NEC EXPRESS5800/R110d-1E Configuration Guide Introduction This document contains product and configuration information that will enable you to configure your system. The guide will ensure fast and proper configuration of your NEC Express5800 server. May 2012 Revision 2.3 NEC Corporation CONFIGURATION GUIDE – NEC Express5800/R110d-1E Contents TECHNICAL SPECIFICATION ........................................................................................ 3 Key Features .......................................................................................................................................... 3 Specification .......................................................................................................................................... 3 EXTERNAL VIEWS ......................................................................................................... 7 Front and Rear Views ........................................................................................................................... 7 Dimensions (mm) .................................................................................................................................. 8 CONFIGURATION DIAGRAM ......................................................................................... 9 SERVER CONFIGURATION ......................................................................................... 10 1 2 3 4 5 6 7 8 Base Models ................................................................................................................................. 10 Processor ..................................................................................................................................... 10 Memory ......................................................................................................................................... 10 Internal Hard Disk Drives ............................................................................................................ 11 4.1 RAID Configuration .............................................................................................................. 11 4.2 Internal Drive Configuration ................................................................................................. 13 Optical Drive ................................................................................................................................. 25 Internal Flash Memory ................................................................................................................. 25 PCI Card ........................................................................................................................................ 26 7.1 LAN Controller ..................................................................................................................... 26 7.2 External RAID Controller ..................................................................................................... 26 7.3 Fibre Channel/SAS/SCSI Controller .................................................................................... 27 7.4 Serial Port Adapter .............................................................................................................. 27 Add-on Components ................................................................................................................... 27 8.1 17-inch LCD Console Drawer .............................................................................................. 27 8.2 KVM Switch ......................................................................................................................... 28 8.3 Server Management License............................................................................................... 28 8.4 Flash FDD............................................................................................................................ 28 8.5 Front Bezel .......................................................................................................................... 28 REFERENCES............................................................................................................... 29 Note for Ordering ................................................................................................................................ 29 Server Management ............................................................................................................................ 29 OS Support Matrix for PCI Cards ...................................................................................................... 30 Supporting PCI cards and Installable Slots ..................................................................................... 31 Copyright Notice and Liability Disclaimer ........................................................................................ 32 REVISION HISTORY ..................................................................................................... 33 NEC Corporation Revision 2.3, May 2012 2 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Technical Specification Key Features High performance with the latest Intel® Xeon® processor E3-1200 series Up to 32 GB of high speed DDR3-1333 memory High energy efficiency with intelligent fan control, power capping feature and 80 PLUS® Gold power supply Full manageability by integrated EXPRESSSCOPE Engine 3 Specification 3.5-inch Drive Model Model R110d-1E Part Number N8100-1744F Processor Type Intel® Pentium® processor G630 Intel® Xeon® processor E3-1220 Intel® Xeon® processor E3-1270 Clock speed 2.70 GHz 3.10 GHz 3.40 GHz Number of Processor 1 Cache 3 MB 8 MB 8 MB Cores and Threads 2C / 2T 4C / 4T 4C / 8T Chipset Memory Internal Storage Intel® C204 Chipset Type DDR3-1333 ECC Unbuffered DIMM Standard Capacity 0 GB Maximum Capacity 32 GB (4 x 8 GB) Standard Capacity 0 GB Maximum Capacity SATA : 12 TB (4 x 3 TB) Disk Controller SATA : 3 Gb/s (Integrated) RAID SATA : Hot Plug Supported Optical Disk Drive Optional Optical Drive Bays [free] Disk Drive Bays [free] 1 [1] 12 RAID 0/1/10 (Standard), RAID 5/6 (Optional) 4 [4] Expansion Slots [free] Total: 2 slots available 1 [1] x PCIe 2.0 x8 (x16 connector) 1 [1] x PCIe 2.0 x8 (x8 connector) Video Controller (VRAM) Integrated in Server Management Controller (32MB) Interfaces 1 x VGA (15-pin mini D-sub,1x rear) 1 x Serial (9-pin mini D-sub, RS232-C, Serial A, 1 x rear) 8x USB2.0 (2 x front, 4 x rear, 2 x internal) 2x 1000BASE-T LAN connector (1000BASE-T / 100BASE-TX / 10BASE-T, RJ-45, 2 x rear) 1 x Management LAN connector (100BASE-TX / 10BASE-T, RJ-45, 1 x rear) Server Management EXPRESSSCOPE Engine 3 System Fan Standard Power Supply 1 x 400 Watt 80 PLUS® Gold certified non-Hot plug PSU 100-240 VAC ± 10% 50 / 60 Hz ± 3 Hz NEC Corporation Revision 2.3, May 2012 3 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Model Power Consumption R110d-1E (Max. Config, Idling) 108 VA / 102 Watt 109 VA / 105 Watt 109 VA / 106 Watt (Max. Config, Operating) Minimum Config. 161 VA / 159 Watt 223 VA / 222 Watt 281 VA / 270 Watt Acoustical Noise (Sound Pressure Maximum Config. 3 Level) Dimensions (W x D x H ) 42.3 dB 39.3 dB 39.3 dB 43.1 dB 48.8 dB 48.8 dB Weight (Minimum / Maximum) 10 kg / 18 kg, 22.05 lbs. / 39.68 lbs. Temperature, Relative Humidity (non-condensing) Operating: 10° to 35° C / 50° to 95° F, 20 to 80% Non-Operating: -10° to 55° C / 14° to 131° F, 20 to 80% Regulatory and Safety FCC, CE, BSMI, CCC, UL, CB, RoHS, WEEE Pre-installed Operating System - Operating Systems Microsoft® Windows Server® 2003 R2, Standard Edition SP2 or later Microsoft® Windows Server® 2003 R2, Enterprise Edition SP2 or later Microsoft® Windows Server® 2003 R2, Standard x64 Edition SP2 or later Microsoft® Windows Server® 2003 R2, Enterprise x64 Edition SP2 or later Microsoft® Windows Server® 2008 Standard Microsoft® Windows Server® 2008 Standard (x64) Microsoft® Windows Server® 2008 Enterprise Microsoft® Windows Server® 2008 Enterprise (x64) Microsoft® Windows Server® 2008 R2 Standard Microsoft® Windows Server® 2008 R2 Enterprise 4 Red Hat Enterprise Linux 5.6 or later 4 Red Hat Enterprise Linux 5.6 or later (EM64T) 4 Red Hat Enterprise Linux 6.0 or later (x86) 4 Red Hat Enterprise Linux 6.0 or later (x86_64) 1 2 3 4 444.0 x 615.2 x 43.6 mm / 17.5 x 24.2 x 1.7 in (1U) On-board SATA Controller does not support RAID 10 configured with 2TB and 3TB HDDs. The on-board SATA RAID controller is not supported on Linux operating systems. Noise emission was measured in accordance with ISO 7779. The actual value may vary by the operating environment. For Linux support, contact our sales representative or go to the NEC website at: http://www.nec.com/global/prod/express/linux/index.html NEC Corporation Revision 2.3, May 2012 4 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 2.5-inch Drive Model Model R110d-1E Part Number Processor N8100-1745F Type Intel® Pentium® processor G630 Intel® Xeon® processor E3-1220 Intel® Xeon® processor E3-1270 Clock Speed 2.70 GHz 3.10 GHz 3.40 GHz Number of Processor 1/1 Cache 3 MB 8 MB 8 MB Cores and Threads 2C / 2T 4C / 4T 4C / 8T Chipset Memory Internal Storage Intel® C204 Chipset Type DDR3-1333 ECC Unbuffered DIMM Standard Capacity 0 GB Maximum Capacity 32 GB (4 x 8 GB) Standard Capacity 0 GB Maximum Capacity SAS : 5.4 TB (6 x 900 GB) SATA : 6 TB (6 x 1 TB) SSD : 600 GB (6 x 100 GB) Disk Controller SATA : 3 Gb/s (Integrated) SAS : 6 Gb/s (Optional) RAID SATA : RAID 0/1/10 (Standard), RAID 5/6 (Optional) SAS : RAID 0/1/10/5/6 (Optional) Hot Plug Supported Optical Disk Drive Optional Optical Drive Bays [free] Disk Drive Bays [free] 1 [1] 1 6 [6] Expansion Slots [free] Total: 2 slots available 1 [1] x PCIe 2.0 x8 (x16 connector) 1 [1] x PCIe 2.0 x8 (x8 connector) Video Controller (VRAM) Integrated in Server Management Controller (32MB) Interfaces 1 x VGA (15-pin mini D-sub,1x rear) 1 x Serial (9-pin mini D-sub, RS232-C, Serial A, 1 x rear) 8x USB2.0 (2 x front, 4 x rear, 2 x internal) 2x 1000BASE-T LAN connector (1000BASE-T / 100BASE-TX / 10BASE-T, RJ-45, 2 x rear) 1 x Management LAN connector (100BASE-TX / 10BASE-T, RJ-45, 1 x rear) Server Management EXPRESSSCOPE Engine 3 System Fan Standard Power Supply 1 x 400 Watt 80 PLUS® Gold certified non-Hot plug PSU 100-240 VAC ± 10% 50 / 60 Hz ± 3 Hz Power Consumption (Max. Config, Idling) 107 VA / 102 Watt 123 VA / 119 Watt 125 VA / 120 Watt (Max. Config, Operating) Minimum Config. 149 VA / 146 Watt 236 VA / 233 Watt 261 VA / 260 Watt Acoustical Noise (Sound Pressure Maximum Config. 2 Level) Dimensions (W x D x H ) 42.3 dB 39.3 dB 39.3 dB 43.1 dB 48.8 dB 48.8 dB Weight (Minimum / Maximum) 10 kg / 18 kg, 22.05 lbs. / 39.68 lbs. NEC Corporation 444.0 x 615.2 x 43.6 mm / 17.5 x 24.2 x 1.7 in (1U) Revision 2.3, May 2012 5 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Model R110d-1E Temperature, Relative Humidity (non-condensing) Operating: 10° to 35° C / 50° to 95° F, 20 to 80% Non-Operating: -10° to 55° C / 14° to 131° F, 20 to 80% Regulatory and Safety FCC, CE, BSMI, CCC, UL, CB, RoHS, WEEE Pre-installed Operating System - Operating Systems Microsoft® Windows Server® 2003 R2, Standard Edition SP2 or later Microsoft® Windows Server® 2003 R2, Enterprise Edition SP2 or later Microsoft® Windows Server® 2003 R2, Standard x64 Edition SP2 or later Microsoft® Windows Server® 2003 R2, Enterprise x64 Edition SP2 or later Microsoft® Windows Server® 2008 Standard Microsoft® Windows Server® 2008 Standard (x64) Microsoft® Windows Server® 2008 Enterprise Microsoft® Windows Server® 2008 Enterprise (x64) Microsoft® Windows Server® 2008 R2 Standard Microsoft® Windows Server® 2008 R2 Enterprise 3 Red Hat Enterprise Linux 5.6 or later 3 Red Hat Enterprise Linux 5.6 or later (EM64T) 3 Red Hat Enterprise Linux 6.0 or later (x86) 3 Red Hat Enterprise Linux 6.0 or later (x86_64) 1 2 3 The on-board SATA RAID controller is not supported on Linux operating systems. Noise emission was measured in accordance with ISO 7779. The actual value may vary by the operating environment. For Linux support, contact our sales representative or go to the NEC website at: http://www.nec.com/global/prod/express/linux/index.html NEC Corporation Revision 2.3, May 2012 6 CONFIGURATION GUIDE – NEC Express5800/R110d-1E External Views Front and Rear Views Front View for 2.5-inch Drive Model A BC D E F G H I J KL M Front View for 3.5-inch Drive Model A BC D E F G H I J KL M Legend A. USB Connectors H. Pull-out Tab B. Power LED I. Drive Bays C. Data LAN 1 Activity LED J. Hard Drive Activity LED Data LAN 2 Activity LED D. UID LED K. E. BMC Reset Switch L. System Status LED F. UID LED Button M. Dump (NMI) Switch G. Power Button NEC Corporation Revision 2.3, May 2012 7 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Rear View A B F C G D E H I J Legend A. AC Inlet F. VGA Connector B. Serial Port Connector G. Power LED C. Data LAN 1 Connector H. USB Connectors D. Data LAN 2 Connector I. Management LAN Connector PCI Slots J. UID LED / Button E. Dimensions (mm) 44.3 mm 615.2 mm 482.0 mm 485.0 mm 444.0 mm 43.6 mm 740.9 mm NEC Corporation Revision 2.3, May 2012 8 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Configuration Diagram 2.5-inch Drive Model HDD Bay HDD Bay HDD Bay DIMM #1 DIMM #2 DIMM #3 DIMM #4 Processor Media Bay #1 PCIe 2.0 x8 (x16 socket) LP/MD2 Media Bay #1 PCIe 2.0 x8 (x8 socket) LP/MD2 Legend: BBU slot #1 BBU slot #2 Minimum requirement components HDD Bay 2.5-inch HDD Cage Fixed Power Supply HDD Bay CHASSIS FRONT HDD Bay CHASSIS REAR Standard components 3.5-inch Drive Model CHASSIS FRONT Media Bay #1 HDD Bay Processor Media Bay #1 DIMM #1 DIMM #2 DIMM #3 DIMM #4 HDD Bay 3.5-inch HDD Cage Fixed Power Supply HDD Bay CHASSIS REAR PCIe 2.0 x8 (x8 socket) LP/MD2 Legend: NEC Corporation BBU slot #1 HDD Bay PCIe 2.0 x8 (x16 socket) LP/MD2 BBU slot #2 Minimum requirement components Revision 2.3, May 2012 Standard components 9 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Server Configuration 1 Base Models Product Name / Description Part Number NEC EXPRESS5800/R110d-1E Server no processor, no RAM, no 3.5-inch HDD Including: 3.5-inch HDD Cage, EXPRESSBUILDER DVD NEC EXPRESS5800/R110d-1E Server no processor, no RAM, no 2.5-inch HDD Including: 2.5-inch HDD Cage, EXPRESSBUILDER DVD N8100-1744F N8100-1745F NOTE: The base model must be ordered with a processor kit. 2 Processor Available sockets: 1 Product Name / Description Part Number Processor Kit (2C/G630) Intel® Pentium® Processor G630 (2.70GHz / 2C-2T / 3MB) Processor Kit (4C/E3-1220) Intel® Xeon® Processor E3-1220 (3.10 GHz / 4C-4T / 8 MB) Processor Kit (4C/E3-1270) Intel® Xeon® Processor E3-1270 (3.40 GHz / 4C-8T / 8 MB) N8101-529F N8101-506F N8101-507F NOTE: One processor kit from above must be installed. The processor kit must be ordered with the base model. 3 Memory Available slots: 4 Product Name / Description Part Number 2GB Memory Kit 2GB (1x 2 GB) DDR3-1333 ECC Unbuffered DIMM 4GB Memory Kit 4GB (1x 4 GB) DDR3-1333 ECC Unbuffered DIMM 8GB Memory Kit 8GB (1x 8 GB) DDR3-1333 ECC Unbuffered DIMM N8102-416F N8102-417F N8102-418F NOTE: Minimum one memory kit must be installed. It is recommended to install two identical memory kits for dual-channel symmetric configuration to increase memory transfer speed. Actual DIMM speed is set to 1066 MHz when you choose Pentium Processor. NEC Corporation Revision 2.3, May 2012 10 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Maximum Available Memory See the table below for the maximum memory size that you can actually use on your system. The maximum available memory is less than the maximum physical memory supported by your system because some chipsets require PCI resource space of about 750MB. PCI resource requirements vary depending on the type and the number of PCI cards you are using. Maximum Memory Size Supported by OS Maximum Available Memory 4 GB Microsoft Windows Server 2003 R2, Standard Edition Microsoft Windows Server 2008 Standard 4 GB (HW-DEP enabled) App. 3.3 GB (HW-DEP disabled) 32 GB Microsoft Windows Server 2003 R2, Standard x64 Edition Microsoft Windows Server 2008 Standard (x64) Microsoft Windows Server 2008 R2 Standard (x64) 32 GB 64 GB Microsoft Windows Server 2003 R2, Enterprise Edition Microsoft Windows Server 2008 Enterprise 32 GB 1 TB Microsoft Windows Server 2003 R2, Enterprise x64 Edition 32 GB 2 TB Microsoft Windows Server 2008 Enterprise (x64) Microsoft Windows Server 2008 R2 Enterprise (x64) 32 GB 16 GB Red Hat Enterprise Linux 5 Red Hat Enterprise Linux 6 16 GB 256 GB Red Hat Enterprise Linux 5 (EM64T) 32 GB 2 TB Red Hat Enterprise Linux 6.0 (x86_64) 32 GB 4 Internal Hard Disk Drives 4.1 RAID Configuration Refer to the section in accordance with your disk form factor and RAID configuration. 4.1.1 3.5-inch Drive Available Disk Refer to 4.2.1 SATA 128MB Cache Refer to 4.2.2 SATA 256MB Cache Refer to 4.2.3 SATA 256MB Cache Refer to 4.2.4 SATA 512MB Cache Refer to 4.2.5 SATA Non-RAID On-board SATA RAID Controller RAID 0/1/10 Optional RAID Controller RAID 5/6 NOTE: On-board SATA RAID controller is supported only on Windows operating systems. An optional RAID controller is required to configure RAID array for other operating systems. On-board SATA RAID Controller does not support RAID 10 configured with 2TB and 3TB HDDs. Hot plug insertion/removal is not supported with the on-board SATA non-RAID controller. All hard drives within a RAID array should be of the same capacity. An optional RAID controller occupies one PCI slot. NEC Corporation Revision 2.3, May 2012 11 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.1.2 Up to four 2.5-inch Drive Available Disk Refer to 4.2.6 SATA, SSD 128MB Cache Refer to 4.2.7 SAS, SATA, SSD 256MB Cache Refer to 4.2.8 SAS, SATA, SSD 256MB Cache Refer to 4.2.9 SAS, SATA, SSD 512MB Cache Refer to 4.2.10 SAS, SATA, SSD Non-RAID On-board SATA RAID Controller RAID 0/1 Optional RAID Controller RAID 5/6 NOTE: On-board SATA RAID controller is supported only on Windows operating systems. An optional RAID controller is required to configure RAID array for other operating systems. Hot plug insertion/removal is not supported with the on-board SATA non-RAID controller. All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. An optional RAID controller occupies one PCI slot. 4.1.3 Up to six 2.5-inch Drive Available Disk RAID 0/1/10 128MB Cache Refer to 4.2.11 SAS, SATA, SSD 256MB Cache Refer to 4.2.12 SAS, SATA, SSD 256MB Cache Refer to 4.2.13 SAS, SATA, SSD 512MB Cache Refer to 4.2.14 SAS, SATA, SSD RAID 5/6 NOTE: An optional RAID controller occupies one PCI slot. All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 2.3, May 2012 12 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2 Internal Drive Configuration 4.2.1 3.5-inch Drive with On-board SATA Controller Category Product Name / Description Part Number Storage Controller On-board SATA Controller 4 x SATA ports, RAID 0/1 capable Internal SATA Cable 1x SATA to 1x SATA, 4 sets 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 160 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm 3TB HDD 1 x 3 TB, 3.5-inch, SATA2, 7,200 rpm (Standard) Cable HDD Cage HDD 4 slots available (Standard) (Standard) N8150-285 N8150-279 N8150-280 N8150-282 N8150-283 N8150-336 NOTE: On-board SATA RAID controller is supported only on Windows operating systems. An optional RAID controller is required to configure RAID array for other operating systems. On-board SATA RAID Controller does not support RAID 10 configured with 2TB and 3TB HDDs. Hot plug insertion/removal is not supported with the on-board SATA non-RAID controller. 3 TB HDDs are not supported with the on-board SATA non-RAID controller. All hard drives within a RAID array should be of the same capacity. NEC Corporation Revision 2.3, May 2012 13 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.2 3.5-inch Drive with RAID 0/1 Controller with 128 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (128MB, RAID 0/1) Promise SuperTrak TX8760T-128 RAID 0/1/10, 128MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 Internal SATA Cable 1x mini-SAS to 4x SATA 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 160 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm 3TB HDD 1 x 3 TB, 3.5-inch, SATA2, 7,200 rpm N8103-128 RAID BBU Recommended Cable Required HDD Cage HDD 4 slots available N8103-140 K410-240(00) (Standard) N8150-285 N8150-279 N8150-280 N8150-282 N8150-283 N8150-336 NOTE: All hard drives within a RAID array should be of the same capacity. NEC Corporation Revision 2.3, May 2012 14 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.3 3.5-inch Drive with RAID 0/1 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1) LSI MegaRAID SAS 9264-8i RAID 0/1, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SATA Cable 1x mini-SAS to 4x SATA 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 160 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm N8103-129 RAID BBU Recommended Cable Required HDD Cage HDD 4 slots available N8103-123 K410-240(00) (Standard) N8150-285 N8150-279 N8150-280 N8150-282 N8150-283 NOTE: All hard drives within a RAID array should be of the same capacity. 4.2.4 3.5-inch Drive with RAID 5/6 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1/5/6) LSI MegaRAID SAS 9264-8i RAID 0/1/5/6/10/50, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SATA Cable 1x mini-SAS to 4x SATA 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 160 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm N8103-130 RAID BBU Recommended Cable Required HDD Cage HDD 4 slots available N8103-123 K410-240(00) (Standard) N8150-285 N8150-279 N8150-280 N8150-282 N8150-283 NOTE: All hard drives within a RAID array should be of the same capacity. NEC Corporation Revision 2.3, May 2012 15 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.5 3.5-inch drive with RAID 5/6 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (512MB, RAID0/1/5/6) Promise SuperTrak EX8760T-512 RAID 0/1/5/6/10/50, 512MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 Internal SATA Cable 1x mini-SAS to 4x SATA 3.5-inch HDD Cage 4 x 3.5-inch hot plug hard drive bays 160GB HDD 1 x 160 GB, 3.5-inch, SATA2, 7,200 rpm 250GB HDD 1 x 250 GB, 3.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 3.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 3.5-inch, SATA2, 7,200 rpm 2TB HDD 1 x 2 TB, 3.5-inch, SATA2, 7,200 rpm 3TB HDD 1 x 3 TB, 3.5-inch, SATA2, 7,200 rpm N8103-134 RAID BBU Recommended Cable Required HDD Cage HDD 4 slots available N8103-140 K410-240(00) (Standard) N8150-285 N8150-279 N8150-280 N8150-282 N8150-283 N8150-336 NOTE: All hard drives within a RAID array should be of the same capacity. 4.2.6 2.5-inch Drive with On-board SATA Controller Category Product Name / Description Part Number Storage Controller On-board SATA Controller 4 x SATA ports, RAID 0/1/10 capable Internal SATA Cable 1x mini-SAS to 4x SATA 2.5-inch HDD Cage 6 x 2.5-inch hot plug hard drive bays 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 (Standard) Cable Required HDD Cage HDD 4 slots available SATA SSD (Standard) (Standard) N8150-276 N8150-277 N8150-334 N8150-707 NOTE The on-board SATA RAID controller is not supported on Linux operating systems. All hard drives within a RAID array should be of the same capacity. NEC Corporation Revision 2.3, May 2012 16 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.7 Up to four 2.5-inch Drive with RAID 0/1 Controller with 128 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (128MB, RAID 0/1) Promise SuperTrak TX8760T-128 RAID 0/1, 128MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 Internal SAS/SATA Cable 1x mini-SAS to 4x SATA 2.5-inch HDD Cage 6 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-128 RAID BBU Recommended Cable Required HDD Cage HDD 4 slots available SAS SATA SSD N8103-140 K410-240(00) (Standard) N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 2.3, May 2012 17 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.8 Up to four 2.5-inch Drive with RAID 0/1 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1) LSI MegaRAID SAS 9264-8i RAID 0/1, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1x mini-SAS to 4x SATA 2.5-inch HDD Cage 6 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-129 RAID BBU Recommended Cable Required HDD Cage HDD 4 slots available SAS SATA SSD N8103-123 K410-240(00) (Standard) N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported NEC Corporation Revision 2.3, May 2012 18 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.9 Up to four 2.5-inch Drive with RAID 5/6 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1/5/6) LSI MegaRAID SAS 9264-8i RAID 0/1/5/6/10/50, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1x mini-SAS to 4x Fixed SAS 2.5-inch HDD Cage 6 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-130 RAID BBU Recommended Cable Required HDD Cage HDD 4 slots available SAS SATA SSD N8103-123 K410-240(00) (Standard) N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 2.3, May 2012 19 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.10 Up to four 2.5-inch Drive with RAID 5/6 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (512MB, RAID0/1/5/6) Promise SuperTrak EX8760T-512 RAID 0/1/5/6/10/50, 512MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 Internal SAS/SATA Cable 1x mini-SAS to 4x SATA 2.5-inch HDD Cage 6 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-134 RAID BBU Recommended Cable Required HDD Cage HDD 4 slots available SAS SATA SSD N8103-140 K410-240(00) (Standard) N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported NEC Corporation Revision 2.3, May 2012 20 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.11 Up to six 2.5-inch Drive with RAID 0/1 Controller with 128 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (128MB, RAID 0/1) Promise SuperTrak TX8760T-128 RAID 0/1, 128MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 Internal SAS/SATA Cable 1x mini-SAS to 4x SATA Internal SAS/SATA Cable 1x mini-SAS to 4x SATA 2.5-inch HDD Cage 6 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-128 RAID BBU Recommended Cable 1 to4 HD Required 5 to6 HD HDD Cage HDD 6 slots available SAS SATA SSD N8103-140 K410-240(00) K410-204(00) (Standard) N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported NEC Corporation Revision 2.3, May 2012 21 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.12 Up to six 2.5-inch Drive with RAID 0/1 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1) LSI MegaRAID SAS 9264-8i RAID 0/1, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1x mini-SAS to 4x SATA Internal SAS/SATA Cable 1x mini-SAS to 4x SATA 2.5-inch HDD Cage 6 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-129 RAID BBU Recommended Cable 1 to4 HD Required 5 to6 HD HDD Cage HDD 6 slots available SAS SATA SSD N8103-123 K410-240(00) K410-204(00) (Standard) N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported NEC Corporation Revision 2.3, May 2012 22 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.13 Up to six 2.5-inch Drive with RAID 5/6 Controller with 256 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (256MB, RAID 0/1/5/6) LSI MegaRAID SAS 9264-8i RAID 0/1/5/6/10/50, 256MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for LSI MegaRAID SAS 9264 Internal SAS/SATA Cable 1x mini-SAS to 4x SATA Internal SAS/SATA Cable 1x mini-SAS to 4x SATA 2.5-inch HDD Cage 6 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-130 RAID BBU Recommended Cable 1 to4 HD Required 5 to6 HD HDD Cage HDD 6 slots available SAS SATA SSD N8103-123 K410-240(00) K410-204(00) (Standard) N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported. NEC Corporation Revision 2.3, May 2012 23 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 4.2.14 Up to six 2.5-inch Drive with RAID 5/6 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller(512MB, RAID0/1/5/6) Promise SuperTrak EX8760T-512 RAID 0/1/5/6/10/50, 512MB, Int. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 Internal SAS/SATA Cable 1x mini-SAS to 4x SATA Internal SAS/SATA Cable 1x mini-SAS to 4x SATA 2.5-inch HDD Cage 6 x 2.5-inch hot plug hard drive bays 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 300GB HDD 1 x 300 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 450GB HDD 1 x 450 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 600GB HDD 1 x 600 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 900GB HDD 1 x 900 GB, 2.5-inch, SAS 6Gb/s, 10,000 rpm 73.2GB HDD 1 x 73.2 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 146.5GB HDD 1 x 146.5 GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 300GB HDD 1 x 300GB, 2.5-inch, SAS 6Gb/s, 15,000 rpm 160GB HDD 1 x 160 GB, 2.5-inch, SATA2, 7,200 rpm 500GB HDD 1 x 500 GB, 2.5-inch, SATA2, 7,200 rpm 1TB HDD 1 x 1 TB, 2.5-inch, SATA2, 7,200 rpm 100GB SSD 1 x 100 GB, 2.5-inch, SATA2 N8103-134 RAID BBU Recommended Cable 1 to4 HD Required 5 to6 HD HDD Cage HDD 6 slots available SAS SATA SSD N8103-140 K410-240(00) K410-204(00) (Standard) N8150-374 N8150-375 N8150-376 N8150-377 N8150-332 N8150-378 N8150-379 N8150-331 N8150-276 N8150-277 N8150-334 N8150-707 NOTE: All hard drives within a RAID array should be of the same capacity and rotation speed. Mixing SAS and SATA hard drives in the same system is not supported NEC Corporation Revision 2.3, May 2012 24 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 5 Optical Drive Category Product Name / Description Part Number Internal 1 slot available Internal Slim DVD-ROM drive Slim DVD-ROM drive Internal DVD Super Multi Drive Slim DVD Super Multi drive, not including writing software External DVD-ROM drive Slim DVD-ROM drive, Bus powered, 0.8 A required N8151-100 External N8151-104F N8160-85 NOTE: Up to 1 optical drive can be connected. 6 Internal Flash Memory Available socket: 1 Product Name / Description Part Number Internal Flash Memory Internal flash memory to enable software and tools in the EXPRESSBUILDR DVD without DVD media NOTE: Before use, software and tools must be copied from the EXPRESSBUILDER DVD to the flash memory. The following operations can be performed with the flash memory: - Installation of Windows server with express setup - Installation of Starter Pack—the package of NEC qualified drivers and system setting tools - Installation of NEC ESMPRO Agent and Universal RAID Utility - Performance of the Test and Diagnosis Tool N8115-07 NEC Corporation Revision 2.3, May 2012 25 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 7 PCI Card 7.1 LAN Controller Category Product Name / Description Part Number GbE 1000BASE-T Adapter (2ch) Broadcom NetXtreme II 5709 Dual port Network Interface Card PCIe x4, LP / FH NOTE: Teaming and bonding features across the standard LAN and the LAN controller are supported on Windows Server 2003R2 / 2008 / 2008R2 and Red Hat Linux 5.x/6.x Operating system. Up to 2 teams per system and 2 ports per team is supported in the teaming and bonding feature. N8104-134 Ctrlr 10GBASE Adapter (SFP+/2ch) Broadcom NetXtreme II BCM957711 10G SFP+ Dual Port Network Interface Card PCIe 2.0 x8, LP / FH NOTE: N8104-129 SFP+ Module is required to connect with an optical cable. Up to 2 SFP+ Modules can be installed. 1 team per 1 system is supported in teaming feature. N8104-128 Module SFP+ Module (10G-SR) 1x SFP+ Module for N8104-128 N8104-129 10GbE 7.2 External RAID Controller Category Product Name / Description Part Number Controller RAID Controller (512MB, RAID0/1/5/6) Promise SuperTrak EX8768 RAID 0/1/5/6, 512MB, Ext. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 3Gb/s, LP / FH RAID Battery Backup Unit for Promise SuperTrak EX8760T and EX8768 N8103-135 RAID BBU NEC Corporation Revision 2.3, May 2012 N8103-140 26 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 7.3 Fibre Channel/SAS/SCSI Controller Category Product Name / Description Part Number Fibre Channel Fibre Channel Controller (1ch) Emulex LightPulse LPe1250-F8 Host Bus Adapter 8Gb/s, Optical, PCIe 2.0 x8, LP / FH Fibre Channel Controller (2ch) Emulex LightPulse LPe12002-M8 Host Bus Adapter 8Gb/s, Optical, PCIe 2.0 x8, LP / FH Fibre Channel Controller (1ch) Emulex LightPulse LPe1150-F4 Host Bus Adapter 4Gb/s, Optical, PCIe x4, LP / FH Fibre Channel Controller (2ch) Emulex LightPulse LPe11002-M4 Host Bus Adapter 4Gb/s, Optical, PCIe 2.0 x4, LP / FH SAS Controller LSI SAS3442E-R Host Bus Adapter 3Gb/s SAS, Int. 4 / Ext. 4, SFF-8484 / SFF8470, PCIe x8, LP/FH SAS Controller LSI SAS9212-4i4 Host Bus Adapter 6Gb/s SAS, Int. 4 / Ext. 4, 7-pin SATA / SFF-8088, PCIe 2.0 x8, LP/FH N8190-153 SAS 7.4 N8190-154 N8190-127 N8190-131 N8103-104A N8103-142 Serial Port Adapter Product Name / Description Part Number Serial port adapter Serial port fixed to PCI bracket N8117-01A 8 Add-on Components 8.1 17-inch LCD Console Drawer Category Drawer w/ KVM Drawer Cable Drawer w/o KVM NEC Corporation Drawer Product Name / Description Part Number 17inch LCD Console Unit (1U/8port) 17-inch LCD, US 83-keys Keyboard, Optical mouse, 8 port KVM switch, 1U height Switch Unit Connection Cable Set (USB,1.8m) 1.8 m, 1x 15-pin mini D-sub to 1x 15-pin mini D-sub / 1x 4-pin USB A Switch Unit Connection Cable Set (USB,3m) 3 m, 1x 15-pin mini D-sub to 1x 15-pin mini D-sub / 1x 4-pin USB A Switch Unit Connection Cable Set (USB,5m) 5 m, 1x 15-pin mini D-sub to 1x 15-pin mini D-sub / 1x 4-pin USB A 17inch LCD Console Unit 1U 17-inch LCD, US 83-keys Keyboard, Optical mouse, 1U height, 1x 4-pin USB B to 4-pin USB A cable 2m, 1x PS/2 Y-splitter cable 2m, 15-pin mini D-sub VGA cable 2m N8143-69F Revision 2.3, May 2012 K410-118(1A) K410-118(03) K410-118(05) N8143-76F 27 CONFIGURATION GUIDE – NEC Express5800/R110d-1E 8.2 KVM Switch Category Product Name / Description Part Number KVM Switch Server Switch Unit (8 server) 1U USB 8 port KVM switch Switch Unit Connection Cable Set (USB,1.8m) 1.8 m, 1x 15-pin mini D-sub to 1x 15-pin mini D-sub / 1x 4-pin USB A Switch Unit Connection Cable Set (USB,3m) 3 m, 1x 15-pin mini D-sub to 1x 15-pin mini D-sub / 1x 4-pin USB A Switch Unit Connection Cable Set (USB,5m) 5 m, 1x 15-pin mini D-sub to 1x 15-pin mini D-sub / 1x 4-pin USB A N8191-10F Cable 8.3 K410-118(1A) K410-118(03) K410-118(05) Server Management License The server integrates the EXPRESSSCOPE Engine 3 as standard. Refer to Server Management for the standard management features. For more extensive remote KVM and remote media features, choose the following kit. Product Name / Description Part Number Remote KVM and Media License kit N8115-04 License for one server. Remote console and remote media are enabled regardless of OS status. Remote KVM: Displays a graphics console on the web browser of the remote terminal (PC/server). Controls keyboard and mouse via the remote terminals' web browser Remote media: Enables the user to use the CD / DVD / FD / Flash memory of the remote terminals (PC/server) as if accessing the local drives. 8.4 Flash FDD Choose the Flash FDD if you need to prepare an alternative device for a floppy drive. Product Name / Description Part Number Flash FDD USB flash emulating USB floppy disk, Native capacity 1.44 MB N8160-86 8.5 Front Bezel Product Name / Description Part Number Front Bezel Front bezel for R110d-1E N8146-20F NEC Corporation Revision 2.3, May 2012 28 CONFIGURATION GUIDE – NEC Express5800/R110d-1E References Note for Ordering Parts number provided may be needed to modify by country/region when you order the products. For example, the operable parts number for N8100-1738F in EMEA is N8100-1730F-O, adding "-O", the country-specific identifier for EMEA, after the parts number. Please consult our sales representative for your country identifier. Server Management The EXPRESSSCOPE Engine 3, integrated into the server, provides superior remote control and system management features listed in the table below. Standard Hardware monitoring Temperature/voltage/power/ fan /degeneration (memory/hard drive) Hardware event log collection Boot monitoring Booting, BIOS/POST stall, OS stall, shutdown Alerting HW error, Boot error and OS panic (by SNMP, E-Mail) Remote KVM POST/BIOS setup, DOS utility (via LAN) Panic screen, Boot screen Text-based screen (OS console) GUI-based screen (OS console) - Remote reset/power on-off/ dump 1 Configure BIOS setting (items limited) OS shutdown Remote media (CD/DVD/FD) - Server Management Command Line Protocol (DMTF compliant) Remote control via Web browser (without dedicated app) Remote batch Scheduling (without UPS) Maintenance Save/restore BIOS/BMC setting to/from a dedicated flash memory Others Set automatic IP address via DNS/DHCP Remote wakeup Wake On LAN, Wake On Ring Centralized management Industry standard Monitoring and control of multiple servers IPMI 2.0 2.0 Remote control (via LAN) 1 With Remote KVM and Media License kit Configure power capping setting The power capping feature is supported by Xeon processor. NEC Corporation Revision 2.3, May 2012 29 CONFIGURATION GUIDE – NEC Express5800/R110d-1E OS Support Matrix for PCI Cards RHEL 6 x64 RHEL 6 RHEL 5 x64 RHEL 5 WS 2003R2 x64 WS 2003R2 WS 2008 x64 WS 2008 WS 2008R2 Part Number Product Name N8103-128 RAID Controller N8103-129 RAID Controller N8103-130 RAID Controller N8103-134 RAID Controller N8103-135 RAID Controller N8103-104A SAS Controller, 3 Gb/s - - N8103-142 SAS Controller, 6 Gb/s - - N8190-153 Fibre Channel Controller - - N8190-154 Fibre Channel Controller (2ch) - - N8190-127 Fibre Channel Controller - - N8190-131 Fibre Channel Controller (2ch) - - N8104-134 1000BASE-T Adapter (2ch) N8104-128 10GBASE Adapter (SFP+/2ch) - NEC Corporation Revision 2.3, May 2012 - 30 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Supporting PCI cards and Installable Slots Parts Number Product Name Slots Slot # : #1 #2 PCI Slot: X8 X8 Card height: Low-Profile Slot type: X16 x8 Installable card length (mm) : 200 (LP) N8103-104A SAS Controller [PCIe x8] N8103-142 SAS Controller [PCIe 2.0 x8] N8103-128 RAID Controller (128MB, RAID 0/1) [PCIe 2.0 x8] - N8103-129 RAID Controller (256MB, RAID 0/1) [PCIe 2.0 x8] - N8103-130 RAID Controller (256MB, RAID 0/1/5/6) [PCIe 2.0 x8] - N8103-134 RAID Controller (512MB, RAID 0/1/5/6) [PCIe 2.0 x8] - N8103-135 RAID Controller (512MB, RAID 0/1/5/6) [PCIe 2.0 x8] N8190-127 Fibre Channel Controller [PCIe x4] N8190-153 Fibre Channel Controller [PCIe 2.0 x8] N8190-131 Fibre Channel Controller (2ch) [PCIe x4] N8190-154 Fibre Channel Controller (2ch) [PCIe 2.0 x8] N8104-134 1000BASE-T adapter(2ch) [PCIe x4] N8104-128 10GBASE Adapter(SFP+/2ch) [PCIe 2.0 x8] N8117-01A Serial Port Adapter NEC Corporation Revision 2.3, May 2012 Remarks 31 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Copyright Notice and Liability Disclaimer The information contained herein is subject to change without notice. Microsoft and Windows Server are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries Intel and Xeon are registered trademarks or trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Linux is a trademark of Linus Torvalds. Red Hat is a registered trademark of Red Hat, Inc. in the U.S. All other products, brands, or trade names used in this document are trademarks or registered trademarks of their respective holders. NEC shall not be liable for technical or editorial errors or omissions contained herein. For hard drive capacity measurements, 1 GB = 1 billion bytes. Actual formatted capacity is less. NEC Corporation Revision 2.3, May 2012 32 CONFIGURATION GUIDE – NEC Express5800/R110d-1E Revision History Revision Date Description 2.4 May 29, 2012 Others: Correct incorrect card height: for PCI slots 2.3 February 13, 2012 Part number changed: 146.5GB 2.5-inch SAS HDD / N8150-374 300GB 2.5-inch SAS HDD / N8150-375 450GB 2.5-inch SAS HDD / N8150-376 600GB 2.5-inch SAS HDD / N8150-377 2.2 January 23, 2012 Part number changed: 73.2GB 2.5-inch SAS HDD / N8150-378 146.5GB 2.5-inch SAS HDD / N8150-379 2.1 January 11, 2012 New products added: Pentium G630 / N8101-529F Discontinued products removed: Pentium G620 / N8101-505F SCSI Controller / N8103-107 Others: Correct incorrect information in internal drive configuration using 3TB 3.5-inch SATA drive 2.0 December 14, 2011 New products added: 3TB HDD / N8150-336 Discontinued products removed: 1GB Memory Kit / N8102-415F 1.3 October 18, 2011 Others: Correct incorrect information in Specification, 3 Memory, 7.1 LAN Controller, 7.3 Fibre Channel/SAS/SCSI Controller, 8.1 17-inch LCD Console Drawer, and References. 1.2 August 15, 2011 Others: Correct incorrect part number for the cable in section 4.2.6 Add the note for the on-board SATA controller 1.1 August 3, 2011 Others: Correct incorrect description for 8GB Memory Kit 1.0 July 28, 2011 Initial release NEC Corporation Revision 2.3, May 2012 33