IDT 830154AGI-08LF

Over-Voltage Tolerant 1.5V, 1:4 Fanout Buffer ICS830154I-08
DATA SHEET
General Description
Features
The ICS830154I-08 is an LVCMOS, over-voltage
tolerant clock fanout buffer targeted for clock
HiPerClockS™
generation in high-performance telecommunication,
networking and computing applications. The device is
optimized for low-skew clock distribution in low-voltage
applications. The input over-voltage tolerance enables using this
device in mixed-mode voltage applications. An output enable pin
controls whether the outputs are in the active or high impedance
state. Guaranteed output skew characteristics make the
ICS830154I-08 ideal for those applications demanding well defined
performance and repeatability. The ICS830154I-08 is packaged in a
small 8-TSSOP and in an 8-SOIC package.
•
•
•
•
•
•
•
•
•
ICS
CLK_IN
LVCMOS input and output levels
3.6V Over-voltage tolerance at the clock and control inputs
Supports clock frequencies up to 160MHz
LVCMOS compatible control input for output disable
Output disabled to a high-impedance state
-40°C to 85°C ambient operating temperature
Available in lead-free RoHS 6 packages (8-TSSOP, 8-SOIC)
CLK_IN
Q1
Q2
Q3
Q1
Q2
1
2
3
4
8
7
6
5
OE
VDD
GND
Q4
ICS830154AMI-08
8-SOIC, 150 mil
3.9mm x 4.9mm x 1.375mm package body
M-Package
Top View
Q3
Q4
OE
Supports 3.3V, 2.5V, 1.8V and 1.5V power supplies
Pin Assignments
Block Diagram
Pulldown
Low-skew 1:4 fanout buffer
Pullup
ICS830154AGI-08
8-TSSOP
4.4mm x 3.0mm x 0.925mm package body
G-Package
Top View
ICS830154AGI-08 REVISION A MARCH 29, 2010
1
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Table 1. Pin Descriptions
Number
Name
1
CLK_IN
Input
Type
Description
2
Q1
Output
Single-ended clock output. LVCMOS interface levels.
3
Q2
Output
Single-ended clock output. LVCMOS interface levels.
4
Q3
Output
Single-ended clock output. LVCMOS interface levels.
5
Q4
Output
Single-ended clock output. LVCMOS interface levels.
6
GND
Power
Power supply ground.
7
VDD
Power
Power supply pin.
8
OE
Input
Pulldown
Pullup
Single-ended clock input. LVCMOS interface levels.
Output enable pin. See Table 3. LVCMOS interface levels.
NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values.
Table 2. Pin Characteristics
Symbol
Parameter
CIN
Input Capacitance
Power Dissipation Capacitance
CPD
RPULLUP
Test Conditions
Maximum
Units
pF
VDD = 3.465V
14
pF
VDD = 2.375V
13
pF
VDD = 1.95V
13
pF
VDD = 1.6V
12
pF
51
kΩ
51
kΩ
VDD = 3.3V ± 5%
9
Ω
VDD = 2.5V ± 5%
10
Ω
VDD = 1.8V ± 0.15V
12
Ω
VDD = 1.5 ± 0.1V
15
Ω
Input Pullup Resistor
Output Impedance
Typical
4
RPULLDOWN Input Pulldown Resistor
ROUT
Minimum
Function Table
Table 3. OE Configuration Table
Input
OE
0
1 (default)
Operation
Q[4:1] disabled (high-impedance)
Q[4:1] enabled
NOTE: OE is an asynchronous control.
ICS830154AGI-08 REVISION A MARCH 29, 2010
2
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Absolute Maximum Ratings
NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device.
These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond
those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect product reliability.
Item
Rating
Supply Voltage, VDD
4.6V
Inputs, VI
3.6V
Outputs, VO
-0.5V to VDD + 0.5V
Package Thermal Impedance, θJA
8 Lead TSSOP
8 Lead SOIC
121.5°C/W (0 mps)
103°C/W (0 mps)
Storage Temperature, TSTG
-65°C to 150°C
DC Electrical Characteristics
Table 4A. Power Supply DC Characteristics, VDD = 3.3V ± 5%, TA = -40°C to 85°C
Symbol
Parameter
VDD
Power Supply Voltage
IDDQ
Quiescent Power Supply Current
Test Conditions
Minimum
Typical
Maximum
Units
3.135
3.3
3.465
V
1
mA
Inputs Open, Outputs Unloaded
Table 4B. Power Supply DC Characteristics, VDD = 2.5V ± 5%, TA = -40°C to 85°C
Symbol
Parameter
VDD
Power Supply Voltage
IDDQ
Quiescent Power Supply Current
Test Conditions
Minimum
Typical
Maximum
Units
2.375
2.5
2.625
V
1
mA
Inputs Open, Outputs Unloaded
Table 4C. Power Supply DC Characteristics, VDD = 1.8V ± 0.15V, TA = -40°C to 85°C
Symbol
Parameter
VDD
Power Supply Voltage
IDDQ
Quiescent Power Supply Current
Test Conditions
Minimum
Typical
Maximum
Units
1.65
1.8
1.95
V
1
mA
Inputs Open, Outputs Unloaded
Table 4D. Power Supply DC Characteristics, VDD = 1.5V ± 0.1V, TA = -40°C to 85°C
Symbol
Parameter
VDD
Power Supply Voltage
IDDQ
Quiescent Power Supply Current
ICS830154AGI-08 REVISION A MARCH 29, 2010
Test Conditions
Inputs Open, Outputs Unloaded
3
Minimum
Typical
Maximum
Units
1.4
1.5
1.6
V
1
mA
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Table 4E. LVCMOS DC Characteristics, VDD = 3.3V ± 5%, TA = -40°C to 85°C
Symbol
Parameter
VIH
Input High Voltage
VIL
Input Low Voltage
IIH
Input High Current
IIL
Input Low Current
VOH
Output High Voltage
VOL
Output Low Voltage
Test Conditions
Minimum
Typical
Maximum
Units
0.65 * VDD
3.6
V
-0.3
0.35 * VDD
V
CLK_IN
VDD = VIN = 3.465V
150
µA
OE
VDD = VIN = 3.465V
5
µA
CLK_IN
VDD = 3.465V, VIN = 0V
-5
µA
OE
VDD = 3.465V, VIN = 0V
-150
µA
Q[4:1]
IOH = -12mA
2.6
V
Q[4:1]
IOL = 12mA
0.5
V
Maximum
Units
Table 4F. LVCMOS DC Characteristics, VDD = 2.5V ± 5%, TA = -40°C to 85°C
Symbol
Parameter
Test Conditions
Minimum
Typical
VIH
Input High Voltage
0.65 * VDD
3.6
V
VIL
Input Low Voltage
-0.3
0.35 * VDD
V
IIH
Input High Current
IIL
Input Low Current
VOH
Output High Voltage
VOL
Output Low Voltage
CLK_IN
VDD = VIN = 2.625V
150
µA
OE
VDD = VIN = 2.625V
5
µA
CLK_IN
VDD = 2.625V, VIN = 0V
-5
µA
OE
VDD = 2.625V, VIN = 0V
-150
µA
Q[4:1]]
IOH = -12mA
1.8
V
Q[4:1]
IOL = 12mA
0.5
V
Table 4G. LVCMOS DC Characteristics, VDD = 1.8V ± 0.15V, TA = -40°C to 85°C
Symbol
Parameter
VIH
Input High Voltage
VIL
Input Low Voltage
IIH
Input High Current
IIL
Input Low Current
VOH
Output High Voltage
VOL
Output Low Voltage
Test Conditions
CLK_IN
Minimum
Maximum
Units
0.65 * VDD
3.6
V
-0.3
0.35 * VDD
V
150
µA
5
µA
VDD = VIN = 1.95V
OE
Typical
CLK_IN
VDD = 1.95V, VIN = 0V
-5
µA
OE
VDD = 1.95V, VIN = 0V
-150
µA
Q[4:1]
IOH = -6mA
VDD – 0.45
V
Q[4:1]
IOL = 6mA
ICS830154AGI-08 REVISION A MARCH 29, 2010
4
0.45
V
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Table 4H. LVCMOS DC Characteristics, VDD = 1.5V ± 0.1V, TA = -40°C to 85°C
Symbol
Parameter
VIH
Input High Voltage
VIL
Input Low Voltage
IIH
Input High Current
IIL
Input Low Current
VOH
Output High Voltage
VOL
Output Low Voltage
Test Conditions
Minimum
Typical
Maximum
Units
0.65 * VDD
3.6
V
-0.3
0.35 * VDD
V
CLK_IN
VDD = VIN = 1.6V
150
µA
OE
VDD = VIN = 1.6V
5
µA
CLK_IN
VDD = 1.6V, VIN = 0V
-5
µA
OE
VDD = 1.6V, VIN = 0V
-150
µA
Q[4:1]
IOH = -4mA
0.75 * VDD
V
Q[4:1]
IOL = 4mA
0.25 * VDD
V
Maximum
Units
160
MHz
AC Electrical Characteristics
Table 5A. AC Characteristics, VDD = 3.3V ± 5%, TA = -40°C to 85°C
Symbol
Parameter
fOUT
Output Frequency
tpLH
Propagation Delay
(low to high transition); NOTE 1
0.7
1.45
ns
tpHL
Propagation Delay
(high to low transition); NOTE 1
0.7
1.45
ns
tPLZ, tPHZ
Disable Time
(active to high-impedance)
10
ns
tPZL, tPZH
Enable Time
(high-impedance to disable)
10
ns
tsk(o)
Output Skew; NOTE 2, 3
250
ps
tsk(pp)
Part-to-Part Skew; NOTE 2, 4
800
ps
tjit
Buffer Additive Phase Jitter, RMS;
refer to Additive Phase Jitter Section
t R / tF
Output Rise/Fall Time
odc
Output Duty Cycle
Test Conditions
Minimum
25MHz, Integration Range:
12kHz - 5MHz
10% to 90%
Typical
0.094
ps
0.35
1.2
ns
48
52
%
NOTE: Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when device is
mounted in a test socket with maintained transverse airflow greater than 500 lfpm. Device will meet specifications after thermal equilibrium has
been reached under these conditions.
NOTE: Characterized up to FOUT ≤ 150MHz.
NOTE 1: Measured from the VDD/2 of the input to VDD/2 of the output.
NOTE 2: This parameter is defined in accordance with JEDEC Standard 65.
NOTE 3: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at VDD/2.
NOTE 4: Defined as skew between outputs on different devices operating at the same supply voltage, same temperature, same frequency and
with equal load conditions. Using the same type of inputs on each device, the outputs are measured at VDD/2.
ICS830154AGI-08 REVISION A MARCH 29, 2010
5
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Table 5B. AC Characteristics, VDD = 2.5V ± 5%, TA = -40°C to 85°C
Symbol
Parameter
fOUT
Output Frequency
tpLH
Propagation Delay
(low to high transition); NOTE 1
tpHL
Propagation Delay
(high to low transition); NOTE 1
tPLZ, tPHZ
Test Conditions
Minimum
Maximum
Units
160
MHz
0.8
1.7
ns
0.8
1.7
ns
Disable Time
(active to high-impedance)
10
ns
tPZL, tPZH
Enable Time
(high-impedance to disable)
10
ns
tsk(o)
Output Skew; NOTE 2, 3
250
ps
tsk(pp)
Part-to-Part Skew; NOTE 2, 4
800
ps
tjit
Buffer Additive Phase Jitter, RMS;
refer to Additive Phase Jitter Section
t R / tF
Output Rise/Fall Time
odc
Output Duty Cycle
25MHz, Integration Range:
12kHz - 5MHz
10% to 90%
Typical
0.076
ps
0.35
1.2
ns
48
52
%
NOTE: Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when device is
mounted in a test socket with maintained transverse airflow greater than 500 lfpm. Device will meet specifications after thermal equilibrium has
been reached under these conditions.
NOTE: Characterized up to FOUT ≤ 150MHz.
NOTE 1: Measured from the VDD/2 of the input to VDD/2 of the output.
NOTE 2: This parameter is defined in accordance with JEDEC Standard 65.
NOTE 3: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at VDD/2.
NOTE 4: Defined as skew between outputs on different devices operating at the same supply voltage, same temperature, same frequency and
with equal load conditions. Using the same type of inputs on each device, the outputs are measured at VDD/2.
Table 5C. AC Characteristics, VDD = 1.8V ± 0.15V, TA = -40°C to 85°C
Symbol
Parameter
fOUT
Output Frequency
tpLH
Propagation Delay
(low to high transition); NOTE 1
tpHL
Propagation Delay
(high to low transition); NOTE 1
tPLZ, tPHZ
Test Conditions
Minimum
Maximum
Units
160
MHz
1.1
2.1
ns
1.1
2.1
ns
Disable Time
(active to high-impedance)
10
ns
tPZL, tPZH
Enable Time
(high-impedance to disable)
10
ns
tsk(o)
Output Skew; NOTE 2, 3
250
ps
tsk(pp)
Part-to-Part Skew; NOTE 2, 4
800
ps
tjit
Buffer Additive Phase Jitter, RMS;
refer to Additive Phase Jitter Section
t R / tF
Output Rise/Fall Time
odc
Output Duty Cycle
25MHz, Integration Range:
12kHz - 5MHz
0.63V to 1.17V
Typical
0.193
ps
0.12
0.6
ns
47
53
%
For NOTES, see Table 5B above.
ICS830154AGI-08 REVISION A MARCH 29, 2010
6
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Table 5D. AC Characteristics, VDD = 1.5V ± 0.1V, TA = -40°C to 85°C
Symbol
Parameter
fOUT
Output Frequency
tpLH
Propagation Delay
(low to high transition); NOTE 1
tpHL
Propagation Delay
(high to low transition); NOTE 1
tPLZ, tPHZ
Test Conditions
Minimum
Maximum
Units
160
MHz
1.5
2.7
ns
1.5
2.7
ns
Disable Time
(active to high-impedance)
10
ns
tPZL, tPZH
Enable Time
(high-impedance to disable)
10
ns
tsk(o)
Output Skew; NOTE 2, 3
250
ps
tsk(pp)
Part-to-Part Skew; NOTE 2, 4
800
ps
tjit
Buffer Additive Phase Jitter, RMS;
refer to Additive Phase Jitter Section
t R / tF
Output Rise/Fall Time
odc
Output Duty Cycle
25MHz, Integration Range:
12kHz - 5MHz
0.525V to 0.975V
Typical
0.266
ps
0.12
0.6
ns
47
53
%
NOTE: Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when device is
mounted in a test socket with maintained transverse airflow greater than 500 lfpm. Device will meet specifications after thermal equilibrium has
been reached under these conditions.
NOTE: Characterized up to FOUT ≤ 150MHz.
NOTE 1: Measured from the VDD/2 of the input to VDD/2 of the output.
NOTE 2: This parameter is defined in accordance with JEDEC Standard 65.
NOTE 3: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at VDD/2.
NOTE 4: Defined as skew between outputs on different devices operating at the same supply voltage, same temperature, same frequency and
with equal load conditions. Using the same type of inputs on each device, the outputs are measured at VDD/2.
ICS830154AGI-08 REVISION A MARCH 29, 2010
7
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Additive Phase Jitter (1.5V Output)
The spectral purity in a band at a specific offset from the fundamental
compared to the power of the fundamental is called the dBc Phase
Noise. This value is normally expressed using a Phase noise plot
and is most often the specified plot in many applications. Phase noise
is defined as the ratio of the noise power present in a 1Hz band at a
specified offset from the fundamental frequency to the power value of
the fundamental. This ratio is expressed in decibels (dBm) or a ratio
of the power in the 1Hz band to the power in the fundamental. When
the required offset is specified, the phase noise is called a dBc value,
which simply means dBm at a specified offset from the fundamental.
By investigating jitter in the frequency domain, we get a better
understanding of its effects on the desired application over the entire
time record of the signal. It is mathematically possible to calculate an
expected bit error rate given a phase noise plot.
SSB Phase Noise dBc/Hz
Additive Phase Jitter @ 25MHz
12kHz to 5MHz = 0.266ps (typical)
Offset from Carrier Frequency (Hz)
As with most timing specifications, phase noise measurements has
issues relating to the limitations of the equipment. Often the noise
floor of the equipment is higher than the noise floor of the device. This
is illustrated above. The device meets the noise floor of what is
shown, but can actually be lower. The phase noise is dependent on
the input source and measurement equipment.
ICS830154AGI-08 REVISION A MARCH 29, 2010
The source generator "IFR2042 10kHz – 56.4GHz Low Noise Signal
Generator as external input to an Agilent 8133A 3GHz Pulse
Generator".
8
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Parameter Measurement Information
1.25V±5%
1.65V±5%
SCOPE
VDD
Qx
LVCMOS
SCOPE
VDD
Qx
LVCMOS
GND
GND
-1.25V±5%
-1.65V±5%
3.3V Output Load AC Test Circuit
2.5V Output Load AC Test Circuit
0.9V±0.075V
0.75V±0.05V
SCOPE
VDD
Qx
LVCMOS
SCOPE
VDD
GND
GND
-0.75V±0.05V
-0.9V±0.075V
1.8V Output Load AC Test Circuit
1.5V Output Load AC Test Circuit
Par t 1
V
V
DD
Qx
DD
2
Qx
V
DD
DD
2
tsk(o)
Qy
Output Skew
ICS830154AGI-08 REVISION A MARCH 29, 2010
2
Par t 2
V
Qy
Qx
LVCMOS
2
tsk(pp)
Part-to-Part Skew
9
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Parameter Measurement Information, continued
VDD
OE
(High-level
enabling)
VDD/2
V
VDD/2
V
DD
Q1:Q4
0V
DD
2
2
t PW
t
tEN
tDIS
Output Qx
(See Note)
VOH
VDD/2
odc =
VDD/2
Q1:Q4
x 100%
Output Duty Cycle/Pulse Width/Period
0.525V
0.525V
Q1:Q4
0.63V
0.63V
1.8V Output Rise/Fall Time
VDD
VDD
90%
CLK_IN
2
2
VDD
10%
10%
tR
Q1:Q4
tF
2.5V and 3.3V Output Rise/Fall Time
ICS830154AGI-08 REVISION A MARCH 29, 2010
tF
tR
tF
1.5V Output Rise/Fall Time
90%
1.17V
1.17V
0.975V
tR
Q1:Q4
t PW
t PERIOD
Output Enable/Disable Time
0.975V
PERIOD
2
tpLH
VDD
2
tpHL
Propagation Delay
10
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Applications Information
Recommendations for Unused Output Pins
Outputs:
LVCMOS Outputs
All unused LVCMOS outputs can be left floating. There should be no
trace attached.
ICS830154AGI-08 REVISION A MARCH 29, 2010
11
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Power Considerations
This section provides information on power dissipation and junction temperature for the ICS830154I-08.
Equations and example calculations are also provided.
1.
Power Dissipation.
The total power dissipation for theICS830154I-08 is the sum of the core power plus the power dissipation in the load(s). The following is the
power dissipation for VDD = 3.3V + 5% = 3.465V, which gives worst case results.
Power (core)MAX = VDD_MAX * IDD_MAX = 3.465V *1mA = 3.465mW
Total Static Power:
= Power (core)MAX = 3.465mW
Dynamic Power Dissipation at FOUT_MAX (160MHz)
Total Power (160MHz) = [(CPD * N) * Frequency * (VDDO)2] = [(14pF *4) * 160MHz * (3.465V)2] = 107.6mW
N = number of outputs
Total Power
= Static Power + Dynamic Power Dissipation
= 3.465mW + 107.6mW
= 111.065mW
2. Junction Temperature.
Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad, and directly affects the reliability of the device. The
maximum recommended junction temperature is 125°C. Limiting the internal transistor junction temperature, Tj, to 125°C ensures that the bond
wire and bond pad temperature remains below 125°C.
The equation for Tj is as follows: Tj = θJA * Pd_total + TA
Tj = Junction Temperature
θJA = Junction-to-Ambient Thermal Resistance
Pd_total = Total Device Power Dissipation (example calculation is in section 1 above)
TA = Ambient Temperature
In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance θJA must be used. Assuming no air flow and
a multi-layer board, the appropriate value is 121.5°C/W per Table 6A below.
Therefore, Tj for an ambient temperature of 85°C with all outputs switching is:
85°C + 0.111W *121.5°C/W = 98.5°C. This is below the limit of 125°C.
This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow and the type of
board (multi-layer).
Table 6A. Thermal Resistance θJA for 8 Lead TSSOP, Forced Convection
θJA by Velocity
Meters per Second
Multi-Layer PCB, JEDEC Standard Test Boards
0
1
2.5
121.5°C/W
117.3°C/W
115.3°C/W
0
1
2.5
103°C/W
94°C/W
89°C/W
Table 6B. Thermal Resistance θJA for 8 Lead SOIC, Forced Convection
θJA by Velocity
Meters per Second
Multi-Layer PCB, JEDEC Standard Test Boards
ICS830154AGI-08 REVISION A MARCH 29, 2010
12
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Reliability Information
Table 7A. θJA vs. Air Flow Table for a 8 Lead TSSOP
θJA vs. Air Flow
Meter per Second
Multi-Layer PCB, JEDEC Standard Test Boards
0
1
2.5
121.5°C/W
117.3°C/W
115.3°C/W
0
1
2.5
103°C/W
94°C/W
89°C/W
Table 7B. θJA vs. Air Flow Table for a 8 Lead SOIC
θJA vs. Air Flow
Meter per Second
Multi-Layer PCB, JEDEC Standard Test Boards
Transistor Count
The transistor count for ICS830154I-08 is: 191
ICS830154AGI-08 REVISION A MARCH 29, 2010
13
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Package Outline and Package Dimensions
Package Outline - G Suffix for 8 Lead TSSOP
Package Outline - M Suffix for 8 Lead SOIC
Table 8B. Package Dimensions
Table 8A. Package Dimensions for 8Lead TSSOP
All Dimensions in Millimeters
Symbol
Minimum
Maximum
N
8
A
1.35
1.75
A1
0.10
0.25
B
0.33
0.51
C
0.19
0.25
D
4.80
5.00
E
3.80
4.00
e
1.27 Basic
H
5.80
6.20
h
0.25
0.50
L
0.40
1.27
α
0°
8°
All Dimensions in Millimeters
Symbol
Minimum
Maximum
N
8
A
1.20
A1
0.5
0.15
A2
0.80
1.05
b
0.19
0.30
c
0.09
0.20
D
2.90
3.10
E
6.40 Basic
E1
4.30
4.50
e
0.65 Basic
L
0.45
0.75
α
0°
8°
aaa
0.10
Reference Document: JEDEC Publication 95, MS-012
Reference Document: JEDEC Publication 95, MO-153
ICS830154AGI-08 REVISION A MARCH 29, 2010
14
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Ordering Information
Table 9. Ordering Information
Part/Order Number
830154AGI-08LF
830154AGI-08LFT
830154AMI-08LF
830154AMI-08LFT
Marking
AI08L
AI08L
154AI08L
154AI08L
Package
Lead-Free, 8 Lead TSSOP
Lead-Free, 8 Lead TSSOP
Lead-Free, 8 Lead SOIC
Lead-Free, 8 Lead SOIC
Shipping Packaging
Tube
2500 Tape & Reel
Tube
2500 Tape & Reel
Temperature
-40°C to 85°C
-40°C to 85°C
-40°C to 85°C
-40°C to 85°C
NOTE: Parts that are ordered with an "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.
While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the
infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal
commercial and industrial applications. Any other applications, such as those requiring high reliability or other extraordinary environmental requirements are not recommended without
additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support
devices or critical medical instruments.
ICS830154AGI-08 REVISION A MARCH 29, 2010
15
©2010 Integrated Device Technology, Inc.
ICS830154I-08 Data Sheet
6024 Silver Creek Valley Road
San Jose, California 95138
OVER-VOLTAGE TOLERANT 1.5V, 1:4 FANOUT BUFFER
Sales
800-345-7015 (inside USA)
+408-284-8200 (outside USA)
Fax: 408-284-2775
www.IDT.com/go/contactIDT
Technical Support
[email protected]
+480-763-2056
DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document,
including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not
guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the
suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any
license under intellectual property rights of IDT or any third parties.
IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT
product in such a manner does so at their own risk, absent an express, written agreement by IDT.
Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third
party owners.
Copyright 2010. All rights reserved.