1N4383GP THRU 1N4385GP 1N4585GP AND 1N4586GP GLASS PASSIVATED JUNCTION RECTIFIER Reverse Voltage - 200 to 1000 Volts Forward Current - 1.0 Ampere FEATURES E D * DO-204AC T 0.034 (0.86) 0.028 (0.71) DIA. P A T E N 1.0 (25.4) MIN. 0.300 (7.6) 0.230 (5.8) 0.140 (3.6) 0.104 (2.6) DIA. 1.0 (25.4) MIN. ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦1.0 Ampere operation at TA=100°C with no thermal runaway ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension MECHANICAL DATA Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed lead assembly by Patent No. 3,930,306 ® Case: JEDEC DO-204AC molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.015 ounce, 0.4 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 4383GP 1N 4384GP 1N 4385GP 1N 4585GP 1N 4586GP * Maximum repetitive peak reverse voltage VRRM 200 400 600 800 1000 Volts * Maximum RMS voltage VRMS 140 280 420 560 700 Volts * Maximum DC blocking voltage VDC 200 400 600 800 1000 Volts * Maximum average forward rectified current 0.375" (9.5mm) lead length at TA=100°C I(AV) 1.0 Amp * Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TA=100°C IFSM 50.0 Amps VF 1.0 Volts IR 5.0 250.0 µA trr 2.0 µs Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=150°C * Typical reverse recovery time (NOTE 1) Maximum full load reverse current full cycle average at 0.375" (9.5mm) lead length at TA=100°C Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) * Operating junction and storage temperature range IR(AV) 250 225 200 200 µA CJ 15.0 pF RΘJA 45.0 °C/W TJ, TSTG -65 to +175 °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted * JEDEC registered values 4/98 275 UNITS FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG. 1 - FORWARD CURRENT DERATING CURVE 1.0 50 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.9 0.8 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTIC CURVES 1N4383GP THRU 1N4385GP, 1N4585GP AND 1N4586GP 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.375"(9.5mm) LEAD LENGTH 0 25 50 75 100 125 150 175 40 30 20 10 0 200 TA=100°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 AMBIENT TEMPERATURE, °C INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, AMPERES 20 10 TJ=25°C PULSE WIDTH=300µs 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 10 100 NUMBER OF CYCLES AT 60 HZ FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 TJ=125°C 1 TJ=75°C 0.1 TJ=25°C 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 TRANSIENT THERMAL IMPEDANCE (°C/W) FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 100 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec 1 1 10 REVERSE VOLTAGE, VOLTS 100 10 100