Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Qxx25xx & Qxx25xHx Series ® Description Standard type devices normally operate in Quadrants I & III triggered from AC line. Alternistor type devices only operate in quadrants I, II, & III and are used in circuits requiring high dv/dt capability. Features & Benefits t3P)4DPNQMJBOU t(MBTToQBTTJWBUFE junctions Agency Approval Agency t7PMUBHFDBQBCJMJUZVQ to 1000 V Agency File Number TO-220L, TO-218K, TO-218J & Fastpak Packages: E71639 ® Applications Excellent for AC switching and phase control applications such as heating, lighting, and motor speed controls. Main Features Symbol IT(RMS) VDRM /VRRM IGT t4VSHFDBQBCJMJUZVQ to 250 A Value Unit 25 A 1000 V 50 to 80 mA Typical applications are AC solid-state switches, industrial power tools, exercise equipment, white goods and commercial appliances. Alternistor Triacs (no snubber required) are used in applications with extremely inductive loads requiring highest commutation performance. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Schematic Symbol MT2 MT1 G ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 117 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series 25 A TRIACs 25 Amp bi-directional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls, lighting controls, and static switching relays. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Absolute Maximum Ratings – Standard Triac Symbol Parameter IT(RMS) Test Conditions RMS on-state current Qxx25R5 Qxx25N5 TC = 85°C Qxx25P5 TC = 57°C Qxx25R5 Qxx25N5 ITSM Peak non-repetitive surge current Qxx25P5 I 2t Qxx25R5 Qxx25N5 I2t Value for fusing Value Unit 25 A single half cycle; f = 50Hz; TJ (initial) = 25°C 167 single half cycle; f = 60Hz; TJ (initial) = 25°C 200 single half cycle; f = 50Hz; TJ (initial) = 25°C 220 single half cycle; f = 60Hz; TJ (initial) = 25°C 250 tp = 8.3ms Qxx25P5 A 166 A2s 260 di/dt Critical rate-of-rise of on-state current f = 60Hz; TJ =125°C 100 A/μs IGTM Peak gate current TJ = 125°C 2 A PG(AV) Average gate power dissipation TJ = 125°C Storage temperature range Tstg TJ Operating junction temperature range 0.5 W -40 to 125 °C Qxx25R5 Qxx25N5 -40 to 125 Qxx25P5 -25 to 125 Test Conditions Value Unit 25 A °C Absolute Maximum Ratings – Alternistor Triac Symbol Parameter IT(RMS) RMS on-state current Qxx25LH5 Qxx25L6 TC = 65°C Qxx25K6 Qxx25J6 TC = 85°C Qxx25RH5 Qxx25NH5 Qxx25R6 Qxx25NH6 TC = 95°C single half cycle; f = 50Hz; TJ (initial) = 25°C 208 single half cycle; f = 60Hz; TJ (initial) = 25°C 250 I2t Value for fusing tp = 8.3ms 260 A2s di/dt Critical rate-of-rise of on-state current f = 60Hz; TJ =125°C 100 A/μs IGTM Peak gate current TJ = 125°C 2 A PG(AV) Average gate power dissipation TJ = 125°C ITSM Peak non-repetitive surge current I 2t 0.5 W Storage temperature range -40 to 125 °C Operating junction temperature range -40 to 125 °C Tstg TJ A Note: xx = voltage Qxx25xx & Qxx25xHx Series 118 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Standard Triac Value Test Conditions IGT VD = 12V; RL = 60 8 VGT VGD VD = VDRM; RL = 3.3 k8 ; TJ = 125°C IH IT = 400mA (initial) dv/dt Quadrant Qxx25R5 Qxx25N5 Qxx25P5 I – II – III MAX. 50 IV TYP. 120 I – II – III MAX. 1.3 IV TYP. 2.5 ALL MIN. MAX. VD = VDRM; Gate Open; TJ = 125°C 400V 600V 800V VD = VDRM; Gate Open; TJ = 100°C 1000V MIN. (dv/dt)c (di/dt)c = 13.3 A/ms; TJ = 125°C MIN. tgt IG = 2 x IGT; PW = 15μs; IT = 35.4 A TYP. Unit mA V 0.2 V 100 50 mA 275 225 200 — 475 400 200 — V/μs 5 V/μs 4 3 μs Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Alternistor Triac Value Symbol IGT VGT Test Conditions VD = 12V; RL = 60 8 VGD VD = VDRM; RL = 3.3 k8 ; TJ = 125°C IH IT = 400mA (initial) dv/dt Quadrant Qxx25RH5 Qxx25LH5 Qxx25NH5 Qxx25R6 Qxx25L6 Qxx25NH6 Qxx25K6 Qxx25J6 50 80 Unit I – II – III MAX. I – II – III MAX. 1.3 V I – II – III MIN. 0.2 V MAX. VD = VDRM; Gate Open; TJ = 125°C 400V 600V 800V VD = VDRM; Gate Open; TJ = 100°C 1000V MIN. mA 50 100 575 500 400 600 600 475 mA V/μs — 400 (dv/dt)c (di/dt)c = 13.3 A/ms; TJ = 125°C MIN. 20 30 V/μs tgt IG = 2 x IGT; PW = 15μs; IT = 35.4 A TYP. 3 5 μs Static Characteristics Symbol VTM Value Qxx25R5 Qxx25N5 Qxx25xH5 Qxx25P5 Qxx25x6 Qxx25NH6 Test Conditions IT = 35.4A; tp = 380 μs MAX. TJ = 25°C IDRM / IRRM VDRM / VRRM TJ = 100°C TJ = 125°C 600 – 800V 1000V 1.8 1.4 10 100 20 — 500 — 1000V 1000 — 600 – 800V 2000 5000 600 – 800V MAX. Unit V μA Note: xx = voltage, x = package ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 119 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series 25 A TRIACs Symbol Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Thermal Resistances Symbol Parameter Value Qxx25R5 / Qxx25N5 Qxx25R6 / Qxx25NH6 Qxx25RH5 / Qxx25NH5 0.89 Qxx25P5 1.6 Qxx25L6 / Qxx25LH5 2.0 Qxx25K6 / Qxx25J6 1.32 Qxx25Ry 45 Qxx25L6 / Qxx25LH5 50 Junction to case (AC) RR(J-C) Unit °C/W Junction to ambient RR(J-A) °C/W Note: xx = voltage, y = sensitivity Figure 2: Normalized DC Gate Trigger Voltage vs. Junction Temperature Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature 2.5 Ratio of VGT / VGT(TJ = 25ºC) 2.0 Ratio of IGT/IGT(TJ = 25°C) 2.0 1.5 1.0 1.5 1.0 0.5 0.5 0.0 0.0 -40 -15 10 35 60 85 110 -40 125 -15 10 Figure 3: Normalized DC Holding Current vs. Junction Temperature 60 85 110 125 1.6 1.7 Figure 4: On-State Current vs. On-State Voltage (Typical) 2.0 90 Instantaneous On-state Current (iT) – Amps Ratio of IH / IH(TJ = 25ºC) 35 Junction Temperature (TJ) -- (ºC) Junction Temperature (TJ) -- (°C) 1.5 1.0 0.5 TJ = 25°C 80 70 Qxx25P5/Qxx25R6 Qxx25L6/Qxx25NH6 Qxx25K6/Qxx25J6 Qxx25RH5/Qxx25LH5 Qxx25NH5 60 50 40 30 20 Qxx25R5 Qxx25N5 10 0 0.0 -40 -15 10 35 60 85 110 0.7 125 Qxx25xx & Qxx25xHx Series 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 Instantaneous On-state Voltage (vT) – Volts Junction Temperature (TJ) -- (ºC) 120 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Figure 5: Power Dissipation (Typical) vs. RMS On-State Current Figure 6: Maximum Allowable Case Temperature vs. RMS On-State Current 130 Maximum Allowable Case Temperature (TC) - °C CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° 30 Qxx25R6 Qxx25NH6 Qxx25RH5 Qxx25NH5 120 25 Qxx25R5 Qxx25N5 Qxx25K6 Qxx25J6 110 Qxx25R5 Qxx25N5 100 20 15 Qxx25P5/Qxx25R6 Qxx25L6/Qxx25NH6 Qxx25K6/Qxx25J6 Qxx25RH5/Qxx25LH5 Qxx25NH5 10 5 0 90 Qxx25L6 Qxx25LH5 80 Qxx25P5 70 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° 60 50 0 5 10 15 20 25 0 RMS On-State Current [IT(RMS)] -- Amps 5 10 15 20 25 30 RMS On-State Current [IT(RMS)] - Amps Figure 7: Maximum Allowable Ambient Temperature vs. RMS On-State Current (TO-220 packages only) Maximum Allowable Ambient Temperature (TA) --°C 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° FREE AIR RATING 100 80 60 40 20 0 0.0 0.5 1.0 1.5 2.0 2.5 RMS On-State Current [IT(RMS)] -- Amps Figure 8: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Qxx25P5/Qxx25R6 Qxx25L6/Qxx25NH6 Qxx25K6/Qxx25J6 Qxx25RH5/Qxx25LH5 Qxx25NH5 Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 100 Qxx25R5 Qxx25N5 10 1 10 100 1000 Surge Current Duration -- Full Cycles ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 121 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series 25 A TRIACs Average On-State Power Dissipation [PD(AV)] -- Watts 35 Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Soldering Parameters Pb – Free assembly - Temperature Min (Ts(min)) Pre Heat 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Ramp-up TL tL TS(max) Ramp-do Ramp-down Preheat TS(min) tS 25 Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C time to peak temperature Physical Specifications Test 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Specifications and Conditions High Temperature Voltage Blocking Temperature Cycling Copper Alloy Biased Temp & Humidity High Temp. Storage Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Qxx25xx & Qxx25xHx Series Time Environmental Specifications Terminal Finish Lead Material tP TP Temperature Reflow Condition MIL-STD-750: Method 1040, Condition A Rated VRRM, 125°C, 1008 hours MIL-STD-750: Method 1051 -40°C to 125°C, 15-minute dwell, 100 cycles EIA/JEDEC: JESD22-A101 320VDC, 85°C, 85%RH, 1008 hours MIL-STD-750: Method 1031 150°C, 1008 hours Low-Temp Storage -40°C, 1008 hours Thermal Shock MIL-STD-750: Method 1056 0°C to 100°C, 5-minute dwell, 10-second transfer, 10 cycles Autoclave EIA/JEDEC: JESD22-A102 (Pressure Cooker Test) 121°C, 100%RH, 2atm, 168 hours Resistance to Solder Heat MIL-STD-750: Method 2031 260°C, 10 seconds Solderability ANSI/J-STD-002, Category 3, Test A Lead Bend MIL-STD-750: Method 2036, Condition E 122 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Dimensions — TO-220AB (R Package) — Non-isolated Mounting Tab AREA (REF.) 0.17 IN2 TC MEASURING POINT O A Ø E Dimension 8.13 .320 P Millimeters Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 MT2 B Inches Min 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H N K J M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). MT1 MT2 GATE C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Min Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.66 2.92 Dimensions — TO-220AB (L Package) — Isolated Mounting Tab AREA (REF.) 0.17 IN2 TC MEASURING POINT O A Ø E P Dimension 8.13 .320 B C 13.36 .526 D 7.01 .276 Inches Millimeters C 0.230 0.250 5.85 6.35 D 0.590 0.620 14.98 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.80 3.30 G 0.540 0.575 13.71 14.60 H 0.025 0.035 0.63 0.89 F R G L H K N J MT1 MT2 GATE M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 1.78 2.16 N 0.018 0.024 0.45 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.53 R 0.038 0.048 0.97 1.22 123 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series 25 A TRIACs C Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Dimensions — TO-263 (N Package) — D2Pak Surface Mount TC MEASURING POINT Dimension E MT2 7.01 .276 A 8.41 .331 S W U J K GATE MT1 8.13 .320 G H D F 2.16 .085 11.68 .460 7.01 .276 7.01 .276 16.89 .665 8.89 .350 Inches AREA: 0.11 IN2 C V B 1.40 .055 3.81 .150 Millimeters Min Max Min Max A 0.360 0.370 9.14 9.40 B 0.380 0.420 9.65 10.67 C 0.178 0.188 4.52 4.78 D 0.025 0.035 0.64 0.89 E 0.045 0.060 1.14 1.52 F 0.060 0.075 1.52 1.91 G 0.095 0.105 2.41 2.67 H 0.092 0.102 2.34 2.59 J 0.018 0.024 0.46 0.61 K 0.090 0.110 2.29 2.79 S 0.590 0.625 14.99 15.88 V 0.035 0.045 0.89 1.14 U 0.002 0.010 0.05 0.25 W 0.040 0.070 1.02 1.78 Min Max Min A 0.810 0.835 20.57 21.21 B 0.610 0.630 15.49 16.00 2.03 .080 6.60 .260 Dimensions — TO-218AC (K Package) — Isolated Mounting Tab TC Measurement Point U (diameter) B Dimension C D A F E W Gate J P MT1 MT2 M Q R G N K L Qxx25xx & Qxx25xHx Series H Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Inches Millimeters Max C 0.178 0.188 4.52 4.78 D 0.055 0.070 1.40 1.78 E 0.487 0.497 12.37 12.62 F 0.635 0.655 16.13 16.64 G 0.022 0.029 0.56 0.74 H 0.075 0.095 1.91 2.41 J 0.575 0.625 14.61 15.88 K 0.211 0.219 5.36 5.56 L 0.422 0.437 10.72 11.10 M 0.058 0.068 1.47 1.73 N 0.045 0.055 1.14 1.40 P 0.095 0.115 2.41 2.92 Q 0.008 0.016 0.20 0.41 R 0.008 0.016 0.20 0.41 U 0.164 0.165 4.10 4.20 W 0.085 0.095 2.17 2.42 124 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Dimensions — TO-218X (J Package) — Isolated Mounting Tab U (diameter) Dimension D A B C D E F G H J K L M N P R S T U V W X Y Z Tc Measurement Point A F E Z MT1 X W J Gate N R S P T M Y K G MT2 H L V Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Inches Millimeters Min Max Min Max 0.810 0.610 0.178 0.055 0.487 0.635 0.022 0.075 0.575 0.256 0.220 0.080 0.169 0.034 0.113 0.086 0.156 0.164 0.603 0.000 0.003 0.028 0.085 0.835 0.630 0.188 0.070 0.497 0.655 0.029 0.095 0.625 0.264 0.228 0.088 0.177 0.042 0.121 0.096 0.166 0.165 0.618 0.005 0.012 0.032 0.095 20.57 15.49 4.52 1.40 12.37 16.13 0.56 1.91 14.61 6.50 5.58 2.03 4.29 0.86 2.87 2.18 3.96 0.410 15.31 0.00 0.07 0.71 2.17 21.21 16.00 4.78 1.78 12.62 16.64 0.74 2.41 15.88 6.71 5.79 2.24 4.49 1.07 3.07 2.44 4.22 0.420 15.70 0.13 0.30 0.81 2.42 Dimensions — TO-3 (P Package) Fastpak — Isolated Mounting Tab Inches A Dimension B D A B C D E F G H I J K L M N O P Q R S T (MT1) T (MT2) T (Gate) U (MT1) U (MT2) U (Gate) V W MT2 H F MT1 Gate G E TC Measuring Point C I J (MT1, MT2) T U M L V W R K (Gate) 5-N S Q O P Thickness off all three copper-alloy terminals is .032" (0.81 mm). Millimeters Min Max Min Max 1.531 1.177 0.843 0.780 0.783 0.874 0.161 0.386 0.508 0.079 0.047 0.307 0.372 0.043 0.315 0.098 0.846 0.244 0.106 0.321 0.321 0.220 0.246 0.246 0.183 0.120 0.175 1.543 1.185 0.850 0.795 0.791 0.906 0.169 0.465 0.587 0.087 0.055 0.319 0.396 0.059 0.331 0.106 0.886 0.256 0.130 0.329 0.329 0.228 0.254 0.254 0.191 0.130 0.185 38.90 29.90 21.40 19.80 19.90 22.20 4.10 9.80 12.90 2.00 1.20 7.80 9.45 1.10 8.00 2.50 21.50 6.20 2.70 8.15 8.15 5.60 6.25 6.25 4.65 3.05 4.45 39.20 30.10 21.60 20.20 20.10 23.00 4.30 11.80 14.90 2.20 1.40 8.10 10.05 1.50 8.40 2.70 22.50 6.50 3.30 8.35 8.35 5.80 6.45 6.45 4.85 3.30 4.70 Maximum torque to be applied to mounting tab is 8 in-lbs (0.904Nm). ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 125 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series 25 A TRIACs C B Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Product Selector Part Number Voltage Gate Sensitivity Quadrants Package 400V 600V 800V 1000V I - II - III IV Qxx25R5 X X X X 50 mA 120 mA (TYP) TO-220R Qxx25N5 X X X X 50 mA 120 mA (TYP) TO-263 D2-Pak X X 50 mA 120 mA (TYP) Fastpak Qxx25P5 Qxx25RH5 X X X 50 mA TO-220R Qxx25LH5 X X X 50 mA TO-220L Qxx25NH5 X X X 50 mA TO-263 D2-Pak Qxx25R6 X X X X 80 mA TO-220R Qxx25L6 X X X X 80 mA TO-220L Qxx25NH6 X X X X 80 mA TO-263 D2-Pak Qxx25J6 X X X Qxx25K6 X X X X 80 mA TO-218X 80 mA TO-218AC Packing Options Part Number Marking Weight Packing Mode Base Quantity Qxx25R5 Qxx25R5 2.20g Bulk 500 Qxx25R5TP Qxx25R5 2.20g Tube 500 (50 per tube) Qxx25N5TP Qxx25N5 1.60g Tube 500 (50 per tube) Qxx25N5RP Qxx25N5 1.60g Embossed Carrier 500 Qxx25RH5 Qxx25RH5 2.20g Bulk 500 Qxx25RH5TP Qxx25RH5 2.20g Tube 500 (50 per tube) Qxx25LH5 Qxx25LH5 2.20g Bulk 500 Qxx25LH5TP Qxx25LH5 2.20g Tube 500 (50 per tube) Qxx25NH5TP Qxx25NH5 1.60g Tube 500 (50 per tube) Qxx25NH5RP Qxx25NH5 1.60g Embossed Carrier 500 Qxx25P5 Qxx25P5 21.4g Bulk 200 Qxx25R6 Qxx25R6 2.20g Bulk 500 Qxx25R6TP Qxx25R6 2.20g Tube 500 (50 per tube) Qxx25L6 Qxx25L6 2.20g Bulk 500 Qxx25L6TP Qxx25L6 2.20g Tube 500 (50 per tube) Qxx25NH6TP Qxx25NH6 1.60g Tube 500 (50 per tube) Qxx25NH6RP Qxx25NH6 1.60g Embossed Carrier 500 Qxx25J6TP Qxx25J6 5.23g Tube 250 (25 per tube) Qxx25K6TP Qxx25K6 4.40g Tube 250 (25 per tube) Qxx25xx & Qxx25xHx Series 126 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs TO-263 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards 0.63 (16.0) 0.157 (4.0) Gate 0.059 DIA (1.5) 0.945 (24.0) 0.827 (21.0) 25 A TRIACs MT1 / Cathode * * Cover tape MT2 / Anode 0.512 (13.0) Arbor Hole Dia. 12.99 (330.0) Dimensions are in inches (and millimeters). 1.01 (25.7) Direction of Feed Part Numbering System Part Marking System Q 60 25 N H6 DEVICE TYPE Q: Triac or Alternistor VOLTAGE RATING 40: 400V 60: 600V 80: 800V K0: 1000V CURRENT RATING 25: 25A TO-220AB (R & L Packages) TO-263 (N Package) SENSITIVITY Standard Triac 5: 50mA Alternistor H5: 50mA 6: 80mA H6: 80mA TO-218AC (K Package) TO-218X (J Package) Q6025K6 Q6025L5 PACKAGE TYPE L : TO-220AB Isolated R : TO-220AB Non-Isolated N : TO-263 (D2 -Pak) K : TO-218AC Isolated J : TO-218X Isolated P : Fastpak ® ® yxxxx yxxxx Fastpak (P Package) Q6025P5 yxxxx ® ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 127 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series