8 7 6 5 4 3 TITANIUM COMPATIBLE LASER WELDABLE 50 OHM FEEDTHROUGH SMP ADAPTABLE, .015 DIAMETER CENTER CONTACT 2 SRIFT1028 DOCUMENT: REVISIONS REV DCN REVISION DATE - INIT RLSE 7/17/2015 RELEASE APPROVAL Jim Petri 2015.07.17 14:44:06 -04'00' • DESIGNED TO LASER WELD INTO AN ELECTRONIC CHASSIS WALL D • INDUSTRY STANDARD NICKEL-IRON-COBALT ALLOY CONTACT WITH CORNING 7070 EQUIVALENT GLASS D • INTEGRAL RF GROUNDING TAB FOR EXCELLENT PERFORMANCE OVER TEMPERATURE 1. LEAK RATE: LESS THAN OR EQUAL TO 1X10E-9 CC/SEC He AT ONE ATMOSPHERE DIFFERENTIAL PRESSURE. 2. NOMINAL IMPEDANCE: 50 OHMS 3. INTERFACE IN ACCORDANCE WITH MIL-STD-348, SMP. 4. MATERIALS: PIN: NICKEL-IRON-COBALT ALLOY IN ACCORDANCE WITH ASTM F15 DIELECTRIC: CORNING 7070 EQUIVALENT GLASS (MATCHED SEAL) FERRULE: NICKEL-IRON-COBALT ALLOY IN ACCORDANCE WITH ASTM F15 SHELL (WELD FLANGE): TITANIUM GRADE 2 (UNALLOYED) IN ACCORDANCE WITH ASTM B265 OR B348 RF GROUNDING SPRING: BERYLLIUM-COPPER ALLOY 172/173 IN ACCORDANCE WITH ASTM B 194 (NICKEL AND GOLD PLATED) 5. FINISH, CONTACT AND SHELL (EXCEPT WELD FLANGE): NICKEL PLATE PER QQ-N-290, .000100/.000250 THICK. GOLD PLATE PER ASTM B488-11, TYPE III, CODE A, .000050/.000150 THICK. C 6. ORDERING INSTRUCTIONS: SPECIFY BASE NUMBER FOLLOWED BY DASH NUMBERS INDICATING DETENT TYPE, PIN LENGTH, AND DIELECTRIC APPLICATION. C EXAMPLE: SRIFT1028 - FD 130 A R ADD R FOR FULL RADIUS PIN END CONFIGURATION A=GROUNDING SPRING FOR AIR DIELECTRIC T=GROUNDING SPRING FOR TEFLON DIELECTRIC PIN LENGTH, L=.130 DETENT (FD=FULL, LD=LIMITED, SB=SMOOTH) BASE NUMBER B B A A TITLE THE INFORMATION CONTAINED IN THIS DOCUMENT IS THE SOLE PROPERTY OF SRI HERMETICS. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF SRI HERMETICS IS STRICTLY PROHIBITED. PRINTED COPIES NOT CONTROLLED FORM 300060 REV A 7 6 5 4 3 a division of WINCHESTER CONNECTOR, SMP, TC LBW (HALF SHROUD/FULL BODY) SIZE DOCUMENT A SCALE 8:1 2 SRIFT1028 CAD GENERATED DRAWING DO NOT MANUALLY UPDATE ALL SHEETS SAME REVISION SHEET 1 REV - 1 OF 2 8 6 7 4 5 3 2 SRIFT1028 DOCUMENT: .162 D .070 .175 L±.001 D .145 .115 PIN END STYLE PIN DIELECTRIC .015±.001 GROUND SPRING C C FERRULE WELD FLANGE RECOMMENDED HOLE DETAIL AS REQUIRED .043±.001 .049 .001 .005 .035 .001 THRU (AIR SIELECTRIC SHOWN (TEFLON DIELECTRIC, OPTIONAL) .1200 .0005 SHOWN .178 .001 SHOWN .238 MIN .005 .002 INSTALL THIS DIRECTION .042±.001 .035 (AIR DIELECTRIC APPLICATION) .050 (TEFLON DIELECTRIC APPLICATION) .115±.002 B B 8X 45° NO PLATING .0020±.0005 8X .012 RF GROUNDING SPRING, SHIPPED UNINSTALLED PART NUMBER SRIFT1020-GS1, AIR DIELECTRIC PART NUMBER SRIFT1020-GS2, TEFLON DIELECTRIC A TITLE THE INFORMATION CONTAINED IN THIS DOCUMENT IS THE SOLE PROPERTY OF SRI HERMETICS. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF SRI HERMETICS IS STRICTLY PROHIBITED. PRINTED COPIES NOT CONTROLLED FORM 300060 REV A 7 6 5 4 3 a division of WINCHESTER CONNECTOR, SMP, TC LBW (HALF SHROUD/FULL BODY) SIZE DOCUMENT A SCALE A 10:1 2 SRIFT1028 CAD GENERATED DRAWING DO NOT MANUALLY UPDATE ALL SHEETS SAME REVISION SHEET 1 REV - 2 OF 2