63 www.vishay.com Vishay Spectrol 3/8" Square (10 mm) Single-Turn Cermet Trimmer FEATURES • Arrow and graduations for repeatable settings • “O” ring seal for solvent and aqueous washing • Rigid board mounting achieved with pins secured in housing • Multi-finger wiper for better contact resistance • Solid end stop • Tests according to CECC 41000 or IEC 60393-1 The Model 63 cermet trimmer is available in several pin configurations for top or side adjustment and with a choice of Knob styles for finger setting. Quick adjustment is achieved with multi-finger wiper and the standard resistance range is between 100 and 2 M with a tolerance of ± 10 %. • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 DIMENSIONS in inches (millimeters) ± 0.02" (0.5 mm) 0.01 (0.25) T607 (all pin styles) 0.190 (4.83) 0.188 (4.78) min. 0.395 (10.03) 0.2 ± 0.010 (5.1 ± 0.25) Ø 0.330 (8.38) 0.020 x 0.012 (0.51 x 0.30) 0.410 (10.41) 63P 63X 0.100 (2.54) 0.375 (9.52) 0.01 (0.25) T640 (pin styles P and M) 0.100 (2.54) 0.177 (4.5) 0.100 (2.54) 0.375 (9.52) 0.045 (1.14) Ø 0.550 (13.97) 0.320 (8.13) 63M T614 (all pin styles) 63S 0.100 (2.54) 0.100 (2.54) 0.100 (2.54) Revision: 22-Sep-15 0.40 (1.02) 0.119 (3.02) Document Number: 57027 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 63 www.vishay.com Vishay Spectrol ELECTRICAL SPECIFICATIONS Effective travel 270° nominal 100 to 2 M Resistance range Resistance tolerance ± 10 % 2 or 1 % whichever is greater End resistance Temperature coefficient of resistance (typical) ± 100 ppm/°C 0.5 W at +70 °C derated linearly to 0 W at 125 °C maximum voltage not to exceed 250 V Power rating c a Circuit diagram (1) (3) b (2) Dielectric withstand voltage cw 1000 VAC at sea level; 250 VAC at 80 000 ft (24 000 m) Insulation resistance (500 VDC) 1000 M minimum 1 % or 1 , whichever is greater Contact resistance variation MECHANICAL SPECIFICATIONS Mechanical travel 300° ± 50 Starting torque 35 mNm max. Weight 0.03 oz. (0.85 g) max. Resistance element Cermet 2 terminal adjustability ± 0.15 % of RT 3 terminal adjustability ± 0.05 % of applied voltage Terminals Pure Sn (code e3) ENVIRONMENTAL SPECIFICATIONS Temperature range -55 °C to +125 °C Climatic category 55/125/21 Sealing IP64 PERFORMANCES TESTS Vibration Electrical endurance Soldering Resistance to heat Damp heat steady state Mechanical life CHANGE PER CECC CONDITIONS MAX. (R) VAB/VAC 98 m/s2, 10 Hz to 500 Hz 1% 2% 1000 h 3% - - - - PER IEC PER MIL (PARA 2.3.2) Test FC (IEC 6-2-6) Method 204 (PARA 2.5.16) - No equiv. (PARA 2.3.7) Test TB (IEC 68-2-20) Method 208 41100 - 1% - (PARA 2.3.7) Test B (IEC 68-2-20A) Method 210 21 days 3% - (PARA 2.1) Test C (IEC 68-2-3) Method 103 200 cycles 3% - - Method 2 - - - - Terminal strength 2.2 lbs. (1 kg) min. Note • Nothing stated herein shall be construed as a guarantee of quality or durability. MARKING • • • • • • Vishay trademark Model Resistance value Tolerance Date code Terminal identification Revision: 22-Sep-15 Document Number: 57027 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 63 www.vishay.com Vishay Spectrol PACKAGING • In box of 200 pieces code B40 (BO200) • On request : In box of 100 pieces code B30 (BO100) In tube of 50 pieces code T20 (TU50) ORDERING INFORMATION (Part Number) M 6 3 P 2 0 1 K B 4 0 T 6 Model STYLE OHMIC VALUE TOLERANCE PACKAGING CODE M63 P M X S From 100 to 2 M 201 = 200R K = 10 % B40 = box 200 pieces On request: B30 = box 100 pieces T20 = tube 50 pieces 7 0 SPECIAL NUMBER (If applicable) Given by Vishay for custom design DESCRIPTION (for information only) 63 P 200U 10 % T607 BO200 e3 MODEL STYLE VALUE TOLERANCE SPECIAL PACKAGING LEAD FINISH RELATED DOCUMENTS APPLICATION NOTES Potentiometers and Trimmers www.vishay.com/doc?51001 Guidelines for Vishay Sfernice Resistive and Inductive Components www.vishay.com/doc?52029 Revision: 22-Sep-15 Document Number: 57027 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000