Pan-Way ® LD2P10 Surface Raceway System S P E C I F I C AT I O N S H E E T specifications Type LD2P10 non-metallic two channel, one-piece tamper resistant latch design, adhesive backed, hinged cover surface raceway shall be used to route, protect and conceal low voltage data, voice, fiber optic and power cabling. The raceway shall be listed as suitable for use in applications having up to 600V between conductors by Underwriters Laboratories, Inc. per Standard 5A and by Canadian Standards Associations per C22.2 No. 62.1-03 when installed per instructions. The raceway includes a full complement of bend radius control (BRC) fittings consisting of, but not limited to: elbows, (internal and external), couplings for joining raceway sections, blank end fittings for closing open ends of the raceway, entrance end fittings, reducer fittings, tee fittings, and an optional raceway installation tool. The BRC fittings shall incorporate a minimum of 1" bend radius as recommended for Category 6 UTP and fiber optic cabling in TIA/EIA 569-B. This non-metallic surface raceway shall be manufactured in two standard lengths from impact resistant material with a flammability rating of UL94V-0. The non-metallic raceway finish shall be pure color, resist scratches and dents and not peel or corrode. The raceway shall be available in four standard colors and shall be optimized for use with Panduit® Pan-Net ® Network Cabling Systems. technical information Rigid PVC Flammability: UL94V-0; FT4 Voltage rating: UL-5A 600VAC; CSA C22.2 No. 62.1-03 600V Approvals: UL Listed 95425 (raceway); UL Listed E116129 (fittings) NEC: Article 388 Color: Off White (IW), Electrical Ivory (EI), International Gray (IG), White (WH) CSI spec form: LP-CSISPEC-LD2P10-1 key features and benefits Multi-channel system Allows end user to purchase one raceway to route both data and power cabling Available 1" bend radius control fittings Meets TIA/EIA standard and many warranty requirements One-piece hinged design Cables can be laid into the raceway, which prevents damage to cables during installation Adhesive backing for temporary mounting Installations are easier and faster, reducing the total installed cost Highly tamper resistant Provides maximum security for communication cabling and maximum safety for power cabling Non-metallic construction Lightweight, which reduces installer fatigue and reduces labor required to install the raceway; solid color throughout will not chip, peel, rust or corrode; easy to cut with standard saws and saw blades, which reduces the need for special cutting devices Available in four colors Matches a wide variety of colors for various applications applications w w w. p a n d u it.c o m Raceway:LD2P10IW**-A LD2P10 Raceway Fittings Coupler fitting: CFX10IW-X Inside corner fitting: ICFX10IW-X Outside corner fitting: OCFX10IW-X Right angle fitting: RAFX10IW-X Tee fitting: TFXD10IW-X End cap fitting: ECFX10IW-X Entrance end fitting: EEFXIW Raceway installation tool: LDW10-V **Insert raceway length of 8' or 10'. All parts listed in Off White (IW) color. To order other colors substitute Electrical Ivory (EI), International Gray (IG), and White (WH). Material: Pan-Way ® LD2P10 Profile Raceway is a one-piece multi-channel channel raceway which provides solutions for routing both Pan-Way ® LD2P10 Raceway power and data cabling along perimeter walls. LD2P10 profile raceway is available with multi-channel fittings. Pan-Way ® LD2P10 Surface Raceway System wire fill Electrical Cables Data Grade Cables Coax Cables 14 AWG 12 AWG 10 AWG 24 AWG 24 AWG 24 AWG 24 AWG THHN/THWN/T90 Cat 5e — Plenum Cat 5e — Riser Cat 6 and Cat 6A (SD) Cat. 6A DIA = 0.193 DIA = 0.225 DIA = 0.240 FILL FILL FILL 0.111 0.130 0.164 FILL Raceway Type and Configuration Fill Area (in²) MAX LD2P10 — Left Channel 0.43 14 11 LD2P10 — Right Channel 0.50 ** ** MAX MAX Fiber Optic Cable RG6 RG59/u 2 Strand DIA = 0.300 DIA = 0.275 DIA = 0.242 DIA = 0.175 FILL FILL FILL FILL SPEC MAX SPEC MAX SPEC MAX SPEC MAX SPEC MAX SPEC MAX SPEC MAX (40%) (60%) (40%) (60%) (40%) (60%) (40%) (60%) (40%) (60%) (40%) (60%) (40%) (60%) 8 ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** 6 10 5 7 4 6 2 4 3 5 4 6 8 12 (UL Temp Rise Test) LD2P raceway A= A= 0.43in2 0.50in2 0.86" LD2P10 fittings CFX ICFX OCFX TFXD ECFX EEFX RAFX LDW10-V WORLDWIDE SUBSIDIARIES AND SALES OFFICES PANDUIT CANADA Markham, Ontario [email protected] Phone: 800.777.3300 PANDUIT EUROPE LTD. London, UK [email protected] Phone: 44.20.8601.7200 PANDUIT SINGAPORE PTE. LTD. Republic of Singapore [email protected] Phone: 65.6305.7575 PANDUIT JAPAN Tokyo, Japan [email protected] Phone: 81.3.6863.6000 PANDUIT LATIN AMERICA Guadalajara, Mexico [email protected] Phone: 52.33.3777.6000 PANDUIT AUSTRALIA PTY. LTD. Victoria, Australia [email protected] Phone: 61.3.9794.9020 For a copy of Panduit product warranties, log on to www.panduit.com/warranty For more information Visit us at www.panduit.com Contact Customer Service by email: [email protected] or by phone: 800.777.3300 ©2014 Panduit Corp. ALL RIGHTS RESERVED. SRSP29--WW-ENG Replaces WW-SRSP07 11/2014