30C90 definite purpose contactor • 30C 90FLA Definite Purpose Contactor • Robust 2 & 3 Pole Contactor • Arc Covers as standard • Industry Standard Mounting • RoHS Compliant • UL File No: E61703 Contact Data Arrangements: Table 1 2 Form X (2PST-NO-DM) 3 Form X (3PST-NO-DM) Material: AgCdO, AgSnOInO Model No 30C90-1022 30C90-1023 Full Load Amps (FLA) Poles 90 Line Voltage (VAC) Locked Rotor Amps (LRA) 120 540 240/277 540 480 450 600 360 120 540 240/277 540 480 450 600 360 2 90 3 Max. HP Resistive Amps 120 120 Voltage 1 Phase 3 Phase 120 7.5 - 240 20 30 480 - 50 600 - 50 120 7.5 - 240 20 30 480 - 50 600 - 50 FLA rating tested for 6000 cycles of endurance at 240/480/600VAC per UL508. Resistive Heat rating tested for 250,000 cycles at 277VAC. LRA rating tested for 6000 cycles of Locked Rotor endurance per UL508. Coil Data Table 2 Voltage: 24-277VAC 50/60Hz. See coil data below. (480VAC available but not UL approved) Insulation Class: UL Class B (130°C) Coil Voltage Code Minimum Inrush Nominal Coil Power Coil Resistance (Ohms) Must Release Must Operate Max Voltage VA @ 50Hz VA @ 60Hz VA @ 50Hz VA @ 60Hz 24 0.63 6 18 26.4 285 240 42 27 5120 120 15.6 20 88 132 285 240 42 27 5230 208/240 63.5 40 177 264 285 240 42 27 5277 277 84 65 220 305 285 240 42 27 5480 480 255 150 384 528 285 240 42 27 5024 Page 1 of 3 Coil Operating Voltage (VAC) Rated Voltage 50/60Hz Ref: 30C90 101711JHM www.aecsensors.com Sales Department Tel: (888) 847-6552 30C90 definite purpose contactor General Specifications Table 2 Initial Operate Time mS 40 Terminations Release Time mS 25 (typical) Bounce Time mS ≤ 15 Coil Terminals Arc Cover Standard Insulation System UL Class B 130°C Power Terminals Initial Dielectric Strength between contacts and coil box lug 14-1/0 AWG box lug 50 in.lbf (5.65 Nm) box lug 14-1/0 AWG VAC 2200 between poles VAC 2200 (includes shunt) between open contacts Recommended Tightening Torque VAC 2200 Temperature Range °C Unit Weight (approx.) 0.250” QC + #6-32 screw (dual 0.250” QC optional) per terminal 3 pole -40 ... +65 Wire size 4lb Ordering Codes Type 3 0 C Contact material 9 0 - 1 0 Contact arrangement 2 Cover protection and terminations - 1 Coil code - - Contact Ratings 90 - 90FLA see Table 1 Contact Material 10 - AgCdO (standard) 70 - AgSnOInO T Terminals Contact number & arrangement 22 - DPST-NO 23 - 3PST-NO L Terminals Cover protection category 1 - IP00, no overall cover Termination Codes (see drawings for full specifications) 1 - #10-32 combination philips screw with quad QC blades 2 - Same as 1 with sems screw and pressure plate 3 - #14-4AWG box lug with quad QC blades (box lug with quick connect) 4 - #14-4AWG box lug with dual QC blades (box lug with quick connect) (std for 40FLA) 5 - #10-32 combination phillips screw with dual QC blades (20-30FLA) 6 - #14-2AWG box lug with QC blades (standard for 50-60FLA) 7 - #14-1AWG box lug with QC blades (standard for 75-150FLA) Reserved for Customer Specific Requirements 001 - Dual 0.25” QC blades for coil terminations 002 - 999 - optional customer specific number Page 2 of 3 Ref: 30C90 101711JHM www.aecsensors.com Sales Department Tel: (888) 847-6552 Special options 30C90 definite purpose contactor Fig. 1 Overall Dimensions 3.75 .20 4.05 4.62 5.00 2.50 2.90 3.75 Dimensions in inches 2 Pole same as 3 pole minus centre terminals Power Terminations Termination Codes: 1 & 5 Standard for 20-30FLA only #10-32 combination phillips/slotted and 5/16 hex head screw with #12 washer Termination Code: 6 Standard for 50 & 60FLA Box Lug 14-2 AWG (Cu/Al) Termination Code: 2 Optional for 20-40FLA only. #10-32 sems screw with pressure plate Termination Code: 7 Standard for 75 & 90FLA Box Lug 14-1 AWG (Cu/Al) Termination Codes: 3 & 4 Standard for 40FLA only Box Lug 14-4 AWG (Cu/Al) 0.25 6 Dimension in inches American Electronic Components Inc,. 1100 Lafayette St., Elkhart, IN 46516 Toll Free: (888) 847-6552, Tel: (574) - 295-6330 www.aecsensors.com Specifications and availability are liable to change without notice. Page 3 of 3 Ref: 30C90 101711JHM www.aecsensors.com Sales Department Tel: (888) 847-6552 0.28 6 0.39 5