SFP www.vishay.com Vishay Electro-Films Thin Film Top-Contact Resistor with Part Mark FEATURES • • • • • • • • • • Product may not be to scale The SFP series single-value resistor chips offer a small size, wide ohmic value range and excellent power capacity. The SFPs are part marked with resistance value allowing user the ability to visually determine the resistance value of the chip. The SFPs are manufactured using Vishay Electro-Films (EFI) sophisticated thin film equipment and manufacturing technology. The SFPs are 100 % electrically tested and visually inspected to MIL-STD-883, method 2032 class H or K. Wire bondable Part marked - 5 digits Small size: 0.022 inches square Case: 0202 Resistance range: 1 to 1 M DC power rating: 250 mW Oxidized silicon substrate for good power dissipation Resistor material: Tantalum nitride, self passivating Moisture resistant Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS Vishay EFI SFP small resistor chips are widely used in hybrid packages where space is limited and chip value marking is important for identification. The die is part marked with the resistance value. Wire bonding is made to the two pads on the top of the chip. TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES PARAMETER VALUE Total Resistance Range 1 to 1M ± 0.1, ± 0.5, ± 1 % ± 25, ± 50, ± 100, ± 250 ppm/°C Standard Tolerances TCR UNIT Tightest Standard Tolerance Available 1% 0.5 % 0.1 % ± 25 ppm/°C ± 50 ppm/°C ± 100 ppm/°C ± 250 ppm/°C 1 Ω 10 Ω 30 Ω 100 Ω 200 k Ω 430 k Ω 620 k Ω 1 MΩ STANDARD ELECTRICAL SPECIFICATIONS PARAMETER VALUE UNIT Noise, MIL-STD-202, Method 308 100 - 250 k < 100 or > 251 k - 35 typ. - 20 typ. dB Moisture Resistance, MIL-STD-202, Method 106 ± 0.5 max. R/R % Stability, 1000 h, + 125 °C, 125 mW ± 0.25 max. R/R % - 55 to + 125 °C Thermal Shock, MIL-STD-202, Method 107, Test Condition F ± 0.25 max. R/R % High Temperature Exposure, + 150 °C, 100 h ± 0.5 max. R/R % Operating Temperature Range Dielectric Voltage Breakdown Insulation Resistance Operating Voltage 200 V 1012 min. 100 V max. V 0.250 W ± 0.25 max. R/R % DC Power Rating at + 70 °C (Derated to zero at + 175 °C) 5 x Rated Power Short-Time Overload, + 25 °C, 5 s Note • Values above 1M available Revision: 04-Mar-13 1 Document Number: 61000 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFP www.vishay.com Vishay Electro-Films DIMENSIONS in inches 0.005 PART MARK TYPICAL RANGE < 30 Ω PART MARK PART MARK TYPICAL RANGE 1 kΩ to 1 MΩ TYPICAL RANGE 200 Ω to 1 kΩ TYPICAL RANGE 30 Ω to 199 Ω 0.022 PART MARK 0.018 PART MARK PART MARK PART MARK PART MARK 0.004 SCHEMATIC STANDARD MARKING - 5 DIGITS XXXX X Four significant digits of value Multiplier C = 0.001 B = 0.01 A = 0.1 0=0 1 = 10 2 = 100 3 = 1000 MECHANICAL SPECIFICATIONS PARAMETER VALUE Chip Size 0.022" x 0.022" ± 0.003" (0.558 mm x 0.558 mm ± 0.05 mm) Chip Thickness 0.010" ± 0.002" (0.254 mm ± 0.05 mm) Chip Substrate Material Oxidized silicon, 10 kÅ minimum SiO2 Resistor Material Tantalum nitride, self-passivating Bonding Pad Size 0.004" x 0.004" (0.10 mm x 0.10 mm) Number of Pads 2 Pad Material 25 kÅ minimum aluminum (Au optional) Backing None, lapped semiconductor silicon (Au optional) GLOBAL PART NUMBER INFORMATION Global Part Number: SFP50000FKANHWS Global Part Number Description: SFP 5K 1 % 100 ppm/°C Al None H WS S F P MODEL RESISTANCE SFP First 4 digits are significant figures of resistance 22 x 22 size Ta2N on Silicon w/ part mark Revision: 04-Mar-13 5 0 0 RESISTANCE MULTIPLIER CODE TOLERANCE CODE (%) C = 0.001 B = 0.01 A = 0.1 0=1 1 = 10 2 = 100 3 = 1000 B = 0.1 C = 0.25 D = 0.5 F = 1.0 G = 2.0 J = 5.0 K = 10.0 0 0 TCR (ppm/°C) E = ± 25 C = ± 50 K = ± 100 M = ± 250 F K A N H W S TERMINATION BACK METAL VISUAL CLASS PACKAGING CODE G = Au A = Al G = Au N = None H = Class H K = Class K WS = Waffle pack 100 min., 1 mult 2 Document Number: 61000 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000