Datasheet

Signal processing unit for PSD module
C10460
Specifically dedicated for PSD module
The C10460 is a signal processing unit specifically design to convert the output from a PSD module C10443 series (except for
the C10443-06) into position signals.
Position signals are output as both analog and digital signals. In case of analog output, connecting the output connector
to a voltmeter shows an output voltage that directly represents the position information (The output voltage indicates a
position from the center of the PSD, 1 V=1 mm). While, digital output allows serial connection (RS-232C) to a PC. Position
information can be easily loaded into a PC via the sample software that comes with the unit.
Features
Applications
Both analog and digital outputs
Analog output: Output voltage directly represents the
position information.
Digital output: High-resolution digital output (16-bit)
Optical axis alignment
AC adapter (+12 V) operation
Range finder
Two-dimensional measurement
Three-dimensional measurement
Length measurement
Supplies power to PSD modules
Liquid level sensors
Distortion measurement
Displacement sensors
Absolute maximum ratings (Ta=25 °C unless otherwise noted)
Parameter
Supply voltage
Input voltage
Output voltage
Operating temperature*1
Storage temperature*1
Symbol
Vcc
Vin
Vout
Topr
Tstg
Min.
-13
-15
0
-10
Max.
+18
+13
+15
+40
+60
Unit
V
V
V
°C
°C
*1: No dew condensation
When there is a temperature difference between a product and the surrounding area in high humidity environment, dew
condensation may occur on the product surface. Dew condensation on the product may cause deterioration in characteristics and
reliability.
Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the
product within the absolute maximum ratings.
Specifications (Ta=25 °C, Vcc=+12 V, unless otherwise noted)
Parameter
Supply voltage
Input voltage
Current consumption
Symbol
Vcc
Vin
Icc
Min.
+9
-12
-
Typ.
+12
200
www.hamamatsu.com
Max.
+18
0
-
Unit
V
V
mA
1
Signal processing unit for PSD module
C10460
Analog section
Parameter
Output amplitude voltage
Output noise voltage
Offset voltage
Position detection error
Position resolution*2
Cutoff frequency (-3 dB)
Symbol
Vout
Vn
Vos
E
∆R
fc
Min.
-10
-5
-
Typ.
5
±3
5
13.5
Max.
+10
+5
-
Unit
V
mVp-p
mV
%
μm
kHz
*2: Reference value. Values may vary depending on operating environment.
Digital section
Parameter
Signal conversion time - mode 1*3
Signal conversion time - mode 2*4
Output form
Symbol
Tr1
Tr2
-
Min.
Typ.
Max.
2
5
Conforms to RS-232C (position signals, light level monitor), 16-bit
Unit
ms
ms
-
*3: Communication parameter 115200 bps/8-bit/Non-parity/1 stop bit
*4: Communication parameter 38400 bps/8-bit/Non-parity/1 stop bit
Applicable PSD modules
∙ C10443-01
∙ C10443-02
∙ C10443-03
∙ C10443-04*5
Note: The C10443-06 is not supported.
*5: When used in combination with C10460, the cutoff frequency is 13.5 kHz.
Connection example
AC adapter*
PSD module
C10443
Secure with optical
bench rod, etc.
Cable for
analog output*
Connection cable
for PSD module*
Voltmeter,
oscilloscope, etc.
Signal processing
unit for PSD module
C10460
RS232C cable
PC
* Accessories of C10460
KACCC0349EC
2
Signal processing unit for PSD module
C10460
Sample software (accessory)
Sample software acquires and displays position data as
numerical values and on an XY graph, as well as recording
the data.
· Acquisition count: 1 to 300000
· Acquisition interval
Mode 1: 2 ms to 120000 ms (in 2 ms intervals)
Mode 2: 5 ms to 300000 ms (in 5 ms intervals)
Compatible OS:
Microsoft® Windows® 7 Professional SP1 (32/64-bit)*6
Microsoft® Windows® 8 Professional (32/64-bit)*6
*6: Microsoft Windows is either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
C10460
PSD SIGNAL PROCCESING UNIT
12V
2ms
DIGITAL
ANALOG
DIGITAL OUTPUT
C10443-01
C10443-02
C10443-03
±10V RANGE
30 ± 1
RS-232C
HEAD
150 ± 1
Lo OK Hi
ANALOG OUTPUT
LIGHT
LEVEL
Connector for
PSD module
HR10A-10R-10S
(Hirose Electric
10-pin, female)
5ms
MODE
ON
POWER
OFF
PSD SIGNAL PROCCESING UNIT C10460
DC INPUT
1A
Dimensional outline (unit: mm)
Connector for
analog output
DX10GM-20SE
(Hirose Electric
20-pin, female)
Connector for
digital output
JEY-9S-1A3A90
(JST, 9-pin, female)
100 ± 1
KACCA0195EE
3
Signal processing unit for PSD module
C10460
Accessories (unit: mm)
·
·
·
·
Instruction manual
Sample software CD-ROM
AC adapter
Cable for PSD module
1000 ± 50
Connector HR10A-10P-10P
(Hirose Electric, 10-pin, male)
Connector HR10A-10P-10S
(Hirose Electric, 10-pin, female)
KACCA0196JA
· Cable for analog output (no connector on one end)
1000 ± 50
Connector 10120-6000EL (Sumitomo 3M, 20-pin, male)
KACCA0197JA
Note: RS232C cable is not supplied with C10460. Use a commercially available cable with 9-pin D-sub connectors. (male - female, straight)
Related information
www.hamamatsu.com/sp/ssd/doc_en.html
Precautions
∙ Disclaimer
Information described in this material is current as of June, 2016.
Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the
information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always
contact us for the delivery specification sheet to check the latest specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that
one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741
China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866
Cat. No.KACC1135E07 Jun. 2016 DN
4