1N5615 THRU 1N5623 GLASS PASSIVATED FAST SWITCHING RECTIFIER Reverse Voltage - 200 to 1000 Volts Forward Current - 1.0 Ampere FEATURES ♦ High temperature metallurgically bonded construction ♦ Hermetically sealed case ♦ Glass passivated cavity-free junction ♦ 1.0 Ampere operation at TA=55°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ Fast switching for high efficiency ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension P A T E N T E D * DO-204AP 0.034 (0.86) 0.028 (0.71) DIA. 1.0 (25.4) MIN. 0.240 (6.1) MAX. 0.150 (3.8) 0.100 (2.5) DIA. MECHANICAL DATA 1.0 (25.4) MIN. Case: JEDEC DO-204AP Solid glass body Terminals: Solder plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.02 ounce, 0.56 gram Dimensions in inches and (millimeters) *Brazed-lead assembly is covered by Patent No. 3,930,306 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N5615 1N5617 1N5619 1N5621 1N5623 UNITS *Maximum repetitive peak reverse voltage VRRM 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 140 280 420 560 700 Volts *Maximum DC blocking voltage VDC 200 400 600 800 1000 Volts *Minimum reverse breakdown voltage at 50 µA V(BR) 220 440 660 880 1100 Volts *Maximum average forward rectified current 0.375” (9.5mm) lead length at T A=55°C I(AV) 1.0 Amp *Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 50.0 Amps VF 1.2 Volts IR 0.5 25.0 1500.0 µA *Maximum instantaneous forward voltage at 1.0A *Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=100°C TA=200°C *Maximum reverse recovery time (NOTE 1) trr 150 150 250 300 500 ns *Maximum junction capacitance (NOTE 2) CJ 45 35 25 20 15 pF Typical thermal resistance (NOTE 3) *Operating junction temperature range *Storage temperature range RΘJA 55.0 °C/W TJ -65 to +175 °C TSTG -65 to +200 °C NOTES: (1) Reverse recovery test conditions IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 12 Volts (3) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length, P.C.B.mounted *JEDEC registered values 4/98 RATINGS AND CHARACTERISTIC CURVES 1N5615 THRU 1N5623 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.0 50 RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTH 0.75 0.5 0.25 0 25 50 75 100 125 150 175 INSTANTANEOUS SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE AMBIENT TEMPERATURE, °C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) TJ=TJ max. 40 30 20 10 0 1 10 100 NUMBER OF CYCLES AT 60 HZ FIG. 3 -TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10.0 INSTANTANEOUS FORWARD CURRENT, AMPERES 20 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 1 TJ=125°C 1 TJ=75°C 0.1 TJ=25°C FIG. 5 - TYPICAL JUNCTION CAPACITANCE 0.01 JUNCTION CAPACITANCE, pF 30 TJ=25°C f=1.0 MHZ Vsig=50m Vp-p 1 10 REVERSE VOLTAGE, VOLTS 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 10 1 0 100