www.osram.com PrevaLED® Bar Light Engines 1100lm on 280 x 55mm 2200lm on 560 x 55mm Benefits Efficiency 155lm/W • • • • • • • • • Perfect match to LEDiL Florence 3R lenses Homogeneous light distribution Consistent white light of 3 SDCM Seamless: no shadows between modules Poke-in connectors for 0,5mm² to 0,75mm² wire Self-cooling SELV/non-SELV module for easier fixture design Average lifetime 50.000h L80B10 at Tp (max) = 55°C • CE, ENEC approval under preparation Application • Supermarket • Industry Dimension (l x w x h): • 280mm x 55mm x 6mm • 560mm x 55mm x 6mm Typical technical data @rated current* Flux CCT (lm) (K) Vf If P (W) lm/W* (V) (mA) Module Module PLG2-Bar-1100-830-280x55-DC 1100 3 31 225 7 155 PLG2-Bar-1100-840-280x55-DC > 80 3 31 225 7 155 6500 > 80 3 31 225 7 155 2200 3000 > 80 3 31 450 14 155 PLG2-Bar-2200-840-560x55-DC 2200 4000 > 80 3 31 450 14 155 PLG2-Bar-2200-865-560x55-DC 2200 6500 > 80 3 31 450 14 155 Product name CRI SDCM 3000 > 80 1100 4000 PLG2-Bar-1100-865-280x55-DC 1100 PLG2-Bar-2200-830-560x55-DC Typical values valid for Tp = 45°C Energy Efficiency Class according 2012/874/EC: A++ Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. * Tolerance for optical and electrical data: +/-10% PrevaLED Bar, December 2015 page 1 of 8 sram.com Typical performance @max. current* Flux CCT Vf If P (W) lm/W* (lm) (K) (V) (mA) Module Module PLG2-Bar-1100-830-280x55-DC 1730 3 33 400 13 133 PLG2-Bar-1100-840-280x55-DC > 80 3 33 400 13 133 6500 > 80 3 33 400 13 133 3460 3000 > 80 3 33 800 26 133 PLG2-Bar-2200-840-560x55-DC 3460 4000 > 80 3 33 800 26 133 PLG2-Bar-2200-865-560x55-DC 3460 6500 > 80 3 33 800 26 133 Product name CRI SDCM 3000 > 80 1730 4000 PLG2-Bar-1100-865-280x55-DC 1730 PLG2-Bar-2200-830-560x55-DC Typical values valid for Tp 45°C Optical parameters # LED Pitch (mm) PLG2-Bar-1100-8xx-280x55-DC 33 26mm PLG2-Bar-2200-8xx-560x55-DC 66 26mm Product name Minimum and Maximum Ratings Storage temperature [ °C ] Tc max.* (@ typ. current) L80 B10 @ Tc max. 55°C PLG2-Bar-1100-8xx-280x55-DC -35 … 80 80°C 50.000h PLG2-Bar-2200-8xx-560x55-DC -35 … 80 80°C 50.000h Product , The modules are designed for operation with OPTOTRONIC® ECG. *) Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the light engine. The temperature of the LED module must be measured at the tc-point according to EN60598-1 in thermally settled conditions with a temperature sensor. For exact location of the Tc -point see drawing below (marked as Tc1 and Tc2). PrevaLED Bar, December 2015 page 2 of 8 ww.osram.com Temperature derating 104,0% Relative Flux and Efficacy 102,0% 100,0% 98,0% Luminous Flux Efficacy 96,0% 94,0% 92,0% 0 20 40 60 Tcase 80 100 (oC) L80B10 lifetime [h] as a function of Tp PLG2-Bar-1100-8xx-280x55-DC PrevaLED Bar, December 2015 PLG2-Bar-2200-8xx-560x55-DC page 3 of 8 Modularity • The tables below show recommended combinations of the PrevaLED® Bar modules and Optotronic® drivers – but not all possible combinations. • Calculations in the tables are based on the nominal currents. If currents other than the nominal currents are requested, the driver – module compatibility tables change. • Numbers in brackets show possible combinations, but with currents noticeably smaller than the nominal currents. • In parallel connection 280mm and 560mm modules can be used together (e.g. to build a 1400mm luminiare 2 x 560mm modules and 1 x 280 mm modules can be used in parallel connection). In the modularity tables one 560 mm module counts as two 280 mm modules (e.g. to look up possible driver matches for the 2 x 560mm and 1 x 280 mm combination mentioned above, the easiest way is to look for 5 x 280 mm in the table). In serial connection 280mm and 560mm modules can not be used together. • XsYp is an abbreviation for X modules connected in series, Y modules connected in parallel. OT FIT CS (triple current driver – SELV) PrevaLED Bar is designed to be operated by OT FIT SELV drivers in parallel connection*. Current setting via cable bridge (linear drivers) or selectable output current connectors (compact drivers). Linear drivers OT FIT 27V – 54V OT FIT 80 / 220240 / 1A6 CS L OT FIT 50 / 220240 / 1A0 CS L Compact drivers OTe OTe OT FIT 35 / 22025/22025/220240 / 0A7 CS 240/420 CS 240/700 CS 1,2A / 1,4A / 1,55A 0,8A / 0,93A / 1,0A PrevaLED Bar * 0,5A / 0,6A / 0,7A 290 / 350 / 420 mA 500 / 600 / 700 mA 360 x 30 x 21mm 280 x 30 x 21mm 280 x 30 x 21mm 88 x 43 x 29.5 mm 88 x 43 x 29.5 mm PLG2-Bar-11008xx-280x55-DC 5,6,(7) 4 2,3 1 2,3 PLG2-Bar-22008xx-560x55-DC 3 2 1 (1) 1 Final release of modularity under evaluation. OTi DALI (wide window driver – SELV) PrevaLED Bar is designed to be operated by OTi DALI drivers in parallel connection*. Current setting via resistor coding (LEDSet) or Tuner4TRONIC software and DALI magic. OTi DALI 27V – 54V OTi DALI 80/220240/2A1 LT2 L OTi DALI 80/220240/1A6 LT2 L OTi DALI 50/220240/1A4 LT2 L OTi DALI 35/220240/700 LT2 L 1,0A – 2,1A 0,6A - 1,55A 0,6A - 1,4A 0,2A – 0,7A 360 x 30 x 21mm 360 x 30 x 21mm 360 x 30 x 21mm 360 x 30 x 21mm PLG2-Bar-1100-8xx280x55-DC 7,8,9 6 3,4,5 1,2 PLG2-Bar-2200-8xx560x55-DC 4 3 2 1 PrevaLED Bar * Final release of modularity under evaluation. PrevaLED Bar, December 2015 page 4 of 8 OT FIT D (single current driver – Non-SELV) PrevaLED Bar is designed to be operated by OT Fit D Non-SELV drivers in serial connection*. OT Fit D OT FIT 30/220-240/125 D OT FIT 50/220-240/250 D OT FIT 50/220-240/350 D L L L 125mA, 54V – 216V 250mA, 54V – 216V 350mA, 54V – 150V 210 x 30 x 21mm 210 x 30 x 21mm 210 x 30 x 21mm PLG2-Bar-11008xx-280x55-DC (2,3,4,5,6) 2,3,4,5,6 - PLG2-Bar-22008xx-560x55-DC - - (2,3) PrevaLED Bar * Final release of modularity under evaluation. OTi (wide window driver – Non-SELV) PrevaLED Bar is designed to be operated by OTi and OTi DALI drivers in serial or combined serial-parallel connection*. Current setting via resistor coding (LEDSet) and for OTi DALI drivers also via Tuner4TRONIC software and DALI magic. OTi OTi 60/220-240/550 OTi 90/220OTi DALI 60 550 D LT2 L 240V/1A0 D LT2 L 54V-240V 120mA – 550mA 250mA – 1000mA 125mA – 550mA 250mA – 1000mA 280 x 30 x 21mm 280 x 30 x 21mm 280 x 30 x 21mm 280 x 30 x 21mm PLG2-Bar-1100-8xx280x55-DC 2,3,4,5 (Xs1p) 6 (3s2p), 8(4s2p) 10 (5s2p) 2,3,4,5 (Xs1p) 6 (3s2p), 8(4s2p) 10 (5s2p) PLG2-Bar-2200-8xx560x55-DC 2,3,4 (Xs1p) 5 (Xs1p) 2,3,4 (Xs1p) 5 (Xs1p) PrevaLED Bar * OTi DALI 90 1A0 Final release of modularity under evaluation. Installation examples The installation examples 1 and 2 of the PrevaLED® Bar show the scenario of two 280mm modules connected in series and in parallel to an ECG (the cases 1s2p and 2s1p). Of course the same way of connecting is possible for the 560 mm modules. 1. Parallel connection (1s2p configuration – 280 mm modules) 2. Serial connection (2s1p configuration – 280 mm modules) PrevaLED Bar, December 2015 page 5 of 8 This examples can easily expanded to configurations with more than 2 modules, for example 3 modules in series (3s1p) or 4 modules in parallel – the way of connecting the modules remains the same, but additional modules are added. When connecting the modules in parallel to the ECG it is also possible to combine 280 mm and 560 mm modules. This is not possible for serial connection. For some cases the best solution is to use a combined serial and parallel connection of the modules. The picture below shows a possible way of connecting four 280 mm modules in 2s2p configuration. Please make sure to keep a clearance of minimum 1mm around the PrevaLED® Bar module If you have any further questions about installation of PrevaLED® Bar Light engines, please consult your local Osram Sales representative. Drawings PrevaLED Bar: PLG2-Bar-1100-8xx-280x55-DC PrevaLED Bar: PLG2-Bar-2200-8xx-560x55-DC PrevaLED Bar, December 2015 page 6 of 8 Optics LEDIL FLORENCE-3R 280mm PrevaLED Bar - PLG2-Bar-1100-8xx-280x55-DC is fully compatible with LEDIL FLORENCE-3R product family. FLORENCE-3R offers 4 optical versions. FLORENCE symmetrical beam Z30(30deg), Z60(60deg) and Z90(90deg) applications provide a uniform and low glare light distribution in advanced low bay environments with 90% efficiency. FLORENCE asymmetrical beam ZT25 application is designed especially for retail environments where items are illuminated on shelves on both sides of the aisle. ZT25 provides a uniform double sided asymmetric beam with a twenty degree tilt optimized to illuminate products on the shelves. Product Numer Viewing angle Light beam F14486_FLORENCE-Z30 29 deg Medium F14112_FLORENCE-Z60 57 deg Very wide F13853_FLORENCE-Z90 92 deg WWW-class F14170_FLORENCE-ZT25 Asymmertic deg Asymmetric F14112_FLORENCE-Z60 ¹ F14486_FLORENCE-Z30 ¹ F14486_FLORENCE-Z30 F14112_FLORENCE-Z90 ¹ F14170_FLORENCE-ZT25 ¹ ¹ not rated values PrevaLED Bar, December 2015 page 7 of 8 Ordering Codes Product name EAN (single product) Type Shipping Unit PLG2-Bar-1100-830-280x55-DC 4052899303935 Make to stock 40 x 1 PLG2-Bar-1100-840-280x55-DC 4052899303959 Make to stock 40 x 1 PLG2-Bar-1100-865-280x55-DC 4052899303973 Make to Order 40 x 1 PLG2-Bar-2200-830-560x55-DC 4052899303997 Make to stock 40 x 1 PLG2-Bar-2200-840-560x55-DC 4052899304017 Make to stock 40 x 1 PLG2-Bar-2200-865-560x55-DC 4052899304031 Make to Order 40 x 1 Safety Information • The LED module itself and all its components must not be mechanically stressed. The modules are intended for operation only with matching OPTOTRONIC®. To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. In Europe the declarations of conformity must include the following standards: CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384. Also check for the mark of an independent authorized certification institute. Please see the relevant brochure for more detailed information (see "Related and Further Information") • Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. • Pay attention to standard ESD precautions when installing the module. • Photobiological safety according to IEC 62471, risk group RG1 • Max. Voltage U-OUT = 250V for operation on non-isolated and SELV LED controlgear. Sales and Technical Support OSRAM GmbH Marcel-Breuer-Straße 6 D- Sales and technical support is given by the 80807 München local OSRAM subsidiaries. On our world wide homepage all OSRAM www.osram.com +49 89 6213-0 subsidiaries are listed with complete address and phone numbers. Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves. OSRAM GmbH Head Office: Marcel-Breuer-Strasse 6 80807 Munich, Germany Phone +49 89 6213-0 www.osram.com PrevaLED Bar, December 2015 page 8 of 8