PIC16LF1554/1559 PIC16LF1554/1559 Memory Programming Specification This document includes the programming specifications for the following devices: 1.1.2 In Low-Voltage ICSP™ mode, these devices can be programmed using a single VDD source in the operating range. The MCLR/VPP pin does not have to be brought to a different voltage, but can instead be left at the normal operating voltage. • PIC16LF1554 • PIC16LF1559 1.0 OVERVIEW 1.1.2.1 The devices can be programmed using either the highvoltage In-Circuit Serial Programming™ (ICSP™) method or the low-voltage ICSP™ method. 1.1 Single-Supply ICSP Programming The LVP bit in Configuration Word 2 enables singlesupply (low-voltage) ICSP programming. The LVP bit defaults to a ‘1’ (enabled) from the factory. The LVP bit may only be programmed to ‘0’ by entering the HighVoltage ICSP mode, where the MCLR/VPP pin is raised to VIHH. Once the LVP bit is programmed to a ‘0’, only the High-Voltage ICSP mode is available and only the High-Voltage ICSP mode can be used to program the device. Hardware Requirements 1.1.1 LOW-VOLTAGE ICSP PROGRAMMING HIGH-VOLTAGE ICSP PROGRAMMING In High-Voltage ICSP™ mode, these devices require two programmable power supplies: one for VDD and one for the MCLR/VPP pin. Note 1: The High-Voltage ICSP mode is always available, regardless of the state of the LVP bit, by applying VIHH to the MCLR/ VPP pin. 2: While in Low-Voltage ICSP mode, MCLR is always enabled, regardless of the MCLRE bit, and the port pin can no longer be used as a general purpose input. 1.2 Pin Utilization Five pins are needed for ICSP™ programming. The pins are listed in Table 1-1. TABLE 1-1: Pin Name RA1 RA0 PIN DESCRIPTIONS DURING PROGRAMMING During Programming Function Pin Type ICSPCLK I Pin Description Clock Input – Schmitt Trigger Input ICSPDAT I/O Data Input/Output – Schmitt Trigger Input Program/Verify mode P(1) Program Mode Select/Programming Power Supply VDD VDD P Power Supply VSS VSS P Ground MCLR/VPP/RA3 Legend: Note 1: I = Input, O = Output, P = Power The programming high voltage is internally generated. To activate the Program/Verify mode, high voltage needs to be applied to MCLR input. Since the MCLR is used for a level source, MCLR does not draw any significant current. 2014 Microchip Technology Inc. Advance Information DS40001743A-page 1 PIC16LF1554/1559 2.0 DEVICE PINOUTS The pin diagrams are shown in Figure 2-1 through Figure 2-4. The pins that are required for programming are listed in Table 1-1 and shown in bold lettering in the pin diagrams. FIGURE 2-1: 14-PIN PDIP, SOIC, TSSOP DIAGRAM FOR PIC16LF1554 PDIP, SOIC, TSSOP VDD 1 14 RA5 RA4 13 VSS RA0/ICSPDAT 12 RA1/ICSPCLK 11 RA2 10 RC0 9 RC1 8 RC2 3 4 RC5 5 RC4 6 PIC16LF1554 MCLR/VPP/RA3 RC3 FIGURE 2-2: 2 7 16-PIN QFN DIAGRAM FOR PIC16LF1554 VDD NC NC Vss QFN (3x3) 16 15 14 13 1 2 3 4 12 11 10 9 PIC16LF1554 RA5 RA4 MCLR/VPP/RA3 RC5 RA0/ICSPDAT RA1/ICSPCLK RA2 RC0 RC4 RC3 RC2 RC1 5 6 7 8 FIGURE 2-3: 20-PIN PDIP, SSOP DIAGRAM FOR PIC16LF1559 PDIP, SSOP DS40001743A-page 2 1 20 VSS 2 19 RA0/ICSPDAT RA4 3 18 RA1/ICSPCLK MCLR/VPP/RA3 4 PIC16LF1559 VDD RA5 17 RA2 16 RC0 15 RC1 14 13 RC2 RC5 5 RC4 6 RC3 RC6 7 RC7 9 12 RB5 RB7 10 11 RB6 8 RB4 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 FIGURE 2-4: 20-PIN QFN DIAGRAM FOR PIC16LF1559 RA4 RA5 VDD Vss RA0/ICSPDAT QFN (4x4) MCLR/VPP/RA3 RC5 RC4 RC3 RC6 1 2 3 4 5 PIC16LF1559 20 19 18 17 16 15 14 13 12 11 RA1/ICSPCLK RA2 RC0 RC1 RC2 RC7 RB7 RB6 RB5 RB4 6 7 8 9 10 2014 Microchip Technology Inc. Advance Information DS40001743A-page 3 PIC16LF1554/1559 3.0 MEMORY MAP The memory is broken into two sections: program memory and configuration memory. Only the size of the program memory changes between devices, the configuration memory remains the same. FIGURE 3-1: PIC16LF1554 PROGRAM MEMORY MAPPING 4 KW 0000h Implemented 0FFFh Maps to 0-0FFFh 8000h User ID Location 8001h User ID Location 8002h User ID Location 8003h User ID Location 8004h Reserved 8005h Reserved 8006h Device ID 8007h Configuration Word 1 8008h Configuration Word 2 8009h Calibration Word 1 800Ah Calibration Word 2 7FFFh 8000h Program Memory Implemented 8200h Maps to 8000-81FFh Configuration Memory FFFFh 800Bh-81FFh DS40001743A-page 4 Reserved Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 FIGURE 3-2: PIC16LF1559 PROGRAM MEMORY MAPPING 8 KW 0000h Implemented 1FFFh Maps to 0-1FFFh 8000h User ID Location 8001h User ID Location 8002h User ID Location 8003h User ID Location 8004h Reserved 8005h Reserved 8006h Device ID 8007h Configuration Word 1 8008h Configuration Word 2 8009h Calibration Word 1 800Ah Calibration Word 2 7FFFh 8000h Program Memory Implemented 8200h Maps to 8000-81FFh Configuration Memory FFFFh 800Bh-81FFh 2014 Microchip Technology Inc. Reserved Advance Information DS40001743A-page 5 PIC16LF1554/1559 3.1 User ID Location A user may store identification information (user ID) in four designated locations. The user ID locations are mapped to 8000h-8003h. Each location is 14 bits in length. Code protection has no effect on these memory locations. Each location may be read with code protection enabled or disabled. MPLAB® IDE only displays the seven Least Significant bits (LSb) of each user ID location, the upper bits are not read. It is recommended that only the seven LSbs be used if MPLAB IDE is the primary tool used to read these addresses. Note: 3.2 Device ID The device ID word is located at 8006h. This location is read-only and cannot be erased or modified. DEVICE ID: DEVICE ID REGISTER(1) REGISTER 3-1: R R R R R R DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 bit 13 bit 8 R R R R R R R R DEV2 DEV1 DEV0 REV4 REV3 REV2 REV1 REV0 bit 7 bit 0 Legend: R = Readable bit P = Programmable bit ‘1’ = Bit is set ‘0’ = Bit is cleared -n = Value at POR W = Writable bit U = Unimplemented bit, read as ‘0’ x = Bit is unknown bit 13-5 DEV<8:0>: Device ID bits These bits are used to identify the part number. bit 4-0 REV<4:0>: Revision ID bits These bits are used to identify the revision. Note 1: This location cannot be written. DS40001743A-page 6 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 TABLE 3-1: DEVICE ID VALUES DEVICE DEVICE ID VALUES DEV REV PIC16LF1554 0010 1111 000 x xxxx PIC16LF1559 0010 1111 001 x xxxx 3.3 Configuration Words There are two Configuration Words, Configuration Word 1 (8007h) and Configuration Word 2 (8008h). The individual bits within these Configuration Words are used to enable or disable device functions such as the Brown-out Reset, code protection and Power-up Timer. 3.4 Calibration Words The internal calibration values are factory calibrated and stored in Calibration Words 1 and 2 (8009h, 800Ah). The Calibration Words do not participate in erase operations. The device can be erased without affecting the Calibration Words. 2014 Microchip Technology Inc. Advance Information DS40001743A-page 7 PIC16LF1554/1559 REGISTER 3-2: CONFIGURATION WORD 1 U-1 U-1 R/P-1 R/P-1 R/P-1 U-1(3) — — CLKOUTEN BOREN1 BOREN0 — bit 13 bit 8 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 U-1 R/P-1 R/P-1 CP MCLRE PWRTE WDTE1 WDTE0 — FOSC1 FOSC0 bit 7 bit 0 Legend: W = Writable bit R = Readable bit ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown -n = Value at POR U = Unimplemented bit P = Programmable Bit bit 13-12 Unimplemented: Read as ‘1’ bit 11 CLKOUTEN: Clock Out Enable bit 1 = CLKOUT function is disabled. I/O or oscillator function on CLKOUT pin. 0 = CLKOUT function is enabled on CLKOUT pin bit 10-9 BOREN<1:0>: Brown-out Reset Enable bits(1) 11 = BOR enabled 10 = BOR enabled during operation and disabled in Sleep 01 = BOR controlled by SBOREN bit of the PCON register 00 = BOR disabled bit 8(3) Unimplemented: Read as ‘1’ bit 7 CP: Code Protection bit(2) 1 = Program memory code protection is disabled 0 = Program memory code protection is enabled bit 6 MCLRE: MCLR/VPP Pin Function Select bit If LVP bit = 1: This bit is ignored. If LVP bit = 0: 1 = MCLR/VPP pin function is MCLR; Weak pull-up enabled. 0 = MCLR/VPP pin function is digital input; MCLR internally disabled; Weak pull-up under control of WPUA register. bit 5 PWRTE: Power-up Timer Enable bit(1) 1 = PWRT disabled 0 = PWRT enabled bit 4-3 WDTE<1:0>: Watchdog Timer Enable bit 11 = WDT enabled 10 = WDT enabled while running and disabled in Sleep 01 = WDT controlled by the SWDTEN bit in the WDTCON register 00 = WDT disabled bit 2 Unimplemented: Read as ‘1’ bit 1-0 FOSC<1:0>: Oscillator Selection bits 11 = ECH: External Clock, High-Power mode: on CLKIN pin 10 = ECM: External Clock, Medium-Power mode: on CLKIN pin 01 = ECL: External Clock, Low-Power mode: on CLKIN pin 00 = INTOSC oscillator: I/O function on OSC1 pin Note 1: 2: 3: Enabling Brown-out Reset does not automatically enable Power-up Timer. The entire program memory will be erased when the code protection is turned off. This bit should be maintained as ‘1’ when programmed. DS40001743A-page 8 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 REGISTER 3-3: CONFIGURATION WORD 2 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 U-1 LVP DEBUG LPBOR BORV STVREN — bit 13 bit 8 U-1 U-1 U-1 U-1 U-1 U-1 R/P-1 R/P-1 — — — — — — WRT1 WRT0 bit 7 bit 0 Legend: W = Writable bit R = Readable bit ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown -n = Value at POR U = Unimplemented bit P = Programmable Bit bit 13 LVP: Low-Voltage Programming Enable bit(1) 1 = Low-voltage programming enabled 0 = HV on MCLR/VPP must be used for programming bit 12 DEBUG: Debugger mode 1 = In-Circuit Debugger disabled, ICSPCLK and ICSPDAT pins are general purpose I/O pins 0 = In-Circuit Debugger enabled, ICSPCLK and ICSPDAT pins are dedicated to the debugger bit 11 LPBOR: Low-Power BOR bit 1 = Low-Power BOR is disabled 0 = Low-Power BOR is enabled bit 10 BORV: Brown-out Reset Voltage Selection bit 1 = Brown-out Reset Voltage (VBOR) set to 1.9V 0 = Brown-out Reset Voltage (VBOR) set to 2.7V bit 9 STVREN: Stack Overflow/Underflow Reset Enable bit 1 = Stack Overflow or Underflow will cause a Reset 0 = Stack Overflow or Underflow will not cause a Reset bit 8-2 Unimplemented: Read as ‘1’ bit 1-0 WRT<1:0>: Flash Memory Self-Write Protection bits 4 kW Flash memory (PIC16LF1554): 11 = Write protection off 10 = 000h to 1FFh write-protected, 200h to FFFh may be modified by PMCON control 01 = 000h to 7FFh write-protected, 800h to FFFh may be modified by PMCON control 00 = 000h to FFFh write-protected, no addresses may be modified by PMCON control 8 kW Flash memory (PIC16LF1559): 11 = Write protection off 10 = 0000h to 01FFh write-protected, 0200h to 1FFFh may be modified by PMCON control 01 = 0000h to 0FFFh write-protected, 1000h to 1FFFh may be modified by PMCON control 00 = 0000h to 1FFFh write-protected, no addresses may be modified by PMCON control Note 1: The LVP bit cannot be programmed to ‘0’ when Programming mode is entered via LVP. 2014 Microchip Technology Inc. Advance Information DS40001743A-page 9 PIC16LF1554/1559 4.0 PROGRAM/VERIFY MODE In Program/Verify mode, the program memory and the configuration memory can be accessed and programmed in serial fashion. ICSPDAT and ICSPCLK are used for the data and the clock, respectively. All commands and data words are transmitted LSb first. Data changes on the rising edge of the ICSPCLK and latched on the falling edge. In Program/Verify mode both the ICSPDAT and ICSPCLK are Schmitt Trigger inputs. The sequence that enters the device into Program/Verify mode places all other logic into the Reset state. Upon entering Program/Verify mode, all I/Os are automatically configured as high-impedance inputs and the address is cleared. 4.1 High-Voltage Program/Verify Mode Entry and Exit There are two different methods of entering Program/ Verify mode via high-voltage: • VPP – First entry mode • VDD – First entry mode 4.1.1 VPP – FIRST ENTRY MODE To enter Program/Verify mode via the VPP-first method the following sequence must be followed: 1. 2. 3. Hold ICSPCLK and ICSPDAT low. All other pins should be unpowered. Raise the voltage on MCLR from 0V to VIHH. Raise the voltage on VDD from 0V to the desired operating voltage. The VPP-first entry prevents the device from executing code prior to entering Program/Verify mode. For example, the device will execute code when Configuration Word 1 has MCLR disabled (MCLRE = 0), the Power-up Timer is disabled (PWRTE = 0), the internal oscillator is selected (FOSC = 100), and ICSPCLK and ICSPDAT pins are driven by the user application. Since this may prevent entry, VPP-first entry mode is strongly recommended. See the timing diagram in Figure 8-2. 4.1.2 4.1.3 PROGRAM/VERIFY MODE EXIT To exit Program/Verify mode take MCLR to VDD or lower (VIL). See Figures 8-3 and 8-4. 4.2 Low-Voltage Programming (LVP) Mode The Low-Voltage Programming mode allows devices to be programmed using VDD only, without high voltage. When the LVP bit of Configuration Word 2 register is set to ‘1’, the low-voltage ICSP programming entry is enabled. To disable the Low-Voltage ICSP mode, the LVP bit must be programmed to ‘0’. This can only be done while in the High-Voltage Entry mode. Entry into the Low-Voltage ICSP Program/Verify modes requires the following steps: 1. 2. MCLR is brought to VIL. A 32-bit key sequence is presented on ICSPDAT, while clocking ICSPCLK. The key sequence is a specific 32-bit pattern, '0100 1101 0100 0011 0100 1000 0101 0000' (more easily remembered as MCHP in ASCII). The device will enter Program/Verify mode only if the sequence is valid. The Least Significant bit of the Least Significant nibble must be shifted in first. Once the key sequence is complete, MCLR must be held at VIL for as long as Program/Verify mode is to be maintained. For low-voltage programming timing, see Figure 8-8 and Figure 8-9. Exiting Program/Verify mode is done by no longer driving MCLR to VIL. See Figure 8-8 and Figure 8-9. Note: To enter LVP mode, the LSB of the Least Significant nibble must be shifted in first. This differs from entering the key sequence on other parts. VDD – FIRST ENTRY MODE To enter Program/Verify mode via the VDD-first method the following sequence must be followed: 1. 2. 3. Hold ICSPCLK and ICSPDAT low. Raise the voltage on VDD from 0V to the desired operating voltage. Raise the voltage on MCLR from VDD or below to VIHH. The VDD-first method is useful when programming the device when VDD is already applied, for it is not necessary to disconnect VDD to enter Program/Verify mode. See the timing diagram in Figure 8-1. DS40001743A-page 10 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 4.3 Program/Verify Commands The devices implement 10 programming commands; each six bits in length. The commands are summarized in Table 4-1. Commands that have data associated with them are specified to have a minimum delay of TDLY between the command and the data. After this delay 16 clocks are required to either clock in or clock out the 14-bit data word. The first clock is for the Start bit and the last clock is for the Stop bit. TABLE 4-1: COMMAND MAPPING Mapping Command Data/Note Binary (MSb … LSb) Hex Load Configuration x 0 0 0 0 0 00h 0, data (14), 0 Load Data For Program Memory x 0 0 0 1 0 02h 0, data (14), 0 Read Data From Program Memory x 0 0 1 0 0 04h 0, data (14), 0 Increment Address x 0 0 1 1 0 06h — Reset Address x 1 0 1 1 0 16h — Begin Internally Timed Programming x 0 1 0 0 0 08h — Begin Externally Timed Programming x 1 1 0 0 0 18h — End Externally Timed Programming x 0 1 0 1 0 0Ah — Bulk Erase Program Memory x 0 1 0 0 1 09h Internally Timed Row Erase Program Memory x 1 0 0 0 1 11h Internally Timed 4.3.1 LOAD CONFIGURATION The Load Configuration command is used to access the configuration memory (user ID locations, Configuration Words, Calibration Words). The Load Configuration command sets the address to 8000h and loads the data latches with one word of data (see Figure 4-1). Note: The only way to get back to the program memory (address 0) is to exit Program/Verify mode or issue the Reset Address command after the configuration memory has been accessed by the Load Configuration command. After issuing the Load Configuration command, use the Increment Address command until the proper address to be programmed is reached. The address is then programmed by issuing either the Begin Internally Timed Programming or Begin Externally Timed Programming command. FIGURE 4-1: Externally timed writes are not supported for Configuration and Calibration bits. Any externally timed write to the Configuration or Calibration Word will have no effect on the targeted word. LOAD CONFIGURATION 1 2 3 4 5 2 1 6 15 16 TDLY ICSPCLK ICSPDAT 0 2014 Microchip Technology Inc. 0 0 0 0 X 0 Advance Information LSb MSb 0 DS40001743A-page 11 PIC16LF1554/1559 4.3.2 LOAD DATA FOR PROGRAM MEMORY The Load Data for Program Memory command is used to load one 14-bit word into the data latches. The word programs into program memory after the Begin Internally Timed Programming or Begin Externally Timed Programming command is issued (see Figure 4-2). FIGURE 4-2: LOAD DATA FOR PROGRAM MEMORY 1 2 4 3 5 2 1 6 16 15 TDLY ICSPCLK 0 ICSPDAT 4.3.3 1 0 0 0 0 X LSb MSb 0 READ DATA FROM PROGRAM MEMORY The Read Data from Program Memory command will transmit data bits out of the program memory map currently accessed, starting with the second rising edge of the clock input. The ICSPDAT pin will go into Output mode on the first falling clock edge, and it will revert to Input mode (high-impedance) after the 16th falling edge of the clock. If the program memory is code-protected (CP), the data will be read as zeros (see Figure 4-3). FIGURE 4-3: READ DATA FROM PROGRAM MEMORY 1 2 3 4 5 6 1 2 15 16 TDLY ICSPCLK ICSPDAT (from Programmer) 0 0 1 0 0 ICSPDAT (from device) X x Input DS40001743A-page 12 Advance Information LSb MSb Output Input 2014 Microchip Technology Inc. PIC16LF1554/1559 4.3.4 INCREMENT ADDRESS The address is incremented when this command is received. It is not possible to decrement the address. To reset this counter, the user must use the Reset Address command or exit Program/Verify mode and reenter it. If the address is incremented from address 7FFFh, it will wrap-around to location 0000h. If the address is incremented from FFFFh, it will wrap-around to location 8000h. FIGURE 4-4: INCREMENT ADDRESS Next Command 1 2 4 3 2 1 6 5 3 TDLY ICSPCLK 0 ICSPDAT 1 1 0 0 X X Address 4.3.5 X X Address + 1 RESET ADDRESS The Reset Address command will reset the address to 0000h, regardless of the current value. The address is used in program memory or the configuration memory. FIGURE 4-5: RESET ADDRESS Next Command 1 2 4 3 5 6 2 1 3 TDLY ICSPCLK ICSPDAT 0 Address 2014 Microchip Technology Inc. 1 1 0 1 X N Advance Information X X X 0000h DS40001743A-page 13 PIC16LF1554/1559 4.3.6 BEGIN INTERNALLY TIMED PROGRAMMING A Load Configuration or Load Data for Program Memory command must be given before every Begin Programming command. Programming of the addressed memory will begin after this command is received. An internal timing mechanism executes the write. The user must allow for the program cycle time, TPINT, for the programming to complete. The End Externally Timed Programming command is not needed when the Begin Internally Timed Programming is used to start the programming. The program memory address that is being programmed is not erased prior to being programmed. FIGURE 4-6: BEGIN INTERNALLY TIMED PROGRAMMING 1 2 5 4 3 Next Command 1 2 3 6 TPINT ICSPCLK ICSPDAT 4.3.7 0 0 0 0 1 X X X X BEGIN EXTERNALLY TIMED PROGRAMMING A Load Configuration or Load Data for Program Memory command must be given before every Begin Programming command. Programming of the addressed memory will begin after this command is received. To complete the programming the End Externally Timed Programming command must be sent in the specified time window defined by TPEXT (see Figure 4-7). Externally timed writes are not supported for Configuration and Calibration bits. Any externally timed write to the Configuration or Calibration Word will have no effect on the targeted word. FIGURE 4-7: BEGIN EXTERNALLY TIMED PROGRAMMING End Externally Timed Programming Command 1 2 4 3 5 6 1 2 3 TPEXT ICSPCLK ICSPDAT DS40001743A-page 14 0 0 0 1 1 X Advance Information 0 1 0 2014 Microchip Technology Inc. PIC16LF1554/1559 4.3.8 END EXTERNALLY TIMED PROGRAMMING This command is required after a Begin Externally Timed Programming command is given. This command must be sent within the time window specified by TPEXT after the Begin Externally Timed Programming command is sent. After sending the End Externally Timed Programming command, an additional delay (TDIS) is required before sending the next command. This delay is longer than the delay ordinarily required between other commands (see Figure 4-8). FIGURE 4-8: END EXTERNALLY TIMED PROGRAMMING 1 2 5 4 3 Next Command 2 1 3 6 TDIS ICSPCLK 4.3.9 1 0 ICSPDAT 0 1 1 BULK ERASE PROGRAM MEMORY X X X X After receiving the Bulk Erase Program Memory command the erase will not complete until the time interval, TERAB, has expired. The Bulk Erase Program Memory command performs two different functions dependent on the current state of the address. Note: Address 0000h-7FFFh: Program Memory is erased The code protection Configuration bit (CP) has no effect on the Bulk Erase Program Memory command. Configuration Words are erased Address 8000h-8008h: Program Memory is erased Configuration Words are erased User ID Locations are erased A Bulk Erase Program Memory command should not be issued when the address is greater than 8008h. FIGURE 4-9: BULK ERASE PROGRAM MEMORY 1 2 3 4 5 Next Command 2 1 3 6 TERAB ICSPCLK ICSPDAT 2014 Microchip Technology Inc. 1 0 0 1 0 X Advance Information X X X DS40001743A-page 15 PIC16LF1554/1559 4.3.10 ROW ERASE PROGRAM MEMORY The Row Erase Program Memory command will erase an individual row. Refer to Table 4-2 for row sizes of specific devices and the PC bits used to address them. If the program memory is code-protected, the Row Erase Program Memory command will be ignored. When the address is 8000h-8008h, the Row Erase Program Memory command will only erase the user ID locations, regardless of the setting of the CP Configuration bit. After receiving the Row Erase Program Memory command, the erase will not complete until the time interval, TERAR, has expired. TABLE 4-2: PROGRAMMING ROW SIZE AND LATCHES Devices PC Row Size Number of Latches PIC16LF1554 <15:5> 32 32 PIC16LF1559 <15:5> 32 32 FIGURE 4-10: ROW ERASE PROGRAM MEMORY 1 2 4 3 5 Next Command 2 1 3 6 TERAR ICSPCLK ICSPDAT DS40001743A-page 16 1 0 0 0 1 X Advance Information X X X 2014 Microchip Technology Inc. PIC16LF1554/1559 5.0 PROGRAMMING ALGORITHMS The devices use internal latches to temporarily store the 14-bit words used for programming. Refer to Table 4-2 for specific latch information. The data latches allow the user to write the program words with a single Begin Externally Timed Programming or Begin Internally Timed Programming command. The Load Program Data or the Load Configuration command is used to load a single data latch. The data latch will hold the data until the Begin Externally Timed Programming or Begin Internally Timed Programming command is given. The data latches are aligned with the LSbs of the address. The PC’s address at the time the Begin Externally Timed Programming or Begin Internally Timed Programming command is given will determine which location(s) in memory are written. Writes cannot cross the physical boundary. For example, with the PIC16LF1554, attempting to write from address 0002h0009h will result in data being written to 0008h-000Fh. If more than the maximum number of data latches are written without a Begin Externally Timed Programming or Begin Internally Timed Programming command, the data in the data latches will be overwritten. The following figures show the recommended flowcharts for programming. 2014 Microchip Technology Inc. Advance Information DS40001743A-page 17 PIC16LF1554/1559 FIGURE 5-1: DEVICE PROGRAM/VERIFY FLOWCHART Start Enter Programming Mode Bulk Erase Device Write Program Memory(1) Write User IDs Verify Program Memory Verify User IDs Write Configuration Words(2) Verify Configuration Words Exit Programming Mode Done Note 1: See Figure 5-2. 2: See Figure 5-5. DS40001743A-page 18 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 FIGURE 5-2: PROGRAM MEMORY FLOWCHART Start Bulk Erase Program Memory(1, 2) Program Cycle(3) Read Data from Program Memory Data Correct? No Report Programming Failure Yes Increment Address Command No All Locations Done? Yes Done Note 1: This step is optional if the device has already been erased or has not been previously programmed. 2: If the device is code-protected or must be completely erased, then Bulk Erase the device per Figure 5-6. 3: See Figure 5-3 or Figure 5-4. 2014 Microchip Technology Inc. Advance Information DS40001743A-page 19 PIC16LF1554/1559 FIGURE 5-3: ONE-WORD PROGRAM CYCLE Program Cycle Load Data for Program Memory Begin Programming Command (Internally timed) Begin Programming Command (Externally timed)(1) Wait TPINT Wait TPEXT End Programming Command Wait TDIS Note 1: Externally timed writes are not supported for Configuration and Calibration bits. DS40001743A-page 20 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 FIGURE 5-4: MULTIPLE-WORD PROGRAM CYCLE Program Cycle Load Data for Program Memory Latch 1 Increment Address Command Load Data for Program Memory Latch 2 Increment Address Command Load Data for Program Memory Latch n Begin Programming Command (Internally timed) Begin Programming Command (Externally timed) Wait TPINT Wait TPEXT End Programming Command Wait TDIS 2014 Microchip Technology Inc. Advance Information DS40001743A-page 21 PIC16LF1554/1559 FIGURE 5-5: CONFIGURATION MEMORY PROGRAM FLOWCHART Start Load Configuration Bulk Erase Program Memory(1) One-word Program Cycle(2) (User ID) Read Data From Program Memory Command Data Correct? No Report Programming Failure Yes Increment Address Command No Address = 8004h? Yes Increment Address Command Increment Address Command Increment Address Command One-word Program Cycle(2) (Config. Word 1) Read Data From Program Memory Command Data Correct? No Report Programming Failure Yes Increment Address Command One-word Program Cycle(2) (Config. Word 2) Read Data From Program Memory Command Data Correct? No Report Programming Failure Yes Note 1: This step is optional if the device is erased or not previously programmed. 2: See Figure 5-3. DS40001743A-page 22 Advance Information Done 2014 Microchip Technology Inc. PIC16LF1554/1559 FIGURE 5-6: ERASE FLOWCHART Start Load Configuration Bulk Erase Program Memory Done Note: This sequence does not erase the Calibration Words. 2014 Microchip Technology Inc. Advance Information DS40001743A-page 23 PIC16LF1554/1559 6.0 CODE PROTECTION 7.0 Code protection is controlled using the CP bit in Configuration Word 1. When code protection is enabled, all program memory locations (0000h-7FFFh) read as ‘0’. Further programming is disabled for the program memory (0000h-7FFFh). The user ID locations and Configuration Words can be programmed and read out regardless of the code protection settings. 6.1 Program Memory Code protection is enabled by programming the CP bit in Configuration Word 1 register to ‘0’. The only way to disable code protection is to use the Bulk Erase Program Memory command. HEX FILE USAGE In the hex file there are two bytes per program word stored in the Intel® INHX32 hex format. Data is stored LSB first, MSB second. Because there are two bytes per word, the addresses in the hex file are 2x the address in program memory. (Example: Configuration Word 1 is stored at 8007h on the PIC16LF1554. In the hex file this will be referenced as 1000Eh-1000Fh). 7.1 Configuration Word To allow portability of code, it is strongly recommended that the programmer is able to read the Configuration Words and user ID locations from the hex file. If the Configuration Words information was not present in the hex file, a simple warning message may be issued. Similarly, while saving a hex file, Configuration Words and user ID information should be included. 7.2 Device ID and Revision If a device ID is present in the hex file at 1000Ch1000Dh (8006h on the part), the programmer should verify the device ID (excluding the revision) against the value read from the part. On a mismatch condition the programmer should generate a warning message. DS40001743A-page 24 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 7.3 Checksum Computation 7.3.1 The checksum is calculated by two different methods dependent on the setting of the CP Configuration bit. TABLE 7-1: CONFIGURATION WORD MASK VALUES Config. Word 1 Mask Config. Word 2 Mask PIC16LF1554 0EFBh 3E03h PIC16LF1559 0EFBh 3E03h Device EXAMPLE 7-1: PIC16LF1554 PROGRAM CODE PROTECTION DISABLED With the program code protection disabled, the checksum is computed by reading the contents of the program memory locations and adding up the program memory data starting at address 0000h, up to the maximum user addressable location. Any Carry bit exceeding 16 bits are ignored. Additionally, the relevant bits of the Configuration Words are added to the checksum. All unimplemented Configuration bits are masked to ‘0’. CHECKSUM COMPUTED WITH PROGRAM CODE PROTECTION DISABLED (CP = 1), PIC16LF1554, BLANK DEVICE Sum of Memory addresses 0000h-0FFFh F000h(1) Configuration Word 1 3FFFh(2) Configuration Word 1 mask 0EFBh(3) Configuration Word 2 3FFFh(4) Configuration Word 2 mask 3E03h(5) Checksum = F000h + (3FFFh and 0EFBh) + (3FFFh and 3E03h)(6) = F000h + 0EFBh + 3E03h = 3CFEh Note 1: 2: 3: 4: 5: 6: This value is obtained by taking the total number of program memory locations (0x000 to 0xFFFh which is 1000h) and multiplying it by the blank memory value of 0x3FFF to get the sum of 3FF F000h. Then, truncate to 16 bits, thus having a final value of F000h. This value is obtained by making all bits of the Configuration Word 1 a ‘1’, then converting it to hex, thus having a value of 3FFFh. This value is obtained by making all used bits of the Configuration Word 1 a ‘1’, then converting it to hex, thus having a value of 0EFBh. This value is obtained by making all bits of the Configuration Word 2 a ‘1’, then converting it to hex, thus having a value of 3FFFh. This value is obtained by making all used bits of the Configuration Word 2 a ‘1’, then converting it to hex, thus having a value of 3E03h. This value is obtained by ANDing the Configuration Word value with the Configuration Word Mask Value and adding it to the sum of memory addresses: (3FFFh and 0EFBh) + (3FFFh and 3E03h) + F000h = 1 3CFEh. Then, truncate to 16 bits, thus having a final value of 3CFEh. 2014 Microchip Technology Inc. Advance Information DS40001743A-page 25 PIC16LF1554/1559 EXAMPLE 7-2: PIC16LF1554 CHECKSUM COMPUTED WITH PROGRAM CODE PROTECTION DISABLED (CP = 1), PIC16LF1554, 00AAh AT FIRST AND LAST ADDRESS Sum of Memory addresses 0000h-0FFFh 7156h(1) Configuration Word 1 3FFFh(2) Configuration Word 1 mask 0EFBh(3) Configuration Word 2 3FFFh(4) Configuration Word 2 mask 3E03h(5) Checksum = 7156h + (3FFFh and 0EFBh) + (3FFFh and 3E03h)(6) = 7156h + 0EFBh + 3E03h = BE54h Note 1: 2: 3: 4: 5: 6: This value is obtained by taking the total number of program memory locations (0x000 to 0xFFFh which is 1000h) subtracting 2h which yields FFEh, then multiplying it by the blank memory value of 0x3FFF to get the sum of 3FF 7002h. Then, truncate to 16 bits the value of 7002h. Now add 0154h (00AAh + 00AAh) to 7002h to get the final value of 7156h. This value is obtained by making all bits of the Configuration Word 1 a ‘1’, then converting it to hex, thus having a value of 3FFFh. This value is obtained by making all used bits of the Configuration Word 1 a ‘1’, then converting it to hex, thus having a value of 0EFBh. This value is obtained by making all bits of the Configuration Word 2 a ‘1’, then converting it to hex, thus having a value of 3FFFh. This value is obtained by making all used bits of the Configuration Word 2 a ‘1’, then converting it to hex, thus having a value of 3E03h. This value is obtained by ANDing the Configuration Word value with the Configuration Word Mask Value and adding it to the sum of memory addresses: (3FFFh and 0EFBh) + (3FFFh and 3E03h) + 7156h = BE54h. Then, truncate to 16 bits, thus having a final value of BE54h. DS40001743A-page 26 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 7.3.2 PROGRAM CODE PROTECTION ENABLED With the program code protection enabled, the checksum is computed in the following manner: The Least Significant nibble of each user ID is used to create a 16-bit value. The masked value of user ID location 8000h is the Most Significant nibble. This sum of user IDs is summed with the Configuration Words (all unimplemented Configuration bits are masked to ‘0’). EXAMPLE 7-3: PIC16LF1554 CHECKSUM COMPUTED WITH PROGRAM CODE PROTECTION ENABLED (CP = 0), PIC16LF1554, BLANK DEVICE Configuration Word 1 3F7Fh(1) Configuration Word 1 mask 0E7Bh(2) Configuration Word 2 3FFFh(3) Configuration Word 2 mask 3E03h(4) User ID (8000h) 0006h(5) User ID (8001h) 0007h(5) User ID (8002h) 0001h(5) User ID (8003h) 0002h(5) Sum of User IDs = (0006h and 000Fh) << 12 + (0007h and 000Fh) << 8 + (0001h and 000Fh) << 4 + (0002h and 000Fh)(6) = 6000h + 0700h + 0010h + 0002h = 6712h Checksum = (3F7Fh and 0E7Bh) + (3FFFh and 3E03h) + Sum of User IDs(7) = 0E7Bh + 3E03h + 6712h = B390h Note 1: 2: 3: 4: 5: 6: 7: This value is obtained by making all bits of the Configuration Word 1 a ‘1’, but the code-protect bit is ‘0’ (thus, enabled), then converting it to hex, thus having a value of 3F7Fh. This value is obtained by making all used bits of the Configuration Word 1 a ‘1’, but the code-protect bit is ‘0’ (thus, enabled), then converting it to hex, thus having a value of 0E7Bh. This value is obtained by making all bits of the Configuration Word 2 a ‘1’, then converting it to hex, thus having a value of 3FFFh. This value is obtained by making all used bits of the Configuration Word 2 a ‘1’, then converting it to hex, thus having a value of 3E03h. These values are picked at random for this example; they could be any 16-bit value. In order to calculate the sum of user IDs, take the 16-bit value of the first user ID location (0006h), AND the address to (000Fh), thus masking the MSB. This gives you the value 0006h, then shift left 12 bits, giving you 6000h. Do the same procedure for the 16-bit value of the second user ID location (0007h), except shift left eight bits. Also, do the same for the third user ID location (0001h), except shift left four bits. For the fourth user ID location do not shift. Finally, add up all four user ID values to get the final sum of user IDs of 6712h. This value is obtained by ANDing the Configuration Word value with the Configuration Word Mask Value and adding it to the sum of user IDs: (3F7Fh AND 0E7Bh) + (3FFFh AND 3E03h) + 6712h = B390h. 2014 Microchip Technology Inc. Advance Information DS40001743A-page 27 PIC16LF1554/1559 EXAMPLE 7-4: CHECKSUM COMPUTED WITH PROGRAM CODE PROTECTION ENABLED (CP = 0), PIC16LF1554, 00AAh AT FIRST AND LAST ADDRESS PIC16LF1554 Configuration Word 1 3F7Fh(1) Configuration Word 1 mask 0E7Bh(2) Configuration Word 2 3FFFh(3) Configuration Word 2 mask 3E03h(4) User ID (8000h) 000Eh(5) User ID (8001h) 0008h(5) User ID (8002h) 0005h(5) User ID (8003h) 0008h(5) Sum of User IDs = (000Eh and 000Fh) << 12 + (0008h and 000Fh) << 8 + (0005h and 000Fh) << 4 + (0008h and 000Fh)(6) = E000h + 0800h + 0050h + 0008h = E858h Checksum = (3F7Fh and 0E7Bh) + (3FFFh and 3E03h) + Sum of User IDs(7) = 0E7Bh + 3E03h + E858h = 34D6h Note 1: 2: 3: 4: 5: 6: 7: This value is obtained by making all bits of the Configuration Word 1 a ‘1’, but the code-protect bit is ‘0’ (thus, enabled), then converting it to hex, thus having a value of 3F7Fh. This value is obtained by making all used bits of the Configuration Word 1 a ‘1’, but the code-protect bit is ‘0’ (thus, enabled), then converting it to hex, thus having a value of 0E7Bh. This value is obtained by making all bits of the Configuration Word 2 a ‘1’, then converting it to hex, thus having a value of 3FFFh. This value is obtained by making all used bits of the Configuration Word 2 a ‘1’, then converting it to hex, thus having a value of 3E03h. These values are picked at random for this example; they could be any 16-bit value. In order to calculate the sum of user IDs, take the 16-bit value of the first user ID location (000Eh), AND the address to (000Fh), thus masking the MSB. This gives you the value 000Eh, then shift left 12 bits, giving you E000h. Do the same procedure for the 16-bit value of the second user ID location (0008h), except shift left eight bits. Also, do the same for the third user ID location (0005h), except shift left four bits. For the fourth user ID location do not shift. Finally, add up all four user ID values to get the final sum of user IDs of E858h. This value is obtained by ANDing the Configuration Word value with the Configuration Word Mask Value and adding it to the sum of user IDs: (3F7Fh AND 0E7Bh) + (3FFFh AND 3E03h) + E858h = 34D6h. DS40001743A-page 28 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 8.0 ELECTRICAL SPECIFICATIONS Refer to the device specific data sheet for absolute maximum ratings. TABLE 8-1: AC/DC CHARACTERISTICS TIMING REQUIREMENTS FOR PROGRAM/VERIFY MODE Standard Operating Conditions Production tested at 25°C AC/DC CHARACTERISTICS Sym. Characteristics Min. Typ. Max. Units Conditions/Comments Supply Voltages and Currents VDD VDD Read/Write and Row Erase operations Bulk Erase operations IDDI Current on VDD, Idle IDDP Current on VDD, Programming VDD min. — VDD max. V 2.7 — VDD max. V — — 1.0 mA — — 3.0 mA VPP IPP Current on MCLR/VPP — — 600 A VIHH High voltage on MCLR/VPP for Program/Verify mode entry 8.0 — 9.0 V TVHHR MCLR rise time (VIL to VIHH) for Program/Verify mode entry — — 1.0 s I/O pins VIH (ICSPCLK, ICSPDAT, MCLR/VPP) input high level 0.8 VDD — — V VIL (ICSPCLK, ICSPDAT, MCLR/VPP) input low level ICSPDAT output high level — VDD-0.7 VDD-0.7 — 0.2 VDD V — — V — — VSS+0.6 VSS+0.6 V — ns — s — — — — ns ns ns ns 80 ns 80 ns 80 ns — s 5 2.5 ms ms 2.5 5 2.1 ms ms ms VOH VOL TENTS TENTH TCKL TCKH TDS TDH TCO TLZD THZD TDLY TERAB TERAR TPINT ICSPDAT output low level Programming Mode Entry and Exit Programing mode entry setup time: ICSPCLK, 100 — ICSPDAT setup time before VDD or MCLR Programing mode entry hold time: ICSPCLK, 250 — ICSPDAT hold time after VDD or MCLR Serial Program/Verify Clock Low Pulse Width 100 — Clock High Pulse Width 100 — Data in setup time before clock 100 — Data in hold time after clock 100 — Clock to data out valid (during a 0 — Read Data command) Clock to data low-impedance (during a 0 — Read Data command) Clock to data high-impedance (during a 0 — Read Data command) Data input not driven to next clock input (delay required between command/data or command/ 1.0 — command) Bulk Erase cycle time — — Row Erase cycle time — — Internally timed programming operation time TPEXT — — 1.0 — — — Externally timed programming pulse Time delay from program to compare 300 — — TDIS (HV discharge time) TEXIT Time delay when exiting Program/Verify mode 1 — — Note 1: Externally timed writes are not supported for Configuration and Calibration bits. 2014 Microchip Technology Inc. Advance Information IOH = 3 mA, VDD = 3.3V IOH = 2 mA, VDD = 1.8V IOH = 6 mA, VDD = 3.3V IOH = 3 mA, VDD = 1.8V Program memory Configuration Words Note 1 s s DS40001743A-page 29 PIC16LF1554/1559 8.1 AC Timing Diagrams FIGURE 8-1: FIGURE 8-4: PROGRAMMING MODE ENTRY – VDD FIRST TENTS PROGRAMMING MODE EXIT – VDD LAST TEXIT VIHH TENTH VPP VIL VIHH VPP VDD VIL ICSPDAT VDD ICSPCLK ICSPDAT ICSPCLK FIGURE 8-2: PROGRAMMING MODE ENTRY – VPP FIRST TENTS TENTH VIHH VPP VIL VDD ICSPDAT ICSPCLK FIGURE 8-3: PROGRAMMING MODE EXIT – VPP LAST TEXIT VIHH VPP VIL VDD ICSPDAT ICSPCLK DS40001743A-page 30 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 FIGURE 8-5: CLOCK AND DATA TIMING TCKL TCKH ICSPCLK TDS TDH ICSPDAT as input TCO ICSPDAT as output TLZD ICSPDAT from input to output THZD ICSPDAT from output to input FIGURE 8-6: WRITE COMMAND-PAYLOAD TIMING TDLY 1 2 3 4 5 X X X X X 1 6 2 15 16 ICSPCLK ICSPDAT 0 LSb X 0 Next Command Payload Command FIGURE 8-7: MSb READ COMMAND-PAYLOAD TIMING TDLY 1 2 3 4 5 X ICSPDAT (from Programmer) X X X X 6 2 1 15 16 ICSPCLK X x ICSPDAT (from Device) Command 2014 Microchip Technology Inc. Advance Information LSb MSb Payload 0 Next Command DS40001743A-page 31 PIC16LF1554/1559 FIGURE 8-8: LVP ENTRY (POWERED) VDD MCLR TENTS TENTH 33 clocks TCKH TCKL ICSPCLK TDH TDS LSb of Pattern 0 ICSPDAT FIGURE 8-9: MSb of Pattern 1 2 ... 31 LVP ENTRY (POWERING UP) VDD MCLR TENTH 33 Clocks TCKH TCKL ICSPCLK TDH TDS LSb of Pattern 0 ICSPDAT Note 1: 1 2 ... MSb of Pattern 31 Sequence matching can start with no edge on MCLR first. DS40001743A-page 32 Advance Information 2014 Microchip Technology Inc. PIC16LF1554/1559 APPENDIX A: REVISION HISTORY Revision A (03/2014) Initial release of this document. 2014 Microchip Technology Inc. Advance Information DS40001743A-page 33 PIC16LF1554/1559 NOTES: DS40001743A-page 34 Advance Information 2014 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2014, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620779569 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2014 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. Advance Information DS40001743A-page 35 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Canada - Toronto Tel: 905-673-0699 Fax: 905-673-6509 DS40001743A-page 36 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Dusseldorf Tel: 49-2129-3766400 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Pforzheim Tel: 49-7231-424750 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Venice Tel: 39-049-7625286 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Poland - Warsaw Tel: 48-22-3325737 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 Advance Information 10/28/13 2014 Microchip Technology Inc.