Pan-Way® LDS Surface Raceway System SRSP25--WW-ENG

Pan-Way® LDS Surface Raceway System
S P E C I F I C AT I O N S H E E T
specifications
LDS non metallic surface raceway will be a one piece, solid
raceway used to route, protect, and conceal data network, voice
or power cabling. The raceway shall be listed as suitable for use
in applications having up to 600 volts between conductors by
Underwriters Laboratories, Inc. per standard 5A when screw
secured with mounting straps and per installation instructions.
The raceway shall be manufactured from impact resistant
material with flammability rating of UL94V-0. A full complement
of power, 1" bend radius control, and standard snap on fittings
must be available. All fittings and boxes shall be tamper resistant
to prevent unauthorized access to cables. LDS raceway finish
shall be pure color and will resist scratches and dents and will
not peel or corrode.
technical information
LDS Raceway
3 series:
5 series:
LDS3IW10-A
LDS5IW10-A
Mounting Straps for
Power Applications
3 series:
5 series:
LMD3IW-Q
LMD5IW-Q
LDS Raceway
Power-Rated Fittings
Coupler fitting:
CFX*IW-X
Right angle
fitting:
RAFX*IW-X
Inside corner
fitting:
ICFX*IW-X
OCFC*IW-X
TFX*IW-X
Material:
Rigid PVC
Flammability:
UL94V-0
Outside corner
fitting:
Voltage rating:
UL 600V / CSA 600V
Tee fitting:
Colors:
International White (IW), Electric Ivory (EI),
Four way cross
fitting (LDS5 only): CRFX5IW-X
International Gray (IG), or White (WH)
CSI spec form:
LP-CSISPEC-LDS-1
key features and benefits
Tamper resistant design
Solid one-piece design provides increased tamper
resistance over hinged raceway
Available 1" bend radius
control fittings
Cables in the raceway will satisfy the minimum 1" bend
radius requirement, preventing the potential degradation
of cable performance of high performance cabling systems;
meets TIA/EIA standards and many warranty requirements;
contact customer service for specific part numbers
Only non-metallic
bendable raceway
Can route around and over obstructions in low
voltage applications
Standard and power
rated fittings
Most economical fittings for low voltage or power
applications; rated to 600V and tamper resistant; contact
customer service for specific low-voltage fitting part numbers
Non-metallic construction
Lightweight reducing installer fatigue and labor required to
install the raceway; solid color throughout will not chip, peel,
rust or corrode; easy to cut with standard saws and saw
blades reducing the need for special cutting devices
Adhesive backing
Installations are easier and faster reducing the total
installed cost
Available in four
standard colors
Matches a wide variety of colors for various applications
applications
Pan-Way ® LDS Profile Raceway is a single
channel non-hinged raceway which provides
solutions for routing of power or low voltage
data and fiber optic cabling along perimeter
walls. LDS Raceway is the only non-metallic
w w w. pa n d u it.c o m
raceway that is bendable in low voltage
applications to route around and over
obstructions, has a tamper resistant design
and is available with standard, bend radius
control and power rated fittings.
End cap fitting:
ECFX*IW-X
Drop
ceiling/entrance
end fitting:
DCEFXIW-X
Right
angle/entrance
end fitting:
RAEFXIW-X
Reducer fitting
from size 5 to 3:
RFX53IW-X
Reducer fitting
from size 10 to 3: RFX103IW-X
Reducer fitting
from size 10 to 5: RFX105IW-X
For standard colors other than
IW (International White), replace
IW in part number with EI (Electric Ivory),
IG (International Gray), or WH (White).
For LDS3 fittings, replace * with 3.
For LDS5 fittings, replace * with 5.
Pan-Way ® LDS Surface Raceway System
Wire Fill
Electrical Cables
14
AWG
12
AWG
Data Grade Cables
10
AWG
THHN/THWN/T90
0.111
0.13
0.164
Fill
Area
(in²)
LDS3
0.21
9
6
LDS5
0.38
10
8
MAX
MAX
MAX
Fiber Optic Cable
24
AWG
24
AWG
24
AWG
Cat. 5e – Plenum
Cat. 5e – Plenum
Cat. 6 and
Cat. 6A (SD)
Cat. 6A
RG6
RG59/u
2 Strand
DIA = 0.193
DIA = 0.225
DIA = 0.240
DIA = 0.300
DIA = 0.275
DIA = 0.242
DIA = 0.175
Fill
Fill
Fill
Fill
Fill
Fill
Fill
Raceway
Type &
Configuration
Coax Cables
24
AWG
Fill
SPEC
MAX
SPEC
MAX
SPEC
MAX
SPEC
MAX
SPEC
MAX
SPEC
MAX
(40%)
(60%)
(40%)
(60%)
(40%)
(60%)
(40%)
(60%)
(40%)
(60%)
(40%)
(60%)
4
2
4
2
3
1
2
1
1
1
2
3
5
5
5
7
3
5
3
5
2
3
2
3
6
9
(UL Temp Rise Test)
0.55
0.41
0.77
LDS3
Internal Area = 0.21 Sq. In.
LDS5
Internal Area = 0.38 Sq. In.
Fittings
CFX
RAFX
ICFX
OCFC
TFX
CRFX
ECFX
DCEFX
RAEFX
RFX
WORLDWIDE SUBSIDIARIES AND SALES OFFICES
PANDUIT CANADA
Markham, Ontario
[email protected]
Phone: 800.777.3300
PANDUIT EUROPE LTD.
London, UK
[email protected]
Phone: 44.20.8601.7200
PANDUIT SINGAPORE PTE. LTD.
Republic of Singapore
[email protected]
Phone: 65.6305.7575
PANDUIT JAPAN
Tokyo, Japan
[email protected]
Phone: 81.3.6863.6000
PANDUIT LATIN AMERICA
Guadalajara, Mexico
[email protected]
Phone: 52.33.3777.6000
PANDUIT AUSTRALIA PTY. LTD.
Victoria, Australia
[email protected]
Phone: 61.3.9794.9020
For a copy of Panduit product warranties, log on to www.panduit.com/warranty
For more information
Visit us at www.panduit.com
Contact Customer Service by email: [email protected]
or by phone: 800.777.3300
©2014 Panduit Corp.
ALL RIGHTS RESERVED.
SRSP25--WW-ENG
1/2014