Datasheet 2.7V to 5.5V Input, 3.0A Integrated MOSFET Single Synchronous Buck DC/DC Converter BD9B300MUV General Description Key Specifications BD9B300MUV is a synchronous buck switching regulator with built-in low on-resistance power MOSFETs. This IC, which is capable of providing current up to 3A, features fast transient response by employing constant on-time control system. It offers high oscillating frequency at low inductance. With its original constant on-time control method which operates low consumption at light load, this product is ideal for equipment and devices that demand minimal standby power consumption. Input Voltage Range: 2.7V to 5.5V Output Voltage Range: 0.8 V to VPVIN x 0.8 V Maximum Operating Current: 3A (Max) Switching Frequency: 2MHz/1MHz (Typ) High-Side MOSFET ON Resistance: 35mΩ (Typ) Low-Side MOSFET ON Resistance: 35mΩ (Typ) Standby Current: 0μA (Typ) Package W (Typ) x D (Typ) x H (Max) 3.00 mm x 3.00 mm x 1.00 mm VQFN016V3030 Features Synchronous Single DC/DC Converter Constant on-time control suitable to Deep-SLLM Over Current Protection Short Circuit Protection Thermal Shutdown Protection Under Voltage Lockout Protection Adjustable Soft Start Power Good Output VQFN016V3030 Package (backside heat dissipation) Applications VQFN016V3030 Step-down Power Supply for DSPs, FPGAs, Microprocessors, etc. Laptop PCs/Tablet PCs/Servers LCD TVs Storage Devices (HDDs/SSDs) Printers, OA Equipment Entertainment Devices Distributed Power Supply, Secondary Power Supply Typical Application Circuit PGD VIN PGD PVIN AVIN Enable 10µF BOOT EN CBOOT 0.1µF VOUT AGND SW 1.0µH PGND R1 SS CFB 22µF×2 MODE CSS FREQ FB R2 Figure 1. Application Circuit 〇Product structure : Silicon monolithic integrated circuit .www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 14 • 001 〇This product has no designed protection against radioactive rays 1/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Pin Configuration PGD BOOT FREQ MODE EN FB AGND AVIN (TOP VIEW) Figure 2. Pin Assignment Pin Descriptions Pin No. Pin Name 1, 2 PVIN 3, 4 PGND Ground terminals for the output stage of the switching regulator. 5 AGND Ground terminal for the control circuit. 6 FB 7 FREQ Terminal for setting switching frequency. Connecting this terminal to ground makes switching to operate constant on-time corresponding to 2.0MHz. Connecting this terminal to AVIN makes switching to operate constant on-time corresponding to 1.0MHz. This terminal needs to be terminated. 8 MODE Terminal for setting switching control mode. Connecting this terminal to AVIN forces the device to operate in the fixed frequency PWM mode. Connecting this terminal to ground enables the Deep-SLLM control and the mode is automatically switched between the Deep-SLLM control and fixed frequency PWM mode. 9 SS Terminal for setting the soft start time. The rise time of the output voltage can be specified by connecting a capacitor to this terminal. See page 23 for how to calculate the capacitance. 10, 11, 12 SW Switch nodes. These terminals are connected to the source of the High-Side MOSFET and drain of the Low-Side MOSFET. Connect a bootstrap capacitor of 0.1 µF between these terminals and BOOT terminal. In addition, connect an inductor of 0.47µH to 1µH (FREQ=L), 1μH to 1.5μH (FREQ=H) considering the direct current superimposition characteristic. 13 BOOT Terminal for bootstrap. Connect a bootstrap capacitor of 0.1 µF between this terminal and SW terminals. The voltage of this capacitor is the gate drive voltage of the High-Side MOSFET. 14 PGD A “Power Good” terminal, an open drain output. Use of pull up resistor is needed. See page 17 for how to specify the resistance. When the FB terminal voltage reaches more than 80% of 0.8 V, the internal Nch MOSFET turns off and the output turns High. 15 EN 16 AVIN Terminal for supplying power to the control circuit of the switching regulator. Connecting a 0.1µF ceramic capacitor is recommended. - E-Pad A backside heat dissipation exposed pad. Connecting to the internal PCB ground plane by using multiple vias provides excellent heat dissipation characteristics. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 Function Power supply terminals for the switching regulator. These terminals supply power to the output stage of the switching regulator. Connecting a 10µF ceramic capacitor is recommended. An inverting input node for the error amplifier and main comparator. See page 22 for how to calculate the resistance of the output voltage setting. Enable terminal. Turning this terminal signal Low (0.3V or lower) forces the device to enter the shutdown mode. Turning this terminal signal High (2.0V or higher) enables the device. This terminal must be terminated. 2/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Block Diagram AVIN 1 PVIN 2 EN OCP SCP UVLO BOOT FB 6 Error Amplifier SS 9 Main Comparator On Time Modulation Control Logic + DRV On Time Soft Start SW VOUT Voltage Reference 3 TSD PGOOD PGND 4 5 7 PGD FREQ 8 AGND MODE PGD Figure 3. Block Diagram www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 3/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Description of Blocks ● VREF The VREF block generates the internal reference voltage. ● UVLO The UVLO block is for Under Voltage lockout protection. It will shut down the IC when VIN falls to 2.45 V (Typ) or lower. The threshold voltage has a hysteresis of 100mV (Typ). ● TSD The TSD block is for thermal protection. The thermal protection circuit shuts down the device when the internal temperature of IC rises to 175°C (Typ) or higher. Thermal protection circuit resets when the temperature falls. The circuit has a hysteresis of 25°C (Typ). ● Soft Start The Soft Start circuit slows down the rise of output voltage during start-up and controls the current, which allows the prevention of output voltage overshoot and inrush current. A built-in soft start function is provided and a soft start is initiated in 1msec (Typ) when the SS terminal is open. ● Control Logic + DRV This block is a DC/DC driver. A signal from On Time is applied to drive the MOSFETs. ● PGOOD When the FB terminal voltage reaches more than 80% of 0.8 V, the Nch MOSFET of the built-in open drain output turns off and the output turns High. ● OCP/SCP After soft start is completed and in condition where output voltage is below 70% (typ) of voltage setting, it counts the number of times of which current flowing in High side FET reaches over current limit. When 1024 times is counted it stops operation for 1m sec (typ.) and re-operates. Counting is reset when output voltage is above 80% (typ.) of voltage setting or when EN, UVLO, SCP function is re-operated. ● Error Amplifier Adjusts Main Comparator input to make internal reference voltage equal to FB terminal voltage. ● Main Comparator Main comparator compares Error Amplifier output and FB terminal voltage. When FB terminal voltage becomes low it outputs High and reports to the On Time block that the output voltage has dropped below control voltage. ● On Time This is a block which creates On Time. Requested On Time is created when Main Comparator output becomes High. On Time is adjusted to restrict frequency change even with I/O voltage change. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 4/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Absolute Maximum Ratings (Ta = 25°C) Parameter Supply Voltage EN Terminal Voltage Symbol Rating Unit VPVIN, VAVIN -0.3 to +7 V VEN -0.3 to +7 V MODE Terminal Voltage VMODE -0.3 to +7 V FREQ Terminal Voltage VFREQ -0.3 to +7 V PGD Terminal Voltage VPGD -0.3 to +7 V Voltage from GND to BOOT VBOOT -0.3 to +14 V Voltage from SW to BOOT ⊿VBOOT -0.3 to +7 V FB Terminal Voltage VFB -0.3 to +7 V SW Terminal Voltage VSW -0.3 to VPVIN + 0.3 V Output Current IOUT 3.5 A Pd 2.66 W Allowable Power Dissipation(Note 1) Operating Temperature Range Topr -40 to 85 C Storage Temperature Range Tstg -55 to 150 C (Note 1) When mounted on a 70mm x 70mm x 1.6mm 4-layer glass epoxy board (copper foil area: 70 mm x 70 mm) Derate by 21.3mW when operating above 25C Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Recommended Operating Conditions (Ta= -40°C to +85°C) Parameter Supply Voltage Output Current (Note 2) Output Voltage Range Symbol Min Typ Max Unit VPVIN, VAVIN 2.7 - 5.5 V IOUT - - 3 A VRANGE 0.8 - VPVIN × 0.8 V (Note 3) Pd, ASO should not be exceeded www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 5/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Electrical Characteristics (Unless otherwise specified Ta=25°C, VAVIN = VPVIN = 5V, VEN = 5V, VMODE = GND) Parameter Symbol Min Typ Max Unit Conditions Standby Supply Current ISTB - 0 10 µA Operating Supply Current ICC - 35 50 µA UVLO Detection Threshold VUVLO1 2.35 2.45 2.55 V EN=GND FREQ=AVIN, IOUT=0mA Non switching VIN falling UVLO Release Threshold VUVLO2 2.425 2.55 2.7 V VIN rising VUVLOHYS 50 100 200 mV EN Input High Level Voltage VENH 2.0 - - V EN Input Low Level Voltage VENL - - 0.3 V IEN - 0 10 µA FB Terminal Voltage VFB 0.792 0.8 0.808 V FB Input Bias Current IFB - - 1 µA FB=0.8V Internal Soft Start Time TSS 0.5 1.0 2.0 ms With internal constant Soft Start Terminal Current ISS 0.5 1.0 2.0 µA FREQ Input High Level Voltage VFRQH VAVIN-0.3 - - V FREQ Input Low Level Voltage VFRQL - - 0.3 V MODE Input High Level Voltage VMODEH VAVIN-0.3 - - V MODE Input Low Level Voltage VMODEL - - 0.3 V On time1 ONT1 96 120 144 ns VOUT=1.2V, FREQ=GND On time2 ONT2 192 240 288 ns VOUT=1.2V, FREQ=AVIN Power Good Rising Threshold VPGDH 75 80 85 % Power Good Falling Threshold VPGDL 65 70 75 % Output Leakage Current ILKPGD - 0 5 µA FB rising, VPGDH=FB/VFBx100 FB falling, VPGDL=FB/VFBx100 PGD=5V Power Good On Resistance RPGD - 100 200 Ω Power Good Low Level Voltage PGDVL - 0.1 0.2 V High Side FET On Resistance RONH - 35 70 mΩ Low Side FET On Resistance RONL - 35 70 mΩ High Side Output Leakage Current RILH - 0 10 µA No switching Low Side Output Leakage Current RILL - 0 10 µA No switching AVIN pin UVLO Hysteresis Enable EN Input Current EN=5V Reference Voltage, Error Amplifier Control Power Good IPGD=1mA SW www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 6/30 BOOT - SW = 5 V TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Typical Performance Curves 3.0 40 VIN=5V 35 2.5 2.0 VIN=3.3V 25 ISTBY [uA] ICC [uA] 30 20 15 1.5 1.0 10 VIN=5V 0.5 5 VIN=3.3V 0 0.0 -40 -20 0 20 40 Temperature [°C] 60 -40 80 100 60 80 100 MODE=L MODE=L 90 80 80 70 70 Efficiency [%] Efficiency[%] 0 20 40 Temperature [°C] Figure 5. Stand-by Supply Current vs Temperature Figure 4. Operating Supply Current vs Temperature 90 -20 60 50 MODE=H 40 60 50 MODE=H 40 30 30 20 20 VOUT=1.2V, FREQ=L 10 VOUT=1.2V, FREQ=L 10 0 0 1 10 100 1000 Load Current [mA] 10000 1 Figure 6. Efficiency vs Load Current (VIN=5V, VOUT=1.2V, L=1.0µH, FREQ=L) www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 10 100 1000 Load Current [mA] 10000 Figure 7. Efficiency vs Load Current (VIN=5V, VOUT=1.2V, L=1.5µH, FREQ=H) 7/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Typical Performance Curves - continued 100 100 90 90 MODE=L 80 70 60 Efficiency [%] 70 Efficiency [%] MODE=L 80 MODE=H 50 40 30 MODE=H 60 50 40 30 20 20 VOUT=3.3V, FREQ=L 10 VOUT=3.3V FREQ=H 10 0 0 1 10 100 LOAD [mA] 1000 10000 1 10 1000 10000 Figure 9. Efficiency vs Load Current (VIN=5V, VOUT=3.3V, L=1.5µH, FREQ=H) Figure 8. Efficiency vs Load Current (VIN=5V, VOUT=3.3V, L=1.0µH, FREQ=L) 2.60 0.808 0.806 2.56 Release 0.804 2.52 VUVLO [V] VIN=5V 0.802 VFB [V] 100 LOAD [mA] 0.800 VIN=3.3V 0.798 2.48 2.44 0.796 Detect 2.40 0.794 0.792 2.36 -40 -20 0 20 40 Temperature [°C] 60 -40 80 Figure 10. FB Voltage vs Temperature www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 -20 0 20 40 Temperature [°C] 60 80 Figure 11. UVLO Threshold vs Temperature 8/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Typical Performance Curves - continued 2.0 2.5 VIN=5.0V 1.8 VIN=5V 2.0 1.6 UP VIN=3.3V 1.2 1.0 VIN =5.0V DOWN 0.8 IEN [μA] VEN [V] 1.4 1.5 1.0 0.6 0.4 0.5 VIN=3.3V 0.2 0.0 0.0 -40 -20 0 20 40 Temperature [°C] 60 -40 80 Figure 12. EN Threshold vs Temperature -20 0 20 40 Temperature [°C] 60 80 Figure 13. EN Input Current vs Temperature 2.5 3.5 VIN=5V 3.0 2.0 VIN=5V IFREQ [μA] VFREQ [V] 2.5 2.0 1.5 1.0 VIN=3.3V 1.5 0.5 1.0 0.5 0.0 -40 -20 0 20 40 Temperature [°C] 60 80 -40 Figure 14. FREQ Threshold vs Temperature www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 -20 0 20 40 Temperature [°C] 60 80 Figure 15. FREQ Input Current vs Temperature 9/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Typical Performance Curves - continued 3.5 6.0 VIN=5V VIN=5V 3.0 5.5 5.0 IMODE [μA] VMODE [V] 2.5 2.0 VIN=3.3V 1.5 4.0 1.0 3.5 3.0 0.5 -40 -20 0 20 40 Temperature [°C] 60 -40 80 Figure 16. MODE Threshold Voltage vs Temperature -20 0 20 40 Temperature [°C] 60 80 Figure 17. MODE Input Current vs Temperature 40.0 40.0 37.5 37.5 35.0 35.0 32.5 32.5 RONL [m Ω] RONH [m Ω] 4.5 VIN=3.3V 30.0 VIN=3.3V 30.0 27.5 27.5 25.0 25.0 22.5 22.5 VIN=5V VIN=5V 20.0 20.0 -40 -20 0 20 40 Temperature [°C] 60 80 Figure 18. High Side ON-Resistance www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 -40 -20 0 20 40 Temperature [°C] 60 80 Figure 19. Low Side ON-Resistance 10/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Typical Performance Curves - continued 120 85 RISING 80 110 PGD ON抵抗[Ω] VPGD [%] VIN=3.3V 75 70 100 90 VIN=5V 80 FALLING 65 70 60 60 -40 -20 0 20 40 Temperature [°C] 60 -40 80 Figure 20. PGD Threshold vs Temperature -20 0 20 40 Temperature [°C] 60 80 Figure 21. PGD ON ON-Resistance vs Temperature 2.0 3.0 2.5 1.5 1.0 2.0 ISS [μA] TSS [msec] VIN=3.3V VIN=5V 1.5 VIN=5V 1.0 0.5 VIN=3.3V 0.5 0.0 0.0 -40 -20 0 20 40 Temperature [°C] 60 80 Figure 22. Soft Start Time vs Temperature www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 -40 -20 0 20 40 Temperature [°C] 60 80 Figure 23. SS Terminal Current vs Temperature 11/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Typical Performance Curves - continued 2400 1200 MODE=H 2000 1000 1600 800 fSW [kHz] fSW [kHz] MODE=H 1200 800 400 400 MODE=L 200 FREQ=L VIN=5V MODE=L 0 FREQ=H VIN=5V 0 0 500 1000 1500 2000 Load Current [mA] 2500 3000 0 Figure 24. Switching Frequency vs Load Current 500 1000 1500 2000 Load Current [mA] 2500 3000 Figure 25. Switching Frequency vs Load Current 2400 1200 2300 1150 2200 1100 2100 1050 fSW [kHz] fSW [kHz] 600 2000 1900 1000 950 1800 900 VOUT=1.2V MODE=H FREQ=L IOUT=1A 1700 VOUT=1.2V MODE=H FREQ=H IOUT=1A 850 1600 800 3.0 3.5 4.0 4.5 5.0 VIN Input Voltage [V] 5.5 3.0 Figure 26. Switching Frequency vs Input Voltage www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 3.5 4.0 4.5 5.0 VIN Input Voltage [V] 5.5 Figure 27. Switching Frequency vs Input Voltage 12/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Typical Performance Curves - continued VIN=5V/div VIN=5V/div EN=5V/div EN=5V/div Time=1ms/div Time=1ms/div VOUT=1V/div VOUT=1V/div SW=5V/div SW=5V/div Figure 29. Power Down Waveform with EN (FREQ=H, RLOAD=0.5Ω) Figure 28. Power Up Waveform with EN (FREQ=H, RLOAD=0.5Ω) VIN=5V/div VIN=5V/div EN=5V/div EN=5V/div Time=1ms/div Time=1ms/div VOUT=1V/div VOUT=1V/div SW=5V/div SW=5V/div Figure 30. Power Up Waveform with VIN (FREQ=H, RLOAD=0.5Ω) www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 Figure 31. Power Down Waveform with VIN (FREQ=H, RLOAD=0.5Ω) 13/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Typical Performance Curves - continued VOUT=20mV/div SW=2V/div VOUT=20mV/div Time=1µs/div SW=2V/div Figure 33. Switching Waveform (VIN=5V, VOUT=1.2V, FREQ=L, IOUT=3A) Figure 32. Switching Waveform (VIN=5V, VOUT=1.2V, FREQ=L, IOUT=0.1A) VOUT=20mV/div SW=2V/div VOUT=20mV/div Time=1µs/div SW=2V/div Figure 34. Switching Waveform (VIN=5V, VOUT=1.2V, FREQ=H, IOUT=0.2A) www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 Time=1µs/div Time=1µs/div Figure 35. Switching Waveform (VIN=5V, VOUT=1.2V, FREQ=H, IOUT=3A) 14/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV - continued 1.0 1.0 0.8 0.8 0.6 0.6 Output Voltage Deviation[%] Output Voltage Deviation[%] Typical Performance Curves 0.4 0.2 MODE=H 0.0 -0.2 MODE=L -0.4 0.4 0.2 0.0 -0.2 MODE=H -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 MODE=L -1.0 2.5 3.0 3.5 4.0 4.5 VIN Input Voltage[V] 5.0 0.0 5.5 1.0 1.5 2.0 Load Current [A] 2.5 3.0 Figure 37. Load Regulation (VIN=5V, VOUT=1.2V, L=1.5μH, FREQ=H) Figure 36. Line Regulation (VOUT=1.2V, L=1.5μH, FREQ=H) VOUT=50mV/div VOUT=50mV/div IOUT=1A/div 0.5 Time=0.5m/div IOUT=1A/div Time=0.5m/div Figure 38. Load Transient Response IOUT=0.1A to 2A Figure 39. Load Transient Response IOUT=0A to 3A (VIN=5V, VOUT=1.2V, FREQ=L, MODE=L, COUT=Ceramic 44µF) (VIN=5V, VOUT=1.2V, FREQ=L, MODE=H, COUT=Ceramic 44µF) www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 15/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Application Example(s) 1. Basic Operation (1) DC/DC Converter operation BD9B300MUV is a synchronous rectifying step-down switching regulator that achieves faster transient response by employing constant on-time control system. It utilizes switching operation in PWM (Pulse Width Modulation) mode for heavier load, while it utilizes Deep-SLLM (Simple Light Load Mode) control for lighter load to improve efficiency. Deep-SLLMTM Control Efficiency η[%] ① ② PWM Control Output Current IOUT [A] Figure 40. Efficiency (Deep-SLLM ① Deep-SLLM TM TM Control and PWM Control) ②PWM Control Control VOUT 20mV/div VOUT 20mV/div SW 2.0V/div SW 2.0V/div Figure 41. Switching Waveform at Deep-SLLMTM Control (VIN=5.0V, VOUT=1.2V, IOUT=100mA) www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 16/30 Figure 42. Switching Waveform at PWM Control (VIN=5.0V, VOUT=1.2V, IOUT=3A) TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV (2) Enable Control The IC shutdown can be controlled by the voltage applied to the EN terminal. When VEN reaches 2.0 V(Typ), the internal circuit is activated and the IC starts up. To enable shutdown control with the EN terminal, the shutdown interval (Low level interval of EN) must be set to 100 µs or longer. VEN EN terminal VENH VENL 0 t VOUT Output setting voltage 0 Soft start 1 msec (typ.) t Figure 43. Start Up and Down with Enable (3) Power Good When the output voltage reaches more than 80% of the voltage setting, the open drain NMOSFET, internally connected to the PGD terminal, turns off and the PGD terminal turns to Hi-z condition. Also when the output voltage falls below 70% of voltage setting, the open drain NMOS FET turns on and PGD terminal pulls down with 100Ω. Connecting a pull up resistor (10KΩ to 100KΩ) is recommended. Figure 44. Power Good Timing Chart (4) Soft Start When EN terminal is turned High, Soft Start operates and output voltage gradually rises. With the Soft Start Function, over shoot of output voltage and rush current can be prevented. Rising time of output voltage when SS terminal is open is 1msec (typ.). Capacitor connected to SS terminal makes rising time more than 1msec. Please refer to page 23 for the method of setting rising time. Figure 45. Soft Start Timing Chart www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 17/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV 2. Protection The protective circuits are intended for prevention of damage caused by unexpected accidents. Do not use them for continuous protective operation (1) Over Current Protection (OCP) / Short Circuit Protection (SCP) Setting of Over current protection is 5.0A (typ.). When OCP is triggered, over current protection is realized by restricting On / Off Duty of current flowing in upper MOSFET by each switching cycle. Also, if Over current protection operates 1024 cycles in a condition where FB terminal voltage reaches below 70% of internal standard voltage, Short Circuit protection (SCP) operates and stops switching for 1msec (typ.) before it initiates restart. However, during startup, Short circuit protection will not operate even if the IC is still in the SCP condition. Table 1. Over Current Protection / Short Circuit Protection Function Over current EN terminal PGD Startup protection While start up Valid L More than 2.0V Startup completed Valid Less than 0.3V Short circuit protection Invalid Valid H ＊ Valid Invalid ＊ ＊ Invalid Invalid 1ms(typ.) VOUT FB High side MOSFET gate Low side MOSFET gate OCP threshold Coil current Inside IC OCP signal 1024 Cycle PGD Figure 46. Short Circuit Protection (SCP) Timing Chart www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 18/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV (2) Under Voltage Lockout Protection (UVLO) The Under Voltage Lockout Protection circuit monitors the AVIN terminal voltage. The operation enters standby when the AVIN terminal voltage is 2.45V (Typ) or lower. The operation starts when the AVIN terminal voltage is 2.55V (Typ) or higher. VIN UVLO OFF hys UVLO ON 0V VOUT Soft start FB terminal High side MOSFET gate Low side MOSFET gate Normal operation UVLO Normal operation Figure 47. UVLO Timing Chart (3) Thermal Shutdown When the chip temperature exceeds Tj=175C, the DC/DC converter output is stopped. The thermal shutdown circuit is intended for shutting down the IC from thermal runaway in an abnormal state with the temperature exceeding Tjmax=150C. It is not meant to protect or guarantee the soundness of the application. Do not use the function of this circuit for application protection design. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 19/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Application Example Figure 48. Application Circuit Table 2. Recommended Component Values (VIN=5V, FREQ=H) VOUT Reference Designator 1.0V 1.2V 1.5V 1.8V 3.3V R5 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ - R7 75kΩ 75kΩ 160kΩ 150kΩ 160kΩ - R8 300kΩ 150kΩ 180kΩ 120kΩ 51kΩ - C2 10μF 10μF 10μF 10μF 10μF 10V, X5R, 3216 C4 0.1μF 0.1μF 0.1μF 0.1μF 0.1μF 25V, X5R, 1608 C8 0.1μF 0.1μF 0.1μF 0.1μF 0.1μF - C9 22μF 22μF 22μF 22μF 22μF 6.3V, X5R, 3225 C10 22μF 22μF 22μF 22μF 22μF 6.3V, X5R, 3225 C14 120p 120pF 150pF 180pF 180pF - L1 1.5μH 1.5μH 1.5μH 1.5μH 1.5μH TOKO, FDSD0630 Description Table 3. Recommended Component Values (VIN=5V, FREQ=L) VOUT Reference Designator 1.0V 1.2V 1.5V 1.8V 3.3V R5 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ - R7 75kΩ 75kΩ 160kΩ 150kΩ 160kΩ - R8 300kΩ 150kΩ 180kΩ 120kΩ 51kΩ - C2 10μF 10μF 10μF 10μF 10μF 10V, X5R, 3216 C4 0.1μF 0.1μF 0.1μF 0.1μF 0.1μF 25V, X5R, 1608 C8 0.1μF 0.1μF 0.1μF 0.1μF 0.1μF - C9 22μF 22μF 22μF 22μF 22μF 6.3V, X5R, 3225 C10 22μF 22μF 22μF 22μF 22μF 6.3V, X5R, 3225 C14 100p 120pF 100pF 120pF 120pF - L1 1.0μH 1.0μH 1.0μH 1.0μH 1.0μH TOKO, FDSD0630 www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 20/30 Description TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Selection of Components Externally Connected 1. Output LC Filter Constant In order to supply a continuous current to the load, the DC/DC converter requires an LC filter for smoothing the output voltage. It is recommended to use inductors of values 0.47µH to 1.0µH when FREQ=L or 1.0µH to 1.5µH at FREQ=H. IL Inductor saturation current > IOUTMAX +⊿IL /2 IOUTMAX ⊿IL Average inductor current t Figure 49. Waveform of current through inductor Inductor ripple current ΔIL ΔI L V OUT V IN -V OUT 1 FOSC V IN Figure 50. Output LC filter circuit 608 mA L Where: VIN= 5V VOUT= 1.2V L=1.5µH FOSC=1MHz (switching frequency) The saturation current of the inductor must be larger than the sum of the maximum output current and 1/2 of the inductor ripple current ∆IL. The output capacitor COUT affects the output ripple voltage characteristics. The output capacitor COUT must satisfy the required ripple voltage characteristics. The output ripple voltage can be represented by the following equation. ΔV RPL ΔI L R ESR 1 8 C OUT FOSC V where RESR is the Equivalent Series Resistance (ESR) of the output capacitor. * The capacitor rating must allow a sufficient margin with respect to the output voltage. The output ripple voltage can be decreased with a smaller ESR. A ceramic capacitor of about 22 µF to 47 µF is recommended. *Be careful of total capacitance value, when additional capacitor CLOAD is connected in addition to output capacitor COUT. Use maximum additional capacitor CLOAD (Max) condition which satisfies the following condition. Maximum starting inductor ripple current ILSTART Over Current limit 3.8A min Maximum starting inductor ripple current ILSTART can be expressed using the following equation. ILSTART Maximum starting output current I OMAX www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 21/30 Charge current to output capacitor I CAP ΔI L 2 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Charge current to output capacitor ICAP can be expressed using the following equation. I CAP C OUT C LOAD TSS VOUT [A ] For example, given VIN= 5V, VOUT= 3.3V, L= 1.5µH, switching frequency FOSC= 800kHz(Min), Output capacitor COUT= 44µF, Soft Start time TSS= 0.5ms(Min), and load current during soft start IOSS= 3A, maximum CLOAD can be computed using the following equation. C LOAD max 3.8 ‐ I OSS ‐ ΔI L /2 TSS VOUT ‐ C OUT 6.38 μF If the value of CLOAD is large, and cannot meet the above equation, adjust the value of the capacitor CSS to meet the condition below. 3.8 ‐ I OSS ‐ ΔI L /2 V OUT I SS C LOAD max V FB C SS ‐ C OUT (Refer to the following items (3) Soft Start Setting equation of time TSS and soft-start value of the capacitor to be connected to the CSS.) For example, given VIN = 5V, VOUT = 3.3V, L = 1.5µH, load current during soft start IOSS = 3A, switching frequency FOSC= 800kHz (Min), Output capacitor COUT = 44µF, VFB = 0.792V(Max), ISS = 3.6µA(Max), with CLOAD = 220uF, capacitor CSS is computed as follows. C SS V OUT I SS 3.8 ‐ I OSS ‐ ΔI L /2 V FB C LOAD C OUT 6617 pF 2. Output Voltage Setting The output voltage value can be set by the feedback resistance ratio. For stable operation, it is recommended to use feedback resistance R1 of more than 20kΩ. VOUT VOUT R1 Error Amplifier R1 R2 R2 0.8 V FB R2 0.8V R2 0.8 VOUT ‐ 0.8 R1 Ω Figure 51. Feedback Resistor Circuit www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 22/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV 3. Soft Start Setting Turning the EN terminal signal High activates the soft start function. This causes the output voltage to rise gradually while the current at startup is placed under control. This allows the prevention of output voltage overshoot and inrush current. The rise time depends on the value of the capacitor connected to the SS terminal. TSS C SS V FB /I SS C SS I SS TSS /V FB T SS : Soft Start Time C SS : Capacitor connected to Soft Start Time Terminal V FB : FB Terminal Voltage (0.8V (Typ)) I SS : Soft Start Terminal Source Current (1.0μA(Typ)) with C SS TSS 0.01 F , 0.01μF 0.8 V ) /1.0 μA 8.0 msec Turning the EN terminal signal High with the SS terminal open or with the terminal signal High (no capacitor connected) causes the output voltage to rise in 1msec (Typ). 4. FB Capacitor Generally, in fixed ON time control (hysteresis control), sufficient ripple voltage in FB voltage is needed to operate comparator stably. Regarding this IC, by injecting ripple voltage to FB voltage inside IC it is designed to correspond to low ESR output capacitor. Please set the FB capacitor within the range of the following expression to inject an appropriate ripple. VOUT 1‐ VOUT V IN VOUT 3 C FB f SW 7.5 10 f SW VIN : Input Voltage VOUT : Output Voltage fSW : Switching Frequency www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 1‐ VOUT V IN 3.6 10 3 23/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV PCB Layout Design In the step-down DC/DC converter, a large pulse current flows into two loops. The first loop is the one into which the current flows when the High-Side FET is turned ON. The flow starts from the input capacitor CIN, runs through the FET, inductor L and output capacitor COUT and back to GND of CIN via GND of COUT. The second loop is the one into which the current flows when the Low-Side FET is turned on. The flow starts from the Low-Side FET, runs through the inductor L and output capacitor COUT and back to GND of the Low-Side FET via GND of COUT. Route these two loops as thick and as short as possible to allow noise to be reduced for improved efficiency. It is recommended to connect the input and output capacitors directly to the GND plane. The PCB layout has a great influence on the DC/DC converter in terms of all of the heat generation, noise and efficiency characteristics. Figure 52. Current Loop of Buck Converter Accordingly, design the PCB layout considering the following points. Connect an input capacitor as close as possible to the IC PVIN terminal on the same plane as the IC. If there is any unused area on the PCB, provide a copper foil plane for the GND node to assist heat dissipation from the IC and the surrounding components. Switching nodes such as SW are susceptible to noise due to AC coupling with other nodes. Route the coil pattern as thick and as short as possible. Provide lines connected to FB far from the SW nodes. Place the output capacitor away from the input capacitor in order to avoid the effect of harmonic noise from the input. Power Dissipation When designing the PCB layout and peripheral circuitry, sufficient consideration must be given to ensure that the power dissipation is within the allowable dissipation curve. Allowable power dissipation: Pd [W] 4.0 2 (1) 4-layer board (surface heat dissipation copper foil 5505 mm ) 3.0 2.0 (copper foil laminated on each layer) θJA = 47.0°C/W 2 (2) 4-layer board (surface heat dissipation copper foil 6.28 mm ) (copper foil laminated on each layer) θJA = 70.62°C/W (3) 1-layer board (surface heat dissipation copper foil 6.28 mm2) θJA = 201.6°C/W (4) IC only θJA = 462.9°C/W (1)2.66 W (2)1.77 W (3)0.62 W (4)0.27 W 0 0 25 50 75 100 105 125 150 Ambient temperature: Ta [°C] Figure 53. Thermal Derating Characteristics (VQFN016V3030) www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 24/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV I/O equivalence circuit(s) 6. FB 7. FREQ 8. MODE 9. SS 10.11.12. SW 13. BOOT PVIN BOOT PVIN BOOT SW SW 14. PGD 15. EN EN 30kΩ 70kΩ www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 25/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded, the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 26/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Operational Notes – continued 11. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 12. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Figure 54. Example of monolithic IC structure 13. Ceramic Capacitor When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. 14. Area of Safe Operation (ASO) Operate the IC such that the output voltage, output current, and power dissipation are all within the Area of Safe Operation (ASO). 15. Thermal Shutdown Circuit(TSD) This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always be within the IC’s power dissipation rating. If however the rating is exceeded for a continued period, the junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below the TSD threshold, the circuits are automatically restored to normal operation. Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat damage. 16. Over Current Protection Circuit (OCP) This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should not be used in applications characterized by continuous operation or transitioning of the protection circuit. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 27/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Ordering Information B D 9 B 3 Part Number 0 0 M U Package VQFN016N3030 V - E2 Packaging and forming specification E2: Embossed tape and reel Marking Diagrams VQFN016V3030 (TOP VIEW) Part Number Marking D 9 B 3 0 0 LOT Number 1PIN MARK www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 28/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Physical Dimension, Tape and Reel Information Package Name VQFN016V3030 <Tape and Reel information> Tape Embossed carrier tape Quantity 3000pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 ) ∗ Order quantity needs to be multiple of the minimum quantity. 29/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Datasheet BD9B300MUV Revision History Date Revision 23.MAY.2014 001 Changes New Release www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 30/30 TSZ02201-0J2J0AJ00410-1-2 23.May.2014 Rev.001 Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) intend to use our Products in devices requiring extremely high reliability (such as medical equipment , transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-GE © 2013 ROHM Co., Ltd. All rights reserved. Rev.003 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-GE © 2013 ROHM Co., Ltd. All rights reserved. Rev.003 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001