PFCU390HPx07

PFCU390HPx07
Power Factor Correction
Half-brick
Power Factor Correction Module
85-264Vrms*
Input Voltage
47 - 63Hz / 360 - 800Hz
Input Frequency
390Vdc
700W
Output Voltage
Output Power
The PFCQor® Power Factor Correction module
is an essential building block of an AC-DC
power supply. Used in conjunction with a
hold-up capacitor, SynQor’s high efficiency DCDC converters and SynQor’s AC line filter, the
PFCQor will draw a nearly perfect sinusoidal
current (PF>0.99) from a single phase AC input.
The PFCQor is capable of being paralleled for
higher power levels. The module is supplied
completely encased to provide protection from
the harsh environments seen in many industrial
and transportation environments.
•
•
•
•
•
Universal input voltage range: 85-264Vrms
Universal input frequency range: 45 - 65Hz / 360 - 800Hz
Up to 700W output power
≥0.99 Power Factor
High efficiency: >96% (230Vrms)
>94% (115Vrms)
• Internal inrush current limit
• Auxiliary 10V bias supply
• Can be paralleled with current sharing
• Compatible with SynQor DC-DC converters & AC line filters
Mechanical Features
•
•
•
•
Industry standard half-brick pin-out
Size: 2.386” x 2.486” x 0.512” (60.6 x 63.1 x 13.0 mm)
Total weight: 4.9 oz (139 g)
Flanged baseplate version available
Control Features
•
•
•
•
•
PFC Enable
Load Enable (also: Power Out Good signal)
AC Power Good Signal
Clock synchronization
Output current monitor / Active current sharing
Protection Features
•
•
•
•
Input current limit and auto-recovery short circuit protection
Auto-recovery input under/over-voltage protection
Auto-recovery output over-voltage protection
Auto-recovery thermal shutdown
Compliance Features
(With SynQor AC Line Filter)
• EN55011 and EN55022, FCC
• EN61000-3-2
• EN61000-3-3
• EN61000-4-4/5/6/11
Safety Features
•
•
•
•
•
Contents
Input/Output to baseplate isolation 2150Vdc
UL 60950-1:2007
CAN/CSA-C22.2 No. 60950-1:2007
EN60950-1/A12:2011
CE Marked
Product # PFCU390HPx07
Up to 96%
Full Load Efficiency
SRS-G
0HPC07
CTION
PFCU39 ACTOR CORRE
F
700W
R
c
E
d
V
W
0
O
9
P
Vrms 3
100-240 360 - 800Hz
z/
47 - 63H
* The label shows a narrower input voltage range to be consisitent with labeling
requirements of IEC60950-1, Section 1.7
Operational Features
≥0.99
Power Factor
Phone 1-888-567-9596
Page No.
Technical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Standards & Qualification Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Application Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mechanical Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 1
Technical Specification
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
Typical Application of the PFC Module
F1
MOV1
F2
L1IN
L1
L1OUT
SynQor
AC Line Filter
+Vout
CLK Sync
SynQor
PFC Module
TVS1
IMON
GND
L2/NIN
+Vout
ON/
OFF
+Sense
SynQor
DC-DC
Converter
Trim
CHold-Up
Load ENA
PFC ENA
L2/NOUT
AC Good
+VIN
AUX
L2/N
-Sense
-Vout
-Vout
-VIN
CY1
ENABLE
F3
CY2
+Vout
+VIN
ON/
OFF
●
●
●
+Sense
SynQor
DC-DC
Converter
Trim
-Sense
-VIN
F1:
-Vout
CY3
10A / 250V Fuse
CY4
MOV1, TVS1: Must prevent peak voltage from exceeding 575V during all transients.
F2, F3 :
Use fuse recommended in converter specification
CHold-Up:
100 - 1,000 μF (Dependent on Power Level and Line Frequency)
CY1-Y4:
See “EMI Considerations” in application notes
Isolated AC Good
Suggested Parts:
F1:
250VAC, 10A; Littelfuse 0216010.MXEP
MOV1:
300VAC, 60J; EPCOS S10K300E2
TVS1:
400V, 3J; Use two VISHAY 1.5KE200CA devices connected in series
CHold-Up:
450V, 390uF; United Chemi-Con ELXS451VSN391MR50S
CY1, CY3:
3.3nF, 500VAC; Vishay VY1332M59Y5UQ6TV0
CY2, CY4:
10nF, 300VAC; Vishay VY2103M63Y5US63V7
Typical Application of the PFCQor module to create a multiple-ouput AC-DC Power Supply
Product # PFCU390HPx07
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 2
Technical Specification
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
PFCU390HPx07 Electrical Characteristics
Operating conditions of 115Vrms, 60Hz input, 700W output, 390uF bulk capacitance, and baseplate temperature = 25°C unless otherwise noted; full
operating baseplate temperature range is -40 °C to +100 °C with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max.
Units
Notes & Conditions
ABSOLUTE MAXIMUM RATINGS
Input Voltage (L1 to L2/N)
Operating
Continuous
264
Vrms
375
Vpk
Transient (≤100ms )
290
Vrms
410
Vpk
Non-Operating
400
Vrms
575
Vpk
Isolation Voltage (Input / Output to Baseplate)
2150
Vdc
Operating Temperature
-40
100
°C
Baseplate temperature
Storage Temperature
-45
125
°C
Voltage at AC GOOD and LOAD ENA pins
-0.3
16
V
Relative to Vout- pin
Current drawn from AUX pin
0
10
mADC
Voltage at PFC enable pin
-2
575
V
Relative to Vout- pin
Voltage at CLK SYNC In
-2
5.5
V
Relative to Vout- pin
INPUT CHARACTERISTICS (L1 to L2/N)
Operating Input Voltage Range
AC Input Continuous
85
264
Vrms
AC Input 100ms Transient
40
290
Vrms
Available output power reduced when <85 Vrms
Input Under-Voltage Lockout
30
Vrms
>1s Duration
Operating Input Frequency
50/60Hz
45
65
Hz
400Hz
360
800
Hz
Power Factor of AC Input Current
0.99
50/60Hz
0.97
400Hz, min 400W output
Total Harmonic Distortion of AC Input Current
3
%
Inrush of AC Input Current
10
A
25
A
230V, 400Hz
Enabled AC Input Current (no load)
50
80
mArms
Disabled AC Input Current
30
50
mArms
Maximum Input Power
775
W
Vin >85Vrms
Arms
Maximum Input Current
9.5
85 VAC in
OUTPUT CHARACTERISTICS
Output Voltage Set Point
385
390
395
Vdc
Vin <240 Vrms, see figure 10
Output Voltage Regulation
Over Line
±0.3
%
Vin <240 Vrms, see figure 10
Over Load
±2
%
Over Temperature
±1.5
%
Total Output Voltage Range:
Input Voltage within Continuous Range
380
395
Vdc
Vin <240 Vrms, see figure 10
Input Voltage within Transient Range
365
430
V
Input Voltage Brownout/Dropout
200
395
V
See application section
Output Voltage Ripple and Noise
60Hz, see Note 1
Peak-to-Peak
10
V
Dependent on Hold-up capacitor
V
RMS
4
Operating Output Current Range
0
1.8
A
Output Over-Voltage Shutdown Threshold
420
460
V
Output (Hold-up) Capacitance
100
1,000
µF
See Note 2
Output Common-Mode Capacitance
20
nF
See “EMI Considerations” in application notes
Efficiency
50% Load
94
%
See Figure 1 for efficiency curve
100% Load
95
%
See Figure 1 for efficiency curve
Note 1: 300 µF electrolytic hold-up capacitor having a typical ESR of 0.5Ω. More capacitance/Lower ESR will reduce the line frequency ripple.
Note 2: The PFCQor is able to operate with a minimum of 100uF of hold-up capacitance but SynQor recommends at least 330uF if the power system
will be required to conform to lightning surge standards.
This is because the PFCQor relies on the hold-up capacitor to absorb the energy from a lightning surge.
Product # PFCU390HPx07
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 3
Technical Specification
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
PFCU390HPx07 Electrical Characteristics (continued)
Operating conditions of 115Vrms, 60Hz input, 700W output, 390uF bulk capacitance, and baseplate temperature = 25°C unless otherwise noted; full
operating baseplate temperature range is -40 °C to +100 °C with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max.
Units Notes & Conditions
DYNAMIC CHARACTERISTICS
Turn-On Transient
Start-up Inhibit Time
10
ms
Turn-On Time
2
s
Output Voltage Overshoot
0
%
ISOLATION CHARACTERISTICS (Input/output to baseplate)
Isolation Voltage
2150
V
Isolation Resistance
100
MΩ
Isolation Capacitance
100
pF
TEMPERATURE LIMITS FOR POWER DERATING CURVES
Semiconductor Junction Temperature
125
°C
Board Temperature
125
°C
Transformer Temperature
125
°C
Maximum Baseplate Temperature, Tb
100
°C
FEATURE CHARACTERISTICS
Output Precharge
Output Current
100
mA
Output Short-Circuit Withstand
indefinite
s
Free Running Switching Frequency
200
kHz
Each of 4 interleaved phases
Clock Synchronization Input (CLK SYNC)
Frequency Range
150
250
kHz
Logic Level High
2
V
Logic Level Low
0.8
V
Duty Cycle
20
80
%
PFC Enable (PFC ENA)
V
Off-State Voltage
2
On-State Voltage
0.8
Internal Pull-Up Voltage
5
Vpk
Internal Pull-Up Resistance
10
kΩ
AC Good (AC GOOD)
AC Input Voltage for AC Good
119
375
Vpk
AC Good State
0
0.4
V
AC Not Good State
15
V
Open Collector
Maximum Sink Current
300
mA
Load Enable
(also: Output Power Good) (LOAD ENA)
Enable (Good) State
0
0.4
V
Disable (Not Good) State
15
V
Open Collector
Maximum Sink Current
300
mA
Output Voltage for Load Enable (Good) State
Rising / Startup
360
V
Falling / Shutdown
200
V
Over-Temperature Trip Point
130
°C
At internal PCB
Auxiliary Bias Supply
Voltage Range (≤3 mA Load)
7
11
V
Maximum Source Current
10
mA DC
Equivalent Series Resistance
1
kΩ
RELIABILITY CHARACTERISTICS
Calculated MTBF (Telcordia) TR-NWT-000332
2.5
106 Hrs. Tb = 70°C
Calculated MTBF (MIL-217) MIL-HDBK-217F
2
106 Hrs. Tb = 70°C
Field Demonstrated MTBF
106 Hrs. See our website for details
Product # PFCU390HPx07
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 4
Technical Specification
100
60
95
50
Power Dissipation (W)
Efficiency (%)
90
85
80
75
115 Vin
230 Vin
70
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
40
30
20
115 Vin
230 Vin
10
90 Vin
90 Vin
65
0
0
100
200
300
400
500
600
700
0
100
200
Output Power (W)
300
400
500
600
700
Output Power (W)
Figure 1: Efficiency at nominal output voltage vs. load power for 90Vrms,
115Vrms and 230Vrms (60Hz) input voltage at Tb = 25°C.
Figure 2: Power dissipation at nominal output voltage vs. load power for
90Vrms, 115Vrms and 230Vrms (60Hz) input voltage at Tb = 25°C.
Figure 3: Typical Input Voltage and Current waveforms at fullrated power
(115Vrms, 60Hz) Yellow: Vin (100V/div), Green: Iin (5A/div), Timebase: (5ms/
div).
Figure 4: Typical Input Voltage and Current waveforms at full rated power
(115Vrms, 400Hz). Yellow: Vin (100V/div), Green: Iin (5A/div), Timebase:
(1ms/div).
3
2.5
Amplitude (% of fundamental current)
Amplitude (% of fundamental current)
3
PFCQor
EN 61000-3-2*
MIL-1399
2
MIL-461 CE101
1.5
1
0.5
0
PFCQor
2.5
EN 61000-3-2*
MIL-1399
2
MIL-461 CE101
1.5
1
0.5
0
1
3
5
7
9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49
1
3
Overtone #
Figure 5: Frequency spectrum of input current at full rated power (115Vrms,
60Hz).
Product # PFCU390HPx07
Phone 1-888-567-9596
5
7
9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49
Overtone #
Figure 6: Frequency spectrum of input current at full rated power (230Vrms,
60Hz).
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 5
Technical Specification
Figure 7: Output voltage with 500μF Hold-up capacitor at full rated power
(115VAC, 60Hz) Red: Vout (10V/div), Timebase: (5ms/div)
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
Figure 8: Output voltage startup waveform (115VAC, 60Hz) Red: (100V/div),
Timebase: (500ms/div)
435
800
430
700
425
600
420
Output Voltage (V)
Power Output (W)
PFCU390HPx07
500
400
85 Vac
100 Vac
300
115 Vac
200
Max
415
Typical
410
Min
405
400
395
390
>180 Vac
385
100
380
0
0
20
40
60
80
100
120
375
85
Base Plate Temperature (ºC)
Figure 9: Output power vs. baseplate temperature derating curve
Product # PFCU390HPx07
Phone 1-888-567-9596
110
135
160
185
210
235
260
285
Input Voltage (Vrms)
Figure 10: DC output voltage range vs. input voltage
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 6
Standards & Qualification Testing
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
Standards Compliance, Qualification Testing & EMC Characteristic
Parameter
Notes & Conditions
STANDARDS COMPLIANCE
UL 60950-1:2007
CAN/CSA-C22.2 No. 60950-1:2007
EN60950-1/A12:2011
CE Marked
Basic Insulation to Baseplate
Note: An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or
download from the SynQor website.
Parameter
QUALIFICATION TESTING
Life Test
Vibration
Mechanical Shock
Temperature Cycling
Power/Thermal Cycling
Design Marginality
Humidity
Solderability
# Units Test Conditions
32
5
5
10
5
5
5
15 pins
95% rated Vin and load, units at derating point, 1000 hours
10-55 Hz sweep, 0.060” total excursion, 1 min./sweep, 120 sweeps for 3 axis
100g minimum, 2 drops in x,y and z axis
-40 °C to 100 °C, unit temp. ramp 15 °C/min., 500 cycles
Toperating = min to max, Vin = min to max, full load, 100 cycles
Tmin-10 °C to Tmax+10 °C, 5 °C steps, Vin = min to max, 0-105% load
85 °C, 95% RH, 1000 hours, continuous Vin applied except 5 min/day
MIL-STD-883, method 2003
EMC CHARACTERISTICS (With SynQor AC Line Filter)
Conducted emissions
Line frequency harmonics
Voltage fluctuations
ESD air
Radiated immunity
Fast transients
Line surge immunity
Conducted immunity
Power freq. mag. field
Voltage dip immunity
Product # PFCU390HPx07
Phone 1-888-567-9596
EN55011 and EN55022, FCC PART 15
EN61000-3-2
EN61000-3-3
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
EN61000-4-8
EN61000-4-11
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 7
1
2
Application Section
B ASIC O PE RAT ION
AN D
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
F E ATU RE S
The PFCQor power factor correction module is an
essential building block of an overall high power AC-DC
power supply. As shown in Fig. A, a typical power supply
would be comprised of a SynQor AC Line Filter, a
SynQor PFCQor module, an energy storage hold-up
capacitor and one or more SynQor DC-DC converters,
depending on how many output voltages are required.
Fuses are needed in various places to meet safety
requirements.
The primary purpose of the PFCQor is to shape the input
current that is drawn from a single-phase sinusoidal AC
source into a nearly perfect sinusoidal waveform so that the
AC-DC power supply will present a very high power factor
load (PF > 0.99) to this source. In doing this wave-shaping,
the PFCQor ensures that the harmonic components of the
AC current waveform are well below the levels called for in
EN61000-3-2. The total harmonic distortion of the AC
current waveform is less than 8%.
The PFCQor accomplishes its wave-shaping task by first
rectifying the filtered AC source voltage, and then processing
the input power through a non-isolated, high-efficiency,
high-frequency “boost converter” that both gives the input
AC current its sinusoidal shape and provides a regulated DC
voltage across the hold-up capacitor.
The hold-up capacitor handles the cyclic imbalance
between the flow of energy drawn from the AC source and
the flow of energy delivered to the DC-DC converters. This
energy imbalance has a cyclic frequency twice that of the AC
source voltage (e.g. 120Hz for a 60Hz input). This relatively
low frequency makes the hold-up capacitor relatively large.
Another purpose of the hold-up capacitor is to be a source of
energy so that the DC-DC converters can continue to deliver
load power during a temporary brownout or dropout of the
AC source. A typical power supply will have sufficient holdup capacitor to give a “hold-up time” in the 20ms range, but
longer times can be achieved with yet more hold-up
capacitance.
Besides shaping the AC current waveform, the PFCQor
performs several other important functions. At start-up it
controls the level of inrush current drawn from the AC source
to charge the hold-up capacitor. It limits the DC current that
can be drawn from its output and it will shut-down if a short
circuit appears across the output. It will also shut-down if the
AC input voltage is out of its range (either too high or too low)
for too long, or if the temperature of the module is too high.
Product # PFCU390HPx07
PFCU390HPx07
Phone 1-888-567-9596
In addition, the PFCQor has several input and output control
signals that include PFC_ENABLE, LOAD_ENABLE, (which
doubles as a POWER_OUT_GOOD signal), AC_GOOD,
CLOCK SYNCHRONIZATION, and OUTPUT
CURRENT MONITOR. All of these signals are described
in more detail below. There is also an auxiliary bias supply that
can be used to power a low power control circuit at the output of
the PFCQor.
STARTUP SEQUENCE
When the AC source voltage is first applied, regardless of
whether the PFCQor is enabled or disabled through its
PFC_ENABLE pin, the PFCQor will pre-charge the output
hold-up capacitor with a current limited to approximately
100mA. This pre-charging continues until the output voltage
is within approximately 10V of the peak voltage of the AC
source. If, at this time, the PFC_ENABLE input is logically
high, and the PFCQor is therefore disabled, the PFCQor will
remain in this pre-charged state indefinitely.
NOTE: During both this pre-charging time and for whatever
time afterwards that the PFCQor remains disabled it is essential
that all the load converters connected to the output of the
PFCQor be disabled so that the total load current seen by the
PFCQor is only a small fraction of the 100mA charging current.
To help facilitate this requirement, the PFCQor’s
LOAD_ENABLE output can be used to disable the load
converters.
When the PFC_ENABLE input pin is pulled low, and after the
pre-charging is completed if it is not already, the boost converter
within the PFCQor will start operating and the PFCQor’s output
voltage will be increased to its nominal regulated value.
After this regulated voltage level is achieved, the PFCQor will
provide a logical low signal on its LOAD_ENABLE output pin.
This signal should be used to enable the load converters so that
they can begin to draw power from the PFCQor.
If the PFC_ENABLE input is de-asserted (pulled high or
allowed to float), the boost converter in the PFCQor will shut
down and the LOAD_ENABLE output pin will return to a logic
high. This will then disable the load converters.
NOTE: The voltage across the hold-up capacitor will remain
in a charged state after the PFCQor is disabled as long as the AC
source voltage is present.
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 8
4
3
Application Section
B R OW N O UT /D R OPO UT S E QU EN C E
If the AC source voltage falls below the PFCQor’s
specified continuous minimum input voltage, the
AC_Good output will de-assert (it will become a logic
high), although the PFCQor will continue to operate as
described below. This AC_Good output signal can be used
as a warning signal to permit a graceful shutdown of the
load after some period of time that depends on the size of
the hold-up capacitor.
If the AC source voltage is present but it is below its
continuous minimum input voltage limit, the PFCQor will
still draw whatever power it can (within its current limits)
from the AC source. This power may not be enough for the
total load power, in which case the hold-up capacitor will
provide the balance of the power. The voltage across the holdup capacitor will therefore drop as it discharges.
If the AC source voltage drops below its specified transient
minimum input voltage limit, the PFCQor’s boost converter
will shut down and no longer deliver power to the output.
Under this condition, all of the load power will be drawn from
the hold-up capacitor.
If and when the voltage across the hold-up capacitor drops
below its specified minimum limit, the LOAD_ENABLE
output will be de-asserted to a logic high. Besides disabling
the load converters, this condition will cause the PFCQor to
return to the beginning of the STARTUP SEQUENCE
described above.
NOTE: Regardless of what happens to the PFCQor’s
output voltage under a brownout or dropout condition, if the
AC source voltage drops below its rated under-voltage value
for 1 second or more, the PFCQor will shut down.
N OT E: During the first phase where the hold-up
capacitor is recharged (if it this phase exists) there will be an
inrush current drawn from the AC source that depends on the
details of how quickly the AC source voltage returns to its
normal operating condition.
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
C ONTROL F EATURES
Auxiliary Bias Power Supply (Pin 6):
The circuit shown below is an effective model for the
AUX bias power supply:
The purpose of the AUX power supply is to provide a low
level of power to control circuitry at the output of the
PFCQor, such as the circuits shown earlier in this section.
The AUX power supply is present and regulated
whenever the PFCQor’s output voltage is greater than
approximately 75V. The AUX bias power supply is
unspecified when PFCQor’s output voltage is less than
about 75V (it may, for instance, come and go as the
output voltage rises on its way to 75V).
PFC_ENABLE (Pin 3):
• If this input is floating or tied high the PFCQor’s boost
converter is disabled and the LOAD_ENABLE output signal
is de-asserted high.
• If this input is pulled low the PFCQor’s boost is enabled
after the pre-charger has charged the voltage across the
hold-up capacitor to within approximately 10 volts of the
peak of the AC source voltage.
AC_Good
Product # PFCU390HPx07
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 9
6
5
Application Section
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
AC_GOOD (Pin 8):
LOAD_ENABLE (also: POWER OUT
GOOD signal) (Pin 7):
PFCQor
• The AC_GOOD signal is internally pulled low whenever the
AC source voltage is within the PFCQor’s continuous
operating range for at least one cycle of the source waveform,
regardless of whether the PFCQor is enabled or disabled.
• When the LOAD_ENABLE pin is internally pulled LOW the
load converters are permitted to draw power from the
PFCQor’s output.
• When the peak of the AC source voltage is outside
thiscontinuous operating range (either too high or too low), the
AC_GOOD pin will float.
• When the LOAD_ENABLE floats all load converters should disabled.
• The AC GOOD signal is typically used with a pullup resistor
and an opto-coupler (as shown in Fig. A) to provide an isolated
signal to the load that the AC source voltage is no longer
within the specified continuous operating range. If this
condition persists, the load power can only be delivered for the
“hold-up time”, and it may therefore be desirable to have the
load gracefully shut down. The AC GOOD signal provides a
warning for this action to be taken. When the AC source
voltage returns to the specified continuous operating range, the
AC GOOD signal will re-assert after a 100 ms delay.
• The LOAD_ENABLE can be tied directly to the ON/OFF
control pins of SynQor’s DC-DC converters as shown in
Figure A.
• For loads that are not SynQor DC-DC converters and that do
not otherwise have a way to be enabled/disabled, an external
power MOSFET can be used to connect and disconnect these
loads from the PFCQor’s output based on the status of the
LOAD_ENABLE signal, as shown below.
• The AC_GOOD pin is valid whenever the AUX bias supply
power is valid (see above).
Output Current Monitor (Pin B):
• For high-side or remotely switched loads, an optoisolator can
be employed as shown below.
• The IMON signal monitors the DC average output current,
line-frequency components are removed from IMON.
• The IMON output voltage is 0V at no-load and increases
linearly to 2V at full-load.
• Any monitoring of thi s output should be accomplished with a
high input impedance sensor as this pin is also used for current
sharing, see below.
Product # PFCU390HPx07
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 10
7
8
Application Section
Clock Synchronization (Pin 2):
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
PFCQor will continue to deliver power into this overload
condition for 100 ms, after which the unit will shut down
and automatically return to the beginning of the STARTUP
SEQUENCE described above. If at any point the output
voltage falls below the peak of the AC source voltage, the
PFCQor will immediately shut down and return to the
STARTUP SEQUENCE.
Over Temperature:
• The PFCQor performs optimally with a 200kHz switching
frequency. Deviation from this frequency will result in a
reduction of maximum output power. Consult factory for details.
P ROTECTION F EATU RES
If the internal temperature of the PFCQor reaches 130°C the
PFCQor will turn off its boost converter.
The
LOAD_ENABLE output will simultaneously be de-asserted
high. When the internal temperature falls below 110°C, the
PFCQor will return to the beginning of the STARTUP
SEQUENCE described above.
E NERGY S TORAGE H OLD -U P
C APACI TOR
Input Over- & Under-Voltage:
The hold-up capacitor performs two functions:
If a brownout or dropout of the AC source voltage occurs, and
if it lasts long enough for the PFCQor’s output voltage to drop
below its specified minimum limit, the PFCQor will shut down.
Furthermore, regardless of what happens to the PFCQor’s output
voltage, if the AC source voltage drops below its rated undervoltage value for 1 second or more, the PFCQor will shut down.
After any shutdown the PFCQor will automatically return to the
beginning of the STARTUP SEQUENCE described above.
Output Over -Voltage:
If the output voltage exceeds its specified maximum limit, the
PFCQor’s boost converter will shutdown. However, under
this condition the PFCQor’s pre-charge circuit will continue
to deliver 100mA of current to the output whenever the AC
source voltage is higher than the dc output voltage. Care
must be taken to insure this condition does not allow the
output voltage to rise high enough to damage the PFCQor
or the load converters.
Output Current Limit & Short-Circuit
Shutdown:
If the PFCQor’s output is overloaded such that its output
current limit becomes activated, the output voltage will fall as
the excess load current discharges the hold-up capacitor. The
Product # PFCU390HPx07
Phone 1-888-567-9596
• It handles the cyclic imbalance between the flow of energy
drawn from the AC source and the flow of energy delivered to
the DC-DC converters. In doing so, the voltage across the
hold-up capacitor has a ripple at a frequency twice that of the
AC source voltage (e.g. 120Hz for a 60Hz input). The larger
the hold-up capacitor, or the higher the frequency of the AC
source, the smaller this ripple will be.
• It provides a source of energy so that the DC-DC converters
can continue to deliver load power during a temporary
brownout or dropout of the
AC source. The larger the
hold-up capacitor the longer it can provide this energy. Often
it will be made large enough to allow the load to be gracefully
shutdown after the AC source has been outside of its normal
range for a set amount of time. A typical “hold-up time”
would be in the 20 ms range for a 50/60 Hz system.
The total energy stored in a hold-up capacitor having
capacitance C at any given voltage V is:
E = ½CV 2
The amount of energy, ∆E, which can be drawn from this
capacitor depends on the capacitor’s starting voltage, Vs, and its
final voltage, Vf, where Vs is the PFCQor’s nominal regulated
output voltage and Vf is the PFCQor’s minimum output voltage
limit. This energy equals the amount of power, P, which the
DC-DC converters draw from the hold-up capacitor times the
length of time, ∆t, which it takes for the hold-up capacitor’s
voltage to drop from Vs to Vf. This energy can be equated to the
hold-up capacitance according to the following formula:
www.SynQor.com
Δ∆E = P Δ∆t = ½C(V s 2 - V f 2 )
Doc.# 005-0006254 Rev. E 04/07/2016
Page 11
10
9
Application Section
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
This formula can be rearranged to find the minimum required
value for C to provide the hold-up time desired for a given power
level (note: this power level P is not the load power, but rather the
load power divided by efficiency of the DC-DC converters):
Cmin = 2PΔ∆t ⁄ ( V s 2 - V f 2 )
For example, if we assume P = 600W, ∆t = 20ms, Vs = 390V
and Vf = 200V, then we would want a hold-up capacitance of
at least 215µF.
During the start-up sequence the PFCQor will pre-charge the
hold-up capacitor with approximately 100mA of current until it
has reached a voltage about 10V below the peak of the AC source
voltage. The time it takes for this to occur can be calculated using
the following formula:
t = CV/100mA
For example, if the AC source voltage is 230Vrms (Vpk =
325V) and the hold-up capacitor is 200µF, this length of time
will be approximately 0.6 seconds. The larger the hold-up
capacitor, the longer it will take.
After the hold-up capacitor’s voltage has reached this level, and
assuming the PFCQor has been enabled, the boost converter in
the PFCQor will quickly charge the hold-up capacitor to the
nominal regulated output voltage level.
N OT E: The PFCQor is able to operate with a minimum of
100uF of hold-up capacitance, but Synqor recommends at least
330uF if the power system will be required to conform to
lightning surge standards. This is because the PFCQor relies on
the hold-up capacitor to absorb most of the energy from a
lightning surge.
N OT E: Even though the PFCQor limits the inrush current
drawn from the AC source during its STARTUP SEQUENCE,
it will not necessarily limit this current at the end of a temporary
brownout or dropout of the AC source when the hold-up
capacitor’s voltage has not dropped below its minimum output
voltage limit. In such a condition the PFCQor will not reinitiate
a STARTUP SEQUENCE and it will therefore not limit the
current flowing through it. If the peak of the AC source voltage
is greater than the hold-up capacitor’s voltage at the end of the
brownout/dropout period, there will be a large inrush current for
one half-cycle as the hold-up capacitor’s voltage is charged up to
the peak of the AC source voltage. The larger the hold-up
capacitor the larger this inrush current will be. To keep this
inrush current within a reasonable limit, the maximum
capacitance of the hold-up capacitor is limited as specified in the
Technical Specifications table.
If it is desired to have a hold-up time longer than can be
achieved with this maximum specified hold-up capacitance, then
the circuit shown below can be used.
Product # PFCU390HPx07
Phone 1-888-567-9596
In this circuit the total hold-up capacitance is (C1 + C2), and it
can be made as large as desired as long as C1 does not exceed the
maximum capacitance specified in the Technical Specifications
table. The resistor, Rc, in series with C2 is present to limit the
current that will charge this capacitor after a temporary
brownout/dropout event. Its resistance should be large enough to
limit the charging current to a fraction of the PFCQor’s rated
output current. The diode in parallel with the resistor permits the
load converters to draw whatever energy they need from C2
without being hindered by the resistor.:
Output Ripple Considerations:
The hold-up capacitor must have a ripple current rating high
enough to withstand the ripple current generated on the
output of the PFCQor. Ripple current amplitude is
dependent only upon the total PFCQor output power, PDC,
and the operating output voltage VO. It can be calculated
using the following formula:
The AC line frequency, fac, bulk capacitance, C, operating
output voltage, and output power will determine the amplitude of
the voltage ripple present on the output of the PFCQor. It can be
calculated with:
For example, to calculate voltage and current ripple for a
PFCQor with a 700W output, 500uF hold-up capacitor, and a
60Hz fundamental AC line frequency:
In this case, the hold-up capacitor would require a minimum
ripple current rating of 1.3Arms, and the output voltage would have
a pk-pk ripple voltage of 9.6V.
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 12
11
12
PFCU390HPx07
Application Section
S AFETY N OTES
EMI CONSIDERATIONS
The output of the PFCQor is not isolated from the AC
source, and it is therefore a hazardous voltage. Care must be
taken to avoid contact with this voltage, as well as with the
AC source voltage.
The PFCQor must have a fuse in series with its AC source.
The rating for this fuse is given in the Technical Specification
table. If multiple PFCQors are paralleled, there should be a fuse
for each PFCQor.
T HERMAL C ONSIDERATION
The maximum operating base-plate temperature, TB, is 100
ºC. Refer to the thermal derating curves to see the allowable
power output for a given baseplate temperature and input
voltage. A power derating curve can be calculated for any
heatsink that is attached to the base-plate of the converter. It
is only necessary to determine the thermal resistance, RTHBA,
of the chosen heatsink between the base-plate and the
ambient air for a given airflow rate. The following formula
can then be used to determine the maximum power the
converter can dissipate for a given thermal condition:
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
To meet various conducted line emission standards,
additional Y-capacitors may be needed to attenuate commonmode noise. SynQor recommends that saftey-rated ceramic
capacitors be placed across any isolated DC-DC converters
on the output of the PFC from Vin- to Vout- and Vout- to
ground. However, the total capacitance from the PFC output
leads to earth ground should not be more than 20nF if one of
the PFC input leads is connected to earth ground. See “Typical
Application of the PFC Module” (Figure A) for a diagram and
suggested parts.
In higher power applications, multiple units can be used in
parallel as shown below.
• To balance load currents evenly between PFCQor modules, a
0.1 ohm resistor must be placed in series with Vout- on each
module. The parallel diagram below shows correct placement
of the resistors in relation to other circuitry. Resistors must be
rated to handle RMS load return current.
• PFC_ENABLE may be driven with a common signal, but a 100
ohm resistor should be placed in series with each input before
being connected to the common node.
This value of power dissipation can then be used in
conjunction with the data shown in the figures to determine the
maximum load power that the converter can deliver in the given
thermal condition.
• AUX Bias outputs can be directly connected together as shown.
AC L INE F ILTER
• The loads should only be enabled when all the individual
LOAD_ENABLE outputs have been asserted low. The circuit
An AC line filter is needed to attenuate the differential- and
common-mode voltage and current ripples created by the
PFCQor, the DC-DC converters and the load such that the
system will comply with EMI requirements. The filter also
provides protection for the PFCQor from high frequency
transients in the AC source voltage. SynQor has a family of AC
line filters that will provide these functions. It is recommended
that a metal-oxide varistor (MOV) be placed from line-to-line on
the input of the filter, and a TVS diode be placed from line-toline on the output of the filter in order to keep the PFCQor input
voltage from exceeding 575V during all transients. See Figure A
for suggested parts. If a non-SynQor AC line filter is used, the
use of an MOV on the input and a TVS diode on the output of
the filter is still recommended.
Product # PFCU390HPx07
Phone 1-888-567-9596
• AC_GOOD can drive a common signal, but a 100 ohm resistor
should be placed in series with each output before being
connected to the common node.
shown below combines the individual LOAD_ENABLE outputs
into a single master LOAD_ENABLE to achieve this
requirement.
• Active current sharing is accomplished by connecting all
IMON pins directly together. The voltage at the IMON pins
is then indicative of the average output current. Again, any
circuit used to monitor the IMON voltage should have high
input impedance.
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 13
13
14
Application Section
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
P ARALLEL D IAGRAM
Product # PFCU390HPx07
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 14
Standard Mechanical Diagram
2.486 [63.14]
2.000 [50.80]
SEATING PLANE HEIGHT
0.512 0.005
[ 13.00 0.12]
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
PIN EXTENSION
0.163
[4.14]
0.700 [17.78]
5
6
7
8
9
TOP VIEW
0.004 [0.10]
1.900 2.386
[48.26] [60.60]
0.01
[0.3]
1.900
[48.26]
4
1
0.30
[7.6]
THRU HOLE STANDOFFS
SEE NOTE 1
(4 PLCS)
1)Applied torque per screw should not exceed 6in-lb. (0.7 Nm).
2)Baseplate flatness tolerance is 0.004” (.10 mm) TIR for surface.
3)Pins 1-4, 6-8, and B are 0.040” (1.02mm) diameter, with 0.080”
(2.03mm) diameter standoff shoulders.
4)Pins 5 and 9 are 0.080” (2.03 mm) diameter with 0.125”
(3.18 mm) diameter standoff shoulders.
5)All Pins: Material - Copper Alloy; Finish - Matte Tin over Nickel plate
6)Undimensioned components are shown for visual reference only.
7)Weight: 4.9 oz (139 g)
8)Threaded and Non-Threaded options available
9)All dimensions in inches (mm).
Tolerances:
x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
unless otherwise noted.
10)Workmanship: Meets or exceeds IPC-A-610C Class II
Phone 1-888-567-9596
B
2
1
BOTTOMSIDE CLEARANCE
0.027 0.010
[ 0.69 0. 25]
NOTES
Product # PFCU390HPx07
3
0.400
0.800
1.000
1.400
[10.16]
[20.32]
[25.40]
[35.56]
PIN DESIGNATIONS
Pin
1
2
B
3
4
5
6
7
8
9
Name
L1
CLK SYNC
IMON
PFC ENA
Function
AC Line 1
Clock Synchronization Input
Output Current Monitor / Current Share
Negative Logic PFC Enable
L2/N
AC Line 2 / Neutral
-VOUT
Negative Output Voltage
AUX
Auxiliary Bias power supply
LOAD ENA Negative Logic load enable and power out good signal
AC GOOD Negative Logic AC Good signal
+VOUT
Positive Output voltage
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 15
Flanged Mechanical Diagram
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
3.150 [80.01]
0.700 [17.78]
2.950 [74.93]
2.486 [63.14]
SEATING PLANE HEIGHT
0.495 0.025
[ 12.57 0.63]
PIN EXTENSION
0.180 [4.57]
5
TOP VIEW
7
6
8
9
0.010 [0.25]
1.900
[48.26]
1.300 1.866 2.386
[33.02] [47.40] [60.60]
0.31
[7.9]
4
3
B
2
1
1
0.775 0.020
[19.69 0.50]
.130 [3.30]
SEE NOTE 1
(6 PLCS)
FLANGE THICKNESS
0.125
[3.18]
BOTTOMSIDE CLEARANCE
0.005 0.010
[ 0.13 0. 25]
0.400 [10.16]
0.800 [20.32]
1.000 [25.40]
1.400 [35.56]
NOTES
PIN DESIGNATIONS
1)Applied torque per M3 or 4-40 screw should not exceed 6in-lb. (0.7
Nm).
2)Baseplate flatness tolerance is 0.010” (.2mm) TIR for surface.
3)Pins 1-4, 6-8, and B are 0.040” (1.02mm) diameter, with 0.080”
(2.03mm) diameter standoff shoulders.
4)Pins 5 and 9 are 0.080” (2.03 mm) diameter with 0.125”
(3.18 mm) diameter standoff shoulders.
5)Other Pin extensions lengths available
6)All Pins: Material - Copper Alloy; Finish - Matte Tin over Nickel plate
7)Undimensioned components are shown for visual reference only.
8)Weight: 5.1 oz (145 g)
9)All dimensions in inches (mm).
Tolerances:
x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
unless otherwise noted.
10)Workmanship: Meets or exceeds IPC-A-610C Class II
Product # PFCU390HPx07
Phone 1-888-567-9596
Pin
1
2
B
3
4
5
6
7
8
9
Name
L1
CLK SYNC
IMON
PFC ENA
Function
AC Line 1
Clock Synchronization Input
Output Current Monitor / Current Share
Negative Logic PFC Enable
L2/N
AC Line 2 / Neutral
-VOUT
Negative Output Voltage
AUX
Auxiliary Bias power supply
LOAD ENA Negative Logic load enable and power out good signal
AC GOOD Negative Logic AC Good signal
+VOUT
Positive Output voltage
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 16
Ordering Information
Input Voltage
Family
Range
PFC
Part Numbering Scheme
Performance
Output
Thermal Design
Level
Power
C: Encased
D: Encased with
Non-threaded
H: Half-brick
P: Peta
Baseplate
07: 700W
V: Encased with
Flanged
Baseplate
Output
Voltage
U: 85-264 Vrms
PFCU390HPx07
Input:100-240Vrms
Output:390Vdc
Power:Up to 700W
Package
Size
390: 390V
Input Phases
Pin Style
Parallel
Capability
S: Single-Phase
R: 0.180”
S: Supports
Parallel
Capability
PART NUMBERING SYSTEM
ORDERING INFORMATION
The part numbering system for SynQor’s dc-dc converters follows the format
shown in the example below.
The tables below show the valid model numbers and ordering options for
converters in this product family. When ordering SynQor converters, please
ensure that you use the complete 15 character part number consisting of
the 12 character base part number and the additional characters for options.
InQor units are only available with 6/6 RoHS compliance indicated by "-G".
PFC U 3 9 0 H P C 0 7 N R S - G
6/6 RoHS
The following options must be included in place of the w x y z spaces in the
model numbers listed above.
Options
(see
Ordering Information)
Not all combinations make valid part numbers, please contact SynQor for
availability.
Output Power
Thermal Design
Performance Level
Application Notes
Package Size
A variety of application notes and technical white papers can be downloaded
in pdf format from our website.
Output Voltage
Input Voltage
RoHS Compliance: The EU led RoHS (Restriction of Hazardous
Product Family
The first 12 characters comprise the base part number and the last 3
characters indicate available options. The “-G” suffix indicates 6/6 RoHS
compliance.
Substances) Directive bans the use of Lead, Cadmium, Hexavalent
Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated
Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. This SynQor
product is 6/6 RoHS compliant. For more information please refer to
SynQor’s RoHS addendum available at our RoHS Compliance / Lead
Free Initiative web page or e-mail us at [email protected].
Contact SynQor for further information and to order:
PATENTS
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
Product # PFCU390HPx07
978-849-0600
888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
USA
Phone 1-888-567-9596
SynQor holds numerous U.S. patents, one or more of which apply to most of its power converter
products. Any that apply to the product(s) listed in this document are identified by markings on
the product(s) or on internal components of the product(s) in accordance with U.S. patent laws.
SynQor’s patents include the following:
5,999,417
6,222,742
6,545,890
6,594,159
6,731,520
6,894,468
6,896,526
6,927,987
7,050,309
7,072,190
7,085,146
7,119,524
7,269,034
7,272,021
7,272,023
7,558,083
7,564,702
7,765,687
7,787,261
8,023,290
8,149,597
8,493,751
8,644,027
9,143,042
WARRANTY
SynQor offers a two (2) year limited warranty. Complete warranty information
is listed on our website or is available upon request from SynQor.
www.SynQor.com
Doc.# 005-0006254 Rev. E 04/07/2016
Page 17