TCLT1600 Datasheet

TCLT1600
www.vishay.com
Vishay Semiconductors
Optocoupler, Phototransistor Output, AC Input,
SOP-4L, Long Mini-Flat Package
FEATURTES
3
4
• Low profile package
• Extra low coupling capacity - typical 0.2 pF
• High common mode rejection
• AC input
1
• Creepage current resistance according to
VDE 0303/IEC 60112 comparative tracking
index: CTI ≥ 175
2
17295-5
• Creepage distance > 8 mm
DESCRIPTION
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
The TCLT1600 consists of a phototransistor optically
coupled to 2 gallium arsenide infrared-emitting diodes in an
SOP 4-pin wide body package.
APPLICATIONS
• Switch-mode power supplies
• Line receiver
AGENCY APPROVALS
• Computer peripheral interface
• UL1577, file no. E76222
• Microprocessor system interface
• CSA 22.2 bulletin 5A, double protection
• Reinforced isolation provides circuit protection against
electrical shock (safety class II)
• DIN EN 60747-5-2 (VDE 0884)/DIN EN 60747-5-5
(pending), available with option 1
• Circuits for safe protective separation against electrical
shock according to safety class II (reinforced isolation):
- for appl. class I to IV at mains voltage ≤ 300 V
- for appl. class I to III at mains voltage ≤ 600 V
according to DIN EN 60747-5-2 (VDE 0884)
• BSI IEC 60950; IEC 60065
ORDERING INFORMATIONS
SOP-4L
T
C
L
T
1
6
0
0
10.2 mm
PART NUMBER
AGENCY CERTIFIED/PACKAGE
CTR (%)
UL, cUL, VDE, BSI
80 to 300
SOP-4L, miniflat, long
TCLT1600
Document Number: 83517
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Rev. 2.5, 13-Oct-15
TCLT1600
www.vishay.com
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
tp ≤ 10 μs
IF
± 60
mA
IFSM
± 1.5
A
Pdiss
100
mW
Tj
125
°C
Collector emitter voltage
VCEO
70
V
Emitter collector voltage
VECO
7
V
IC
50
mA
INPUT
Forward current
Forward surge current
Power dissipation
Junction temperature
OUTPUT
Collector current
Collector peak current
tp/T = 0.5, tp ≤ 10 ms
Power dissipation
ICM
100
mA
Pdiss
150
mW
Tj
125
°C
Junction temperature
COUPLER
Total power dissipation
Ptot
250
mW
Operating ambient temperature range
Tamb
-55 to +100
°C
Storage temperature range
Tstg
-55 to +125
°C
Soldering temperature (1)
Tsld
260
°C
Notes
• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
(1) Wave soldering three cycles are allowed. Also refer to “Assembly Instruction” (www.vishay.com/doc?80054).
ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
INPUT
Forward voltage
IF = ± 50 mA
VF
-
1.25
1.6
V
VR = 0 V, f = 1 MHz
Cj
-
50
-
pF
Collector emitter voltage
IC = 1 mA
VCEO
70
-
-
V
Emitter collector voltage
IE = 100 μA
VECO
7
-
-
V
VCE = 20 V, IF = 0 A
ICEO
-
10
100
nA
Collector emitter saturation voltage
IF = ± 10 mA, IC = 1 mA
VCEsat
-
-
0.3
V
Cut-off frequency
VCE = 5 V, IF = ± 10 mA,
RL = 100 Ω
fc
-
110
-
kHz
f = 1 MHz
Ck
-
0.3
-
pF
Junction capacitance
OUTPUT
Collector ermitter leakage current
COUPLER
Coupling capacitance
Note
• Minimum and maximum values are tested requierements. Typical values are characteristics of the device and are the result of engineering
evaluations. Typical values are for information only and are not part of the testing requirements.
CURRENT TRANSFER RATIO (Tamb = 25 °C, unless otherwise specified)
PARAMETER
IC/IF
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
VCE = 5 V, IF = ± 5 mA
CTR
80
-
300
%
Document Number: 83517
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Rev. 2.5, 13-Oct-15
TCLT1600
www.vishay.com
Vishay Semiconductors
SAFETY AND INSULATION RATINGS
PARAMETER
Partial discharge test voltage - routine test
Partial discharge test voltage lot test (sample test)
TEST CONDITION
SYMBOL
VALUE
UNIT
100 %, ttest = 1 s
Vpd
2
kV
tTr = 60 s, ttest = 10 s,
(see figure 2)
VIOTM
8
kV
Vpd
1.68
kV
Isolation test voltage (RMS)
Insulation resistance
VISO
5000
VRMS
VIO = 500 V
RIO
1012
Ω
VIO = 500 V, Tamb = 100 °C
RIO
1011
Ω
VIO = 500 V, Tamb = 150 °C
(construction test only)
RIO
109
Ω
Isi
130
mA
PSO
265
mW
Forward current
Power dissipation
Rated impulse voltage
VIOTM
8
kV
Tsi
150
°C
Clearance distance
8.00
mm
Creepage distance
8.00
mm
Insulation distance (internal)
0.40
mm
Safety temperature
Note
• According to DIN EN 60747-5-2 (VDE 0884) (see figure 2). This optocoupler is suitable for safe electrical isolation only within the safety
ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits.
VIOTM
300
t1, t2
t3 , t4
ttest
tstres
Phototransistor
PSO (mW)
250
200
= 1 s to 10 s
=1s
= 10 s
= 12 s
Vpd
150
VIOWM
VIORM
100
IR-diode
ISI (mA)
50
0
0
0
25
50
75
100
125
150
TSI - Safety Temperature (°C)
Fig. 1 - Derating Diagram
13930
t3 ttest t4
tTr = 60 s
t1
t2
t stres
t
Fig. 2 - Test Pulse Diagram for Sample Test according to
DIN EN 60747-5-2; IEC60747-5-5
SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
Delay time
VS = 5 V, IC = 2 mA, RL = 100 Ω,
(see figure 3)
td
-
3
-
μs
Rise time
VS = 5 V, IC = 2 mA, RL = 100 Ω,
(see figure 3)
tr
-
3
-
μs
Turn-on time
VS = 5 V, IC = 2 mA, RL = 100 Ω,
(see figure 3)
ton
-
6
-
μs
Storage time
VS = 5 V, IC = 2 mA, RL = 100 Ω,
(see figure 3)
ts
-
0.3
-
μs
Fall time
VS = 5 V, IC = 2 mA, RL = 100 Ω,
(see figure 3)
tf
-
4.7
-
μs
Turn-off time
VS = 5 V, IC = 2 mA, RL = 100 Ω,
(see figure 3)
toff
-
5
-
μs
Turn-on time
VS = 5 V, IF = 10 mA, RL = 1 kΩ,
(see figure 4)
ton
-
9
-
μs
Turn-off time
VS = 5 V, IF = 10 mA, RL = 1 kΩ,
(see figure 4)
toff
-
10
-
μs
Document Number: 83517
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Rev. 2.5, 13-Oct-15
TCLT1600
www.vishay.com
IF
Vishay Semiconductors
+5V
IF
0
I C = 2 mA; adjusted through
input amplitude
R G = 50 Ω
tp
= 0.01
T
t p = 50 µs
Channel I
Oscilloscope
R L = 1 MΩ
C L = 20 pF
Channel II
50 Ω
100 Ω
95 10804
Fig. 3 - Test Circuit, Non-Saturated Operation
IF
+5V
I F = 10 mA
0
IC
R G = 50 Ω
tp
= 0.01
T
t p = 50 µs
Channel I
Channel II
50 Ω
Oscilloscope
R L ≥ 1 MΩ
C L ≤ 20 pF
1 kΩ
95 10843
Fig. 4 - Test Circuit, Saturated Operation
IF
0
tp
IC
t
100 %
90 %
10 %
0
tr
td
t on
tp
td
tr
t on (= td + tr)
Pulse duration
Delay time
Rise time
Turn-on time
ts
tf
t off
ts
tf
t off (= ts + tf)
t
Storage time
Fall time
Turn-off time
96 11698
Fig. 5 - Switching Times
Document Number: 83517
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Rev. 2.5, 13-Oct-15
TCLT1600
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS (in millimeters)
2.30 max.
4.10 max.
10.20
3.80
+ 0.30
- 0.40
0.20
2.00
+ 0.10
- 0.05
7.50 ± 0.20
0.10
Seating plane
0.45 ± 0.1
0.70
+ 0.30
- 0.40
2.54 nom.
4
3
2.54
Possible footprint
0.90
8.20
1
22533
10.80
technical drawings
according to DIN
specifications
2
Pin no. 1 identification
PACKAGE MARKING
TCLT1600
V YWW 68
TAPE AND REEL DIMENSIONS (in millimeters)
Ø 1.55
2.7
4
2
0.3
7.5
Tape slot
in core
1.75
ESD sticker
10.6
16
330
(13")
5°
4.25
8
Ø 1.6
Regular, special
or bar code label
17999
Fig. 6 - Reel Dimensions (3000 units per reel)
2.3
Direction of pulling out
technical drawings
according to DIN
specification
22662
Fig. 7 - Tape Dimensions
Document Number: 83517
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Rev. 2.5, 13-Oct-15
TCLT1600
www.vishay.com
Vishay Semiconductors
SOLDER PROFILE
HANDLING AND STORAGE CONDITIONS
ESD level: HBM class 2
300
255 °C
240 °C
217 °C
250
Temperature (°C)
max. 260 °C
245 °C
Floor life: unlimited
Conditions: Tamb < 30 °C, RH < 85 %
Moisture sensitivity level 1, according to J-STD-020
200
max. 30 s
150
max. 100 s
max. 120 s
100
max. ramp down 6 °C/s
50
max. ramp up 3 °C/s
0
0
19841
50
100
150
200
250
300
Time (s)
Fig. 8 - Lead (Pb)-free Reflow Solder Profile
according to J-STD-020
Document Number: 83517
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Rev. 2.5, 13-Oct-15
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000