Common mode Noise Filters / Array Packaging Methods (Taping) ● Standard Quantity Part Number EXCX4C EXC14C EXC24C EXC34C EXC18C EXC28C Type Kind of Taping Pressed Carrier Taping Single Pitch (P1) 2 mm 2 mm Quantity 10,000 pcs./reel 10,000 pcs./reel 4 mm 5,000 pcs./reel Embossed Carrier Taping Array ● Embossed Carrier Taping EXCX4C Carrier Taping EXC14C P1 fD0 P2 t1 P0 Sprocket hole E P0 E Sprocket hole F B W A B F f D0 W ● Pressed Size (inch) 0202 0302 0504 0805 0603 0804 A T ● Embossed P1 t2 Compartment Chip component Tape running direction Chip component ● Taping Carrier Taping P2 Compartment Tape running direction Reel EXC18C, 24C, 28C, 34C T Compartment B F A P1 t2 Chip component ● Pressed fC P2 fD E P0 fA W Tape running direction Carrier Taping (mm) Part Number A B W F E P1 EXCX4C 0.60±0.10 0.80±0.10 8.0±0.2 3.50±0.05 1.75±0.10 2.0±0.1 ● Embossed Part Number EXC14C EXC18C EXC24C EXC28C EXC34C ● Taping fB fD0 W Sprocket hole E t1 P2 2.0±0.1 P0 4.0±0.1 fD0 +0.1 1.5 0 T 0.35 typ. Carrier Taping (mm) A B W F E P1 P2 P0 0.75±0.10 0.95±0.10 8.0±0.2 3.50±0.05 1.75±0.10 2.0±0.1 2.0±0.1 4.0±0.1 1.00±0.10 1.80±0.10 1.45±0.15 1.20±0.15 8.0±0.2 3.5±0.1 1.75±0.10 4.0±0.1 2.0±0.1 4.0±0.1 2.25±0.15 1.50±0.20 2.30±0.20 fD0 +0.1 1.5 0 +0.1 0 1.5 t1 t2 0.25±0.05 0.85±0.15 0.80±0.05 0.25±0.05 0.90±0.15 Reel Standard Reel Dimensions Part Number EXCX4C EXC14C EXC18C EXC24C EXC28C EXC34C (mm) fA fB 180.0±3.0 60.0±1.0 fC 13.0±0.2 13.0±0.5 fD E W 21.0±0.8 2.0±0.5 9.0±0.3 T 11.4±1.0 11.4±1.5 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 05 Oct. 2015 Common mode Noise Filters / Array Recommended Land Pattern Design ● Single B E F E D Part Number Dimensions (mm) A 0.80 to 0.90 0.80 to EXC14C 1.00 1.60 to EXC24C 2.00 C D A EXCX4C EXC34C ● Array 2.60 B C D E 0.60 to 0.20 to 0.30 0.75 0.30 0.25 to 0.80 0.30 0.35 0.45 to 0.95 0.70 0.65 1.20 1.10 F 0.20 to 0.20 to 0.25 0.25 0.75 0.30 0.20 0.35 0.25 0.40 0.40 B E Part Number D A C D F Dimensions (mm) A B C D E F EXC18C 1.4 1.4 0.4 0.5 0.2 0.4 EXC28C 1.4 1.75 0.4 0.5 0.25 0.5 Recommended Soldering Conditions Recommendations and precautions are described below ● Recommended soldering conditions for reflow · Reflow soldering shall be performed a maximum of two times. · Please contact us for additional information when used in conditions other than those specified. · Please measure the temperature of the terminals and study every kind of solder and printed circuit board for solderability before actual use. Temperature Peak Preheating Heating For soldering (Example : Sn-37Pb) Temperature Preheating 140 °C to 160 °C Main heating Above 200 °C Peak 235 ± 10 °C Time 60 s to 120 s 30 s to 40 s max. 10 s For lead-free soldering (Example : Sn/3Ag/0.5Cu) Temperature Time Preheating 150 °C to 170 °C 60 s to 120 s Main heating Above 230 °C 30 s to 40 s Peak max. 260 °C max. 10 s Time ● Flow soldering · We do not recommend flow soldering, because flow soldering may cause bridges between the electrodes. <Repair with hand soldering> ● Preheat with a blast of hot air or similar method. Use a soldering iron with a tip temperature of 350 °C or less. Solder each electrode for 3 seconds or less. ● Never touch this product with the tip of a soldering iron. Safety Precations The following are precautions for individual products. Please also refer to the common precautions for EMC Components in this catalog. 1. Use rosin-based flux or halogen-free flux. 2. For cleaning, use an alcohol-based cleaning agent. Before using any other type, consult with our sales person in advance. 3. Do not apply shock to Common mode Noise Filters (hereafter called the filters) or pinch them with a hard tool (e.g. pliers and tweezers). Otherwise, their bodies may be chipped, affecting their performance. Excessive mechanical stress may damage the filters. Handle with care. 4. Store the filters in a location with a temperature ranging from –5 °C to +40 °C and a relative humidity of 40 % to 60 % , where there are no rapid changes in temperature or humidity. 5. Use the filters within a year after the date of the outgoing inspection indicated on the packages. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 05 Oct. 2015