DATASHEET

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
Updated boilerplate and made editorial changes throughout. - LTG
00-05-19
Monica L. Poelking
B
Update boilerplate to MIL-PRF-38535 requirements. - CFS
05-07-25
Thomas M. Hess
C
Update boilerplate paragraphs to MIL-PRF-38535 requirements. - jwc
15-05-22
Thomas M. Hess
REV
SHEET
REV
SHEET
REV STATUS
REV
C
C
C
C
C
C
C
C
C
C
C
C
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
PMIC N/A
PREPARED BY
DDLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
Ray Monnin
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
D. A. DiCenzo
APPROVED BY
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
MICROCIRCUIT, CMOS, OCTAL BUS
TRANSCEIVER, MONOLITHIC SILICON
N. A. Hauck
DRAWING APPROVAL DATE
87-04-21
AMSC N/A
REVISION LEVEL
C
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
5962-87577
1 OF 12
5962-E314-15
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-87577
01
R
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
Generic number
01
02
Circuit function
82C86
82C87
CMOS octal bus transceiver
CMOS octal inverting bus transceiver
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
R
2
Descriptive designator
Terminals
GDIP1-T20 or CDIP2-T20
CQCC1-N20
Package style
20
20
Dual-in-line
Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Supply voltage range (referenced to ground) ................................
Input, output or I/O voltage applied ................................................
Storage temperature range............................................................
Maximum power dissipation, (PD) ..................................................
Lead temperature (soldering, 10 seconds) ....................................
Maximum junction temperature (TJ) ...............................................
Thermal resistance, junction-to-case (θJC):
Case R ...................................................................................
Case 2 ....................................................................................
+8.0 V dc maximum
GND -0.5 V dc to VCC +0.5 V dc
-65°C to +150°C
1.0 W 1/
+275°C
+150°C
(See MIL-STD-1835)
23°C/W 2/
________
1/ Must withstand the added PD due to short circuit test (e.g., IOS).
2/ When a thermal resistance value for this case is included in MIL-STD-1835 that value shall supersede the value indicated
herein.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
2
1.4 Recommended operating conditions.
Supply voltage (VCC) ......................................................................
Input to output delay, inverting or noninverting (tIVOV) ....................
Transmit/receive hold time (tEHTV) ..................................................
Transmit/receive setup time (tTVEL) ................................................
Output disable time (tEHOZ) .............................................................
Output enable time (tELOV)..............................................................
Input rise/fall time (tr/tf) ...................................................................
Minimum output enable high time (tEHEL) .......................................
Case operating temperature range (TC) .........................................
+4.5 V dc minimum to +5.5 V dc maximum
5 ns minimum 3/ 4/ 5/ (reference no. 1)
5 ns minimum 3/ 4/ (reference no. 2)
10 ns minimum 3/ 4/ (reference no. 3)
5 ns minimum to 35 ns maximum 3/ 4/ (reference no. 4)
10 ns minimum 3/ 4/ 5/ (reference no. 5)
20 ns minimum 3/ 4/ (reference no. 6)
35 ns minimum 3/ 4/ 6/ (reference no. 7)
-55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535
-
Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883
MIL-STD-1835
-
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103
MIL-HDBK-780
-
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
________
3/
4/
5/
6/
Not tested but characterized at initial device design and after major process or design changes affecting this parameter.
See appropriate ac test load and timing reference number see figure 4.
Reference table I for other limit.
A system limitation only when changing directions.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
4
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.4 Block diagram. The block diagram shall be as specified on figure 3.
3.2.5 Test circuit and timing waveforms. The test circuit and timing waveforms shall be as specified on figure 4.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and
Maritime-VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requirements of MIL-PRF-38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DLA Land and Maritime-VA shall be required for any change that
affects this drawing.
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
4
TABLE I. Electrical performance characteristics.
Test
Symbol
Output high
voltage
VOH
Output low voltage
VOL
Conditions
-55°C ≤ TC ≤ +125°C
unless otherwise specified
Group A
subgroup
s
VCC = 4.5 V, IOH = -8.0 mA
B outputs 1/
1, 2, 3
Device
type
Limits
Min
3.0
All
VCC = 4.5 V, IOH = -4.0 mA
A outputs 1/
3.0
VCC = 4.5 V, IOH = -100 µA
A or B outputs 1/
VCC
-0.4
VCC = 4.5 V, IOL = 20 mA
B outputs 1/
1, 2, 3
All
1, 2, 3
All
Unit
Max
V
0.45
V
VCC = 4.5 V, IOL = 12 mA
A outputs 1/
Input high level
VIH
VCC = 5.5 V
Input low level
VIL
VCC = 4.5 V
1, 2, 3
All
0.8
V
Input leakage
current
Output leakage
current
IIN
VCC = 5.5 V, VIN = VCC or GND
1, 2, 3
All
-10.0
10.0
µA
IOUT
VCC = 5.5 V, VOUT = VCC or GND,
1, 2, 3
All
-10.0
10.0
µA
Standby supply
current
ICCSB
VCC = 5.5 V, VIN = VCC or GND,
outputs open
1, 2, 3
All
10
µA
Input capacitance,
A inputs
CIN
f = 1.0 MHz, TC = +25°C
All measurements referenced to
device ground. See 4.3.1c
4
All
Case R
13
pF
All
Case 2
10
f = 1.0 MHz, TC = +25°C
All measurements referenced to
device ground. See 4.3.1c
4
All
Case R
17
All
Case 2
15
f = 1.0 MHz, TC = +25°C
All measurements referenced to
device ground. See 4.3.1c
4
All
Case R
12
All
Case 2
7
VCC = 4.5 V and 5.5 V 3/
See 4.3.1d
7, 8
Input capacitance,
B inputs
Input capacitance,
all other inputs
2/
2.2
V
OE ≥ VCC –0.5 V
CIN
CIN
Functional test
pF
pF
All
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
7
TABLE I. Electrical performance characteristics. - Continued
Test
Symbol
Conditions
-55°C ≤ TC ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits
Unit
Input to output delay,
inverting or noninverting
tIVOV
VCC = 4.5 V and 5.5 V 3/
Reference number 1 and
figure 4.
9, 10, 11
All
Min
4/
Max
35
ns
Output enable time
tELOV
VCC = 4.5 V and 5.5 V 3/
Reference number 5 and
figure 4
9, 10, 11
All
4/
65
ns
1/ Interchanging of force and sense conditions is permitted.
2/ VIH is measured by applying a pulse magnitude = VIH minimum to one data input at a time and checking the corresponding
device output for a valid logical one during valid input high time. Control pins, T (transmit) and OE, are tested separately
with all device data input pins at VCC –0.4 V.
3/ Tested as follows: f = 1 MHz, VIH = 2.6 V, VIL = 0.4 V, CL = 50 pF (unless otherwise specified), VOH ≥ 1.5 V, VOL ≤ 1.5 V, and
VIH for T (transmit control pin) ≥ VCC –0.5 V. Input rise and fall times are driven at 1 ns/V.
4/ Reference 1.4 for this limit.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
7
Device type
01
Case outlines
R and 2
Terminal Number
Terminal Symbol
Terminal Number
Terminal Symbol
1
2
3
4
5
6
7
8
9
10
A0
A1
A2
A3
A4
A5
A6
A7
OE
GND
11
12
13
14
15
16
17
18
19
20
T
B7
B6
B5
B4
B3
B2
B1
B0
VCC
Device type
02
Case outlines
R and 2
Terminal Number
Terminal Symbol
Terminal Number
Terminal Symbol
1
2
3
4
5
6
7
8
9
10
A0
A1
A2
A3
A4
A5
A6
A7
OE
GND
11
12
13
14
15
16
17
18
19
20
T
B7
B6
B5
B4
B3
B2
B1
B0
VCC
FIGURE 1. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
7
T
OE
A
B
X
H
Z
Z
H
L
I
O
L
L
O
I
H = Logic one
L = Logic zero
I = Input mode
O = Output mode
X = Irrelevant
Z = High impedance
FIGURE 2. Truth table.
FIGURE 3. Bock diagram.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
12
NOTE: Includes jig and stray capacitance. Resistances have a tolerance of ±1%. Capacitances have a tolerance of ±10%.
FIGURE 4. Test circuit and timing waveforms.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
12
All timing measurements are made at 1.5 V unless otherwise noted.
Inputs must switch between VIL –0.4 V and VIH +0.4 V.
FIGURE 4. Test circuit and timing waveforms – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
12
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements
Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004)
-----
Final electrical test parameters
(method 5004)
1*, 2, 3, 7, 8, 9, 10, 11
Group A test requirements
(method 5005)
1, 2, 3, 7, 8, 9, 10, 11
Groups C and D end-point
electrical parameters
(method 5005)
2, 8 (125°C only), 10
* PDA applies to subgroup 1.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of
MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a.
Tests shall be as specified in table II herein.
b.
Subgroups 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.
c.
Subgroup 4 (CIN measurement) shall be measured only for the initial test and after process or design changes which
may affect input capacitance.
d.
Subgroups 7 and 8 shall include verification of the truth table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
12
4.3.2 Groups C and D inspections.
a.
End-point electrical parameters shall be as specified in table II herein.
b.
Steady-state life test conditions, method 1005 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1005 of MIL-STD-883.
(2)
TA = +125°C, minimum.
(3)
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a
contractor-prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD. DLA Land and Maritime will maintain a record of users and this list will be used
for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962)
should contact DLA Land and Maritime-VA, telephone (614) 692-8108.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 432183990, or telephone
(614) 692-0547.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MILHDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by
DLA Land and Maritime-VA.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-87577
A
REVISION LEVEL
C
SHEET
12
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 15-05-22
Approved sources of supply for SMD 5962-87577 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and/or QML-38535 during the next revision. MIL-HDBK-103 and/or QML-38535 will
be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information
bulletin is superseded by the next dated revision of MIL-HDBK-103 and/or QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8757701RA
34371
MD82C86H-5/883
5962-87577012A
3/
MR82C86H-5/883
5962-8757702RA
34371
MD82C87H-5/883
5962-87577022A
3/
MR82C87H-5/883
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE
number
34371
Vendor name
and address
Intersil Corporation
1001 Murphy Ranch Road
Milpitas, CA 95035-6803
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.