P20LD070-24 Step Down Driver for 0.7 A Power-LED ● ● ● ● ● ● ● Constant Current Output Dimmer function via analogue Control Dimmer function via PWM Control Remote control function 16 Pin DIL Package Efficiency up to 95 % MTBF > 5 MHours P20LD070-24 is a high efficiency step-down converter optimized to drive high current LEDs. The control algorithm allows highly efficient and precise LED current regulation. This driver operates in an dc supply voltage range between 7 V and 30 V and provides an externally adjustable output current of up to 0.7 A and output power up to 20 watts. A compact size allows designer to integrate this driver together with LED module. Specification at 25 °C, Vin nominal and rated output current Input Input voltage range Input filter Output Output voltage range at Vin 30 V Output current range at Vin - Vout > 1.5 V to 3 V Output power Typical output current accuracy, at Iout 1000 mA Output ripple and noise, bandwidth 20 MHz Temperature coefficient at Ta -40 to +85 °C Capacitive load Operating frequency range Efficiency, maximum at full load Short circuit protection PWM dimming & remote control Vdim input, remote ON level Vdim input, remote OFF level (shutdown) Vdim input, drive current (Vdim 1.25V) Quiescent supply current in shutdown mode at Vin 30V Recommended maximum operation frequency Minimum switch 'ON' time Minimum switch 'OFF' time Analog dimming control Vdim input control voltage range for 25 … 100 % output current range Vdim input control voltage range ON Vdim input control voltage range OFF Vdim input, drive current (Vdim 1.25V) Physical conditions Operating ambient temperature range Storage temperature range Operating Package temperature Thermal impedance, nature convection Humidity Reliability calculated MTBF (MIL-HDBK-217 F) Case material Potting material Pin material Weight Dimensions Soldering temperature 1.5 mm distance from body EMC Specifications in accordance with EMI radiated and conducted emissions EN55015 (CISPR22) EMS Immunity EN61547 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-6 IEC 61000-4-8 7…30 V Capacitor 2…28 V 700 mA 20 W, max. ±7 % 250 mVp-p, max. ±0.05 % / °C, max. 47 µF, max. 55 kHz…320 kHz 95 % Regulated at rated output current Open or 0.3 V … 1.25 V 0.15 V max. 1 mA, max. 25 µA, max. 1 kHz 200 ns 200 ns 0.3 V … 1.25 V 0.2 V … 0.3 V 0.15 V … 0.25 V 1 mA, max. -40 to +85 °C -40 to +125 °C 100 °C, max. 50 K/W 95 % rel H >5 Mhrs Non-conductive black plastic (UL94-V0) Silicon (UL94-V0 rated) 0.5 mm brass solder-coated 6.2 g PCB version, 11 g wire version 23.4 x 14 x 10.2 mm 260 °C for 10 sec Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Page 1 of 3 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] P20LD070-24 Step Down Driver for 0.7 A Power-LED Typical application circuits Notes: 1. Do not use the driver over 20 W output power! 2. Do not connect a reversed power source! 3. Do not connect the input side with output side! Page 2 of 3 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] P20LD070-24 Step Down Driver for 0.7 A Power-LED Pin connections Pin 1, 2 3 7, 8 9, 10 15, 16 - V supply Vdim - V output + V output + V supply Pin 1 black 2 white 8 blue 9 yellow 16 red Wire-Version - V supply Vdim - V output + V output + V supply Dimensions Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for use carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 7.12 f Page 3 of 3 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]