MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS 20 LEAD PLLC CASE 775−02 ISSUE F 20 1 DATE 25 JUL 2008 SCALE 1:1 B 0.007 (0.180) Y BRK −N− M T L-M 0.007 (0.180) U M N S T L-M S G1 0.010 (0.250) S N S D −L− −M− Z W 20 D 1 X V S T L-M S N S VIEW D−D A 0.007 (0.180) M T L-M S N S R 0.007 (0.180) M T L-M S N S Z C H −T− VIEW S G1 0.010 (0.250) S T L-M SEATING PLANE STATUS: N S F 0.007 (0.180) M T L-M S N S S GENERIC MARKING DIAGRAM* DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.021 0.050 BSC 0.026 0.032 0.020 −−− 0.025 −−− 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 −−− 0.020 2_ 10 _ 0.310 0.330 0.040 −−− MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.53 1.27 BSC 0.66 0.81 0.51 −−− 0.64 −−− 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 −−− 0.50 2_ 10 _ 7.88 8.38 1.02 −−− 98ASB42594B ON SEMICONDUCTOR STANDARD NEW STANDARD: © Semiconductor Components Industries, LLC, 2002 October, DESCRIPTION: 2002 − Rev. 0 N VIEW S S NOTES: 1. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M, 1982. 2. DIMENSIONS IN INCHES. 3. DATUMS −L−, −M−, AND −N− DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 4. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM −T−, SEATING PLANE. 5. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 6. DIMENSIONS IN THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). DOCUMENT NUMBER: S K 0.004 (0.100) J T L-M M K1 E G 0.007 (0.180) 20 LEAD PLLC http://onsemi.com 1 1 20 XXXXXXXXX XXXXXXXXG AWLYYWW XXXXX A WL YY WW G = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ G”, may or may not be present. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “ CONTROLLED COPY” in red. Case Outline Number: PAGE 1 OFXXX 2 DOCUMENT NUMBER: 98ASB42594B PAGE 2 OF 2 ISSUE REVISION DATE E UPDATED MARKING DIAGRAM. REQ. BY S. FARRETTA 15 FEB 2005 F UPDATED MAX VALUES FOR DIMENSION F TO 0.021 IN AND 0.53 MM. CORRECTED GENERIC MARKING INFORMATION. REQ. BY L. JAMES. 25 JUL 2008 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. © Semiconductor Components Industries, LLC, 2008 July, 2008 − Rev. 02F Case Outline Number: 775