REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add paragraph 3.1.1 and Appendix A for microcircuit die. Changes in accordance with N.O.R. 5962-R014-98. 97-12-21 Raymond Monnin B Make changes to boilerplate and add device class T. - ro 98-12-03 Raymond Monnin C Update drawing to current requirements. Delete paragraphs 4.4.4.2 and 4.4.4.3. Editorial changes throughout. – drw 06-08-15 Raymond Monnin D Add device type 04. Delete paragraph 4.4.4.2 dose rate burnout and Table III Irradiation test connections. - ro 13-05-01 C. Saffle E Add device type 04 to footnotes 1/ and 4/ as specified under Table I. - ro 14-11-18 C. Saffle REV SHEET REV E E E E SHEET 15 16 17 18 REV STATUS REV E E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Sandra Rooney STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil CHECKED BY Sandra Rooney APPROVED BY Michael A. Frye DRAWING APPROVAL DATE 95-11-14 REVISION LEVEL E MICROCIRCUIT, LINEAR RADIATION HARDENED CMOS, DUAL, DPST ANALOG SWITCHES, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 5962-95812 1 OF 18 5962-E508-14 1. SCOPE 1.1 Scope. This drawing documents three product assurance class levels consisting of high reliability (device class Q), space application (device class V) and for appropriate satellite and similar applications (device class T). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. For device class T, the user is encouraged to review the manufacturer’s Quality Management (QM) plan as part of their evaluation of these parts and their acceptability in the intended application. 1.2 PIN. The PIN is as shown in the following example: 5962 R Federal stock class designator \ 95812 RHA designator (see 1.2.1) 01 V C C Device type (see 1.2.2) Device class designator (see 1.2.3) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number 1.2.1 RHA designator. Device classes Q, T and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 02 03 04 Circuit function HS302RH HS306RH HS384RH HS302EH Radiation hardened DI, dual DPST CMOS switch Radiation hardened DI, dual DPST CMOS switch Radiation hardened DI, dual DPST CMOS switch Radiation hardened DI, dual DPST CMOS switch 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation Q, V Certification and qualification to MIL-PRF-38535 T Certification and qualification to MIL-PRF-38535 with performance as specified in the device manufacturers approved quality management plan. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter C E X Y Descriptive designator CDIP2-T14 CDIP2-T16 CDFP3-F14 CDFP4-F16 Terminals Package style 14 16 14 16 Dual-in-line Dual-in-line Flat package Flat package 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q, T, and V. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 2 1.3 Absolute maximum ratings. 1/ Supply voltage between +V and -V .............................................................................. Supply voltage between +V and ground ....................................................................... Supply voltage between -V and ground ....................................................................... Digital input overvoltage : +VA ........................................................................................................................... 44 V 22 V 22 V +VSUPPLY + 4 V -VA ............................................................................................................................ -VSUPPLY - 4 V Analog input overvoltage : +VS ........................................................................................................................... +VSUPPLY + 1.5 V -VS ............................................................................................................................ -VSUPPLY - 1.5 V Continuous current, S or D ........................................................................................... 10 mA Peak current, S or D (pulsed at 1 ms, 10 percent duty cycle max) .......................................................... 40 mA Storage temperature range .......................................................................................... -65C to +150C Maximum package power dissipation at 125C (PD) 2/: Case outlines C and E .............................................................................................. 0.71 W Case outlines X and Y .............................................................................................. 0.48 W Thermal resistance, junction-to-case (JC): Case outlines C and E .............................................................................................. 19C/W Case outlines X and Y .............................................................................................. 17C/W Thermal resistance, junction-to-ambient (JA): Case outlines C and E .............................................................................................. 70C/W Case outlines X and Y .............................................................................................. 105C/W Lead temperature (soldering, 10 seconds) ................................................................... +300C Junction temperature (TJ) ............................................................................................ +175C 1.4 Recommended operating conditions. Operating supply voltage (VSUPPLY) ......................................................................... 15 V Ambient operating temperature range (TA) .................................................................. -55C to +125C 1.5 Radiation features Maximum total dose available (dose rate = 50 – 300 rads(Si)/s) : Device types 01, 02, and 03 ...................................................................................... 100 krads(Si) 3/ Device type 04 .......................................................................................................... 100 krads(Si) 4/ Maximum total dose available (dose rate .010 rad(Si)/s): Device type 04 .......................................................................................................... 50 krads(Si) 4/ Latch up immune........................................................................................................... No latch up 5/ ______ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ If device power exceeds package dissipation capacity, provide heat sink or derate linearly (the derating is based on JA) at the following rates: Case outlines C and E ................................................................................................. 14.3 mW/C Case outlines X and Y ................................................................................................... 9.5 mW/C 3/ Device types 01, 02, and 03 may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. However, radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. 4/ Device type 04 radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A to a maximum total dose of 100 krads(Si) and condition D to a maximum total dose of 50 krads(Si). Lot acceptance testing is performed in accordance with MIL-PRF-38535, Appendix B, technology conformance inspection (TCI) group E, subgroup 2. 5/ Devices use dielectrically isolated (DI) technology and latch up is physically not possible. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q, T and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 3.1.1 Microcircuit die. For the requirements of microcircuit die, see appendix A to this document. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q, T and V. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type 1 All Limits Min “Switch on” resistance +RDS VD = 10 V, IS = -10 mA S1/S2/S3/S4 M,D,P,L,R 2/ -RDS VD = -10 V, IS = 10 mA S1/S2/S3/S4 M,D,P,L,R 2/ Leakage current into the +IS(OFF) S1/S2/S3/S4 source terminal of an M,D,P,L,R 2/ “OFF” switch -IS(OFF) VS = -14 V, VD = +14 V S1/S2/S3/S4 M,D,P,L,R 2/ Leakage current into the +ID(OFF) S1/S2/S3/S4 drain terminal of an M,D,P,L,R 2/ “OFF” switch -ID(OFF) VD = +14 V, VS = -14 V S1/S2/S3/S4 M,D,P,L,R 2/ Leakage current from an +ID(ON) M,D,P,L,R 2/ switch (Drain and -ID(ON) Source) VD = VS = -14 V S1/S2/S3/S4 M,D,P,L,R 2/ Low level input address IAL All channels VA = 0.8 V M,D,P,L,R 2/ current All channels VA = 3.5 V M,D,P,L,R 2/ High level input address IAH 1 50 2, 3 75 1 60 All -2 +2 2, 3 -100 +100 1 -100 +100 1 -2 +2 2, 3 -100 +100 1 -100 +100 -2 +2 2, 3 -100 +100 1 -100 +100 1 -2 +2 2, 3 -100 +100 1 -100 +100 -2 +2 2, 3 -100 +100 1 -100 +100 All All 1 -2 +2 2, 3 -100 +100 1 -100 +100 1, 2, 3 01, 03, -1 +1 1 04 -1 +1 1, 2, 3 02 -1 +1 -1 +1 01, 03, -1 +1 1 04 -1 +1 1, 2, 3 02 -1 +1 -1 +1 1 1, 2, 3 All channels VA = 4.0 V M,D,P,L,R 2/ current 60 1 VD = VS = +14 V S1/S2/S3/S4 “ON” driver into the 75 1 1 VD = -14 V, VS = +14 V All channels VA = 11 V M,D,P,L,R 2/ Max 50 2, 3 1 VS = +14 V, VD = -14 V Unit 1 nA nA nA A A See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 5 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type 1 01, 03, Max 10 2, 3 04 100 Limits Min Positive supply current +I All channels VA = 0.8 V M,D,P,L,R 2/ Unit 1 100 VA1 = 0 V, VA2 = 4.0 V 1 0.5 VA1 = 4.0 V, VA2 = 0 V 2, 3 1 1 1 M,D,P,L,R 2/ 1 All channels VA = 0 V, 15 V M,D,L,R 2/, All channels 02 A mA A 10 2, 3 100 1 100 1 100 VA = 0 V M,D,L,R 2/, All channels VA = 15 V Negative supply current -I All channels VA = 0.8 V M,D,P,L,R 2/ -10 2, 3 04 -100 -10 VA1 = 0 V, VA2 = 4.0 V 1 -10 VA1 = 4.0 V, VA2 = 0 V 2, 3 -100 1 -100 1 All channels VA = 0 V, 15 V CIS(OFF) 01, 03, 1 M,D,P,L,R 2/ Switch input capacitance 1 02 A -10 2, 3 -100 M,D,P,L,R 2/ 1 -100 Measured Source to 3/, 4/ 4 All 28 pF 4 All 10 pF GND Driver input capacitance Switch output CC1 VA = 0 V 3/ 4/ CC2 VA = 15 V 3/ 4/ COS Measured Drain to 3/, 4/ 10 4 All 28 pF 4 All 40 dB 4 All 40 dB 4 All GND Off isolation VISO Cross talk VCR VGEN = 1 VPP, 3/, 4/ f = 1 MHz VGEN = 1 VPP, 3/, 4/ f = 1 MHz Charge transfer error VCTE VS = GND, 3/, 4/ 15 mV CL = 0.01 F See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 6 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type RL = 300 , VS = +3 V 9 01, 03, Max 300 VAH = 4.0 V, VAL = 0 V, 10, 11 04 500 02 300 Limits Min Switch turn “ON” time tON Unit ns see figure 3 M,D,P,L,R 2/ 9 500 9 RL = 300 , VS = +3 V VAH = 15.0 V, VAL = 0 V, 10, 11 500 9 500 see figure 3 M,D,P,L,R 2/ Switch turn “OFF” time tOFF RL = 300 , VS = +3 V 9 01, 03, 250 VAH = 4.0 V, VAL = 0 V, 10, 11 04 450 ns see figure 3 M,D,P,L,R 2/ 9 450 9 RL = 300 , VS = +3 V VAH = 15.0 V, VAL = 0 V, 02 250 10, 11 450 9 450 see figure 3 M,D,P,L,R 2/ 1/ V- = -15 V and V+ = +15 V. For device types 01, 03, and 04, VAH = +4 V and VAL = 0.8 V and for device type 02, VAH = +11 V and VAL = 3.5 V. 2/ RHA device types 01, 02, and 03 supplied to this drawing will meet all levels M, D, P, L, and R of irradiation. However, device types 01, 02, and 03 are only tested at the “R” level in accordance with MIL-STD-883 method 1019 condition A (see 1.5 herein). RHA device type 04 supplied to this drawing will meet all levels M, D, P, L, and R of irradiation for condition A and levels M, D, P, and L for condition D. However, device type 04 is only tested at the “R” level in accordance with MIL-STD-883, method 1019, condition A and tested at the “L” level in accordance with MIL-STD-883, method 1019, condition D (see 1.5 herein). Pre and post irradiation values are identical unless otherwise specified in table I. When performing post irradiation electrical measurements for any RHA level, TA = +25C. 3/ Tested initially and after any design changes which may affect these parameters. 4/ For device types 01, 03, and 04, VAL = 0 V and VAH = 4.0 V and for device type 02, VAL = 0 V and VAH = 15 V. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 7 Case outlines C and X E and Y Device types 01, 02 and 04 03 Terminal number Terminal symbol 1 NC D1 2 S3 NC 3 D3 D3 4 D1 S3 5 S1 S4 6 IN1 D4 7 GND NC 8 V- D2 9 IN2 S2 10 S2 IN2 11 D2 V+ 12 D4 NC 13 S4 GND 14 V+ V- 15 --- IN1 16 --- S1 NC = No connections FIGURE 1. Terminal connections. LOGIC SWITCH 1 - 4 0 OFF 1 ON FIGURE 2. Truth table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 8 SWITCHING TEST CIRCUIT NOTE: For device types 01, 03 and 04, VINH = +4 V. For device type 02, VINH = +15 V. FIGURE 3. Timing diagram. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 9 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q, T and V shall be in accordance with MIL-PRF-38535. 3.5.1 Certification/compliance mark. The certification mark for device classes Q, T and V shall be a "QML" or "Q" as required in MIL-PRF-38535. 3.6 Certificate of compliance. For device classes Q, T and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q, T and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q, T and V in MIL-PRF-38535 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q, and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan, including screening (4.2), qualification (4.3), and conformance inspection (4.4). The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class T, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 and the device manufacturer’s QM plan including screening, qualification, and conformance inspection. The performance envelope and reliability information shall be as specified in the manufacturer’s QM plan. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class T, screening shall be in accordance with the device manufacturer’s Quality Management (QM) plan, and shall be conducted on all devices prior to qualification and technology conformance inspection. 4.2.1 Additional criteria for device classes Q, T and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. For device classes Q, T and V interim and final electrical test parameters shall be as specified in table IIA herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, Appendix B. 4.3 Qualification inspection for device classes Q, T and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Qualification inspection for device class T shall be in accordance with the device manufacturer’s Quality Management (QM) plan. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 10 TABLE IIA. Electrical test requirements. Subgroups (in accordance with MIL-PRF-38535, table III) Test requirements Device class Q Device class V Interim electrical parameters (see 4.2) 1, 9 1, 9 Final electrical parameters (see 4.2) 1, 2, 3, 9, 1/ 10, 11 1, 2, 3, 1/, 2/ 9, 10, 11, ∆ As specified in QM plan 1, 2, 3, 4, 9, 3/ 10, 11 1, 2, 3, 4, 3/ 9, 10, 11 As specified in QM plan Group C end-point electrical parameters (see 4.4) 1, 2, 3, 9, 10, 11 1, 2, 3, 9, 2/ 10, 11, ∆ As specified in QM plan Group D end-point electrical parameters (see 4.4) 1, 9 1, 9 As specified in QM plan Group E end-point electrical parameters (see 4.4) 1, 9 1, 9 As specified in QM plan Group A test requirements (see 4.4) Device class T As specified in QM plan 1/ PDA applies to subgroup 1. For class V to subgroups 1, 9, and ∆. 2/ Delta limits (see table IIB) shall be required and the delta values shall be computed with reference to the zero hour electrical parameters (see table I). 3/ Subgroup 4, if not tested, shall be guaranteed to the limits specified in table I. 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections, and as specified herein. Inspections to be performed for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). Technology conformance inspection for class T shall be in accordance with the device manufacturer’s Quality Management (QM) plan. 4.4.1 Group A inspection. a. Tests shall be as specified in table IIA herein. b. Subgroups 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroup 4 (CC1, CC2, COS, and CIS measurements) should be measured only for initial qualification and after any process or design changes which may affect input or output capacitance. 4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.2.1 Additional criteria for device classes Q, T and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 11 TABLE IIB. Burn-in delta parameters and group C delta parameters (+25C). Parameters Symbol Conditions Device type Delta limits +RDS VD = 10 V, IS = -10 mA S1/S2/S3/S4 All 5 -RDS VD = -10 V, IS = 10 mA S1/S2/S3/S4 All 5 Leakage current into the source terminal of +IS(OFF) VS = +14 V, VD = -14 V S1/S2/S3/S4 All 2 nA an “OFF” switch -IS(OFF) VS = -14 V, VD = +14 V S1/S2/S3/S4 All 2 nA Leakage current into the drain terminal of an +ID(OFF) VS = -14 V, VD = +14 V S1/S2/S3/S4 All 2 nA “OFF” switch -ID(OFF) VS = +14 V, VD = -14 V S1/S2/S3/S4 All 2 nA Leakage current from an “ON” driver into the +ID(ON) VS = VD = +14 V S1/S2/S3/S4 All 2 nA switch (drain and source) -ID(ON) VS = VD = -14 V S1/S2/S3/S4 All 2 nA All channels VA = 0.8 V 01, 03, 04 100 nA All Channels VA = 3.5 V 02 100 nA All channels VA = 4.0 V 01, 03, 04 100 nA All channels VA = 11 V 02 100 nA All channels VA = 0.8 V 01, 03, 04 1 A VA1 = 0 V, VA2 = 4.0 V and 01, 03, 04 0.1 mA All channels VA = 0 V 02 1 A All channels VA = 15 V 02 1 A All channels VA = 0.8 V 01, 03, 04 1 A VA1 = 0 V, VA2 = 4.0 V and 01, 03, 04 1 A All channels VA = 0 V 02 1 A All channels VA = 15 V 02 1 A Switch on resistance Low level input IAL address current High level input IAH address current Positive supply I+ current VA1 = 4.0 V, VA2 = 0 V Negative supply I- current VA1 = 4.0 V, VA2 = 0 V 4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). RHA levels for device classes Q and V shall be as specified in MIL-PRF-38535. End-point electrical parameters shall be as specified in table IIA herein. 4.4.4.1 Group E inspection for device class T. For device class T, the RHA requirements shall be in accordance with the class T radiation requirements of MIL-PRF-38535. End-point electrical parameters shall be as specified in table IIA herein. 4.4.4.2 Total dose irradiation testing. Total dose irradiation testing shall be performed in accordance with MIL-STD-883 method 1019, condition A and as specified herein for device types 01, 02, 03, and 04. In addition, for device type 04 a low dose rate test shall be performed in accordance with MIL-STD-883 method 1019, condition D and as specified herein. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 12 4.4.4.2.1 Accelerated annealing test. Accelerated annealing tests shall be performed on all devices requiring a RHA level greater than 5 krads(Si). The post-anneal end-point electrical parameter limits shall be as specified in table I herein and shall be the pre-irradiation end-point electrical parameter limit at 25C 5C. Testing shall be performed at initial qualification and after any design or process changes which may affect the RHA response of the device. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q, T and V. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor prepared specification or drawing. 6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.3 Record of users. Military and industrial users should inform DLA Land and Maritime when a system application requires configuration control and which SMD's are applicable to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108. 6.4 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0540. 6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. 6.6 Sources of supply. 6.6.1 Sources of supply for device classes Q, T and V. Sources of supply for device classes Q, T and V are listed in MIL-HDBK-103 and QML-38535. The vendors listed in MIL-HDBK-103 and QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DLA Land and Maritime -VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 13 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95812 A.1 SCOPE A.1.1 Scope. This appendix establishes minimum requirements for microcircuit die to be supplied under the Qualified Manufacturers List (QML) Program. QML microcircuit die meeting the requirements of MIL-PRF-38535 and the manufacturers approved QM plan for use in monolithic microcircuits, multi-chip modules (MCMs), hybrids, electronic modules, or devices using chip and wire designs in accordance with MIL-PRF-38534 are specified herein. Two product assurance classes consisting of military high reliability (device class Q) and space application (device class V) are reflected in the Part or Identification Number (PIN). When available, a choice of Radiation Hardiness Assurance (RHA) levels are reflected in the PIN. A.1.2 PIN. The PIN is as shown in the following example: 5962 R Federal stock class designator \ RHA designator (see A.1.2.1) 01 V 9 A Device type (see A.1.2.2) Device class designator (see A.1.2.3) Die code Die details (see A.1.2.4) 95812 / \/ Drawing number A.1.2.1 RHA designator. Device classes Q and V RHA identified die meet the MIL-PRF-38535 specified RHA levels. A dash (-) indicates a non-RHA die. A.1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 04 HS-302RH HS-302EH Circuit function Radiation hardened DI dual DPST CMOS switch Radiation hardened DI dual DPST CMOS switch A.1.2.3 Device class designator. Device class Q or V STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 Device requirements documentation Certification and qualification to the die requirements of MIL-PRF-38535 SIZE 5962-95812 A REVISION LEVEL E SHEET 14 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95812 A.1.2.4 Die details. The die details designation is a unique letter which designates the die's physical dimensions, bonding pad location(s) and related electrical function(s), interface materials, and other assembly related information, for each product and variant supplied to this appendix. A.1.2.4.1 Die physical dimensions. Die type Figure number 01, 04 A-1 A.1.2.4.2 Die bonding pad locations and electrical functions. Die type Figure number 01, 04 A-1 A.1.2.4.3 Interface materials. Die type Figure number 01, 04 A-1 A.1.2.4.4 Assembly related information. Die type Figure number 01, 04 A-1 A.1.3 Absolute maximum ratings. See paragraph 1.3 herein for details. A.1.4 Recommended operating conditions. See paragraph 1.4 herein for details. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 15 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95812 A.2 APPLICABLE DOCUMENTS. A.2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARD MIL-STD-883 - Test Method Standard Microcircuits. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) A.2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. A.3 REQUIREMENTS A.3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer’s Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. A.3.2 Design, construction and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein and the manufacturer’s QM plan for device classes Q and V. A.3.2.1 Die physical dimensions. The die physical dimensions shall be as specified in A.1.2.4.1 and on figure A-1. A.3.2.2 Die bonding pad locations and electrical functions. The die bonding pad locations and electrical functions shall be as specified in A.1.2.4.2 and on figure A-1. A.3.2.3 Interface materials. The interface materials for the die shall be as specified in A.1.2.4.3 and on figure A-1. A.3.2.4 Assembly related information. The assembly related information shall be as specified in A.1.2.4.4 and on figure A-1. A.3.2.5 Truth table. The truth table shall be as defined in paragraph 3.2.3 herein. A.3.2.6 Radiation exposure circuit. The radiation exposure circuit shall be as defined in paragraph 3.2.4 herein. A.3.3 Electrical performance characteristics and post-irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post-irradiation parameter limits are as specified in table I of the body of this document. A.3.4 Electrical test requirements. The wafer probe test requirements shall include functional and parametric testing sufficient to make the packaged die capable of meeting the electrical performance requirements in table I. A.3.5 Marking. As a minimum, each unique lot of die, loaded in single or multiple stack of carriers, for shipment to a customer, shall be identified with the wafer lot number, the certification mark, the manufacturer’s identification and the PIN listed in A.1.2 herein. The certification mark shall be a “QML” or “Q” as required by MIL-PRF-38535. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 16 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95812 A.3.6 Certification of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see A.6.4 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply for this appendix shall affirm that the manufacturer’s product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and the requirements herein. A.3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 shall be provided with each lot of microcircuit die delivered to this drawing. A.4 VERIFICATION A.4.1 Sampling and inspection. For device classes Q and V, die sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer’s Quality Management (QM) plan. The modifications in the QM plan shall not affect the form, fit, or function as described herein. A.4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and as defined in the manufacturer’s QM plan. As a minimum, it shall consist of: a. Wafer lot acceptance for class V product using the criteria defined in MIL-STD-883, method 5007. b. 100% wafer probe (see paragraph A.3.4 herein). c. 100% internal visual inspection to the applicable class Q or V criteria defined in MIL-STD-883, method 2010 or the alternate procedures allowed in MIL-STD-883, method 5004. A.4.3 Conformance inspection. A.4.3.1 Group E inspection. Group E inspection is required only for parts intended to be identified as radiation assured (see A.3.5 herein). RHA levels for device classes Q and V shall be as specified in MIL-PRF-38535. End point electrical testing of packaged die shall be as specified in table IIA herein. Group E tests and conditions are as specified in paragraphs 4.4.4, 4.4.4.1, 4.4.4.2, and 4.4.4.2.1 herein. A.5 DIE CARRIER A.5.1 Die carrier requirements. The requirements for the die carrier shall be accordance with the manufacturer’s QM plan or as specified in the purchase order by the acquiring activity. The die carrier shall provide adequate physical, mechanical and electrostatic protection. A.6 NOTES A.6.1 Intended use. Microcircuit die conforming to this drawing are intended for use in microcircuits built in accordance with MIL-PRF-38535 or MIL-PRF-38534 for government microcircuit applications (original equipment), design applications, and logistics purposes. A.6.2 Comments. Comments on this appendix should be directed to DLA Land and Maritime -VA, Columbus, Ohio, 43218-3990 or telephone (614)-692-0540. A.6.3 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. A.6.4 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535. The vendors listed within QML-38535 have submitted a certificate of compliance (see A.3.6 herein) to DLA Land and Maritime -VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 17 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95812 Die bonding pad locations and electrical functions NOTE: Pad numbers reflect terminal numbers when placed in case outlines C and X (see figure 1). Die physical dimensions. Die size: 2130 microns x 1930 microns. Die thickness: 11 ± 1 mils. Interface materials. Top metallization: Al 10.0 kÅ ~ 15.0 kÅ Backside metallization: Gold Glassivation. Type: Phosphorus doped Si02 Thickness: 6.4 kÅ ~ 9.6 kÅ Substrate: DI (dielectric isolation) Assembly related information. Substrate potential: Unbiased Special assembly instructions: None FIGURE A-1. Die bonding pad locations and electrical functions. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-95812 A REVISION LEVEL E SHEET 18 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 14-11-18 Approved sources of supply for SMD 5962-95812 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962R9581201QCC 34371 HS1-302RH-8 5962R9581201QXC 34371 HS9-302RH-8 5962R9581201TCC 3/ HS1-302RH-T 5962R9581201TXC 3/ HS9-302RH-T 5962R9581201VCC 34371 HS1-302RH-Q 5962R9581201VXC 34371 HS9-302RH-Q 5962R9581201V9A 34371 HS0-302RH-Q 5962R9581202VCC 3/ HS1-306RH-Q 5962R9581202VXC 3/ HS9-306RH-Q 5962R9581203VEC 3/ HS1-384RH-Q 5962R9581203VYC 3/ HS9-384RH-Q 5962R9581204VCC 34371 HS1-302EH-Q 5962R9581204VXC 34371 HS9-302EH-Q 5962R9581204V9A 34371 HS0-302EH-Q 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number 34371 Vendor name and address Intersil Corporation 1001 Murphy Ranch Road Milpitas, CA 95035-6803 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.