SiHJ8N60E www.vishay.com Vishay Siliconix E Series Power MOSFET FEATURES PRODUCT SUMMARY VDS (V) at TJ max. RDS(on) typ. at 25 °C (Ω) • Low figure-of-merit (FOM) Ron x Qg 650 VGS = 10 V • Low input capacitance (Ciss) 0.45 Qg max. (nC) 44 • Reduced switching and conduction losses Qgs (nC) 5 • Ultra low gate charge (Qg) Qgd (nC) 10 • Avalanche energy rated (UIS) Configuration Single • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 D PowerPAK® SO-8L Single APPLICATIONS • Switch mode power supplies (SMPS) • Flyback converter • Lighting - High-intensity discharge (HID) - Fluorescent ballast lighting • Consumer - Wall adaptors G S N-Channel MOSFET ORDERING INFORMATION Package PowerPAK SO-8L Lead (Pb)-free and Halogen-free SiHJ8N60E-T1-GE3 ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted) PARAMETER SYMBOL LIMIT Drain-Source Voltage VDS 600 Gate-Source Voltage VGS ± 30 Continuous Drain Current (TJ = 150 °C) VGS at 10 V TC = 25 °C TC = 100 °C Pulsed Drain Current a UNIT V 8 ID A 5 IDM 18 Linear Derating Factor 0.71 W/°C Single Pulse Avalanche Energy b EAS 88 mJ Maximum Power Dissipation PD 89 W TJ, Tstg -55 to +150 °C Operating Junction and Storage Temperature Range Drain-Source Voltage Slope TJ = 125 °C Reverse Diode dV/dt d 70 dV/dt V/ns 17 Notes a. Repetitive rating; pulse width limited by maximum junction temperature. b. VDD = 50 V, starting TJ = 25 °C, L = 28.2 mH, Rg = 25 Ω, IAS = 2.5 A. c. ISD ≤ ID, dI/dt = 100 A/μs, starting TJ = 25 °C. THERMAL RESISTANCE RATINGS PARAMETER SYMBOL TYP. Maximum Junction-to-Ambient RthJA 52 65 Maximum Junction-to-Case (Drain) RthJC 1 1.4 S15-2485-Rev. A, 19-Oct-15 MAX. UNIT °C/W Document Number: 91563 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHJ8N60E www.vishay.com Vishay Siliconix SPECIFICATIONS (TJ = 25 °C, unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Static Drain-Source Breakdown Voltage VDS Temperature Coefficient Gate-Source Threshold Voltage (N) Gate-Source Leakage Zero Gate Voltage Drain Current Drain-Source On-State Resistance Forward Transconductance VDS VGS = 0 V, ID = 250 μA 600 - - V ΔVDS/TJ Reference to 25 °C, ID = 1 mA - 0.71 - V/°C VGS(th) VDS = VGS, ID = 250 μA 2 - 4 V VGS = ± 20 V - - ± 100 nA μA IGSS IDSS RDS(on) VGS = ± 30 V - - ±1 VDS = 600 V, VGS = 0 V - - 1 VDS = 480 V, VGS = 0 V, TJ = 125 °C - - 10 - 0.45 0.52 Ω - S VGS = 10 V ID = 4 A gfs VDS = 30 V, ID = 4 A - 2.4 Input Capacitance Ciss 754 - Coss - 46 - Reverse Transfer Capacitance Crss VGS = 0 V, VDS = 100 V, f = 1 MHz - Output Capacitance - 5 - Effective Output Capacitance, Energy Related a Co(er) - 40 - Effective Output Capacitance, Time Related b Co(tr) - 130 - - 22 44 - 5 - - 10 - μA Dynamic pF VDS = 0 V to 480 V, VGS = 0 V Total Gate Charge Qg Gate-Source Charge Qgs Gate-Drain Charge Qgd Turn-On Delay Time td(on) - 14 28 tr VDD = 480 V, ID = 4 A, VGS = 10 V, Rg = 9.1 Ω - 15 30 - 29 58 - 14 28 f = 1 MHz, open drain 0.5 0.93 2.0 - - 8 - - 18 - 0.85 1.2 V - 258 516 ns - 2.4 4.8 μC - 16 - A Rise Time Turn-Off Delay Time td(off) Fall Time tf Gate Input Resistance Rg VGS = 10 V ID = 4 A, VDS = 480 V nC ns Ω Drain-Source Body Diode Characteristics Continuous Source-Drain Diode Current IS Pulsed Diode Forward Current ISM Diode Forward Voltage VSD Reverse Recovery Time trr Reverse Recovery Charge Qrr Reverse Recovery Current IRRM MOSFET symbol showing the integral reverse p - n junction diode D A G TJ = 25 °C, IS = 4 A, VGS = 0 V TJ = 25 °C, IF = IS = 4 A, dI/dt = 100 A/μs, VR = 25 V S Notes a. Coss(er) is a fixed capacitance that gives the same energy as Coss while VDS is rising from 0 % to 80 % VDSS. b. Coss(tr) is a fixed capacitance that gives the same charging time as Coss while VDS is rising from 0 % to 80 % VDSS. S15-2485-Rev. A, 19-Oct-15 Document Number: 91563 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHJ8N60E www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 3.0 20 15 V 14 V 13 V 12 V 11 V 10 V 9V 8V 7V 6V BOTTOM 5 V 16 12 ID = 4 A TJ = 25 °C RDS(on), Drain-to-Source On-Resistance (Normalized) 8 4 0 5 10 15 20 25 VDS, Drain-to-Source Voltage (V) 1.5 1.0 VGS = 10 V 0.5 -60 -40 -20 30 40 60 80 100 120 140 160 10 000 TOP 15 V 14 V 13 V 12 V 11 V 10 V 9V 8V 7V 6V BOTTOM 5 V TJ = 150 °C 6 100 Coss 10 Crss 3 0 VGS = 0 V, f = 1 MHz Ciss = Cgs + Cgd, Cds shorted Crss = Cgd Coss = Cds + Cgd Ciss 1000 C, Capacitance (pF) 9 20 Fig. 4 - Normalized On-Resistance vs. Temperature 15 12 0 TJ, Junction Temperature (°C) Fig. 1 - Typical Output Characteristics ID, Drain-to-Source Current (A) 2.0 0 0 1 0 5 10 15 20 25 VDS, Drain-to-Source Voltage (V) 30 0 100 200 300 400 500 VDS, Drain-to-Source Voltage (V) 600 Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage Fig. 2 - Typical Output Characteristics 20 10 000 6 5 16 TJ = 25 °C 12 1000 4 Coss (pF) ID, Drain-to-Source Current (A) 2.5 TJ = 150 °C 8 Eoss Coss 3 100 4 2 1 VDS = 30.8 V 10 0 0 5 10 15 20 VGS, Gate-to-Source Voltage (V) Fig. 3 - Typical Transfer Characteristics S15-2485-Rev. A, 19-Oct-15 Eoss (μJ) ID, Drain-to-Source Current (A) TOP 25 0 0 100 200 300 VDS 400 500 600 Fig. 6 - Coss and Eoss vs. VDS Document Number: 91563 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHJ8N60E www.vishay.com Vishay Siliconix 10 VDS = 480 V VDS = 300 V VDS = 120 V 20 8 ID, Drain Current (A) VGS, Gate-to-Source Voltage (V) 24 16 12 8 6 4 2 4 0 0 0 10 20 30 Qg, Total Gate Charge (nC) 25 40 Fig. 7 - Typical Gate Charge vs. Gate-to-Source Voltage 50 75 100 125 TC, Case Temperature (°C) 150 Fig. 10 - Maximum Drain Current vs. Case Temperature VDS, Drain-to-Source Breakdown Voltage (V) 750 ISD, Reverse Drain Current (A) 10 TJ = 150 °C TJ = 25 °C 1 VGS = 0 V 0.1 0.2 0.4 0.6 0.8 1.0 VSD, Source-Drain Voltage (V) 1.2 1.4 725 700 675 650 625 600 ID = 250 μA 575 -60 -40 -20 0 20 40 60 80 100 120 140 160 TJ, Junction Temperature (°C) Fig. 8 - Typical Source-Drain Diode Forward Voltage Fig. 11 - Temperature vs. Drain-to-Source Voltage 100 Operation in this Area Limited by RDS(on) IDM Limited ID, Drain Current (A) 10 100 μs 1 Limited by RDS(on)* 1 ms 0.1 TC = 25 °C TJ = 150 °C Single Pulse 10 ms BVDSS Limited 0.01 1 10 100 1000 VDS, Drain-to-Source Voltage (V) * VGS > minimum VGS at which RDS(on) is specified Fig. 9 - Maximum Safe Operating Area S15-2485-Rev. A, 19-Oct-15 Document Number: 91563 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHJ8N60E www.vishay.com Vishay Siliconix Normalized Effective Transient Thermal Impedance 1 Duty Cycle = 0.5 0.2 0.1 0.1 0.05 0.02 Single Pulse 0.01 0.00001 0.000001 0.0001 0.001 0.01 1 0.1 Pulse Time (s) Fig. 12 - Normalized Thermal Transient Impedance, Junction-to-Case Normalized Effective Transient Thermal Impedance 1 Duty Cycle = 0.5 0.1 0.2 0.1 0.05 0.01 0.02 0.001 Single Pulse 0.0001 0.0001 0.001 0.01 0.1 1 100 10 1000 Pulse Time (s) Fig. 13 - Normalized Thermal Transient Impedance, Junction-to-Ambient VDS VGS RG RD VDS 90 % D.U.T. + - VDD 10 V Pulse width ≤ 1 µs Duty factor ≤ 0.1 % Fig. 14 - Switching Time Test Circuit S15-2485-Rev. A, 19-Oct-15 10 % VGS td(on) tr td(off) tf Fig. 15 - Switching Time Waveforms Document Number: 91563 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHJ8N60E www.vishay.com Vishay Siliconix L Vary tp to obtain required IAS VDS QG 10 V D.U.T RG + - IAS QGS QGD V DD VG 10 V 0.01 Ω tp Charge Fig. 16 - Unclamped Inductive Test Circuit Fig. 18 - Basic Gate Charge Waveform Current regulator Same type as D.U.T. VDS tp VDD 50 kΩ 12 V 0.2 µF 0.3 µF VDS + D.U.T. IAS Fig. 17 - Unclamped Inductive Waveforms - VDS VGS 3 mA IG ID Current sampling resistors Fig. 19 - Gate Charge Test Circuit S15-2485-Rev. A, 19-Oct-15 Document Number: 91563 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHJ8N60E www.vishay.com Vishay Siliconix Peak Diode Recovery dV/dt Test Circuit + D.U.T. Circuit layout considerations • Low stray inductance • Ground plane • Low leakage inductance current transformer + - - Rg • • • • + dV/dt controlled by Rg Driver same type as D.U.T. ISD controlled by duty factor “D” D.U.T. - device under test + - VDD Driver gate drive P.W. Period D= P.W. Period VGS = 10 Va D.U.T. lSD waveform Reverse recovery current Body diode forward current dI/dt D.U.T. VDS waveform Diode recovery dV/dt Re-applied voltage Inductor current VDD Body diode forward drop Ripple ≤ 5 % ISD Note a. VGS = 5 V for logic level devices Fig. 20 - For N-Channel Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?91563. S15-2485-Rev. A, 19-Oct-15 Document Number: 91563 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information www.vishay.com Vishay Siliconix PowerPAK® SO-8L Case Outline for Non-Al Parts W E1 E E2 W2 W3 W1 b2 D2 b b1 L L1 L1 A1 e θ D1 D b3 b4 0.25 gauge line Topside view Backside view (single) E2 W2 C A W3 W1 F K D3 D3 D2 b3 b4 Backside view (dual) Revision: 16-May-16 Document Number: 69003 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information www.vishay.com DIM. Vishay Siliconix MILLIMETERS INCHES MIN. NOM. MAX. MIN. NOM. MAX. A 1.00 1.07 1.14 0.039 0.042 0.045 A1 0.00 - 0.127 0.00 - 0.005 b 0.33 0.41 0.48 0.013 0.016 0.019 b1 0.44 0.51 0.58 0.017 0.020 0.023 b2 4.80 4.90 5.00 0.189 0.193 0.197 b3 0.094 b4 0.004 0.47 0.019 c 0.20 0.25 0.30 0.008 0.010 0.012 D 5.00 5.13 5.25 0.197 0.202 0.207 D1 4.80 4.90 5.00 0.189 0.193 0.197 D2 3.86 3.96 4.06 0.152 0.156 0.160 D3 1.63 1.73 1.83 0.064 0.068 0.072 e 1.27 BSC 0.050 BSC E 6.05 6.15 6.25 0.238 0.242 0.246 E1 4.27 4.37 4.47 0.168 0.172 0.176 E2 3.18 3.28 3.38 0.125 0.129 0.133 F - - 0.15 - - 0.006 L 0.62 0.72 0.82 0.024 0.028 0.032 L1 0.92 1.07 1.22 0.036 0.042 0.048 K 0.51 0.020 W 0.23 0.009 W1 0.41 0.016 W2 2.82 0.111 W3 2.96 0.117 0° - 10° 0° - 10° ECN: T16-0221-Rev. D, 16-May-16 DWG: 5976 Note • Millimeters will gover Revision: 16-May-16 Document Number: 69003 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PAD Pattern www.vishay.com Vishay Siliconix RECOMMENDED MINIMUM PAD FOR PowerPAK® SO-8L SINGLE 5.000 (0.197) 0.510 (0.020) 2.310 (0.091) 4.061 (0.160) 0.595 (0.023) 6.250 (0.246) 8.250 (0.325) 3.630 (0.143) 0.610 (0.024) 0.410 (0.016) 2.715 (0.107) 0.860 (0.034) 1.291 (0.051) 0.710 (0.028) 0.820 (0.032) 1.905 (0.075) 1.270 (0.050) 7.250 (0.285) Recommended Minimum Pads Dimensions in mm (inches) Revision: 07-Feb-12 1 Document Number: 63818 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000