Description Function and application The TOUCH DIM LS/PD LI sensor regulates the brightness at the workplace and in office areas to increase the working comfort and to save energy. TOUCH DIM LS/PD LI The sensor can be installed in luminaires (e.g. floor standing luminaires) or in false ceilings. Function The sensor measures the brightness in the area to be regulated and keeps this to an adjustable set value by introducing artificial light according to the amount of daylight available. A B The sensor also detects the movements of people. C As daylight increases the artificial light is reduced . The sensor no longer detects any motions, it switches the luminaires off. Construction The sensor is made up of the following components: • Light sensor (A) • Motion sensor (B) • Housing (C) • Connections (D) for signal line, zero line and phase D Light and motion sensor Fitting instructions Installation Safety instructions The sensor must only be installed and put into operation by a qualified electrician. The applicable safety regulations and accident prevention regulations must be observed. WARNING! Exposed, live cables or damaged housing. Danger of electric shock! • Only work on the sensor when it is deenergized. • Disconnect the sensor or luminaire from the power supply if the housing or plastic lens is damaged. CAUTION! Destruction of the sensor and other devices through incorrect mounting! • Only use electronic OSRAM ballast coils of the type QUICKTRONIC INTELLIGENT DALI (QTi DALI…DIM), HALOTRONIC INTELLIGENT DALI (HTi DALI…DIM) or OPTOTRONIC INTELLIGENT DALI (OT…DIM). • Do not operate any other other control units on the control line. • Do not exceed the maximum number of ballast coils and maximum overall cable length between the operating button, sensor and ballast coil. • Do not connect control line with external voltage. • Only supply sensor with an AC operating voltage, especially in networks with UPS systems. L N PE Connecting the sensor F ~ ~ E DA L N S 1 EVG QTi DALI 2 3 DA 4 ~ ~ 1 DA DA EVG QTi DALI 2 E Operating pushbutton: Same phase as sensor. F Electronic ballast coil (EVG): Connect max. 4 ballast coils. G Signal line: Max. 10 m. H Sensor: Cable connection via 3-wires permitted for mains voltage. Do not switch the sensors in parallel. 3 4 H Touch DIM Sensor G Continued on the back page! Fitting (cont.) Selecting the installation location I Surveillance cone: entire workplace; not on window surfaces K Avoid direct light irradiation L Avoid drafts (e.g. from ventilators or fans) M Place centrally. Optimum installation location Possible installation location 80° – 100° 80° – 100° I K L M Appendix Technical data Operating voltage 220-240 V / 50-60 Hz (no DC operation) Connections L, N, S (signal) Interface Osram-specific, maximum 4 QTi DALI coil ballast or 4 HTi transformers or 4 OTi LED dimmers can be connected Maximum overall length of the signal line 10 m Power consumption approx. 0.5 W Operating temperature 0 °C ... +50 °C Adjustable light value approx. 0-300 lx measured on the sensor (corresponds to approx. 10-1200 lx on the work surface) Motion detection area conical, approx. 80° ... 100° aperture angle Pollution severity 2 (dry, not conductive to IEC 664) Dimensions 63 x 29 x 21 mm (L x W x H) Protection class II Protection type IP 20 VII 2008 TouchDIM-LSPD-LI_ma0807en_we1.02.indd OSRAM GmbH Kunden Service Center Customer-Service-Center (CSC) Steinerne Furt 62 86167 Augsburg Germany Tel : +49 (0) 1803 677 - 200 (kostenpflichtig / charges apply) Fax.: +49 (0) 1803 677 - 202 The EMC requirements to EN 61547 are fulfilled. www.osram.com www.osram.de 40083210230250 4008321023025 Conformity with the relevant EU directives is confirmed by the CE symbol.