 P8.2 /M TSR3/ CCP OS2 C/T 4IN A/ B/ OU T50 P3.9 /OUT 91 /RXD1A P3.1 0/O UT9 2/REQ0 P3.0 /OUT 84 /RXD0A/RE Q 6 P3.1 /OUT 85 /TXD0 P3.1 4/O UT9 6RXDCAN1/ RXD1B/SDI2 P3.1 5/O UT9 7/T XDCAN1/T XD1 Pinning 1) Only available for SAK -T C1728 F- 192 F133 HR TC1728_QFP176 Figure 3-2 SAK-TC1728N-192F133HL / SAK-TC1728N-192F133HR / SAKTC1728F-192F133HR Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) Pin Symbol Ctrl. Type Function Port 0 Data Sheet 3-2 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 145 P0.0 I/O0 A1/ PU 146 147 148 Port 0 General Purpose I/O Line 0 IN0 I CCU60 I CC60INA CCU61 I CC60INB HWCFG0 I Hardware Configuration Input 0 OUT0 O1 GPTA0 Output 0 OUT56 O2 GPTA0 Output 56 GPTA0 Input 0 CCU60 O3 P0.1 I/O0 IN1 I SDI1 I MSC0 Serial Data Input 1 HWCFG1 I Hardware Configuration Input 1 OUT1 O1 GPTA0 Output 1 OUT57 O2 GPTA0 Output 57 CCU60 O3 COUT60 P0.2 I/O0 IN2 I CC60 A1/ PU A1/ PU Port 0 General Purpose I/O Line 1 GPTA0 Input 1 Port 0 General Purpose I/O Line 2 GPTA0 Input 2 HWCFG2 I Hardware Configuration Input 2 OUT2 O1 GPTA0 Output 2 OUT58 O2 GPTA0 Output 58 Reserved O3 P0.3 I/O0 IN3 I A1+/ Port 0 General Purpose I/O Line 3 PU GPTA0 Input 3 HWCFG3 I Hardware Configuration Input 3 OUT3 O1 GPTA0 Output 3 OUT59 O2 GPTA0 Output 59 Reserved O3 - Data Sheet 3-3 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 166 P0.4 I/O0 IN4 I A1/ PD HWCFG4 I Hardware Configuration Input 4 OUT4 O1 GPTA0 Output 4 OUT60 O2 GPTA0 Output 60 EVTO0 O3 MCDS event output 0 P0.5 I/O0 IN5 I HWCFG5 I Hardware Configuration Input 5 OUT5 O1 GPTA0 Output 5 OUT61 O2 GPTA0 Output 61 EVTO1 O3 MCDS event output 1 167 173 174 P0.6 I/O0 IN6 I HWCFG6 I A1/ PD A1/ PU Port 0 General Purpose I/O Line 4 GPTA0 Input 4 Port 0 General Purpose I/O Line 5 GPTA0 Input 5 Port 0 General Purpose I/O Line 6 GPTA0 Input 6 Hardware Configuration Input 6 REQ2 I External Request Input 2 OUT6 O1 GPTA0 Output 6 OUT62 O2 GPTA0 Output 62 EVTO2 O3 MCDS event output 2 P0.7 I/O0 IN7 I HWCFG7 I Hardware Configuration Input 7 REQ3 I External Request Input 3 OUT7 O1 GPTA0 Output 7 OUT63 O2 GPTA0 Output 63 EVTO3 O3 MCDS event output 3 Data Sheet A1/ PU Port 0 General Purpose I/O Line 7 GPTA0 Input 7 3-4 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 149 P0.8 I/O0 IN8 I A1/ PU OUT8 O1 GPTA0 Output 8 OUT64 O2 GPTA0 Output 64 150 151 152 168 Port 0 General Purpose I/O Line 8 GPTA0 Input 8 GPT121 O3 P0.9 I/O0 IN9 I GPTA0 Input 9 OUT9 O1 GPTA0 Output 9 OUT65 O2 GPTA0 Output 65 T3OUT A1/ PU Port 0 General Purpose I/O Line 9 GPT121 O3 P0.10 I/O0 IN10 I OUT10 O1 GPTA0 Output 10 OUT66 O2 GPTA0 Output 66 T6OUT A2/ PU Port 0 General Purpose I/O Line 10 GPTA0 Input 10 Reserved O3 P0.11 I/O0 IN11 I GPTA0 Input 11 REQ9 I External Request Input 9 OUT11 O1 GPTA0 Output 11 OUT67 O2 GPTA0 Output 67 Reserved O3 - A2/ PU P0.12 I/O0 IN12 I CCU60 I CTRAPB CCU61 I T13HRE OUT12 O1 GPTA0 Output 12 OUT68 O2 GPTA0 Output 68 TXENA O3 E-Ray Channel A transmit Data Output enable1) Data Sheet A2/ PU Port 0 General Purpose I/O Line 11 Port 0 General Purpose I/O Line 12 GPTA0 Input 12 3-5 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 169 P0.13 I/O0 IN13 I A2/ PU OUT13 O1 GPTA0 Output 13 OUT69 O2 GPTA0 Output 69 TXENB O3 E-Ray Channel B transmit Data Output enable1) P0.14 I/O0 IN14 I REQ4 I External Request Input 4 CCU61 I CC61INC OUT14 O1 GPTA0 Output 14 OUT70 O2 GPTA0 Output 70 CCU60 O3 P0.15 I/O0 IN15 I 175 176 Port 0 General Purpose I/O Line 13 GPTA0 Input 13 A1+/ Port 0 General Purpose I/O Line 14 PU GPTA0 Input 14 CC61 A1+/ Port 0 General Purpose I/O Line 15 PU GPTA0 Input 15 REQ5 I External Request Input 5 OUT15 O1 GPTA0 Output 15 OUT71 O2 GPTA0 Output 71 CCU60 O3 COUT61 Port 1 116 P1.0 I/O0 REQ15 I IN16 I GPTA0 Input 16 BRKIN I Break Input OUT16 O1 GPTA0 Output 16 OUT72 O2 GPTA0 Output 72 GPT120 O3 T3OUT BRKOUT O Break Output (controlled by OCDS module) Data Sheet A2/ PU Port 1 General Purpose I/O Line 0 External Request Input 15 3-6 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 119 P1.1 I/O0 IN17 I A1/ PU CCU60 I T13HRE CCU61 I CTRAPB OUT17 O1 GPTA0 Output 17 OUT73 O2 GPTA0 Output 73 Reserved O3 - 93 98 99 108 A1/ PU Port 1 General Purpose I/O Line 1 GPTA0 Input 17 P1.2 I/O0 IN18 I OUT18 O1 GPTA0 Output 18 OUT74 O2 GPTA0 Output 74 Reserved O3 A1/ PU Port 1 General Purpose I/O Line 2 GPTA0 Input 18 P1.3 I/O0 IN19 I OUT19 O1 GPTA0 Output 19 OUT75 O2 GPTA0 Output 75 CCU61 O3 COUT63 A1/ PU Port 1 General Purpose I/O Line 3 GPTA0 Input 19 P1.4 I/O0 IN20 I EMGSTOP I Emergency Stop Input OUT20 O1 GPTA0 Output 20 OUT76 O2 GPTA0 Output 76 CCU61 O3 COUT61 GPTA0 Input 20 P1.5 I/O0 IN21 I OUT21 O1 GPTA0 Output 21 OUT77 O2 GPTA0 Output 77 Reserved O3 - Data Sheet A1/ PU Port 1 General Purpose I/O Line 4 Port 1 General Purpose I/O Line 35 GPTA0 Input 21 3-7 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 109 P1.6 I/O0 IN22 I A1/ PU OUT22 O1 GPTA0 Output 22 OUT78 O2 GPTA0 Output 78 110 94 95 Port 1 General Purpose I/O Line 6 GPTA0 Input 22 Reserved O3 P1.7 I/O0 IN23 I OUT23 O1 GPTA0 Output 23 OUT79 O2 GPTA0 Output 79 A1/ PU Port 1 General Purpose I/O Line 7 GPTA0 Input 23 Reserved O3 P1.8 I/O0 IN24 I IN48 I GPTA0 Input 48 MTSR1B I SSC1 Slave Receive Input B (Slave Mode) CCU61 I CCPOS2C GPT120 I T4EUDB GPT121 I T4EUDA OUT24 O1 GPTA0 Output 24 OUT48 O2 GPTA0 Output 48 MTSR1B O3 SSC1 Master Transmit Output B (Master Mode) A1+/ Port 1 General Purpose I/O Line 8 PU GPTA0 Input 24 P1.9 I/O0 IN25 I IN49 I GPTA0 Input 49 MRST1B I SSC1 Master Receive Input B (Master Mode) CCU61 I CCPOS1C GPT120 I T2EUDB GPT121 I T2EUDA OUT25 O1 GPTA0 Output 25 OUT49 O2 GPTA0 Output 49 MRST1B O3 SSC1 Slave Transmit Output B (Slave Mode) Data Sheet A1+/ Port 1 General Purpose I/O Line 9 PU GPTA0 Input 25 3-8 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 96 P1.10 I/O0 IN26 I A1+/ Port 1 General Purpose I/O Line 10 PU GPTA0 Input 26 IN50 I GPTA0 Input 50 OUT26 O1 GPTA0 Output 26 OUT50 O2 GPTA0 Output 50 SLSO17 O3 SSC1 Slave Select Output 7 P1.11 I/O0 IN27 I A1+/ Port 1 General Purpose I/O Line 11 PU GPTA0 Input 27 IN51 I GPTA0 Input 51 SCLK1B I SSC1 Clock Input B CCU61 I CCPOS0C GPT120 I T2INB GPT121 I T2INA OUT27 O1 GPTA0 Output 27 OUT51 O2 GPTA0 Output 51 97 73 72 71 SCLK1B O3 P1.12 I/O0 AD0EMUX0 O1 Reserved O2 - Reserved O3 - P1.13 I/O0 AD0EMUX1 O1 Reserved O2 SSC1 Clock Output B A1/ PU A1/ PU Port 1 General Purpose I/O Line 12 ADC0 External Multiplexer Control Output 0 Port 1 General Purpose I/O Line 13 ADC0 External Multiplexer Control Output 1 - Reserved O3 P1.14 I/O0 AD0EMUX2 O1 Reserved O2 - Reserved O3 - Data Sheet A1/ PU Port 1 General Purpose I/O Line 14 ADC0 External Multiplexer Control Output 2 3-9 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 117 P1.15 I/O0 BRKIN I A2/ PU Reserved O1 - Reserved O2 - Reserved O3 - BRKOUT O Break Output (controlled by OCDS module) Port 1 General Purpose I/O Line 15 Break Input Port 2 74 75 P2.0 I/O0 IN32 I CCU60 I CC62INB CCU61 I CC62INA OUT32 O1 GPTA0 Output 32 TCLK0 O2 MLI0 Transmitter Clock Output 0 CCU61 O3 CC62 P2.1 I/O0 IN33 I TREADY0A I MLI0 Transmitter Ready Input A CCU61 I CCPOS0A CCU60 I T12HRB GPT120 I T2INA GPT121 I T2INB OUT33 O1 GPTA0 Output 33 SLSO03 O2 SSC0 Slave Select Output Line 3 SLSO13 O3 SSC1 Slave Select Output Line 3 Data Sheet A2/ PU A2/ PU Port 2 General Purpose I/O Line 0 GPTA0 Input 32 Port 2 General Purpose I/O Line 1 GPTA0 Input 33 3-10 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 76 P2.2 I/O0 IN34 I A2/ PU CCU60 I CC61INB CCU61 I CC61INA OUT34 O1 GPTA0 Output 34 TVALID0A O2 MLI0 Transmitter Valid Output CCU61 O3 CC61 77 78 79 A2/ PU Port 2 General Purpose I/O Line 2 GPTA0 Input 34 P2.3 I/O0 IN35 I CCU60 I T12HRC CCU60 I T13HRC CCU61 I CCPOS2A GPT120 I T4EUDA GPT121 I T4EUDB OUT35 O1 GPTA0 Output 35 TDATA0 O2 MLI0 Transmitter Data Output Reserved O3 A2/ PU Port 2 General Purpose I/O Line 3 GPTA0 Input 35 P2.4 I/O0 IN36 I RCLK0A I MLI Receiver Clock Input A OUT36 O1 GPTA0 Output 36 CCU61 O2 COUT63 Reserved O3 - GPTA0 Input 36 P2.5 I/O0 IN37 I CCU60 I CC60INB CCU61 I CC60INA OUT37 O1 GPTA0 Output 37 RREADY0A O2 MLI0 Receiver Ready Output A CCU61 O3 CC60 Data Sheet A2/ PU Port 2 General Purpose I/O Line 4 Port 2 General Purpose I/O Line 5 GPTA0 Input 37 3-11 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 80 P2.6 I/O0 A2/ PU 81 164 160 161 162 Port 2 General Purpose I/O Line 6 IN38 I RVALID0A I MLI Receiver Valid Input A OUT38 O1 GPTA0 Output 38 CCU61 O2 COUT62 Reserved O3 - P2.7 I/O0 RDATA0A I IN39 I GPTA0 Input 39 OUT39 O1 GPTA0 Output 39 CCU61 O2 COUT60 Reserved O3 - P2.8 I/O0 SLSO04 O1 SLSO14 O2 A2/ PU A2/ PU GPTA0 Input 38 Port 2 General Purpose I/O Line 7 MLI Receiver Data Input A Port 2 General Purpose I/O Line 8 SSC0 Slave Select Output 4 SSC1 Slave Select Output 4 EN00 O3 P2.9 I/O0 SLSO05 O1 SLSO15 O2 SSC1 Slave Select Output 5 EN01 O3 MSC0 Enable Output 1 MSC0 Enable Output 0 A2/ PU Port 2 General Purpose I/O Line 9 SSC0 Slave Select Output 5 P2.10 I/O0 MRST1A I A1+/ Port 2 General Purpose I/O Line 10 PU SSC1 Master Receive Input A MRST1A O1 SSC1 Slave Transmit Output Reserved O2 - Reserved O3 - P2.11 I/O0 SCLK1A I SCLK1A O1 SSC1 Clock Output A Reserved O2 - FCLP0B O3 MSC0 Clock Output Positive B Data Sheet A1+/ Port 2 General Purpose I/O Line 11 PU SSC1 Clock Input A 3-12 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 163 P2.12 I/O0 MTSR1A I A1+/ Port 2 General Purpose I/O Line 12 PU SSC1 Slave Receive Input A MTSR1A O1 SSC1 Master Transmit Output A Reserved O2 - 165 SOP0B O3 P2.13 I/O0 SLSI11 I MSC0 Serial Data Output Positive B A1+/ Port 2 General Purpose I/O Line 13 PU SSC1 Slave Select Input 1 SDI0 I MSC0 Serial Data Input 0 CCU60 I CTRAPA CCU61 I T12HRE Reserved O1 - SLSO16 O2 SSC1 Slave Select Output 6 GPT120 O3 T6OUT P3.0 I/O0 RXD0A I REQ6 I External Request Input 6 RXD0A O1 ASC0 Output (Sync. Mode) Reserved O2 - OUT84 O3 GPTA0 Output 84 Port 3 136 135 129 P3.1 I/O0 TXD0 O1 Reserved O2 A1+/ Port 3 General Purpose I/O Line 0 PU ASC0 Receiver Input A (Async. & Sync. Mode) A1+/ Port 3 General Purpose I/O Line 1 PU ASC0 Output - OUT85 O3 P3.2 I/O0 SCLK0 I SCLK0 O1 SSC0 Clock Output (Master Mode) Reserved O2 - OUT86 O3 GPTA0 Output 86 Data Sheet GPTA0 Output 85 A1+/ Port 3 General Purpose I/O Line 2 PU SSC0 Clock Input (Slave Mode) 3-13 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 130 P3.3 I/O0 MRST0 I A1+/ Port 3 General Purpose I/O Line 3 PU SSC0 Master Receive Input (Master Mode) MRST0 O1 SSC0 Slave Transmit Output (Slave Mode) Reserved O2 - 132 126 OUT87 O3 P3.4 I/O0 MTSR0 I MTSR0 O1 SSC0 Master Transmit Output (Master Mode) Reserved O2 - GPTA0 Output 87 A2/ PU O3 P3.5 I/O0 SLSO00 O1 A1+/ Port 3 General Purpose I/O Line 5 PU SSC0 Slave Select Output 0 SLSO10 O2 SSC1 Slave Select Output 0 GPTA0 Output 88 SSC0 AND SSC1 Slave Select Output 0 P3.6 I/O0 SLSO01 O1 A1+/ Port 3 General Purpose I/O Line 6 PU SSC0 Slave Select Output 1 SLSO11 O2 SSC1 Slave Select Output 1 SLSOANDO1 O3 131 128 SSC0 Slave Receive Input (Slave Mode) OUT88 SLSOANDO0 O3 127 Port 3 General Purpose I/O Line 4 SSC0 AND SSC1 Slave Select Output 1 P3.7 I/O0 A2/ PU SLSI0 I SLSO02 O1 SSC0 Slave Select Output 2 SLSO12 O2 SSC1 Slave Select Output 2 OUT89 O3 GPTA0 Output 89 P3.8 I/O0 REQ14 I A2/ PU Port 3 General Purpose I/O Line 7 SSC0 Slave Select Input 1 Port 3 General Purpose I/O Line 8 External Request Input 14 SLSO06 O1 SSC0 Slave Select Output 6 TXD1 O2 ASC1 Transmit Output OUT90 O3 GPTA0 Output 90 Data Sheet 3-14 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 138 P3.9 I/O0 RXD1A I A1/ PU RXD1A O1 ASC1 Receiver Output A (Synchronous Mode) Reserved O2 - 137 144 143 142 Port 3 General Purpose I/O Line 9 ASC1 Receiver Input A OUT91 O3 P3.10 I/O0 REQ0 I Reserved O1 - Reserved O2 - GPTA0 Output 91 A1/ PU Port 3 General Purpose I/O Line 10 External Request Input 0 OUT92 O3 P3.11 I/O0 REQ1 I Reserved O1 - Reserved O2 - OUT93 O3 GPTA0 Output 93 GPTA0 Output 92 A1/ PU A1/ PU Port 3 General Purpose I/O Line 11 External Request Input 1 P3.12 I/O0 RXDCAN0 I RXD0B I ASC0 Receiver Input B RXD0B O1 ASC0 Receiver Output B (Synchronous Mode) Reserved O2 - Port 3 General Purpose I/O Line 12 CAN Node 0 Receiver Input OUT94 O3 P3.13 I/O0 TXDCAN0 O1 TXD0 O2 ASC0 Transmit Output OUT95 O3 GPTA0 Output 95 Data Sheet GPTA0 Output 94 A2/ PU Port 3 General Purpose I/O Line 13 CAN Node 0 Transmitter Output 3-15 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 134 P3.14 I/O0 RXDCAN1 I A1/ PU RXD1B I ASC1 Receiver Input B SDI2 I MSC0 Serial Data Input 2 RXD1B O1 ASC1 Receiver Output B (Synchronous Mode) Reserved O2 - OUT96 O3 GPTA0 Output 96 133 A2/ PU Port 3 General Purpose I/O Line 14 CAN Node 1 Receiver Input P3.15 I/O0 TXDCAN1 O1 TXD1 O2 ASC1 Transmit Output OUT97 O3 GPTA0 Output 97 Port 3 General Purpose I/O Line 15 CAN Node 1 Transmitter Output Port 4 86 87 P4.0 I/O0 IN28 I IN52 I GPTA0 Input 52 RXDCAN2 I CAN Node 2 Receiver Input OUT28 O1 GPTA0 Output 28 OUT52 O2 GPTA0 Output 52 Reserved O3 - P4.1 I/O0 IN29 I IN53 I GPTA0 Input 53 OUT29 O1 GPTA0 Output 29 OUT53 O2 GPTA0 Output 53 TXDCAN2 O3 CAN Node 2 Transmitter Output Data Sheet A1+/ Port 4 General Purpose I/O Line 0 PU GPTA0 Input 28 A1+/ Port 4 General Purpose I/O Line 1 PU GPTA0 Input 29 3-16 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 88 P4.2 I/O0 IN30 I A2/ PU IN54 I GPTA0 Input 54 CCU60 I T13HRB CCU61 I CCPOS1A GPT120 I T2EUDA GPT121 I T2EUDB OUT30 O1 GPTA0 Output 30 OUT54 O2 GPTA0 Output 54 90 Port 4 General Purpose I/O Line 2 GPTA0 Input 30 EXTCLK1 O3 P4.3 I/O0 IN31 I IN55 I GPTA0 Input 55 CCU60 I T12HRE CCU61 I CTRAPA OUT31 O1 GPTA0 Output 31 OUT55 O2 GPTA0 Output 55 EXTCLK0 O3 External Clock 0 Output P5.0 I/O0 External Clock 1 Output A2/ PU Port 4 General Purpose I/O Line 3 GPTA0 Input 31 Port 5 1 A1+/ Port 5 General Purpose I/O Line 0 PU External Request Input 7 REQ7 I IN40 I GPTA0 Input 40 CCU60 I CC62INA CCU61 I CC62INB GPT120 I CAPINB GPT121 I CAPINA OUT40 O1 GPTA0 Output 40 CCU60 O2 CC62 SLSO20 O3 SSC2 Slave Select Output 0 Data Sheet 3-17 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 2 P5.1 I/O0 IN41 I A1+/ Port 5 General Purpose I/O Line 1 PU GPTA0 Input 41 OUT41 O1 GPTA0 Output 41 Reserved O2 - 3 4 5 6 SLSO21 O3 SSC2 Slave Select Output 1 P5.2 I/O0 IN42 I A1+/ Port 5 General Purpose I/O Line 2 PU GPTA0 Input 42 OUT42 O1 GPTA0 Output 42 CCU60 O2 COUT62 SLSO22 O3 SSC2 Slave Select Output 2 P5.3 I/O0 IN43 I A1+/ Port 5 General Purpose I/O Line 3 PU GPTA0 Input 43 OUT43 O1 GPTA0 Output 43 Reserved O2 - SLSO23 O3 SSC2 Slave Select Output 3 P5.4 I/O0 IN44 I A1+/ Port 5 General Purpose I/O Line 4 PU GPTA0 Input 44 SLSI2A I SSC2 Slave Select Input A OUT44 O1 GPTA0 Output 44 Reserved O2 - SLSO24 O3 SSC2 Slave Select Output 4 P5.5 I/O0 IN45 I A1+/ Port 5 General Purpose I/O Line 5 PU GPTA0 Input 45 MRST2A I SSC2 Master Receive Input A (Master Mode) OUT45 O1 GPTA0 Output 45 Reserved O2 - MRST2 O3 SSC2 Slave Transmit Output (Slave Mode) Data Sheet 3-18 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 7 P5.6 I/O0 IN46 I A1+/ Port 5 General Purpose I/O Line 6 PU GPTA0 Input 46 MTSR2A I SSC2 Slave Receive Input (Slave Mode) OUT46 O1 GPTA0 Output 46 Reserved O2 - MTSR2 O3 SSC2 Master Transmit Output (Master Mode) P5.7 I/O0 IN47 I A1+/ Port 5 General Purpose I/O Line 7 PU GPTA0 Input 47 SCLK2A I SSC2 Clock Input A (Slave Mode) OUT47 O1 GPTA0 Output 47 Reserved O2 - SCLK2 O3 SSC2 Clock Output (Master Mode) 8 13 14 15 P5.8 I/O0 CCU60 I A2/ PU CCU61 I CC61INB OUT6 O1 GPTA0 Output 6 TXDA1 O2 E-Ray Channel A transmit Data Output1) CCU60 O3 P5.9 I/O0 RXDCAN0 I Port 5 General Purpose I/O Line 8 CC61INA CC61 A2/ PU Port 5 General Purpose I/O Line 9 CAN Node 0 Receiver Input OUT7 O1 GPTA0 Output 7 TXDB1 O2 E-Ray Channel B transmit Data Output1) Reserved O3 - P5.10 I/O0 OUT8 O1 TXENA O2 E-Ray Channel A transmit Data Output enable1) CCU60 O3 COUT61 Data Sheet A2/ PU Port 5 General Purpose I/O Line 10 GPTA0 Output 8 3-19 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 16 P5.11 I/O0 A2/ PU 17 18 19 Port 5 General Purpose I/O Line 11 OUT9 O1 TXENB O2 CCU60 O3 P5.12 I/O0 CCU60 I CCU61 I T12HRB GPT120 I T3INA GPT121 I T3INB OUT19 O1 GPTA0 Output 19 SLSO07 O2 SSC0 Slave Select Output 7 AD1EMUX0 O3 P5.13 I/O0 CCU60 I CCU61 I T13HRB GPT120 I T3EUDA GPT121 I T3EUDB OUT20 O1 GPTA0 Output 20 Reserved O2 - AD1EMUX1 O3 P5.14 I/O0 RXDA1 I CCU60 I CCPOS2A CCU61 I T12HRC CCU61 I T13HRC GPT120 I T4INA GPT121 I T4INB OUT36 O1 GPTA0 Output 36 Reserved O2 - AD1EMUX2 O3 ADC1 External Multiplexer Control Output 2 Data Sheet GPTA0 Output 9 E-Ray Channel B transmit Data Output enable1) COUT63 A1+/ Port 5 General Purpose I/O Line 12 PU CCPOS0A ADC1 External Multiplexer Control Output 0 A1+/ Port 5 General Purpose I/O Line 13 PU CCPOS1A ADC1 External Multiplexer Control Output 1 A1+/ Port 5 General Purpose I/O Line 14 PU E-Ray Channel A Receive Data Input 11) 3-20 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 9 P5.15 I/O0 A1+/ Port 5 General Purpose I/O Line 15 PU E-Ray Channel B Receive Data Input 11) RXDB1 I OUT37 O1 GPTA0 Output 37 Reserved O2 - TXDCAN0 O3 CAN Node 0 Transmitter Output P6.0 I/O0 FCLN0 O1 OUT80 O2 Port 6 156 157 158 159 F/ PU Port 6 General Purpose I/O Line 0 MSC0 Clock Output Negative GPTA0 Output 80 Reserved O3 P6.1 I/O0 FCLP0A O1 OUT81 O2 GPTA0 Output 81 Reserved O3 - P6.2 I/O0 SON0 O1 OUT82 O2 F/ PU F/ PU Port 6 General Purpose I/O Line 1 MSC0 Clock Output Positive A Port 6 General Purpose I/O Line 2 MSC0 Serial Data Output Negative GPTA0 Output 82 Reserved O3 P6.3 I/O0 SOP0A O1 OUT83 O2 GPTA0 Output 83 Reserved O3 - F/ PU Port 6 General Purpose I/O Line 3 MSC0 Serial Data Output Positive A Port 8 Data Sheet 3-21 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 141 P8.0 I/O0 A2/ PU 140 139 124 Port 8 General Purpose I/O Line 0 SCLK3 I CCU60 I CCPOS0C GPT120 I T3INB GPT121 I T3INA Reserved O1 - OUT48 O2 GPTA0 Output 48 SCLK3 O3 P8.1 I/O0 SSC3 Clock Input (Slave Mode) SSC3 Clock Output (Master Mode) A2/ PU Port 8 General Purpose I/O Line 1 MRST3 I CCU60 I CCPOS1C GPT120 I T3EUDB GPT121 I T3EUDA Reserved O1 - OUT49 O2 GPTA0 Output 49 MRST3 O3 P8.2 I/O0 SSC3 Master Receive Input (Master Mode) SSC3 Slave Transmit Output (Slave Mode) A2/ PU Port 8 General Purpose I/O Line 2 MTSR3 I CCU60 I CCPOS2C GPT120 I T4INB GPT121 I T4INA Reserved O1 - OUT50 O2 GPTA0 Output 50 MTSR3 O3 P8.3 I/O0 SSC3 Slave Receive Input (Slave Mode) SSC3 Master Transmit Output (Master Mode) A2/ PU Port 8 General Purpose I/O Line 3 SLSI3 I CCU60 I CC61INC CCU61 O1 CC61 OUT51 O2 GPTA0 Output 51 SLSO30 O3 SSC3 Slave Select Output 0 Data Sheet SSC3 Slave Select Input B 3-22 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 123 P8.4 I/O0 A2/ PU 82 83 84 85 89 91 Port 8 General Purpose I/O Line 4 OUT99 O1 CCU61 O2 COUT62 SLSO31 O3 SSC3 Slave Select Output 1 A2/ PU GPTA0 Output 99 P8.5 I/O0 CCU60 I OUT100 O1 GPTA0 Output 100 CCU61 O2 CC60 SLSO32 O3 SSC3 Slave Select Output 2 CC60INC P8.6 I/O0 OUT101 O1 Reserved O2 CCU61 O3 P8.7 I/O0 CCU60 I OUT102 O1 GPTA0 Output 102 Reserved O2 - CCU61 O3 P8.8 I/O0 Reserved O1 OUT56 O2 GPTA0 Output 56 SLSO33 O3 SSC3 Slave Select Output 3 P8.9 I/O0 Reserved O1 OUT57 O2 A2/ PU Port 8 General Purpose I/O Line 5 Port 8 General Purpose I/O Line 6 GPTA0 Output 101 COUT61 A2/ PU Port 8 General Purpose I/O Line 7 CC62INC CC62 A2/ PU A2/ PU Port 8 General Purpose I/O Line 8 - Port 8 General Purpose I/O Line 9 GPTA0 Output 57 SLSO34 O3 P8.10 I/O0 OUT105 O1 Reserved O2 - Reserved O3 - Data Sheet SSC3 Slave Select Output 4 A2/ PU Port 8 General Purpose I/O Line 10 GPTA0 Output 105 3-23 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 92 P8.11 I/O0 OUT106 O1 A2/ PU Reserved O2 - Reserved O3 - 100 125 P8.12 I/O0 OUT107 O1 Reserved O2 A2/ PU Port 8 General Purpose I/O Line 11 GPTA0 Output 106 Port 8 General Purpose I/O Line 12 GPTA0 Output 107 - Reserved O3 P8.13 I/O0 OUT4 O1 Reserved O2 - CCU61 O3 COUT60 P9.2 I/O0 Reserved O1 A2/ PU Port 8 General Purpose I/O Line 13 GPTA0 Output 4 Port 9 172 171 170 A1/ PU Port 9 General Purpose I/O Line 2 - OUT82 O2 GPTA0 Output 82 CCU60 O3 COUT63 P9.3 I/O0 Reserved O1 OUT83 O2 CCU60 O3 P9.4 I/O0 CCU61 I A1/ PU Port 9 General Purpose I/O Line 3 GPTA0 Output 83 COUT62 A1/ PU Port 9 General Purpose I/O Line 4 CC62INC Reserved O1 - OUT84 O2 GPTA0 Output 84 CCU60 O3 CC62 Data Sheet 3-24 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 111 P9.5 I/O0 A2/ PU 113 11 12 Port 9 General Purpose I/O Line 5 TDI I BRKIN I OCDS Break Input Reserved O1 - Reserved O2 - Reserved O3 - BRKOUT O OCDS Break Output (controlled by OCDS module) P9.6 I/O0 TDO I BRKIN I OCDS Break Input Reserved O1 - Reserved O2 - Reserved O3 - BRKOUT O OCDS Break Output (controlled by OCDS module) TDO O JTAG Serial Data Output (controlled by OCDS module) A2/ PU A1/ PU JTAG Serial Data Input Port 9 General Purpose I/O Line 6 JTAG Serial Data Output P9.7 I/O0 CCU61 I Reserved O1 - OUT87 O2 GPTA0 Output 87 CCU60 O3 CC60 P9.8 I/O0 A1/ PU Port 9 General Purpose I/O Line 7 CC60INC Port 9 General Purpose I/O Line 7 Reserved O1 OUT88 O2 GPTA0 Output 88 CCU60 O3 COUT60 - Port 10 Data Sheet 3-25 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 23 P10.0 I/O0 A2/ PU 24 25 26 Port 10 General Purpose I/O Line 0 MRST2B I MRST2 O1 SSC2 Slave Transmit Output (Slave Mode) Reserved O2 - SSC2 Master Receive Input B (Master Mode) Reserved O3 P10.1 I/O0 MTSR2B I MTSR2 O1 SSC2 Master Transmit Output (Master Mode) Reserved O2 - A2/ PU Port 10 General Purpose I/O Line 1 SSC2 Slave Receive Input B (Slave Mode) Reserved O3 P10.2 I/O0 SCLK2B I SCLK2 O1 SSC2 Clock Output (Master Mode) Reserved O2 - Reserved O3 - A2/ PU A2/ PU Port 10 General Purpose I/O Line 2 SSC2 Clock Input B (Slave Mode) P10.3 I/O0 SLSI2B I SLSO20 O1 SSC2 Slave Select Output 0 Reserved O2 - Reserved O3 - Port 10 General Purpose I/O Line 3 SSC2 Slave Select Input B Port 11 48 47 46 P11.0 I D / S Port 11 General Purpose I/O Line 02) Dig0 I Digital Input 0 AN16 I Analog Input : ADC1.CH0 3) P11.1 I D / S Port 11 General Purpose I/O Line 12) Dig1 I Digital Input 1 AN17 I Analog Input : ADC1.CH1 3) P11.2 I D / S Port 11 General Purpose I/O Line 22) Dig2 I Digital Input 2 AN18 I Analog Input : ADC1.CH2 3) Data Sheet 3-26 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 45 P11.3 I D / S Port 11 General Purpose I/O Line 32) 44 43 42 41 40 39 38 37 35 Dig3 I Digital Input 3 AN19 I Analog Input : ADC1.CH3 3) P11.4 I D / S Port 11 General Purpose I/O Line 42) Dig4 I Digital Input 4 AN20 I Analog Input : ADC1.CH4 3) P11.5 I D / S Port 11 General Purpose I/O Line 52) Dig5 I Digital Input 5 AN21 I Analog Input : ADC1.CH5 3) P11.6 I Dig6 I Digital Input 6 AN22 I Analog Input : ADC1.CH6 3) P11.7 I Dig7 I Digital Input 7 AN23 I Analog Input : ADC1.CH7 3) P11.8 I Dig8 I Digital Input 8 AN24 I Analog Input : ADC1.CH8 3) P11.9 I Dig9 I Digital Input 9 AN25 I Analog Input : ADC1.CH9 3) P11.10 I Dig10 I Digital Input 10 AN26 I Analog Input : ADC1.CH10 3) P11.11 I D / S Port 11 General Purpose I/O Line 62) D / S Port 11 General Purpose I/O Line 72) D / S Port 11 General Purpose I/O Line 82) D / S Port 11 General Purpose I/O Line 92) D / S Port 11 General Purpose I/O Line 102) D / S Port 11 General Purpose I/O Line 112) Dig11 I Digital Input 11 AN27 I Analog Input : ADC1.CH11 3) P11.12 I D / S Port 11 General Purpose I/O Line 122) Dig12 I Digital Input 12 AN28 I Analog Input : ADC1.CH12 3) Data Sheet 3-27 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 34 P11.13 I D / S Port 11 General Purpose I/O Line 132) 33 32 Dig13 I Digital Input 13 AN29 I Analog Input : ADC1.CH13 3) P11.14 I D / S Port 11 General Purpose I/O Line 142) Dig14 I Digital Input 14 AN30 I Analog Input : ADC1.CH14 3) P11.15 I D / S Port 11 General Purpose I/O Line 152) Dig15 I Digital Input 15 AN31 I Analog Input : ADC1.CH15 3) Analog Input Port 67 AN0 I D Analog Input 0: ADC0.CH0 3) 66 AN1 I D Analog Input 1: ADC0.CH1 3) 65 AN2 I D Analog Input 2: ADC0.CH2 3) 64 AN3 I D Analog Input 3: ADC0.CH3 3) 63 AN4 I D Analog Input 4: ADC0.CH4 3) 62 AN5 I D Analog Input 5: ADC0.CH5 3) 61 AN6 I D Analog Input 6: ADC0.CH6 3) 36 AN7 I D Analog Input 7: ADC0.CH7 3) 60 AN8 I D Analog Input 8: ADC0.CH8 3) 59 AN9 I D Analog Input 9: ADC0.CH9 3) 58 AN10 I D Analog Input 10: ADC0.CH10 3) 57 AN11 I D Analog Input 11: ADC0.CH11 3) 56 AN12 I D Analog Input 12: ADC0.CH12 3) 55 AN13 I D Analog Input 13: ADC0.CH13 3) 50 AN14 I D Analog Input 14: ADC0.CH14 3) 49 AN15 I D Analog Input 15: ADC0.CH15 3) 48 AN16 I D / S Analog Input 16: ADC1.CH0, Dig0 3) 47 AN17 I D / S Analog Input 17: ADC1.CH1, Dig1 3) 46 AN18 I D / S Analog Input 18: ADC1.CH2, Dig2 3) 45 AN19 I D / S Analog Input 19: ADC1.CH3, Dig3 3) Data Sheet 3-28 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 44 AN20 I D / S Analog Input 20: ADC1.CH4, Dig4 3) 43 AN21 I D / S Analog Input 21: ADC1.CH5, Dig5 3) 42 AN22 I D / S Analog Input 22: ADC1.CH6, Dig6 3) 41 AN23 I D / S Analog Input 23: ADC1.CH7, Dig7 3) 40 AN24 I D / S Analog Input 24: ADC1.CH8, Dig8 3) 39 AN25 I D / S Analog Input 25: ADC1.CH9, Dig9 3) 38 AN26 I D / S Analog Input 26: ADC1.CH10, Dig10 3) 37 AN27 I D / S Analog Input 27: ADC1.CH11, Dig11 3) 35 AN28 I D / S Analog Input 28: ADC1.CH12, Dig12 3) 34 AN29 I D / S Analog Input 29: ADC1.CH13, Dig13 3) 33 AN30 I D / S Analog Input 30: ADC1.CH14, Dig14 3) 32 AN31 I D / S Analog Input 31: ADC1.CH15, Dig15 3) 31 AN32 I D Analog Input 32: FADC_FADIN0P 4) 30 AN33 I D Analog Input 33: FADC_FADIN0N 4) 29 AN34 I D Analog Input 34: FADC_FADIN1P 4) 28 AN35 I D Analog Input 35: FADC_FADIN1N 4) 54 VDDM VSSM VAREF0 VAGND0 VDD - - ADC Analog Part Power Supply (3.3V - 5V) - - ADC Analog Part Ground - - ADC0 and ADC1 Reference Voltage - - ADC Reference Ground - - Digital Core Power Supply (1.3V) VDDP - - Port Power Supply (3.3V) 53 52 51 10, 215), 68, 105, 153 20, 69, 106, 154 Data Sheet 3-29 V1.2, 2014-06 TC1728 Pinning Table 3-1 Pin Definitions and Functions (PG-LQFP-176-6 Package) (cont’d) Pin Symbol Ctrl. Type Function 22, 70, 107, 155 V5 - - EVR Power Supply (5V) 27 VPDG - - EVR Pass Device Gate If this pin is connected to ground, the internal pass devices are used and the external pass device bypassed. 101, 104 VSS - - Digital Ground 102 XTAL1 I Main Oscillator Input 103 XTAL2 O Main Oscillator Output 112 TMS I A2/ PD JTAG State Machine Control Input DAP1 I/O 114 TRST I A1/ PD JTAG Reset Input 115 TCK I I A1/ PD JTAG Clock Input DAP0 118 TESTMODE I I/PU Test Mode Select Input 120 ESR1 I/O A2/ PD External System Request Reset Input 1 121 PORST I I/PU Power On Reset 122 ESR0 I/O A2 External System Request Reset Input 0 Default configuration during and after reset is open-drain driver. The driver drives low during power-on reset. Device Access Port Line 1 Device Access Port Line 0 1) Only applicable for SAK-TC1728F-192F133HR. 2) Analog input overlayed with digital input functionality. The related port logic is used to configure the input as either analog input (default after reset) or digital input. The related port logic supports only the port input features as the connected pads are input only pads. 3) IOZ1 valid for this pin is the parameter with overlayed = No in the ADC parameter table. 4) IOZ1 valid for this pin is the parameter with overlayed = Yes in the ADC parameter table. 5) For the emulation device (ED), this pin is bonded to VDDSB (ED Stand By RAM supply). In the production devide device, this pin is bonded to a VDD pad. Data Sheet 3-30 V1.2, 2014-06 TC1728 Pinning Legend for Table 3-1 Column “Ctrl.”: I = Input (for GPIO port lines with IOCR bit field selection PCx = 0XXXB) O = Output O0 = Output with IOCR bit field selection PCx = 1X00B O1 = Output with IOCR bit field selection PCx = 1X01B (ALT1) O2 = Output with IOCR bit field selection PCx = 1X10B(ALT2) O3 = Output with IOCR bit field selection PCx = 1X11(ALT3) Column “Type”: A1 = Pad class A1 (LVTTL) A1+ = Pad class A1+ (LVTTL) A2 = Pad class A2 (LVTTL) F = Pad class F (LVDS/CMOS) D = Pad class D (ADC) I = Pad class I (LVTTL) S = Pad class S (CMOS) PU = with pull-up device connected during reset (PORST = 0) PD = with pull-down device connected during reset (PORST = 0) TR = tri-state during reset (PORST = 0) Data Sheet 3-31 V1.2, 2014-06 TC1728 Pinning Data Sheet 3-32 V1.2, 2014-06 TC1728 Identification Registers 4 Identification Registers The Identification Registers uniquely identify the device. Table 2 SAK-TC1728N-192F133HL Identification Registers Short Name Value Address Stepping CBS_JDPID 0000 6350H F000 0408H AB CBS_JTAGID 101D 0083H F000 0464H AB SCU_CHIPID 0300 9C01H F000 0640H AB SCU_MANID 0000 1820H F000 0644H AB SCU_RTID 0000 0001H F000 0648H AB Table 3 SAK-TC1728N-192F133HR Identification Registers Short Name Value Address Stepping CBS_JDPID 0000 6350H F000 0408H AC CBS_JTAGID 101D 0083H F000 0464H AC SCU_CHIPID 8300 9C01H F000 0640H AC SCU_MANID 0000 1820H F000 0644H AC SCU_RTID 0000 0002H F000 0648H AC Table 4 SAK-TC1728F-192F133HR Identification Registers Short Name Value Address Stepping CBS_JDPID 0000 6350H F000 0408H AC CBS_JTAGID 101D 0083H F000 0464H AC SCU_CHIPID 8300 AD01H F000 0640H AC SCU_MANID 0000 1820H F000 0644H AC SCU_RTID 0000 0002H F000 0648H AC Table 5 SAK-TC1728F-192F133HL Identification Registers Short Name Value Address Stepping CBS_JDPID 0000 6350H F000 0408H AB CBS_JTAGID 101D 0083H F000 0464H AB SCU_CHIPID 0300 AD01H F000 0640H AB Data Sheet 4-1 V1.2, 2014-06 TC1728 Identification Registers Table 5 SAK-TC1728F-192F133HL Identification Registers (cont’d) Short Name Value Address Stepping SCU_MANID 0000 1820H F000 0644H AB SCU_RTID 0000 0001H F000 0648H AB Data Sheet 4-2 V1.2, 2014-06 TC1728 Electrical Parameters 5 Electrical Parameters This specification provides all electrical parameters of the TC1728. 5.1 General Parameters 5.1.1 Parameter Interpretation The parameters listed in this section partly represent the characteristics of the TC1728 and partly its requirements on the system. To aid interpreting the parameters easily when evaluating them for a design, they are marked with an two-letter abbreviation in column “Symbol”: • • CC Such parameters indicate Controller Characteristics which are a distinctive feature of the TC1728 and must be regarded for a system design. SR Such parameters indicate System Requirements which must provided by the microcontroller system in which the TC1728 designed in. Data Sheet 5-1 V1.2, 2014-06 TC1728 Electrical Parameters 5.1.2 Pad Driver and Pad Classes Summary This section gives an overview on the different pad driver classes and its basic characteristics. More details (mainly DC parameters) are defined in the Section 5.2.1. Table 6 Pad Driver and Pad Classes Overview Class Power Type Supply A F 3.3 V 3.3 V LVTTL I/O, LVTTL outputs Sub Class Speed Load Grade A1 6 MHz (e.g. GPIO) Leakage1) 150°C 100 pF 500 nA Termination No A1+ (e.g. serial I/Os) 25 MHz 50 pF 1 μA Series termination recommended A2 (e.g. serial I/Os) 40 MHz 50 pF 3 μA Series termination recommended LVDS – 50 MHz – – 2) CMOS – 50 MHz – – Parallel termination, 100 Ω ± 10% DE 5V ADC – – – – I 3.3 V LVTTL (input only) – – – – 1) Two values are given: for TJ = 150 °C and a 50% higher value for TJ = 160 °C. 2) In applications where the LVDS pins are not used (disabled), these pins must be either left unconnected, or properly terminated with the differential parallel termination of 100 Ω ± 10%. Data Sheet 5-2 V1.2, 2014-06 TC1728 Electrical Parameters 5.1.3 Absolute Maximum Ratings Stresses above the values listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Table 7 Absolute Maximum Rating Parameters Parameter Symbol Values Min. Typ. Max. Storage temperature TST Voltage at 1.3 V power supply VDD pins with respect to VSS Voltage at 3.3 V power supply VDDP SR pins with respect to VSS Voltage at 5 V power supply VDDM pins with respect to VSS Voltage on any Class A input VIN Unit Note / Test Con dition SR -65 – 160 °C – SR – – 2.0 V – – – 4.33 V – SR – – 7.0 V – SR -0.6 – VDDP + 0.5 V or max. 4.33 Whatever is lower -0.6 – 7.0 V – Voltage on any shared Class VAINF -0.6 – D analog input pin with respect to VSSAF, if the FADC SR is switched through to the pin. 7.0 V – Input current on any pin during overload condition pin and dedicated input pins with respect to VSS Voltage on any Class D analog input pin with respect to VAGND VAIN VAREFx SR IIN -10 – +10 mA Absolute maximum sum of all IIN input circuit currents for one port group during overload condition1) -75 – +75 mA Absolute maximum sum of all ΣIIN input circuit currents during overload condition – – |200| mA Data Sheet 5-3 V1.2, 2014-06 TC1728 Electrical Parameters 1) The port groups are defined in Table 12. Data Sheet 5-4 V1.2, 2014-06 TC1728 Electrical Parameters 5.1.4 Pin Reliability in Overload When receiving signals from higher voltage devices, low-voltage devices experience overload currents and voltages that go beyond their own IO power supplies specification. Table 8 defines overload conditions that will not cause any negative reliability impact if all the following conditions are met: • • full operation life-time (24000 h) is not exceeded Operating Conditions are met for – pad supply levels (VDDP or VDDM) – temperature If a pin current is out of the Operating Conditions but within the overload parameters, then the parameters functionality of this pin as stated in the Operating Conditions can no longer be guaranteed. Operation is still possible in most cases but with relaxed parameters. Note: An overload condition on one or more pins does not require a reset. Table 8 Overload Parameters Parameter Min. Typ. Max. Unit Note / Test Con dition Input current on any digital pin IIN during overload condition except LVDS pins -5 mA Input current on LVDS pins IINLVDS IING -3 – +3 mA -70 – +70 mA IINANA IINSAS -3 – +3 mA -15 – +15 mA ΣIINS -100 – 100 mA Absolute sum of all input circuit currents for one port group during overload condition1) Input current on analog pins Absolute sum of all analog input currents for analog inputs of a single ADC during overload condition Absolute sum of all input circuit currents during overload condition Symbol Values – +5 1) The port groups are defined in Table 12. Note: FADC input pins count as analog pin as they are overlayed with an ADC pins. Data Sheet 5-5 V1.2, 2014-06 TC1728 Electrical Parameters Table 9 Pad Type A1 / A1+ / F A2 LVDS D/S Table 10 Pad Type A1 / A1+ / F A2 LVDS D/S PN-Junction Characterisitics for positive Overload IIN = 3 mA UIN = VDDP + 0.6 V UIN = VDDP + 0.5 V UIN = VDDP + 0.7 V UIN = VDDM + 0.6 V IIN = 5 mA UIN = VDDP + 0.7 V UIN = VDDP + 0.6 V - PN-Junction Characterisitics for negative Overload IIN = -3 mA UIN = VSS - 0.6 V UIN = VSS - 0.5 V UIN = VSS - 0.7 V UIN = VSSM - 0.6 V IIN = -5 mA UIN = VSS - 0.7 V UIN = VSS - 0.6 V - Note: A series resistor at the pin to limit the current to the maximum permitted overload current is sufficient to handle failure situations like short to battery without having any negative reliability impact on the operational life-time. Data Sheet 5-6 V1.2, 2014-06 TC1728 Electrical Parameters 5.1.5 Operating Conditions The following operating conditions must not be exceeded in order to ensure correct operation and reliability of the TC1728. All parameters specified in the following tables refer to these operating conditions, unless otherwise noticed. Digital supply voltages applied to the TC1728 from external must be static regulated voltages which allow a typical voltage swing of ± 5 %. All parameters specified in the following tables refer to these operating conditions (Table 11), unless otherwise noticed in the Note / Test Condition column. Table 11 Operating Conditions Parameters Parameter Symbol Values Min. Overload coupling factor for analog inputs, negative KOVAN Overload coupling factor for analog inputs, positive KOVAP CPU Frequency fCPU fFPI fLMB fPCP IID CC − Unit Typ Max. . − IOV≥ -2 mA; IOV≤ 0 mA; analog 0.0001 pad= 5.0 V CC − − IOV≥ 0 mA; IOV≤ 3 mA; analog 0.00001 pad= 5.0 V SR − − 133 MHz − − 110 MHz SR − − 133 MHz SR − − 133 MHz SR -1 − 1 mA SR -5 − 5 mA Absolute sum of ΣISC_D CC − short circuit currents of the device − 100 mA Absolute sum of ΣISC_PG CC − short circuit currents per pin group − 70 mA Ambient Temperature − 125 °C FPI Frequency LMB Frequency PCP Frequency Inactive device pin current Short circuit current of digital outputs1) Data Sheet Note / Test Condition ISC TA SR SR -40 5-7 All power supply voltages VDDx = 0 V1.2, 2014-06 TC1728 Electrical Parameters Table 11 Operating Conditions Parameters Parameter Symbol Values Min. Unit Typ Max. . Note / Test Condition SR -40 − 160 °C Core Supply Voltage VDD SR 1.17 1.3 1.432) V ADC analog supply voltage VDDM SR 2.97 5.0 5.53) V EVR supply voltage V5 4.00 5.0 5.5 V 5.0V single supply 2.97 3.3 3.63 V 3.3V single supply Only required if externally supplied5) Junction temperature TJ Digital supply voltage VDDP for IO pads SR SR 2.97 4) 3.3 3.63 V − − V VDDP voltage to ensure defined pad states6) VDDPPA CC 0.65 Digital ground voltage VSS SR 0 − − V Analog ground voltage for VDDM VSSM SR -0.1 0 0.1 V Only required if externally supplied5) 1) Applicable for digital outputs. 2) Voltage overshoot to 1.7V is permissible at Power-Up and PORST low, provided the pulse duration is less than 100 μs and the cumulated sum of the pulses does not exceed 1 h. 3) Voltage overshoot to 6.5V is permissible at Power-Up and PORST low, provided the pulse duration is less than 100 μs and the cumulated sum of the pulses does not exceed 1 h. 4) Voltage overshoot to 4.0V is permissible at Power-Up and PORST low, provided the pulse duration is less than 100 μs and the cumulated sum of the pulses does not exceed 1 h. 5) No external inductive load permissable if EVR is used. 6) This parameter is valid under the assumption the PORST signal is constantly at low level during the powerup/power-down of VDDP. Table 12 Pin Groups for Overload / Short-Circuit Current Sum Parameter Group Pins 1 P0.15, P5.[7:0], P5.[15:8], P9.[8:7], P10.[3:0] 2 P0.[14:0], P2.[13:8], P3.[1:0], P3.[4:3], P3.7, P3.[15:9], P6.[3:0], P8.[2:0], P9.[4:2] Data Sheet 5-8 V1.2, 2014-06 TC1728 Electrical Parameters Table 12 Pin Groups for Overload / Short-Circuit Current Sum Parameter (cont’d) Group Pins 3 P1.[1:0], P1.[7:5], P1.15, P3.2, P3.[6:5], P3.8, P8.[4:3], P8.13, P9.[6:5] 4 P1.[4:2], P1.[14:8], P2.[7:0], P4.[3:0], P8.[12:5] Data Sheet 5-9 V1.2, 2014-06 TC1728 Electrical Parameters 5.2 DC Parameters 5.2.1 Input/Output Pins Table 13 Standard_Pads Parameters Parameter Symbol Values Min. Typ. Max. Unit Note / Test Condition TA= 25 °C; f= 1 MHz Vi≥ 0.6 x VDDP V Vi≥ 0.36 x VDDP V Vi≤ 0.6 x VDDP V Vi≤ 0.36 x VDDP V Pin capacitance (digital inputs/outputs) CIO CC − − 10 pF Pull-down current |IPDL| CC − − 150 μA 10 − − μA 10 − − μA − − 100 μA − − 10 ns only PORST pin 120 − − ns only PORST pin Pull-Up current Spike filter always blocked pulse duration |IPUH| CC tSF1 CC Spike filter pass-through tSF2 CC pulse duration Table 14 Standard_Pads Class_A1 Parameter Symbol Values Min. Typ. Unit Max. HYSA CC 0.1 x − VDDP Input Leakage Current IOZA1 CC -500 − − V 500 nA -750 − 750 nA Input Hysteresis for pads of all A classes1) Class A1 Ratio Vil/Vih, A1 pads Data Sheet 0.6 VILA1 / VIHA1 CC − 5-10 Note / Test Condition Vi≤ VDDP V; Vi≥ 0 V; -40°C ≤ TJ ≤ 150°C Vi≤ VDDP V; Vi≥ 0 V; 150°C < TJ ≤ 160°C − V1.2, 2014-06 TC1728 Electrical Parameters Table 14 Standard_Pads Class_A1 Parameter On-Resistance of the class A1 pad, weak driver Symbol Values − 450 600 Ohm IOH> -0.5 mA; P_MOS − 210 340 Ohm IOL< 0.5 mA; N_MOS − − 155 Ohm IOH> -2 mA; P_MOS − − 110 Ohm IOL< 2 mA; N_MOS CC − − 150 ns CC CC Fall time,pad type A1 tFA1 Note / Test Condition Max. RDSONW On-Resistance of the class A1 pad, medium driver Unit Min. Typ. RDSONM CL= 20 pF; pin out driver= weak − − 50 ns CL= 50 pF; pin out driver= medium − − 140 ns CL= 150 pF; pin out − − 550 ns CL= 150 pF; pin out driver= medium driver= weak − − 18000 ns CL= 20000 pF; pin − − 65000 ns CL= 20000 pF; pin out driver= medium out driver= weak Rise time, pad type A1 tRA1 CC − − 150 ns CL= 20 pF; pin out driver= weak − − 50 ns CL= 50 pF; pin out − − 140 ns CL= 150 pF; pin out driver= medium driver= medium − − 550 ns CL= 150 pF; pin out driver= weak − − 18000 ns CL= 20000 pF; pin − − 65000 ns CL= 20000 pF; pin out driver= medium out driver= weak Data Sheet 5-11 V1.2, 2014-06 TC1728 Electrical Parameters Table 14 Standard_Pads Class_A1 Parameter Symbol Input high voltage, class A1 pads VIHA1 SR Unit Max. 0.6 x − min(VD V + 0.3, 3.6) VDDP Input low voltage, class VILA1 SR A1 pads Output voltage high, class A1 pads Values Min. Typ. Note / Test Condition DP − -0.3 0.36 x V VDDP VOHA1 CC VDDP − − V IOH≥ -1.4 mA; pin out − − V IOH≥ -2 mA; pin out - 0.4 2.4 driver= medium driver= medium VDDP − − V IOH≥ -400 μA; pin out driver= weak 2.4 − − V IOH≥ -500 μA; pin out driver= weak − − 0.4 V IOL≤ 2 mA; pin out - 0.4 Output voltage low, class A1 pads VOLA1 CC driver= medium − − 0.4 V IOL≤ 500 μA; pin out driver= weak 1) Hysteresis is implemented to avoid metastable states and switching due to internal ground bounce. It can´t be guaranteed that it suppresses switching due to external system noise. Table 15 Standard_Pads Class_A1+ Parameter Symbo l Min. Values Input Hysteresis for HYSA1 0.1 x VDDP − + CC A1+ pads 1) Input Leakage Current Class A1+ Data Sheet IOZA1+ -1000 Unit Typ Max. . − − V 1000 nA Note / Test Condition CC 5-12 V1.2, 2014-06 TC1728 Electrical Parameters Table 15 Standard_Pads Class_A1+ Parameter Symbo l Min. Values Unit Typ Max. . Note / Test Condition On-Resistance of the class A1+ pad, weak driver RDSONW − 450 600 Ohm IOH> -0.5 mA; P_MOS − 210 340 Ohm IOL< 0.5 mA; N_MOS On-Resistance of the class A1+ pad, medium driver RDSONM − − 155 Ohm IOH> -2 mA; P_MOS − − 110 Ohm IOL< 2 mA; N_MOS RDSON1+ − − 110 Ohm IOH> -2 mA; P_MOS − − 80 Ohm IOL< 2 mA; N_MOS − − 150 ns CL= 20 pF; pin out driver= weak − − 28 ns CL= 50 pF; edge= slow; pin out driver= strong − − 16 ns CL= 50 pF; edge= soft ; pin out driver= strong − − 50 ns CL= 50 pF; pin out driver= medium − − 140 ns CL= 150 pF; pin out driver= medium − − 550 ns CL= 150 pF; pin out driver= weak − − 18000 ns CL= 20000 pF; pin out driver= medium − − 65000 ns CL= 20000 pF; pin out driver= weak CC CC On-Resistance of the class A1+ pad, strong driver CC Fall time, pad type A1+ tFA1+ C Data Sheet C 5-13 V1.2, 2014-06 TC1728 Electrical Parameters Table 15 Standard_Pads Class_A1+ Parameter Rise time, pad type A1+ Symbo l Min. tRA1+ Values Unit Note / Test Condition Typ Max. . − − 150 ns CL= 20 pF; pin out driver= weak − − 28 ns CL= 50 pF; edge= slow ; pin out driver= strong − − 16 ns CL= 50 pF; edge= soft ; pin out driver= strong − − 50 ns CL= 50 pF; pin out driver= medium − − 140 ns CL= 150 pF; pin out driver= medium − − 550 ns CL= 150 pF; pin out driver= weak − − 18000 ns CL= 20000 pF; pin out driver= medium − − 65000 ns CL= 20000 pF; pin out driver= weak C C Input high voltage, Class A1+ pads VIHA1+ 0.6 x VDDP − Input low voltage, Class A1+ pads VILA1+ -0.3 Ratio Vil/Vih, A1+ pads VILA1+ / VIHA1+ SR − SR min(VD V DP + 0.3, 3.6) 0.36 x V VDDP 0.6 − − CC Data Sheet 5-14 V1.2, 2014-06 TC1728 Electrical Parameters Table 15 Standard_Pads Class_A1+ Parameter Symbo l Min. Output voltage high, VOHA1+ class A1+ pads CC Output voltage low, class A1+ pads VOLA1+ Values Unit Note / Test Condition Typ Max. . VDDP - 0.4 − − V IOH≥ -1.4 mA; pin out driver= medium VDDP - 0.4 − − V IOH≥ -1.4 mA; pin out driver= strong 2.4 − − V IOH≥ -2 mA; pin out driver= medium 2.4 − − V IOH≥ -2 mA; pin out driver= strong VDDP - 0.4 − − V IOH≥ -400 μA; pin out driver= weak 2.4 − − V IOH≥ -500 μA; pin out driver= weak − − 0.4 V IOL≤ 2 mA; pin out − − 0.4 V IOL≤ 2 mA; pin out CC driver= medium driver= strong − − 0.4 IOL≤ 500 μA; pin out V driver= weak 1) Hysteresis is implemented to avoid metastable states and switching due to internal ground bounce. It can´t be guaranteed that it suppresses switching due to external system noise. Table 16 Standard_Pads Class_A2 Parameter Symbol Input Hysteresis for A2 pads 1) HYSA2 Values Min. Data Sheet CC Unit Typ. Max. 0.1 x VDDP − 5-15 − Note / Test Condition V V1.2, 2014-06 TC1728 Electrical Parameters Table 16 Standard_Pads Class_A2 Parameter Symbol Unit Note / Test Condition 6000 nA − 3000 nA Vi< VDDP / 2 - 1 V; Vi> VDDP / 2 + 1 V; Vi≥ 0 V; Vi≤ VDDP V Vi> VDDP / 2 - 1 V; Vi< VDDP / 2 + 1 V 0.6 − − − 450 600 Ohm IOH> -0.5 mA; P_MOS − 210 340 Ohm IOL< 0.5 mA; N_MOS − − 155 Ohm IOH> -2 mA; P_MOS − − 110 Ohm IOL< 2 mA; N_MOS On-Resistance RDSON2 CC − of the class A2 pad, strong driver − − 42 Ohm IOH> -2 mA; P_MOS − 22 Ohm IOL< 2 mA; N_MOS Input Leakage IOZA2 CC current Class A2 Ratio Vil/Vih, A2 pads VILA2 / VIHA2 CC RDSONW On-Resistance of the class A2 CC pad, weak driver On-Resistance of the class A2 pad, medium driver Data Sheet RDSONM Values Min. Typ. Max. -6000 − -3000 CC 5-16 V1.2, 2014-06 TC1728 Electrical Parameters Table 16 Parameter Fall time, pad type A2 Standard_Pads Class_A2 Symbol tFA2 CC Values Min. Typ. Max. − − 150 Unit Note / Test Condition ns CL= 20 pF; pin out driver= weak − − 7 ns CL= 50 pF; edge= medium ; pin out driver= strong − − 10 ns CL= 50 pF; edge= mediumminus ; pin out driver= strong − − 3.7 ns CL= 50 pF; edge= sharp ; pin out driver= strong − − 5 ns CL= 50 pF; edge= sharpminus ; pin out driver= strong − − 16 ns CL= 50 pF; edge= soft ; pin out driver= strong − − 50 ns CL= 50 pF; pin out − − 7.5 ns CL= 100 pF; driver= medium edge= sharp ; pin out driver= strong − − 140 ns CL= 150 pF; pin out driver= medium Data Sheet 5-17 V1.2, 2014-06 TC1728 Electrical Parameters Table 16 Standard_Pads Class_A2 Parameter Symbol Values Unit Note / Test Condition 550 ns CL= 150 pF; pin 18000 ns CL= 20000 pF; Min. Typ. Max. − − − − out driver= weak pin out driver= medium − − 65000 ns CL= 20000 pF; pin out driver= weak Rise time, pad type A2 tRA2 CC − − 150 ns CL= 20 pF; pin out driver= weak − − 7.0 ns CL= 50 pF; edge= medium ; pin out driver= strong − − 10 ns CL= 50 pF; edge= mediumminus ; pin out driver= strong − − 3.7 ns CL= 50 pF; edge= sharp ; pin out driver= strong − − 5 ns CL= 50 pF; edge= sharpminus ; pin out driver= strong − − 16 ns CL= 50 pF; edge= soft ; pin out driver= strong − − 50 ns CL= 50 pF; pin out − − 7.5 ns CL= 100 pF; driver= medium edge= sharp ; pin out driver= strong − − 140 ns CL= 150 pF; pin out driver= medium Data Sheet 5-18 V1.2, 2014-06 TC1728 Electrical Parameters Table 16 Standard_Pads Class_A2 Parameter Symbol Values Unit Note / Test Condition 550 ns CL= 150 pF; pin 18000 ns CL= 20000 pF; Min. Typ. Max. − − − − out driver= weak pin out driver= medium − − 65000 ns CL= 20000 pF; pin out driver= weak VIHA2 SR Input high voltage, class A2 pads 0.6 x VDDP − Input low voltage, VILA2 SR Class A2 pads -0.3 Output voltage high, class A2 pads VDDP - 0.4 − VDDP - 0.4 − 2.4 − VOHA2 CC − min(VDDP V + 0.3, 3.6) 0.36 x V VDDP − V IOH≥ -1.4 mA; pin out driver= medium − V IOH≥ -1.4 mA; pin out driver= strong − V IOH≥ -2 mA; pin out driver= medium 2.4 − − V IOH≥ -2 mA; pin out VDDP - 0.4 − − V IOH≥ -400 μA; pin 2.4 − − V IOH≥ -500 μA; pin out driver= weak − − 0.4 V IOL≤ 2 mA; pin out driver= strong Output voltage low, class A2 pads VOLA2 CC out driver= weak driver= medium − − 0.4 V IOL≤ 2 mA; pin out driver= strong − − 0.4 V IOL≤ 500 μA; pin out driver= weak 1) Hysteresis is implemented to avoid metastable states and switching due to internal ground bounce. It can´t be guaranteed that it suppresses switching due to external system noise. Data Sheet 5-19 V1.2, 2014-06 TC1728 Electrical Parameters Table 17 Standard_Pads Class_F Parameter Input Hysteresis F Symbol 1) HYSF CC Values Unit Min. Typ. Max. 0.05 x − − V − 6000 nA Note / Test Condition VDDP Input Leakage Current Class F IOZF CC -6000 Vi≤ VDDP V; Vi≥ 0 V; Vi< VDDP / 2 1 V; Vi> VDDP / 2 +1V -3000 Ratio Vil/ Vih, F pads On-Resistance of the class F pad, medium driver − 3000 nA Vi< VDDP / 2 + 1 V; Vi> VDDP / 2 -1V − − − 175 Ohm IOH> -2 mA; P_MOS − − 160 Ohm IOL< 2 mA; N_MOS VILF / VIHF CC 0.6 RDSONM CC − Fall time, pad type F, CMOS mode tFF CC − − 60 ns CL= 50 pF Rise time, pad type F, CMOS mode tRF CC − − 60 ns CL= 50 pF Input high voltage, pad class F, CMOS mode VIHF SR 0.6 x − VDDP Input low voltage, Class VILF SR F pads, CMOS mode Output high voltage, class F pads, CMOS mode VOHF CC Output low voltage, class F pads, CMOS mode VOLF CC -0.3 min(V V + 0.3, 3.6) DDP − 0.36 x V VDDP VDDP - − − V IOH≥ -1.4 mA 2.4 − − V − − 0.4 V IOH≥ -2 mA IOL≤ 2 mA 0.4 1) Hysteresis is implemented to avoid metastable states and switching due to internal ground bounce. It can´t be guaranteed that it suppresses switching due to external system noise. Data Sheet 5-20 V1.2, 2014-06 TC1728 Electrical Parameters Table 18 Standard_Pads Class_I Parameter Symbol Values Unit Note / Test Condit ion Min. Typ. Max. 0.1 x − − V CC -1000 − 1000 nA -40°C ≤ TJ ≤ 150°C -1500 − 1500 nA 150°C < TJ ≤ 160°C − − − min(VD V DP + 0.3, 3.6) − 0.36 x Input Hysteresis Class I1) HYSI CC VDDP Input Leakage Current Ratio between low and high input threshold IOZI VILI / VIHI CC 0.6 Input high voltage, class I VIHI pins SR 0.6 x Input low voltage, Class I VILI pads SR -0.3 VDDP V VDDP 1) Hysteresis is implemented to avoid metastable states and switching due to internal ground bounce. It can´t be guaranteed that it suppresses switching due to external system noise. LVDS parameter are valid for VDD = 1.235 V to 1.365 V; VDDP = 3.135 V to 3.465 V. Table 19 LVDS_Pads Parameters Parameter Symbol Values Unit Min. Typ. Max. Note / Test Condition Output impedance, pad class F, LVDS mode RO CC 40 − 140 Ohm Fall time, pad type LVDS tFL CC − − 2 ns termination 100 Ω ± 1 %; Rise time, pad type LVDS tRL CC − − 2 ns termination 100 Ω ± 1 %; tSET_LVD − − 13 μs termination 100 Ω ± 1 % − 400 mV termination 100 Ω ± 1 % Pad set-up time S CC Output Differential Voltage VOD CC 150 Data Sheet 5-21 V1.2, 2014-06 TC1728 Electrical Parameters Table 19 LVDS_Pads Parameters Parameter Symbol Values Min. Typ. Max. Unit Note / Test Condition Output voltage high, pad class F, LVDS mode VOH CC − − 1525 mV termination 100 Ω ± 1 % Output voltage low, pad class F, LVDS mode VOL CC − − mV termination 100 Ω ± 1 % Output Offset Voltage VOS CC 1075 − 1325 mV termination 100 Ω ± 1 % 875 Class S pad parameters are only valid for VDDM = 4.75 V to 5.25 V. Table 20 Standard_Pads Class_S Parameter Symbol Values Min. Input Hysteresis for class S pads1) HYSS CC 0.3 Input leakage current IOZS CC VIHS CC VILS CC VILSD CC Input voltage high Input voltage low VILS Delta 2) −300 Unit Typ. Max. − − V − 300 nA − − 3.6 V 1.9 − − V -50 − 50 mV Note / Test Condition Maximum input low state treshold variation over 1ms (VDDP = consta nt) 1) Hysteresis is implemented to avoid metastable states and switching due to internal ground bounce. It can´t be guaranteed that it suppresses switching due to external system noise. 2) VILSD is implemented to ensure J2716 specification. It can’t be guaranteed that it suppresses switching due to external noise. Data Sheet 5-22 V1.2, 2014-06 TC1728 Electrical Parameters 5.2.2 Analog to Digital Converters (ADCx) ADC parameter in Table 21 are valid for VDD = 1.235 V to 1.365 V; VDDM = 4.75 V to 5.25 V; TJ = 150°C. Table 21 5V ADC Parameters Parameter Symbol Values Unit Min. Typ. Max. Switched capacitance at the analog voltage inputs1) CAINSW − 9 20 pF Total capacitance of an analog input CAINTOT − 20 30 pF Switched capacitance at the positive reference voltage input2)3) CAREFSW − 15 30 pF Total capacitance of the CAREFTOT − voltage reference inputs2) CC 20 40 pF Differential Non-Linearity EADNL Error4)5)6)7) CC − 3 LSB Note / Test Condition CC CC CC -3 ADC resolution= 12bit 8) 9) Gain Error4)5)6)7) EAGAIN -3.5 − 3.5 LSB ADC resolution= 12bit 8) 9) EAINL -3 − 3 LSB ADC resolution= 12bit8) 9) EAOFF -4 − 4 LSB ADC resolution= 12bit 8) 9) fADC 4 − 110 MHz fADC= fFPI − 20 MHz 10) pC charge needs to be provided via CC Integral NonLinearity4)5)6)7) Offset Error4)5)6)7) CC CC Converter clock SR Internal ADC clock fADCI CC 1 Charge consumption per QCONV 70 conversion 8511) 100 CC VAREF0 Data Sheet 5-23 V1.2, 2014-06 TC1728 Electrical Parameters Table 21 5V ADC Parameters Parameter Input leakage at analog inputs12) Symbol IOZ1 Values Min. Typ. Max. -100 − 500 Unit Note / Test Condition nA Vi≥ 0.97 x VDDM V; Vi≤ VDDM V; CC overlayed= No -100 − 600 nA Vi≥ 0.97 x VDDM V; Vi≤ VDDM V; overlayed= Yes -500 − 100 nA -600 − 100 nA Vi≥ 0 V; Vi≤ 0.03 x VDDM V; overlayed= No Vi≤ 0.03 x VDDM V; Vi≥ 0 V; overlayed= Yes -100 − 200 nA -100 − 300 nA Vi> 0.03 x VDDM V; Vi< 0.97 x VDDM V; overlayed= No Vi> 0.03 x VDDM V; Vi< 0.97 x VDDM V; overlayed= Yes Input leakage current at Varef0 IOZ2 CC -2 − 2 μA Input leakage current at Vagnd0 IOZ3 CC -2 − 2 μA 900 1500 Ohm ON resistance of the RAIN − transmission gates in the CC analog voltage path Data Sheet 5-24 VAREF0≥ 0V; VAREF0≤ VDDM V VAGND0≥ 0V; VAGND0≤ VDDM V V1.2, 2014-06 TC1728 Electrical Parameters Table 21 5V ADC Parameters Parameter Symbol Values Min. Typ. Max. Unit Note / Test Condition ON resistance for the ADC test (pull down for AIN7) RAIN7T 180 550 900 Ohm Test feature available only for odd AINx pins Resistance of the reference voltage input path RAREF − 500 1000 Ohm 500 Ohm increased if AIN[1:0] used as reference input Broken wire detection delay against VAGND tBWG CC − − 50 13) Broken wire detection delay against VAREF tBWR CC − − 50 14) Sample time tS CC tCAL CC 2 − 257 TADCI − − 4352 cycles − 416) LSB Calibration time after bit ADC_GLOBCFG.SUCAL is set Total Unadjusted Error5)6)15) CC CC TUE CC -4 Wakeup time from analog tAWAF powerdown, fast mode CC − − 5 μs Wakeup time from analog tAWAS powerdown, slow mode CC − − 10 μs VSSM - − VAREF0 V − VDDM/2 VAREF0 V VDDM + V Analog reference ground2) Analog input voltage Analog reference voltage2) VAGND0 SR VAIN SR VAREF0 SR Analog reference voltage VAREF0 range5)6)2) VAGND0 SR Data Sheet 0.05 VAGND0 VAGND0 - − + VDDM/2 VDDM/2 5-25 ADC resolution= 12bit 0.0517) 18) − VDDM + V 0.05 V1.2, 2014-06 TC1728 Electrical Parameters 1) The sampling capacity of the conversion C-network is pre-charged to VAREF/2 before the sampling moment. Because of the parasitic elements the voltage measured at AINx can deviate from VAREF/2. 2) Applies to AINx, when used as auxiliary reference input. 3) This represents an equivalent switched capacitance. This capacitance is not switched to the reference voltage at once. Instead smaller capacitances are successively switched to the reference voltage. 4) The sum of DNL/INL/GAIN/OFF errors does not exceed the related TUE total unadjusted error. 5) If the analog reference voltage range is below VDDM but still in the defined range of VDDM / 2 and VDDM is used, then the ADC converter errors increase. If the reference voltage is reduced by the factor k (k<1), TUE,DNL,INL,Gain, and Offset errors increase also by the factor 1/k. 6) If a reduced analog reference voltage between 1V and VDDM / 2 is used, then there are additonal decrease in the ADC speed and accuracy. 7) If the analog reference voltage is > VDDM, then the ADC converter errors increase. 8) For 10-bit conversions the error value must be multiplied with a factor 0.25. 9) For 8-bit conversions the error value must be multiplied with a factor 0.0625. 10) If the alternate reference is used or fADCI is more than 16 MHz, the accuracy of the ADC may decrease. 11) For a conversion time of 1 µs a rms value of 85µA result for IAREF0. 12) The leakage current definition is a continous function,as shown in figure ADCx Analoge Input Leakage. The numerical values defined determine the characteristic points of the given countinuous linear approximation they do not define step function. 13) The broken wire detection delay against VAGND is measured in numbers of consecutive precharge cycles at a conversion rate of not more than 250μs. Results below 10% (199H). 14) The broken wire detection delay against VAREF is measured in numbers of consecutive precharge cycles at a conversion rate of not more than 10μs. This function is influenced by leakage current, in particular at high temperature.Results above 60% (999H). 15) Measured without noise. 16) For 10-bit conversion the TUE is ±2LSB; for 8-bit conversion the TUE is ±1LSB 17) A running conversion may become inexact in case of violating the normal conditions (voltage overshoot). 18) If the reference voltage VAREF increase or the VDDM decrease, so that VAREF = (VDDM + 0.05V to VDDM + 0.07V), then the accuracy of the ADC decrease by 4LSB12. ADC parameter in Table 22 are valid for VDD = 1.235 V to 1.365 V; VDDM = 3.135 V to 3.465 V; TJ = 150°C. Table 22 3.3V ADC Parameters Parameter Symbo l Min. Switched capacitance at the analog voltage inputs1) CAINSW Total capacitance of an analog input CAINTOT − Data Sheet Values Unit Typ. Max. − 9 20 pF 20 30 pF Note / Test Condition CC CC 5-26 V1.2, 2014-06 TC1728 Electrical Parameters Table 22 3.3V ADC Parameters Parameter Symbo l Min. Values Unit Typ. Max. − 15 30 pF Total capacitance of the CAREFTO − voltage reference inputs2) T CC 20 40 pF Differential Non-Linearity EADNL Error4)5)6)7) CC − 4 LSB Switched capacitance at the positive reference voltage input2)3) CAREFS W Note / Test Condition CC -4 ADC resolution= 12bit 8) 9) 4)5)6)7) EAGAIN -3.5 − 3.5 LSB ADC resolution= 12bit 8) 9) EAINL -4 − 4 LSB ADC resolution= 12bit8) 9) EAOFF -4 − 4 LSB ADC resolution= 12bit 8) 9) fADC 4 − 110 MHz fADC= fFPI Internal ADC clock fADCI 1 − 20 MHz 10) Charge consumption per conversion11) QCONV − − 70 pC charge needs to be provided via Gain Error CC Integral NonLinearity4)5)6)7) Offset Error4)5)6)7) CC CC Converter clock SR CC CC VAREF0 Data Sheet 5-27 V1.2, 2014-06 TC1728 Electrical Parameters Table 22 3.3V ADC Parameters Parameter Input leakage at analog inputs12) Symbo l Min. IOZ1 Values Unit Note / Test Condition nA Vi≥ 0.97 x VDDM V; Vi≤ VDDM V; Typ. Max. − -100 500 C C overlayed= No − -100 600 nA Vi≥ 0.97 x VDDM V; Vi≤ VDDM V; overlayed= Yes -500 − 100 nA -600 − 100 nA Vi≥ 0 V; Vi≤ 0.03 x VDDM V; overlayed= No Vi≤ 0.03 x VDDM V; Vi≥ 0 V; overlayed= Yes -100 − 200 nA -100 − 300 nA Vi> 0.03 x VDDM V; Vi< 0.97 x VDDM V; overlayed= No Vi> 0.03 x VDDM V; Vi< 0.97 x VDDM V; overlayed= Yes Input leakage current at Varef IOZ2 CC -2 − 2 μA VAREF0≤ VDDM V Input leakage current at Vagnd IOZ3 CC -2 − 2 μA VAGND0≤ VDDM V ON resistance of the RAIN transmission gates in the C analog voltage path C − 3500 9000 Ohm ON resistance for the ADC test (pull down for AIN7) 180 800 Ohm Data Sheet RAIN7T CC 5-28 1800 Test feature available only for odd AINx pins V1.2, 2014-06 TC1728 Electrical Parameters Table 22 3.3V ADC Parameters Parameter Symbo l Min. Values Unit Note / Test Condition 500 Ohm increased if AIN[1:0] used as reference input Typ. Max. Resistance of the reference voltage input path RAREF − 1700 3000 Ohm Broken wire detection delay against VAGND tBWG − − 50 13) Broken wire detection delay against VAREF tBWR CC − − 50 14) Sample time tS CC 2 tCAL CC − − 257 TADCI − 4352 cycles -4.5 − 4.516) LSB Calibration time after bit ADC_GLOBCFG.SUCAL is set CC CC Total Unadjusted Error5)6)15) TUE Analog reference ground2) VAGND0 VSSM - − Analog input voltage VAIN SR VAGND0 VAREF0 VAGND0 − Analog reference voltage2) CC SR SR 0.05 VAREF0 V - − + VDDM/2 Analog reference voltage VAREF0 - VDDM/2 range5)6)2) VAGND0 ADC resolution= 12bit VDDM/2 VAREF0 V VDDM + V 0.0517) 18) − VDDM + V 0.05 SR 1) The sampling capacity of the conversion C-network is pre-charged to VAREF/2 before the sampling moment. Because of the parasitic elements the voltage measured at AINx can deviate from VAREF/2. 2) Applies to AINx, when used as auxiliary reference input. 3) This represents an equivalent switched capacitance. This capacitance is not switched to the reference voltage at once. Instead smaller capacitances are successively switched to the reference voltage. 4) The sum of DNL/INL/GAIN/OFF errors does not exceed the related TUE total unadjusted error. 5) If the analog reference voltage range is below VDDM but still in the defined range of VDDM / 2 and VDDM is used, then the ADC converter errors increase. If the reference voltage is reduced by the factor k (k<1), TUE,DNL,INL,Gain, and Offset errors increase also by the factor 1/k. Data Sheet 5-29 V1.2, 2014-06 TC1728 Electrical Parameters 6) If a reduced analog reference voltage between 1V and VDDM / 2 is used, then there are additonal decrease in the ADC speed and accuracy. 7) If the analog reference voltage is > VDDM, then the ADC converter errors increase. 8) For 10-bit conversions the error value must be multiplied with a factor 0.25. 9) For 8-bit conversions the error value must be multiplied with a factor 0.0625. 10) If the alternate reference is used, or fADCI is more than 16 MHz, or STC is lower than 8, the accuracy of the ADC may decrease. 11) QCONV is calculated as QCONV = CAREF*VAREF. 12) The leakage current definition is a continous function,as shown in figure ADCx Analoge Input Leakage. The numerical values defined determine the characteristic points of the given countinuous linear approximation they do not define step function. 13) The broken wire detection delay against VAGND is measured in numbers of consecutive precharge cycles at a conversion rate of not more than 250μs. Results below 10% (199H). 14) The broken wire detection delay against VAREF is measured in numbers of consecutive precharge cycles at a conversion rate of not more than 10μs. This function is influenced by leakage current, in particular at high temperature.Results above 60% (999H). 15) Measured without noise. 16) For 10-bit conversion the TUE is ±2LSB; for 8-bit conversion the TUE is ±1LSB 17) A running conversion may become inexact in case of violating the normal conditions (voltage overshoot). 18) If the reference voltage VAREF increase or the VDDM decrease, so that VAREF = (VDDM + 0.05V to VDDM + 0.07V), then the accuracy of the ADC decrease by 4LSB12. Table 23 Conversion Time (Operating Conditions apply) Parameter Symbol Values tC Conversion time with post-calibration Conversion time without post-calibration Data Sheet Unit Note CC 2 × TADC + (4 + STC + n) × TADCI μs 2 × TADC + (2 + STC + n) × TADCI 5-30 n = 8, 10, 12 for n - bit conversion TADC = 1 / fFPI TADCI = 1 / fADCI V1.2, 2014-06 TC1728 Electrical Parameters REXT VAIN = Analog Input Circuitry RAIN, On ANx CEXT CAINTOT - CAINSW VAGNDx CAINSW RAIN7T Reference Voltage Input Circuitry RAREF, On VAREFx VAREF CAREFTOT - CAREFSW CAREFSW VAGNDx Analog_InpRefDiag Figure 3 Data Sheet ADCx Input Circuits 5-31 V1.2, 2014-06 TC1728 Electrical Parameters Ioz1 Single ADC Input 500nA 200nA 100nA -100nA VIN[VDDM%] 3% 97% 100% -500nA Ioz1 Overlayed ADC/FADC Input 600nA 300nA 100nA -100nA VIN[VDDM%] 3% 97% 100% -600nA Figure 4 Data Sheet ADCx Analog Inputs Leakage 5-32 V1.2, 2014-06 TC1728 Electrical Parameters 5.2.3 Fast Analog to Digital Converter (FADC) FADC parameter are valid for VDDM = 4.75 V to 5.25 V;TJ = 150°C. Table 24 Parameter FADC Parameters with VDDM = 5V Symbol Values Min. DNL error Typ. Max. EFDNL CC -1 − 1 -1 − Unit Note / Test Condition LSB VIN mode= differential Gain = 1, 2 1 LSB VIN mode= single ended Gain = 1, 2 − -2 2 LSB VIN mode= differential Gain = 4, 8 TJ = 150°C 1) -2.5 − 2.5 LSB VIN mode= differential Gain = 4, 8 TJ = 160°C 1) − -2 2 LSB VIN mode= single ended Gain = 4, 8 TJ = 150°C 1) -2.5 − 2.5 LSB VIN mode= single ended Gain = 4, 8 TJ = 160°C 1) Data Sheet 5-33 V1.2, 2014-06 TC1728 Electrical Parameters Table 24 FADC Parameters with VDDM = 5V Parameter GRADient error Symbol EFGRAD Values Min. Typ. Max. -5 − 5 Unit Note / Test Condition % VIN mode= CC differential ; Gain< 4 − -5 5 % VIN mode= single ended ; Gain< 4 -5.5 − 5 % VIN mode= differential ; Gain= 4 -5.5 − 5 % VIN mode= single ended ; Gain= 4 − -6 6 % VIN mode= differential ; Gain= 8 − -6 6 % VIN mode= single ended ; Gain= 8 INL error EFINL CC -4 − -4 − 4 LSB VIN mode= differential 4 LSB VIN mode= single ended Data Sheet 5-34 V1.2, 2014-06 TC1728 Electrical Parameters Table 24 FADC Parameters with VDDM = 5V Parameter Symbol Values Min. Offset error Typ. Max. EFOFF CC -90 − 90 -90 − Unit Note / Test Condition mV VIN mode= differential ; Calibration= No 90 mV VIN mode= single ended ; Calibration= No -20 − 20 mV VIN mode= differential ; Calibration= Yes 2)3) -20 − 20 mV VIN mode= single ended ; Calibration= Yes 2)3) EFREFI -80 − 80 mV Channel amplifier cutoff frequency fCOFF CC 2 − − MHz Converter clock fFADC 4 − 110 MHz fFADC= fFPI tC CC − − 21 1/ Error of common mode voltage VFAREFI/2 CC SR Conversion time Input resistance of the analog voltage path (Rn, Rp) RFAIN CC 100 − 200 kOh m μs Settling time of a channel tSET CC amplifier after changing ENN or ENP − − 5 Analog input voltage range4) VSSM − VDDP V Wakeup time from analog tFWAF CC powerdown, fast mode − − 5 μs Wakeup time from analog tFWAS CC powerdown, slow mode − − 10 μs Data Sheet VAINF SR For 10-bit fFADC conversion 5-35 V1.2, 2014-06 TC1728 Electrical Parameters Table 24 FADC Parameters with VDDM = 5V Parameter Symbol Values Unit Note / Test Condition − V Internally generated −5)6) V Internally generated Min. Typ. Max. Analog reference ground VFAGNDI CC − 0 Analog reference voltage VFAREFI CC − 3.3 1) No missing codes. 2) Calibration should be preformed at each power-up. In case of a continous operation, it should be performed minimium once per week. 3) The offser error voltage drifts over the whole temperature range maximum +-3LSB. 4) The accuracy values is valid between 5% and 90%of VAINF 5) Voltage overshoot to 4V is permissible, provided the pulse duration is less than 100 μs and the cumulated sum of the pulses does not exceed 1 h. 6) A running conversion may become inexact in case of violating the nomal operating conditions (voltage overshoots). The calibration procedure should run after each power-up, when all power supply voltages and the reference voltage have stabilized. Data Sheet 5-36 V1.2, 2014-06 TC1728 Electrical Parameters FADC Analog Input Stage RN FAINxN - VFAREF/2 VSSM + + RP FAINxP VFAREF - FADC Reference Voltage Input Circuitry (from IVR) IFAREF VFAREF VFAGND FADC _InpRefDiag Figure 5 Data Sheet FADC Input Circuits 5-37 V1.2, 2014-06 TC1728 Electrical Parameters 5.2.4 Table 25 Oscillator Pins OSC_XTAL Parameters Parameter Symbol Values Min. Unit Note / Test Condition VIN> 0 V; VIN<VDDP Typ. Max. − 25 μA 4 − 40 MHz Direct Input Mode selected 8 − 25 MHz External Crystal Mode selected Oscillator start-up time1) tOSCS CC − − 10 ms Input high voltage at XTAL12) VIHX − VDDP + V Input low voltage at XTAL1 VILX 0.3 x V Input hysteresis for XTAL1 pad3) HYSAX CC -25 Input current at XTAL1 IIX1 Input frequency fOSC SR SR 0.7 x 0.5 VDDP − SR -0.5 VDDP − − 200 mV CC 1) tOSCS is defined from the moment when VDDP = 3.13V until the oscillations reach an amplitude at XTAL1 of 0.3 * VDDP. The external oscillator circuitry must be optimized by the customer and checked for negative resistance as recommended and specified by crystral suppliers. 2) If the XTAL1 pin is driven by a crystal, reaching a minimum amplitude (peak-to-peak) of 0.3 * VDDP is necessary. 3) Hysteresis is implemented to avoid metastable states and switching due to internal ground bounce. It can´t be guaranteed that it suppresses switching due to external system noise. Note: It is strongly recommended to measure the oscillation allowance (negative resistance) in the final target system (layout) to determine the optimal parameters for the oscillator operation. Please refer to the limits specified by the crystal or ceramic resonator supplier. Data Sheet 5-38 V1.2, 2014-06 TC1728 Electrical Parameters 5.2.5 Power Supply Current The total power supply current defined below consists of leakage and switching component. Application relevant values are typically lower than those given in the following two tables and depend on the customer's system operating conditions (e.g. thermal connection or used application configurations). The operating conditions for the parameters in the following table are: VDD=1.365 V, VDDP=3.47 V, VDDM=5.1 V, fLMB=133 / 80 MHz, TJ=160 °C The realisic power pattern defines the following conditions: • • • • • • TJ=150 °C fLMB = fPCP = fCPU = 133 / 80 MHz fFPI = 66.5 / 80 MHz VDD = 1.326 V VDDP = 3.366 V VDDM = 5.1 V The max power pattern defines the following conditions: • • • • • • TJ=160 °C fLMB = fPCP = fCPU = 133 / 80 MHz fFPI = 66.5 / 80MHz VDD = 1.37 V VDDP = 3.47 V VDDM = 5.25 V Table 26 Power Supply Parameters Parameter Symbol Values Unit Note / Test Condition Min Typ. Max. . Core active mode supply current1) − − 3102) mA power pattern= max CC − − 2123) mA power pattern= realistic IDD_PORST − − 110 mA mA IDD IDD current at PORST Low CC PORST pad output current CC IDDPORST 13 − − Sum of all 1.3 V supply currents IDDSUM − − 2124) mA IDDP current at IDDP_PORS − − 6 PORST Low Data Sheet power pattern= realistic CC T mA CC 5-39 V1.2, 2014-06 TC1728 Electrical Parameters Table 26 Power Supply Parameters Parameter Symbol Values Unit Note / Test Condition Min Typ. Max. . IDDP current no pad activity, LVDS off5) IDDP CC − − IDDP_ mA including flash read current PORST + 83 − − IDDP_ mA PORST including flash programming current 6) + 62 − − IDDP_ mA PORST including flash erase verify current 6) + 917) − − 32 mA ILVDS − − 12 mA for all LVDS pads in total IV5 − − 387 mA power pattern= max; mode = 5V only with ext. pass device; SAK-TC1728F-192F133HL SAK-TC1728F-192F133HR 382 mA power pattern= max; mode = 5V only with ext. pass device; SAK-TC1728N-192F133HL SAK-TC1728N-192F133HR 292 mA power pattern= real; mode = 5V only with ext. pass device; SAK-TC1728F-192F133HL SAK-TC1728F-192F133HR 287 mA power pattern= real; mode = 5V only with ext. pass device; SAK-TC1728N-192F133HL SAK-TC1728N-192F133HR ADC 5V power supply current IDDM Current Consumption of LVDS Pad Pairs EVR Supply current CC CC CC − Data Sheet − 5-40 V1.2, 2014-06 TC1728 Electrical Parameters Table 26 Power Supply Parameters Parameter Symbol Values Unit Note / Test Condition Min Typ. Max. . Maximum power dissipation Maximum power dissipation PD − − 902 mW power pattern= max; mode = all external − − 744 mW power pattern= realistic mode = all external − − 2032 mW power pattern= max; mode = 5V only with ext. pass device; SAK-TC1728F-192F133HL SAK-TC1728F-192F133HR 2006 mW power pattern= max; mode = 5V only with ext. pass device; SAK-TC1728N-192F133HL SAK-TC1728N-192F133HR CC PD CC 8) − − 1490 mW power pattern= realistic mode = 5V only with ext. pass device; SAK-TC1728F-192F133HL SAK-TC1728F-192F133HR − − 1464 mW power pattern= realistic mode = 5V only with ext. pass device; SAK-TC1728N-192F133HL SAK-TC1728N-192F133HR 9) 1) Infineon Power Loop: CPU and PCP running, all peripherals active. The power consumption of each customer application will most probably be lower than this value, but must be evaluated separately. 2) The IDD decreases typically by 62mA if the fCPU decreases by 50MHz, at constant Tj. 3) The IDD decreases typically by 52mA if the fCPU decreases by 50MHz, at constant Tj. 4) The IDD decreases typically by 52mA if the fCPU decreases by 50MHz, at constant Tj. 5) For operations including the D-Flash the required current is always lower than the current for non-DFlash operations. 6) Relevant for the power supply dimensioning, not for thermal considerations. 7) In case of erase of Program Flash PF, internal flash array loading effects may generate transient current spikes of up to 15 mA for maximum 5 ms per flash module. 8) Maximum power dissipation for fCPU = 80 MHz and no external pass device is 1695mW. 9) Maximum power dissipation for fCPU = 80 MHz and no external pass device is 1260 mW. Data Sheet 5-41 V1.2, 2014-06 TC1728 Electrical Parameters 5.2.5.1 Calculating the 1.3 V Current Consumption The current consumption of the 1.3 V rail compose out of two parts: • • Static current consumption Dynamic current consumption The static current consumption is related to the device temperature TJ and the dynamic current consumption depends of the configured clocking frequencies and the software application executed. These two parts needs to be added in order to get the rail current consumption. (1) I 0 mA = 0, 674 --------- × e 0, 02592 × T J [ C ] C (2) mA I 0 = 3, 9 --------- × e 0, 02085 × T J [ C ] C Function 1 defines the typical static current consumption and Function 2 defines the maximum static current consumption. Both functions are valid for VDD = 1.326 V. For the dynamic current consumption using the application pattern and fLMB = fPCP = 2 * fFPI the function 4 applies: (3) mA I D y m = 0, 76 ------------- × f CPU [ MHz ] MHz For the dynamic current consumption using the application pattern and fLMB = fPCP = fFPI the function 5 applies: (4) mA I D y m = 0, 9 ------------- × f CPU [ MHz ] MHz and this finally results in (5) I DD = I 0 + I DYM Data Sheet 5-42 V1.2, 2014-06 TC1728 Electrical Parameters 5.3 AC Parameters All AC parameters are defined with maximum driver strength unless otherwise stated. 5.3.1 Testing Waveforms VD D P 90% 90% 10% 10% VSS tR tF rise_fall Figure 6 Rise/Fall Time Parameters VD D P VD D E / 2 Test Points VD D E / 2 VSS mct04881_a.vsd Figure 7 Testing Waveform, Output Delay VLoad+ 0.1 V VLoad- 0.1 V Timing Reference Points VOH - 0.1 V VOL - 0.1 V MCT04880_new Figure 8 Data Sheet Testing Waveform, Output High Impedance 5-43 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.2 Power Sequencing 5V Supply Only V 5.5V 5V 4.0V 3.63V 3.3V 2.97 1.43V 1.3V 1.17V t PORST (output) PORST (input) A B C D E t Power-Up_EVR_1.vsd Figure 9 5 V / 3.3 V / 1.3 V Power-Up/Down Sequence The events for the above points in the power-up/down sequence • • • • • A :external supplied voltage reaches operating level B: external supplied and internal generated voltages reaches operating levels C: internal generated voltage drops below operating level D: internal generated voltage resumes operating level E: external supplied voltage leaves operating level P0.4 and P0.5 should be kept at the selected setting of '0' or '1' until external supplied voltage has reached its operating level. The following list of rules applies to the power-up/down sequence: • • All ground pins VSS must be externally connected to one single star point in the system. Regarding the DC current component, all ground pins are internally directly connected. The latch-up risk is minimized if the I/O currents are limited to: – 20 mA for one pin group – AND 100 mA for the completed device I/Os Data Sheet 5-44 V1.2, 2014-06 TC1728 Electrical Parameters • • • • • – AND additionally before power-up / after power-down: 1 mA for one pin in inactive mode (0 V on all power supplies) The PORST signal may be deactivated after all VDD5, and VAREF0 power-supplies and the oscillator have reached stable operation, within the normal operating conditions. At normal power down the PORST signal should be activated within the normal operating range, and then the power supplies may be switched off. Care must be taken that all Flash write or delete sequences have been completed. In case of a power-loss at any power-supply, all power supplies must be powereddown, conforming at the same time to the rule number 2. Although not necessary, it is additionally recommended that all power supplies are powered-up/down together in a controlled way, as tight to each other as possible. Additionally, regarding the ADC reference voltage VAREF0: – VAREF0 must power-up at the same time or later then VDDM, and – VAREF0 must power-down either earlier or at latest to satisfy the condition VAREF0 < VDDM + 0.5 V. This is required in order to prevent discharge of VAREF0 filter capacitance through the ESD diodes through the VDDM power supply. In case of discharging the reference capacitance through the ESD diodes, the current must be lower than 5 mA. Data Sheet 5-45 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.3 Power Sequencing 3.3V Supply Only V 3.63V 3.3V 2.97V 1.43V 1.3V 1.17V t PORST (output) PORST (input) A B C D E t Power-Up_EVR_2.vsd Figure 10 3.3 V / 1.3 V Power-Up/Down Sequence The events for the above points in the power-up/down sequence • • • • • A :external supplied voltage reaches operating level B: external supplied and internal generated voltages reaches operating levels C: internal generated voltage drops below operating level D: internal generated voltage resumes operating level E: external supplied voltage leaves operating level P0.4 and P0.5 should be kept at the selected setting of '0' or '1' until external supplied voltage has reached its operating level. The following list of rules applies to the power-up/down sequence: • • All ground pins VSS must be externally connected to one single star point in the system. Regarding the DC current component, all ground pins are internally directly connected. The latch-up risk is minimized if the I/O currents are limited to: – 20 mA for one pin group – AND 100 mA for the completed device I/Os Data Sheet 5-46 V1.2, 2014-06 TC1728 Electrical Parameters • • • • • – AND additionally before power-up / after power-down: 1 mA for one pin in inactive mode (0 V on all power supplies) The PORST signal may be deactivated after all VDD3.3, and VAREF0 powersupplies and the oscillator have reached stable operation, within the normal operating conditions. At normal power down the PORST signal should be activated within the normal operating range, and then the power supplies may be switched off. Care must be taken that all Flash write or delete sequences have been completed. In case of a power-loss at any power-supply, all power supplies must be powereddown, conforming at the same time to the rule number 2. Although not necessary, it is additionally recommended that all power supplies are powered-up/down together in a controlled way, as tight to each other as possible. Additionally, regarding the ADC reference voltage VAREF0: – VAREF0 must power-up at the same time or later then VDDM, and – VAREF0 must power-down either earlier or at latest to satisfy the condition VAREF0 < VDDM + 0.5 V. This is required in order to prevent discharge of VAREF0 filter capacitance through the ESD diodes through the VDDM power supply. In case of discharging the reference capacitance through the ESD diodes, the current must be lower than 5 mA. Data Sheet 5-47 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.4 Power Sequencing all Voltages supplied from External V 5.5V 5V 4.5V VAREF 3.63V 3.3V 2.97V 1.43V 1.3V 1.17V 0.5V 0.5V 0.5V VDDP PORST power down Figure 11 power fail Power-Up 10.v 5 V / 3.3 V / 1.3 V Power-Up/Down Sequence P0.4 and P0.5 should be kept at the selected setting until external supplied voltage has reached its operating level. The following list of rules applies to the power-up/down sequence: • • All ground pins VSS must be externally connected to one single star point in the system. Regarding the DC current component, all ground pins are internally directly connected. At any moment in time to avoid increased latch-up risk, each power supply must be higher then any lower_power_supply - 0.5 V, or: VDD5 > VDDP - 0.5 V; VDD5 > VDD - 0.5 V;VDDP > VDD - 0.5 V, see Figure 11. – The latch-up risk is minimized if the I/O currents are limited to: – 20 mA for one pin group – AND 100 mA for the completed device I/Os – AND additionally before power-up / after power-down: 1 mA for one pin in inactive mode (0 V on all power supplies) Data Sheet 5-48 V1.2, 2014-06 TC1728 Electrical Parameters • • • • • • • During power-up and power-down, the voltage difference between the power supply pins of the same voltage (3.3 V, 1.3 V, and 5 V) with different names, that are internally connected via diodes, must be lower than 100 mV. On the other hand, all power supply pins with the same name (for example all VDDP), are internally directly connected. It is recommended that the power pins of the same voltage are driven by a single power supply. The PORST signal may be deactivated after all VDD5, VDDP, VDD, and VAREF0 power-supplies and the oscillator have reached stable operation, within the normal operating conditions. At normal power down the PORST signal should be activated within the normal operating range, and then the power supplies may be switched off. Care must be taken that all Flash write or delete sequences have been completed. At power fail the PORST signal must be activated at latest when any 3.3 V or 1.3 V power supply voltage falls 10% below the nominal level. If, under these conditions, the PORST is activated during a Flash write, only the memory row that was the target of the write at the moment of the power loss will contain unreliable content. In order to ensure clean power-down behavior, the PORST signal should be activated as close as possible to the normal operating voltage range. In case of a power-loss at any power-supply, all power supplies must be powereddown, conforming at the same time to the rules number 2 and 4. Although not necessary, it is additionally recommended that all power supplies are powered-up/down together in a controlled way, as tight to each other as possible. Additionally, regarding the ADC reference voltage VAREF0: – VAREF0 must power-up at the same time or later then VDDM, and – VAREF0 must power-down either earlier or at latest to satisfy the condition VAREF0 < VDDM + 0.5 V. This is required in order to prevent discharge of VAREF0 filter capacitance through the ESD diodes through the VDDM power supply. In case of discharging the reference capacitance through the ESD diodes, the current must be lower than 5 mA. Data Sheet 5-49 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.5 Power, Pad and Reset Timing Table 27 Reset Timings Parameters Parameter Symbo l Min. Typ. Max. Uni Note / Test Condition t − 810 μs − − 2.5 ms EVR Startup time tEVR from Supply CC ramp-up till PORST release − 860 1100 μs HWCFG pins tHDH hold time from SR ESR0 rising edge 16 / fFPI − − ns HWCFG pins tHDS setup time to CC ESR0 rising edge 0 − − ns Ports inactive after ESR0 reset active tPI − − 8/fFPI ns Ports inactive after PORST reset active5) tPIP − − 150 ns Minimum PORST tPOA active time after CC power supplies are stable at operating levels 4.5 − − ms TESTMODE / TR tPOH ST hold time from SR PORST rising edge 100 − − ns PORST rise time − − 50 ms Application Reset tB Boot Time1)2) Power on Reset Boot Time3)4) CC 150 tBP Values CC CC CC tPOR 6) SR Data Sheet 5-50 V1.2, 2014-06 TC1728 Electrical Parameters Table 27 Parameter Reset Timings Parameters Symbo l Min. Typ. Max. Uni Note / Test Condition t 0 − − ns Application Reset tPOR_APP − inactive after SR PORST deassertion − 40 7) μs TESTMODE / TR tPOS ST setup time to SR PORST rising edge Values 1) The duration of the boot time is defined between the rising edge of the internal application reset and the clock cycle when the first user instruction has entered the CPU pipeline and its processing starts. 2) The given time includes the time of the internal reset extension for a configured value of SCU_RSTCNTCON.RELSA = 0x05BE. 3) The duration of the boot time is defined between the rising edge of the PORST and the clock cycle when the first user instruction has entered the CPU pipeline and its processing starts. 4) The given time includes the internal reset extension time for the System and Application Reset which is visible through ESR0. 5) This parameter includes the delay of the analog spike filter in the PORST pad. 6) This parameter represents the additional time required to ensure that external crystal is stable and operational at PORST. 7) Application Reset is assumed not to be extended from external, otherwise the time extends by the time the Application Reset is extended. Data Sheet 5-51 V1.2, 2014-06 TC1728 Electrical Parameters V5 ‐10% V DDPPA VDDP V DDPPA VDD VDD ‐12% t BP t EVR t POA PORST t POH TRST t POH t hd t hd ESR0 t HDH t HDH t HDH HWCFG t PIP t PI t PIP t PI Pads tPI t t PI tPI PIP Pad‐state undefined Tri‐state or pull device active As programmed Figure 12 Power, Pad and Reset Timing Data Sheet 5-52 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.6 EVR Parameter Table 28 Pass device detector Parameter Symbol Values Unit Note / Test Condition VDD5≥ 4.5V; VDD5≤ 5.5V Min. Typ. Max. Pull-up current at VDPG IPU_VDPG SR 0.7 − 2.0 mA Input low voltage 0 − 1.5 V Table 29 VIL SR EVR Parameters Parameter Symbol Values Unit Note / Test Condition Min. Typ. Max. − 6.8 − µF ILOAD > 310 mA; ESR < 50mΩ;a with external pass device, additional decoupling capacitor on each supply pin − 6.8 − µF ILOAD < 250 mA; ESR < 50mΩ; additional decoupling capacitor on each supply pin CIN5 CC − Input Capacitance on 6.8 − µF depending on ext. regulator − − 2.97 V 3.3V single supply − − 4.5 V 5.0 single supply − +80 mV 4.5 ≤ VIN ≤ 5.5V; 1 mA ≤ IOUT ≤ 310mA +225 mV dI / dt = 150mA /10 ns Output COUT33 Capacitance on CC VDDP Output COUT13 Capacitance on CC VDD V5 Undervoltage VRST5 Reset threshold CC for external supply Output accuracy of EVR33 after trimming Dynamic Load Regulation of EVR33 Data Sheet ∆VOUT33 -80 CC ∆VLOREG − CC 225 33 5-53 V1.2, 2014-06 TC1728 Electrical Parameters Table 29 EVR Parameters (cont’d) Parameter Symbol Values Min. Typ. Unit Note / Test Condition dV5 / dt = 1V / ms 1 … 310mA, 4.5V … 5.5V Max. -25 − +25 mV VRST33 Undervoltage Reset threshold CC for EVR33 − − 2.97 V Current drawn EXI33 from EVR33 for SR external devices with internal pass devices. − − 30 mA No inductive loads allowed. Decoupling capacitor > 330 nF − +30 mV 2.97V ≤ VIN ≤ 3.63V; 1 mA ≤ IOUT ≤ 250mA +100 mV 5.0V/3.3V single supply, dI / dt = 150mA /10 ns 5.0V/3.3V single supply, dV5 / dt=1V / ms 1 … 250mA, 2.97V … 3.63V Dynamic Line Regulation of EVR33 ∆VLIREG CC 33 Output accuracy of EVR13 after trimming ∆VOUT13 -30 CC Dynamic Load Regulation of EVR13 − ∆VLOREG CC 100 13 Dynamic Line Regulation of EVR13 ∆VLIREG 13 CC -10 − +10 mV VRST13 Undervoltage Reset threshold CC for EVR13 − − 1.17 V Current drawn EXI13 from EVR13 for SR external devices − − 10 mA Supply ramp-up SR SR − − 50 V/ms Data Sheet 5-54 No inductive loads allowed. Decoupling capacitor > 100 nF V1.2, 2014-06 TC1728 Electrical Parameters 5.3.7 Table 30 Phase Locked Loop (PLL) PLL_SysClk Parameters Parameter Symbol Values Min. Accumulated Jitter DP PLL base frequency fPLLBASE VCO input frequency fREF fVCO VCO frequency Unit Note / Test Condition Typ. Max. CC -7 − 7 ns CC 50 200 320 MHz CC 8 − 16 MHz CC 400 − 720 MHz 14 − 200 μs N > 32 14 − 400 μs N ≤ 32 range PLL lock-in time tL CC Phase Locked Loop Operation When PLL operation is enabled and configured, the PLL clock fVCO (and with it the LMBBus clock fLMB) is constantly adjusted to the selected frequency. The PLL is constantly adjusting its output frequency to correspond to the input frequency (from crystal or clock source), resulting in an accumulated jitter that is limited. This means that the relative deviation for periods of more than one clock cycle is lower than for a single clock cycle. This is especially important for bus cycles using wait states and for the operation of timers, serial interfaces, etc. For all slower operations and longer periods (e.g. pulse train generation or measurement, lower baudrates, etc.) the deviation caused by the PLL jitter is negligible. Two formulas are defined for the (absolute) approximate maximum value of jitter Dm in [ns] dependent on the K2 - factor, the LMB clock frequency fLMB in [MHz], and the number m of consecutive fLMB clock periods. for ( K2 ≤ 100 ) ( m ≤ ( f LMB [ MHz ] ) ⁄ 2 ) and ( 1 – 0, 01 × K2 ) × ( m – 1 ) 740 D m [ ns ] = ⎛⎝ --------------------------------------------- + 5⎞⎠ × ⎛⎝ ---------------------------------------------------------------- + 0, 01 × K2⎞⎠ 0, 5 × f LMB [ MHz ] – 1 K2 × f LMB [ MHz ] else Data Sheet 740 D m [ ns ] = --------------------------------------------- + 5 K2 × f LMB [ MHz ] 5-55 (6) (7) V1.2, 2014-06 TC1728 Electrical Parameters With rising number m of clock cycles the maximum jitter increases linearly up to a value of m that is defined by the K2-factor of the PLL. Beyond this value of m the maximum accumulated jitter remains at a constant value. Further, a lower LMB-Bus clock frequency fLMB results in a higher absolute maximum jitter value. Note: The specified PLL jitter values are valid if the capacitive load per pin does not exceed CL = 20 pF with the maximum driver and sharp edge. Oscillator Watchdog (OSC_WDT) The expected input frequency is selected via the bit field SCU_OSCCON.OSCVAL. The OSC_WDT checks for too low frequencies and for too high frequencies. The frequency that is monitored is fOSCREF which is derived for fOSC. (8) f O S C R EF fO S C = ---------------------------------OSCVAL + 1 The divider value SCU_OSCCON.OSCVAL has to be selected in a way that fOSCREF is 2.5 MHz. Note: fOSCREF has to be within the range of 2 MHz to 3 MHz and should be as close as possible to 2.5 MHz. The monitored frequency is too low if it is below 1.25 MHz and too high if it is above 7.5 MHz. This leads to the following two conditions: • • Too low: fOSC < 1.25 MHz × (SCU_OSCCON.OSCVAL+1) Too high: fOSC > 7.5 MHz × (SCU_OSCCON.OSCVAL+1) Note: The accuracy is 30% for these boundaries. Data Sheet 5-56 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.8 Table 31 ERAY Phase Locked Loop (ERAY_PLL) PLL_ERAY Parameters Parameter Symbol Values Min. Unit Typ. Max. CC -0.8 − 0.8 ns DP CC -0.5 PLL Base Frequency of fPLLBASE_ERAY CC 50 − 0.5 ns 250 360 MHz VCO input frequency of fREF the ERAY PLL CC 20 − 40 MHz VCO frequency range of the ERAY PLL fVCO_ERAY CC 450 − 500 MHz PLL lock-in time tL CC 5.6 − 200 μs Accumulated jitter at SYSCLK pin DPP Accumulated_Jitter Note / Test Con dition the ERAY PLL Note: The specified PLL jitter values are valid if the capacitive load per pin does not exceed CL = 20 pF with the maximum driver and sharp edge. Data Sheet 5-57 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.9 JTAG Interface Timing The following parameters are applicable for communication through the JTAG debug interface. The JTAG module is fully compliant with IEEE1149.1-2000. Note: These parameters are not subject to production test but verified by design and/or characterization. Table 32 JTAG Parameters Parameter TCK clock period TCK high time Symbol t1 SR t2 SR t3 SR t4 SR t5 SR t6 SR Values Unit Min. Typ. Max. 25 − − ns 10 − − ns 10 − − ns − − 4 ns − − 4 ns 6.0 − − ns t7 SR 6.0 − − ns TDO valid after TCK falling t8 CC edge1) 3.0 − − ns − − 13 ns TCK low time TCK clock rise time TCK clock fall time TDI/TMS setup to TCK rising edge TDI/TMS hold after TCK rising edge Note / Test Condition TDO high impedance to valid from TCK falling edge2) t9 CC − − 14 ns CL= 20 pF CL=50 pF CL= 50 pF TDO valid output to high impedance from TCK falling edge t10 CC − − 13.5 ns CL= 50 pF TDO hold after TCK falling t18 CC edge 2 − − ns 1) The falling edge on TCK is used to generate the TDO timing. 2) The setup time for TDO is given implicitly by the TCK cycle time. Data Sheet 5-58 V1.2, 2014-06 TC1728 Electrical Parameters t1 0.9 VD D P 0.5 VD D P t5 t2 0.1 VD D P t4 t3 MC_ JTAG_ TCK Figure 13 Test Clock Timing (TCK) TCK t6 t7 t6 t7 TMS TDI t9 t8 t1 0 TDO t18 Figure 14 Data Sheet MC_JTAG JTAG Timing 5-59 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.10 DAP Interface Timing The following parameters are applicable for communication through the DAP debug interface. Note: These parameters are not subject to production test but verified by design and/or characterization. Table 33 DAP Parameters Parameter Symbol 1) tTCK SR t12 SR t13 SR t14 SR t15 SR t16 SR DAP0 clock period DAP0 high time 1) DAP0 low time DAP0 clock rise time DAP0 clock fall time DAP1 setup to DAP0 rising edge Values Unit Min. Typ. Max. 12.5 − − ns 4 − − ns 4 − − ns − − 2 ns − − 2 ns 6.0 − − ns DAP1 hold after DAP0 rising edge t17 SR 6.0 − − ns DAP1 valid per DAP0 clock period2) t19 CC 8 − − ns 10 − − ns Note / Test Condition CL= 20 pF; f= 80 MHz CL= 50 pF; f= 40 MHz 1) See the DAP chapter for clock rate restrictions in the Active::IDLE protocol state. 2) The Host has to find a suitable sampling point by analyzing the sync telegram response. t11 0.9 VD D P 0.5 VD D P t1 5 t1 2 t14 0.1 VD D P t1 3 MC_DAP0 Figure 15 Data Sheet Test Clock Timing (DAP0) 5-60 V1.2, 2014-06 TC1728 Electrical Parameters DAP0 t1 6 t1 7 DAP1 MC_ DAP1_RX Figure 16 DAP Timing Host to Device t1 1 DAP1 t1 9 MC_ DAP1_TX Figure 17 Data Sheet DAP Timing Device to Host 5-61 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.11 Peripheral Timings Note: Peripheral timings are not subjected to production test. They are verified by design / characterization. 5.3.11.1 Micro Link Interface (MLI) Timing MLI Transmitter Timing t13 t14 t10 t12 TCLKx t11 t15 t15 TDATAx TVALIDx t16 t17 TREADYx MLI Receiver Timing t23 t24 t20 RCLKx t22 t21 t25 t26 RDATAx RVALIDx t27 t27 RREADYx MLI_Tmg_2.vsd Figure 18 Data Sheet MLI Interface Timing 5-62 V1.2, 2014-06 TC1728 Electrical Parameters Note: The generation of RREADYx is in the input clock domain of the receiver. The reception of TREADYx is asynchronous to TCLKx. The MLI parameters are valid for CL = 50 pF, strong driver medium edge. Table 34 MLI Receiver Parameter Symbol RCLK clock period RCLK high time1)2) RCLK low time1)2) 3) RCLK rise time RCLK fall time3) RDATA/RVALID setup time before RCLK falling edge t20 SR t21 SR t22 SR t23 SR t24 SR t25 SR Values Unit Min. Typ. Max. 1 / fFPI − − ns − 0.5 x t20 − ns − 0.5 x t20 − ns − − 4 ns − − 4 ns 4.2 − − ns RDATA/RVALID hold time after RCLK falling edge t26 SR 2.2 − − ns RREADY output delay time t27 SR 0 − 16 ns Note / Test Condition 1) The following formula is valid: t21 + t22 = t20. 2) Min and Max values for this parameter can be derived from the typ. value by considering the other receiver timing parameters. 3) The RCLK max. input rise/fall times are best case parameters for fFPImax. For reduction of EMI, slower input signal rise/fall times can be used for longer RCLK clock periods. Table 35 MLI Transmitter Parameter Symbol TCLK clock period t10 CC Values Min. Typ. Max. Unit Note / Test Condition 2x1/ − − ns 0.45 x 0.5 x 0.55 x t10 ns t10 t10 0.45 x 0.5 x 0.55 x t10 ns t10 t10 fFPI TCLK high time1)2) TCLK low time1)2) Data Sheet t11 CC t12 CC 5-63 V1.2, 2014-06 TC1728 Electrical Parameters Table 35 MLI Transmitter Parameter Symbol Min. Typ. Max. Unit Note / Test Condition t13 CC t14 CC t15 CC − − 0.3 x t103) ns − − 0.3 x t103) ns -3 − 4.4 ns t16 SR 18 − − ns t17 SR TREADY hold time after TCLK rising edge -2 − − ns TCLK rise time TCLK fall time TDATA/TVALID output delay time TREADY setup time before TCLK rising edge Values 1) The following formula is valid: t11 + t12 = t10. 2) The min./max. TCLK low/high times t11/t12 include the PLL jitter of fSYS. Fractional divider settings must be regarded additionally to t11 / t12. 3) For high-speed MLI interface, strong driver sharp or medium edge selection (class A2 pad) is recommended for TCLK. 5.3.11.2 Micro Second Channel (MSC) Interface Timing The MSC parameters are valid for CL = 50 pF. Table 36 MSC Parameters Parameter FCLP clock period1)2) Data Sheet Symbol t40 CC Values Unit Min. Typ. Max. 2x − − TMSC3) 5-64 Note / Test Condition ns V1.2, 2014-06 TC1728 Electrical Parameters Table 36 MSC Parameters Parameter SOP4)/ENx outputs delay from FCLP4) rising edge SDI bit time Symbol t45 CC t46 CC Values Unit Note / Test Condition 5 ns ENx with strong driver and sharp (minus ) edge; LVDS mode − 5 ns ENx with strong driver and sharp (minus ) edge; CMOS mode -2 − 10 ns ENx with strong driver and medium (minus) edge 0 − 21 ns ENx with strong driver and soft edge 8x − − ns − − 200 ns − − 200 ns Min. Typ. Max. -2 − -5 TMSC SDI rise time SDI fall time t48 SR t49 SR 1) FCLP signal rise/fall times are only defined by the pad rise/fall times. 2) FCLP signal high and low can be minimum 1 / TMSC 3) TMSC = TSYS = 1 / fSYS. 4) SOP / FCLP either propagated by LVDS or by CMOS strong driver and non soft edge. Data Sheet 5-65 V1.2, 2014-06 TC1728 Electrical Parameters t40 0.9 VDDP 0.1 VDDP FCLP t45 t45 SOP EN t48 t49 0.9 VDDP 0.1 VDDP SDI t46 Figure 19 t46 MSC_Tmg_1.vsd MSC Interface Timing Note: The data at SOP should be sampled with the falling edge of FCLP in the target device. Data Sheet 5-66 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.11.3 SSC Master/Slave Mode Timing The SSC parameters are valid for CL = 50 pF, strong driver medium edge. Table 37 Parameters Parameter SCLK clock period1)2)3) Symbol t50 CC Values Unit Min. Typ. Max. 2x1/ − − ns Note / Test Conditi on fFPI MTSR/SLSOx delay from SCLK rising edge t51 CC 0 − 8 ns MRST setup to SCLK latching edge3) t52 SR 16.5 − − ns MRST hold from SCLK latching edge3) t53 SR 0 − − ns SCLK input clock period1)3) t54 SR 4x1/ − − ns SCLK input clock duty cycle t55_t54 SR 45 − 55 % MTSR setup to SCLK latching edge3)4) t56 SR 1 / fFPI +1 − − ns MTSR hold from SCLK latching edge t57 SR 1 / fFPI +5 − − ns SLSI setup to first SCLK latching edge t58 SR 1 / fFPI +5 − − ns SLSI hold from last SCLK t59 SR latching edge5) 7 − − ns MRST delay from SCLK shift edge t60 CC 0 − 16.5 ns SLSI to valid data on MRST t61 CC − − 16.5 ns fFPI 1) SCLK signal rise/fall times are the same as the rise/fall times of the pad. 2) SCLK signal high and low times can be minimum 1xT. 3) Tmin = TSYS = 1/fSYS. 4) Fractional divider switched off, internal baud rate generation used. Data Sheet 5-67 V1.2, 2014-06 TC1728 Electrical Parameters 5) For CON.PH=1 slave select must not be removed before the following shifting edge. This mean, that what ever is configured (shifting / latching first), SLSI must not be de-actived before the last trailing edge from the pair of shifting / latching edges. t50 SCLK1)2) t51 t51 MTSR1) t52 t53 Data valid 1) MRST t51 2) SLSOn 1) This timing is based on the following setup: CON.PH = CON.PO = 0. 2) The transition at SLSOn is based on the following setup: SSOTC.TRAIL = 0 and the first SCLK high pulse is in the first one of a transmission. SSC_TmgMM Figure 20 Data Sheet Master Mode Timing 5-68 V1.2, 2014-06 TC1728 Electrical Parameters t54 First latching SCLK edge First shift SCLK edge SCLK1) t55 t56 Last latching SCLK edge t55 t56 t57 Data valid 1) MTSR t57 Data valid t60 t60 1) MRST t61 SLSI t59 t58 1) This timing is based on the following setup: CON.PH = CON.PO = 0. Figure 21 Data Sheet SSC_TmgSM Slave Mode Timing 5-69 V1.2, 2014-06 TC1728 Electrical Parameters 5.3.11.4 ERAY Interface Timing The timings of this section are valid for the strong driver and either sharp edge or medium edge settings of the output drivers with CL = 25 pF. The ERAY interface is only available for SAK-TC1728F-192F133HR / SAK-TC1728F192F133HR. Last CRC Byte BSS (Byte Start Sequence) FES (Frame End Sequence) 0.7 VDD 0.3 VDD TXD t60 tsample TXD 0.9 VDD 0.1 VDD t61 t62 Last CRC Byte BSS (Byte Start Sequence) FES (Frame End Sequence) 0.7 VDD 0.3 VDD RXD t63 tsample RXD 0.7 VDD 0.3 VDD t64 t65 ERAY_TIMING Figure 22 Data Sheet ERAY Timing 5-70 V1.2, 2014-06 TC1728 Electrical Parameters 5.4 Package and Reliability 5.4.1 Package Parameters Table 38 Thermal Characteristics of the Package Device Package TC1728 PG-LQFP-176-6 RΘJCT RΘJC 1) B1) RΘJCL Unit 7.6 32.5 0.6 Note 1) K/W 1) The top and bottom thermal resistances between the case and the ambient (RTCAT, RTCAB) are to be combined with the thermal resistances between the junction and the case given above (RTJCT, RTJCB), in order to calculate the total thermal resistance between the junction and the ambient (RTJA). The thermal resistances between the case and the ambient (RTCAT, RTCAB) depend on the external system (PCB, case) characteristics, and are under user responsibility. The junction temperature can be calculated using the following equation: TJ = TA + RTJA × PD, where the RTJA is the total thermal resistance between the junction and the ambient. This total junction ambient resistance RTJA can be obtained from the upper four partial thermal resistances. Data Sheet 5-71 V1.2, 2014-06 TC1728 Electrical Parameters 5.4.2 Package Outline Figure 23 Package Outlines PG-LQFP-176-6 Table 39 Exposed pad Dimensions Ex 7.5 mm Ey 7.5 mm You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. 5.4.3 Flash Memory Parameters The data retention time of the TC1728’s Flash memory depends on the number of times the Flash memory has been erased and programmed. Data Sheet 5-72 V1.2, 2014-06 TC1728 Electrical Parameters Table 40 FLASH32 Parameters Parameter Symbol Values Min. Unit Typ. Max. Note / Test Condition tERD CC − − 31) s Program Flash Erase tERP Time per 256 KByte Sector CC − − 5 s − − 5.3 ms without reprogramming − − 15.9 ms with two reprogramming cycles − − 5.3 ms without reprogramming − − 10.6 ms with one reprogramming cycle CC 60000 − − cycles Min. data retention 5 years − 15 ms Data Flash Erase Time per Sector Program time data flash per page2) tPRD CC Program time program flash per page3) tPRP CC Data Flash Endurance NE 4) Erase suspend delay tFL_ErSusp CC − Wait time after margin change tFL_MarginDel SR 10 − − μs Program Flash Retention Time, Physical Sector5)6) tRET CC 20 − − years Max. 1000 erase/ program cycles Program Flash Retention Time, Logical Sector5)6) tRETL CC 20 − − years Max. 100 erase/ program cycles UCB Retention Time5)6) tRTU CC 20 − − years Max. 4 erase/ program cycles per UCB Wake-Up time2) tWU CC − − 270 μs Data Sheet 5-73 V1.2, 2014-06 TC1728 Electrical Parameters Table 40 FLASH32 Parameters Parameter Symbol Values Min. Typ. Unit Max. DFlash wait state configuration WSDF SR 50ns x − − PFlash wait state configuration WSPF fLMB SR 26ns x − fLMB − Note / Test Condition 1) In case of wordline oriented defects (see robust EEPROM emulation in the User's Manual) this erase time can increase by up to 100%. 2) In case the Program Verify feature detects weak bits, these bits will be programmed up to twice more. Each reprogramming takes additional 5 ms. 3) In case the Program Verify feature detects weak bits, these bits will be programmed once more. The reprogramming takes additional 5 ms. 4) Only valid when a robust EEPROM emulation algorithm is used. For more details see the User´s Manual. 5) Storage and inactive time included. 6) At average weighted junction temperature Tj = 100°C, or the retention time at average weighted temperature of Tj = 110°C is minimum 10 years, or the retention time at average weighted temperature of Tj = 150°C is minimum 0.7 years. 5.4.4 Table 41 Quality Declarations Quality Parameters Parameter Symbol Values Unit Note / Test Condition Min. Typ. Max. – – 24000 hours –2) ESD susceptibility VHBM according to Human Body Model (HBM) – – 2000 V Conforming to JESD22-A114-B ESD susceptibility VHBM1 of the LVDS pins – – 500 V – ESD susceptibility VCDM according to Charged Device Model (CDM) – – 500 V Conforming to JESD22-C101-C Moisture Sensitivity Level – – 3 – Conforming to Jedec J-STD-020C for 240°C Operation Lifetime1) Data Sheet tOP MSL 5-74 V1.2, 2014-06 TC1728 Electrical Parameters 1) This lifetime refers only to the time when the device is powered on. 2) For worst-case temperature profile equivalent to: 1200 hours at Tj = 125...160oC 3600 hours at Tj = 110...125oC 7200 hours at Tj = 100...110oC 11000 hours at Tj = 25...110oC 1000 hours at Tj = -40...25oC Data Sheet 5-75 V1.2, 2014-06 TC1728 Electrical Parameters Data Sheet 5-76 V1.2, 2014-06 TC1728 Revision History 6 Revision History Changes from V0.3 to V0.4D1 • • • • • • Operating Conditions – Added footnote 3 and 4 – Updated KOVAN and KOVAP max values – Added fCPU, fLMB, fPCP, fFPImax for SAK-TC1724F-192F133HL, SAK-TC1724F192F133HR, SAK-TC1724N-192F80HR, SAK-TC1724N-128F80HR. – Updated limits for VDD, VDDM, VDDP. – Added IIN, ΣIIN – Updated ΣISC_PG Standard Pad Class A1 – Changed RDSON1 to RDSONM, added new condition “PMOS” for 140ohms, added a new condition for “NMOS” with a max value of 100ohms – Added RDSONW – Changed min value of VIHA1 to 0.6 x VDDP – Changed min value of VILA1 / VIHA1 to 0.6 Standard Pad Class A1+ – Added HYSA1+ – Added VILA1+ / VIHA1+ – Added RDSONW, RDSONM – RDSON1+, added new condition “PMOS” for 85ohms, added a new condition for “NMOS” with a max value of 70ohms – Changed min value of VIHA1+ to 0.6 x VDDP – Deleted -2000nA to 2000nA limits for IOZA1+ Standard Pad Class A2 – Added HYSA2 – Added RDSONW, RDSONM – RDSON2, added new condition “PMOS” for 25ohms, added a new condition for “NMOS” with a max value of 20ohms – tFA2, added max 18000ns for CL=20000pF; pinout driver=medium, 65000ns for CL=20000pF;pinout driver=weak – tRA2, removed 140ns for CL=150pF;pinout driver=weak – tRA2, added 550ns for CL=150pF,pinout driver=weak, 18000ns for CL=20000pF, pinout driver=medium, 65000ns for CL=20000pF, pinoutdriver=weak Standard Pad Class F – Added HYSF – Changed min value of VIHF to 0.6 x VDDP – Added min value of VILF / VIHF as 0.6 – Added RDSONW, RDSONM – Deleted note for tFF, tRF Standard Pad Class I – Changed min value of VIHI to 0.6 x VDDP Data Sheet 6-1 V1.2, 2014-06 TC1728 Revision History • • • • • • – Changed min value of VILI / VIHI as 0.6 LVDS Pads – Removed input hysteresis F, HYSF – Added note “Parallel termination 100 Ohm +-1%” for tFL, tRL, tSET_LVDS Standard Pad Class S – Changed max value of VIHS to 3.6 – Changed min value of VILS to 2.1 – Added input leakage current, IOZS ADC parameters – Changed typ value of CAINSW to 9pF – Changed typ value of CAINTOT to 20pF – Updated notes for EADNL,EAGAIN,TUE,EAINL,EAOFF – Changed fADCI to max 20MHz – Added fADC of 110MHz where ffpimax=110MHz – Added fADC of 80MHz where ffpimax=80MHz – Updated fADC min of 4MHz – Added sample time, tS, 2 to 255 tADCI – Added calibration time after reset, tCAL max 4352 cycles – Included footnote for TUE for 10-bit and 8-bit conversion – Removed IAIN7T (covered by RAIN7T ) – Removed IAREF, added QCONV – Updated notes for IOZ2 and IOZ3 – Updated typ value of 900Ohm for RAIN FADC parameters – Updated note for EFGRAD – Updated note for EFOFF – Added fFADC of 110MHz where ffpimax=110MHz – Added fFADC of 80MHz where ffpimax=80MHz – Added conversion time, tC – Added analog input voltage range,VAINF OSC XTAL parameters – Added fOSC – Changed max value of VIHX to VDDP+0.5V – Changed min value of VILX to -0.5V – Added typ values for internal load capacitors, CL0 to CL3, 2.5pF, 2.5pF, 4pF, 6.5pF – Added HYSAX Power Supply parameters – Updated IDDP, IDDM, IDDP_FP – Added IDD for fCPU=80MHz for max and realistic patterns – Updated PD values for max and real patterns, all external, fCPU=133MHz – Added text to of fCPU=133MHz to the note for the PD parameter. – Added PD for fCPU=80Mhz for max and realistic patterns for both all external mode and 5V only with ext.pass device mode Data Sheet 6-2 V1.2, 2014-06 TC1728 Revision History • • • • • • • • • • • • • • – Current consumption for LVDS pad pairs is updated for all LVDS pads in total – Deleted the redundant IDDP – Updated IDDP_FP, IDDP_PORST, IDD_PORST – Deleted RTHJA parameter Power Sequencing – Added Power Sequencing for 3.3V Supply Only section Power, Pad and Reset Timing parameters – Removed redundant note for tHDH, tHDS – Added text from note “TESTMODE/TRST” to the name of tPOH and tPOS, deleted note EVR Parameters – Added IPU_VDPG, VIH and VIL parameters in Pass Device Detector Table – Added EVR Parameter Table PLL SYSCLK parameters – Changed max value for fVCO – Added min value of 50us for tL – Included formula 1 and 2 – Removed note for peak-to-peak noise on pad supply voltage PLL ERAY parameters – Changed typ value to 250MHz for fPLLBASE – Added min value of 50us for tL – Removed note for peak-to-peak noise on pad supply voltage JTAG Interface parameters – Changed to ‘=’ signs in the notes for t8, t9 and t10 DAP parameters Peripheral Timings – Removed note for Peripheral Timings “Peripheral timing parameters are not subject to production test. They are verified by design/characterization.” MLI Timing – Added text for MLI parameters valid for CL=25pF MLI Receiver parameters – Changed fSYS to 110MHz in footnote 3 MLI Tranmitter parameters – Changed t13, TCLK rise time and t14, TCLK fall time to 0.3 x t10 MSC parameters – Added text for MSC parameters valid for CL=25pF – Added limits for different pad drive strength of t45 parameters – Changed min value of tt52 to 16.5ns ERAY parameters – Changed min value of t60 – Changed max value of t61-t62 – Changed min and max values of t63 Data Sheet 6-3 V1.2, 2014-06 TC1728 Revision History • • • – Changed max value of t64-t65 – Added dTxdly, dRxdly – Updated ERAY timing figure Flash32 parameters – Updated tPRD, tPRP – Changed min value of WSDF to 50ns x fLMB – Updated footnote 3 Package parameters – Added RTHJCT, RTHJCB, RTHJCL for LQFP144 Package outline – Added package outline for LQFP176 Changes from V0.5 to V0.6 • • • • • • • • • • • • • • • • • • • • • • • • • • • • Added max limit for VRST5 for 5.0V single supply Removed note above MLI Transmitter table Updated conditions for tFL and tRL for LVDS pad parameters Updated limits for RDSONW and RDSONM for Class A1 pads Updated limits for RDSONW and RDSONM and RDSON1+ for Class A1+ pads Updated limits for RDSONW and RDSONM and RDSON2 for Class A2 pads Updated limits for RDSONW and RDSONM for Class F pads Updated conditions for tRF and tFF for Class F pad parameters Added footnote 7 to ADC table Updated QCONVof ADC table Updated conditions to tL of PLL Sysclk Changed t19 of DAP from SR to CC Removed condition for V5 Added FADC input circuit Updated max limit for VAGND0 and min limit for VAREF0 tBWG and tBWR are added to ADC table Updated description of tCAL Added a placeholder for RAIN, RAIN7T, RAREF, tS, fADCI, EADNL, EAINL, EAGAIN, EAOFF, TUE at a separate ADC table for VDDM=3.3V Added a placeholder for tAWAF, tAWAS to both ADC tables for VDDM=5V and VDDM=3.3V Added a placeholder for tFWAF, tFWAS to FADC table for VDDM=5V, VDDM=3.3V Removed limits of gain=8 for EFGRAD Added VFAREFI and VFAGNDI parameters Updated limit of tSF2 to min 120ns Typo in Note for IV5 at 80MHz is corrected. Updated max limit of ΣIIN. Added IIN. Added Pin Reliability in Overload subchapter. Removed sentence “Exposure to conditions within the maximum ratings will not affect device reliability.” Replaced with the Pin Reliability in Overload subchapter. Data Sheet 6-4 V1.2, 2014-06 TC1728 Revision History • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Removed capacitance conditions for LVDS pad parameters, tRL, tFL , loads defined by interface (MSC) timing. Updated max limits of Flash parameters tPRD, tPRP Updated representation of IDDP Updated limits of IDD_PORST to max 110mA Updated limits of IDDP_PORST to max 6mA Updated limits of IDD for real pattern, fCPU=133MHz, to max 212mA Added new parameter IDDSUM Updated max limit of IDDM to 32mA Updated TC1728 IV5 for max and real patterns, fCPU=133MHz Updated PD for real pattern, fCPU=133MHz, all external supplies. Updated TC1728 PD for max and real patterns, fCPU=133MHz, 5V only with external pass device. Updated limit for RDSON2 of A2 pad, P_MOS Updated limits for RDSONM of F pad, P_MOS, N_MOS Removed VIH for Pass Device Detector Updated limits for VIL of Pass Device Detector Updated limits and test conditions for ∆VLOREG33 and ∆VLIREG33 Updated test condition for 5.0V single supply ∆VLOREG13 Updated limits and test condition for 5.0V single supply ∆VLIREG13 Corrected typ and max limits for COUT33 and COUT13 Added limit and test condition for 3.3V single supply ∆VLOREG13 and ∆VLIREG13 Application reset boot time limits are updated Added min limit for IOZS Added a new parameter VILSD Updated limits for tBP, STT Removed typical text from load of Peripheral Timing sections. Limits for EFGRAD with Gain=4 is changed to TBD Min limit for VDDM is changed to TBD Added EFREFI Added a placeholder for RFAIN, EFDNL, EFINL, EFGRAD, EFOFF at a separate ADC table for VDDM=3.3V Added max and typ limits for RRAIN for VDDM=3.3V Updated limits of PD for real pattern, fCPU=80MHz, to max 669mW Updated text for Note column of NE Corrected typo for Class D pads in PN-Junction Characteristics for positive/negative overload tables Updated limits of IDD for max pattern, fCPU=133MHz, to max 310mA Updated limits of IDD for max pattern, fCPU=80MHz, to max 248mA Updated limits of PD for max pattern, fCPU=133MHz, to max 902mA Updated limits of IDD for max pattern, fCPU=80MHz, to max 810mA Corrected typo for COUT13 Updated load jump current for COUT33 and COUT13 for fCPU=80MHz Changed min to typ value for CIN5 Data Sheet 6-5 V1.2, 2014-06 TC1728 Revision History Changes from V0.6 to V0.7 • Name of package is updated Changes from V0.7 to V0.8 • • • • • • • • • • • • • • • • • • • • • • • • Absolute maximum rating section for is updated for VDDP, VIN, VAIN, VAREF0, VAINF A footnote is added to tERD A note is added, updated pad supply levels in Pin Reliability in Overload section Updated min limit for t17 of MLI Added a footnote to IDDP Included text to power sequencing sections for setting of P0.4 and P0.5. Added limits for EFDNLfor Gain= 4, 8 Changed STT to tEVR, updated Power, Pad and Reset Timing figure Changed min limit of tL for PLL_Sysclk timing Removed IPU_VDPG for VDD5≥2.97V, VDD5£3.63V Updated limit and test condition for COUT33, COUT13 Updated limit for CIN5 Updated limit and test condition for ∆VLOREG33 Removed PSRR33, PSRR13 Updated test condition for ∆VLOREG13 Updated limit and test condition for ∆VLIREG13 Updated min limit for MSC t45, strong sharp setting, CMOS mode Added ∆VOUT33, ∆VOUT13 parameters Updated first sentence for Chapter 5.3 Added text for MLI and SSC parameters for validity of strong driver medium edge only Updated description for t52 and t53 Changed SSC parameters from CC to SR for t56, t57, t58, and t59 Changed min to max limit for EVR Supply ramp-up parameter Updated min limit for IPU_VDPG Changes from V0.8 to V1.0 • • • • • • • • • • • Added limits for EFGRAD for Gain= 4, 8 Added limits for EFREFI Updated VFAGNDI, VFAREFI, changed from SR to CC A footnote is added for VFAREFI Updated limit for CIN5 Added min limit for V5 Updated limits for fADCI, tBWG, tBWR , tAWAF, tAWAS, tFWAF, , tFWAS Updated limits for ADC table, VDDM=3.3V, fADCI, tBWG, tBWR , tAWAF, tAWAS, tFWAF, , tFWAS, RAIN7T, EADNL, EAGAIN, EAINL, , EAOFF, TUE , QCONV Corrected typo in test condition for RDSON Removed RDSONW parameter for class F pads Removed footnote 2 from ΣISC_D Data Sheet 6-6 V1.2, 2014-06 TC1728 Revision History • • • • • • • Added footnote 3 to VDDM Updated max limit for ADC parameter tS Added footnote 2 for t9 of JTAG parameter Changed t26, t27 from CC to SR Updated max limit for ADC parameter VAIN Added footnote 5 to t59 Added tPOR_APP parameter of Reset Timing parameters Changes from V1.0 to V1.1 • • • • • • • Updated description for tCAL Added a footnote to QCONV Added marking option SAK-TC1728F-192F133HR to Table 1,Summary of Features section Updated Figure 2, Figure 3-1, Figure 3-2 Added identification registers in Table 4 Updated fCPU, fFPI, fLMB, fPCP, fADC, fFADC, IDD, IDDSUM, IV5, PD Added footnote 8 to PD Changes from V1.1 to V1.2 • • • • • • • • • • change t48 from 100ns to 200ns in table 29 change t49 from 100ns to 200ns in table 29 extend KOVAN conditon from IOV≤ 0 mA; IOV≥ -1 mA to IOV≤ 0 mA; IOV≥ -2 mA clearify leakage definition for A1 and I pads for 150°C < TJ ≤ 160°C change VILS from 2.1V to 1.9V in table 25 change t56 from 1 / fFPI to 1 / fFPI + 1 in table 30 change RAIN from 4500 Ohm to 9000 Ohm in table 15 add the product options SAK-TC1728F-192F133HL shift the products SAK-TC1728F-192F133HR and SAK-TC1728N-192F80HR from step AB to AC Update max limit for pad class F parameter RDSONM Data Sheet 6-7 V1.2, 2014-06 w w w . i n f i n e o n . c o m Published by Infineon Technologies AG