Common mode Noise Filters / Array

Common mode Noise Filters / Array
■ Packaging Methods (Taping)
● Standard Quantity
Part Number
Size (inch)
Kind of Taping
Pitch (P1)
Quantity
EXCX4C◻◻◻◻U
0202
Punched Carrier Taping
2 mm
10000 pcs./reel
2 mm
10000 pcs./reel
4 mm
5000 pcs./reel
EXC14C□□□□U
0302
EXC24C□□□□U
0504
EXC18C□□□□U
0603
EXC28C□□□□U
0804
EXC34C□□□□U
0805
Embossed Carrier Taping
● Punched Carrier Taping
(mm)
Sprocket hole
P1
fD0
P2
B
W
F
E
P0
A
T
Type
EXCX4C
A
Compartment
Chip component
B
W
F
E
Tape running direction
P1
0.60±0.10 0.80±0.10 8.0±0.2 3.50±0.05 1.75±0.10
P2
2.0±0.1
fD0
P0
2.0±0.1
4.0±0.1
1.5
+0.1
0
T
0.35 typ.
(mm)
● Embossed Carrier Taping
t1
P0
F
A
B
f D0
W
E
Sprocket hole
P1
t2
Chip component
Type
EXC14C
A
B
W
F
P2
Compartment
E
Tape running
direction
P1
0.75±0.10 0.95±0.10 8.0±0.2 3.50±0.05 1.75±0.10 2.0±0.1
P2
2.0±0.1
P0
4.0±0.1
fD0
1.5
+0.1
0
t1
0.25±0.05 0.85±0.15
(mm)
● Embossed Carrier Taping
Compartment
fD0
E
Sprocket hole
B
F
A
P1
t2
P2
Chip component
EXC18C
EXC24C
EXC28C
EXC34C
A
B
W
F
W
t1
形 式
P0
Tape running direction
E
P1
P2
P0
fD0
t1
1.00±0.10 1.80±0.10
1.20±0.15
1.45±0.15
2.25±0.15
t2
t2
0.80±0.05
8.0±0.2 3.5±0.1 1.75±0.10 4.0±0.1
2.0±0.1
4.0±0.1
1.5+0.1
0
0.25±0.05
0.90±0.15
1.50±0.20 2.30±0.20
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03 Nov. 2012
25
Common mode Noise Filters / Array
● Taping Reel
(mm)
Standard Reel Dimensions
0A
Type
T
EXCX4C
EXC14C
EXC18C
EXC24C
EXC28C
EXC34C
fB
fC
fD
fA
EXCX4C
EXC14C
EXC18C
EXC24C
EXC28C
EXC34C
W
0C
0D
13.0±0.2
180.0±3.0 60.0±1.0
Type
E
0B
E
13.0±0.5
W
21.0±0.8
T
11.4±1.0
2.0±0.5
9.0±0.3
11.4±1.5
■ Recommended Land Pattern Design
● EXCX4, EXC14, EXC24, EXC34
B
E
F
D
Type
A
B
C
D
E
F
C
0.80 to 0.60 to 0.20 to
0.20 to 0.20 to
EXCX4C
0.30
0.90
0.75
0.30
0.25
0.25
0.80 to
0.25 to
EXC14C
0.80 0.30
0.30 0.20
1.00
0.35
1.60 to
0.45 to
0.95 0.70
0.35 0.25
EXC24C
2.00
0.65
D
A
Dimensions (mm)
E
EXC34C
2.60
1.20
1.10
0.75
0.40
0.40
● EXC18C, EXC28C
B
E
Type
D
A
C
D
F
Dimensions (mm)
A
B
C
D
E
F
EXC18C
1.4
1.4
0.4
0.5
0.2
0.4
EXC28C
1.4
1.75
0.4
0.5
0.25
0.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03 Nov. 2012
26
Common mode Noise Filters / Array
■ Recommended Soldering Conditions
Recommendations and precautions are described below
● Recommended soldering conditions for reflow
· Reflow soldering shall be performed a maximum of
two times.
· Please contact us for additional information when
used in conditions other than those specified.
· Please measure the temperature of the terminals
and study every kind of solder and printed circuit
board for solderability before actual use.
For soldering (Example : Sn-37Pb)
Preheating
Main heating
Peak
Temperature
Peak
Temperature
140 °C to 160 °C
Above 200 °C
235 ± 10 °C
Time
60 s to 120 s
30 s to 40 s
max. 10 s
For lead-free soldering (Example : Sn/3Ag/0.5Cu)
Temperature
Time
Preheating
150 °C to 170 °C
60 s to 120 s
Main heating
Above 230 °C
30 s to 40 s
Peak
max. 260 °C
max. 10 s
Preheating
Heating
Time
● Flow soldering
· We do not recommend flow soldering , because flow soldering may cause bridges between the electrodes.
<Repair with hand soldering>
● Preheat with a blast of hot air or similar method. Use a soldering iron with a tip temperature of 350 °C or less. Solder
each electrode for 3 seconds or less.
● Never touch this product with the tip of a soldering iron.
Safety Precations
The following are precautions for individual products. Please also refer to the common precautions for Noise Suppression
Device shown on this catalog.
1. Use rosin-based flux or halogen-free flux.
2. For cleaning, use an alcohol-based cleaning agent. Before using any other type, consult with our sales person
in advance.
3. Do not apply shock to Common mode Noise Filters (hereafter called the filters) or pinch them with a hard tool
(e.g. pliers and tweezers). Otherwise, their bodies may be chipped, affecting their performance. Excessive mechanical stress may damage the filters. Handle with care.
4. Store the filters in a location with a temperature ranging from –5 °C to +40 °C and a relative humidity of 40 % to 60 %,
where there are no rapid changes in temperature or humidity.
5. Use the filters within half a year after the date of the outgoing inspection indicated on the packages.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03 Nov. 2012
27